Laser-induced thermomigration of Te precipitates in CdZnTe crystals

The thermomigration of tellurium precipitates in a cadmium zinc telluride (CdZnTe) crystal was observed using an infrared (IR) CO₂ laser beam. Te precipitates present in CdZnTe have been shown to thermally migrate along a temperature gradient. Selective energy deposition from an IR laser beam in Te precipitates was investigated as a potentially advantageous approach to speed the annealing of Te precipitates in CdZnTe. Initial results indicate Te precipitates do thermally migrate under IR laser heating.     

Anisotropic vapor phase growth of Ga2O3 crystalline nanobelts

Ga₂O₃ nanobelts were synthesized by gas reaction at high temperature in the presence of oxygen in ammonia. X-ray diffraction and chemical microanalysis revealed that the nanostructures were Ga₂O₃ with the monoclinic structure. Electron microscopy study indicated the nanobelts were single crystalline with broad (0 1 0) crystallographic planes. The nanostructures grew anisotropically with the growth direction of . Statistical analysis of the anisotropic morphology of the nanobelts and electron microscopy investigation of the nanobelt tips indicated that both vapor–solid and vapor–liquid–solid mechanisms controlled the growth process. The anisotropic nature of crystallographic morphology is explained in terms of surface energy.     

Some aspects on thermodynamic properties, phase diagram and alloy formation in the ternary system BAs–GaAs—Part I: Analysis of BAs thermodynamic properties

Owing to the lack of available thermodynamic data based on experimental measurements of heat capacity, decomposition reaction or vapour pressure measurements, the problem of BAs stability is considered. We propose a new set of thermodynamic data for enthalpy of formation, entropy and Gibbs free energy of Bas compound. By using thermodynamic database, our approach is based on the semi-empirical trends and analogy in the variation of those quantities for several binary series in different III–V systems like arsenides, nitrides and phosphides. Thus, the values for BAs were derived by extrapolation from Al to boron-based compounds (BAs, BP and, BN). For pure BAs(s), we predict a low enthalpy of formation in the standard state of at 300 K and a Gibbs free energy of indicating a lower stability of this compound than GaAs. Those values are contradictory discussed with trends in the cohesive energy of several III–V systems. A cohesive energy of 900 kJ/mol (9.4 eV) is proposed in agreement with Philips's rule.     

Electrical properties and deep levels spectra of bulk SiC crystals grown by hybrid physical–chemical vapor transport method

Concentrations of nitrogen shallow donors, boron shallow acceptors, charge carriers, and electron traps were measured as a function of position along the growth axis in a series of undoped 6H–SiC boules grown by sublimation method with and without addition of hydrogen to the growth atmosphere. Elemental analysis by secondary ion mass spectrometry and measurements of electrical properties indicate that the addition of hydrogen suppresses nitrogen incorporation and formation of all electron traps. Concentration of boron is not affected by hydrogen presence. The addition of hydrogen to the growth ambient improves the uniformity of nitrogen incorporation and deep trap distribution along the growth axis. The results are interpreted as due to increased carbon transport and corresponding shift of crystal stoichiometry toward carbon-rich side of the SiC existence range.     

Compensation effect of Mg-doped a- and c-plane GaN films grown by metalorganic vapor phase epitaxy

The electrical and optical properties of Mg-doped a- and c-plane GaN films grown by metalorganic vapor phase epitaxy were systematically investigated. The photoluminescence spectra of Mg-doped a- and c-plane GaN films exhibit strong emissions related to deep donors when Mg doping concentrations are above 1×10²⁰ cm⁻³ and 5×10¹⁹ cm⁻³, respectively. The electrical properties also indicate the existence of compensating donors because the hole concentration decreases at such high Mg doping concentrations. In addition, we estimated the N_D/N_A compensation ratio of a- and c-plane GaN by variable-temperature Hall effect measurement. The obtained results indicate that the compensation effect of the Mg-doped a-plane GaN films is lower than that of the Mg-doped c-plane GaN films.     

Coexistence properties of phase separation and CuPt-ordering in InGaAsP grown on GaAs substrates by organometallic vapor phase epitaxy

CuPt-ordering and phase separation were directly investigated in In_1-xGa_xAs_yP_1-y with a low arsenic content grown by organometallic vapor phase epitaxy on GaAs substrates. CuPt-ordering and phase separation in samples grown at the substrate temperatures of 630 and 690 °C were characterized by transmission electron diffraction and transmission electron microscopy. Although the immiscibility of InGaAsP was enhanced at the lower substrate temperature, the sample grown at 630 °C showed less phase separation than the 690 °C-grown sample. The degree of CuPt-ordering was significantly enhanced in the sample grown at 630 °C. The results demonstrated that the CuPt-ordering originating from surface reconstruction of P(2×4) suppressed the phase separation even in the miscibility gap. The detailed characterization of the phase separation clearly revealed a vertical composition modulation (VCM) in InGaAsP for the first time. The mechanism of the VCM formation is discussed based on the modulated-strain field on the surface.     

Alloy phase separation in InAs/InAlAs/InP nanostructure superlattices studied by finite element calculation

The alloy phase separation effect in InAlAs spacer layer of InAs/InAlAs nanostructure superlattices was studied by two-dimensional finite element calculation. The calculation results showed that InAs islands with wide top would prefer to induce “V”-like In-rich InAlAs arms above InAs islands in InAlAs spacer layer, while InAs islands with narrow top would promote the formation of “I”-like In-rich InAlAs arms above InAs islands in InAlAs spacer layer which corresponded well with the experimental results reported in Ref. [9].     

Atomic ordering in GaAsSb (0 0 1) grown by metalorganic vapor phase epitaxy

Epitaxial GaAsSb (0 0 1) semiconductor alloys grown by metalorganic vapor phase epitaxy exhibit several spontaneously ordered structures. A superlattice structure with three-fold ordering in the [1 1 0] direction has been previously observed by different groups. CuAu structures with (1 0 0) and (0 1 0) ordering planes have also been reported. The physical origin of CuAu ordering in III–V semiconductors has not yet been explained. In this work we report the effect of growth conditions on CuAu ordering in GaAsSb, including miscut from (0 0 1), growth rate, bismuth surfactant concentration, and growth temperature. These data point to a surface kinetic mechanism not based on dimer strain, but possibly due to one-dimensional ordering at step edges.     

The role of Sb in the molecular beam epitaxy growth of 1.30–1.55 μm wavelength GaInNAs/GaAs quantum well with high indium content

Sb-assisted GaInNAs/GaAs quantum wells (QWs) with high (42.5%) indium content were investigated systematically. Transmission electron microscopy, reflection high-energy electron diffraction and photoluminescence (PL) measurements reveal that Sb acts as a surfactant to suppress three-dimensional growth. The improvement in the 1.55 μm range is much more apparent than that in the 1.3 μm range, which can be attributed to the difference in N composition. The PL intensity and the full-width at half maximum of the 1.55 μm single-QW were comparable with that of the 1.3 μm QWs.     

Thermal-induced phase transition and assembly of hexagonal metastable In2O3 nanocrystals: A new approach to In2O3 functional materials

This paper reports on the thermal-induced performance of hexagonal metastable In₂O₃ nanocrystals involving in phase transition and assembly, with particular emphasis on the assembly for the preparation of functional materials. For In₂O₃ nanocrystals, the metastable phase was found to be thermally unstable and transform to cubic phase when temperature was higher than 600 °C, accompanied by assembly as well as evolution of optical properties, but the two polymorphs coexisted at the temperature ranging from 600 to 900 °C, during which the content of product phase and crystal size gradually increased upon increasing temperature. The assembly of In₂O₃ nanocrystals can be developed to fabricate In₂O₃ functional materials, such as various ceramic materials, or even desired nano- or micro-structures, by using metastable In₂O₃ nanocrystals as precursors or building blocks. The electrical resistivity of In₂O₃ conductive film fabricated by a hot-pressing route was as low as 3.72×10⁻³ Ω cm, close to that of In₂O₃ single crystal, which is important for In₂O₃ that is always used as conductive materials. The findings should be of importance for both the wide applications of In₂O₃ in optical and electronic devices and theoretical investigations on crystal structures.     

Investigations on the effect of InSb and InAsSb step-graded buffer layers in InAs0.5Sb0.5 epilayers grown on GaAs (0 0 1)

We report the structural and electrical properties of InAsSb epilayers grown on GaAs (0 0 1) substrates with mid-alloy composition of 0.5. InSb buffer layer and InAs_xSb_1−x step-graded (SG) buffer layer have been used to relax lattice mismatch between the epilayer and substrate. A decrease in the full-width at half-maximum (FWHM) of the epilayer is observed with increasing the thickness of the InSb buffer layer. The surface morphology of the epilayer is found to change from 3D island growth to 2D growth and the electron mobility of the sample is increased from 5.2×10³ to 1.1×10⁴ cm²/V s by increasing the thickness of the SG layers. These results suggest that high crystalline quality and electron mobility of the InAs_0.5Sb_0.5 alloy can be achieved by the growth of thick SG InAsSb buffer layer accompanied with a thick InSb buffer layer. We have confirmed the improvement in the structural and electrical properties of the InAs_0.5Sb_0.5 epilayer by quantitative analysis of the epilayer having a 2.09 μm thick InSb buffer layer and 0.6 μm thickness of each SG layers.     

MOCVD growth of GaN on Si(1 1 1) substrates using an ALD-grown Al2O3 interlayer

GaN thin films have been grown on Si(1 1 1) substrates using an atomic layer deposition (ALD)-grown Al₂O₃ interlayer. This thin Al₂O₃ layer reduces strain in the subsequent GaN layer, leading to lower defect densities and improved material quality compared to GaN thin films grown by the same process on bare Si. XRD ω-scans showed a full width at half maximum (FWHM) of 549 arcsec for GaN grown on bare Si and a FWHM as low as 378 arcsec for GaN grown on Si using the ALD-grown Al₂O₃ interlayer. Raman spectroscopy was used to study the strain in these films in more detail, with the shift of the E₂(high) mode showing a clear dependence of strain on Al₂O₃ interlayer thickness. This dependence of strain on Al₂O₃ thickness was also observed via the redshift of the near bandedge emission in room temperature photoluminescence (RT-PL) spectroscopy. The reduction in strain results in a significant reduction in both crack density and screw dislocation density compared to similar films grown on bare Si. Screw dislocation density of the films grown on Al₂O₃/Si substrates approaches that of typical GaN layers on sapphire. This work shows great promise for the use of oxide interlayers for growth of GaN-based LEDs on Si.     

Phase relations around langasite (La3Ga5SiO14) in the system La2O3–Ga2O3–SiO2 in air

Phase relations around langasite (LGS, La₃Ga₅SiO₁₄) were studied on the basis of phase assemblage observed during calcination and crystallization process of samples of various compositions in the ternary system La₂O₃–Ga₂O₃–SiO₂. A ternary compound of apatite structure, La₁₄Ga_xSi_9–xO_39–x/2 was found for the first time. Crystallization of this compound was observed in the cooling process of molten samples of stoichiometric LGS as well as LGS single crystal, demonstrating that LGS is an incongruent-melting compound. A phase diagram was established primarily based on the crystallization sequence in the cooling process.     

Electrical and optical properties of Cd1−xZnxS (0x0.18) grown by chemical bath deposition

Cd_1−xZn_xS films with 0x0.18 were grown by chemical bath deposition technique on glass substrates from an aqueous solution containing cadmium and zinc sulfate, ammonia and thiourea. Microstructural features, obtained from X-ray diffraction and scanning electron microscopy (SEM) measurements, reveal a predominance of Wurtzite structure and an homogenous microstructure formed by densely microcrystallines for all the samples studied. Cd_1−xZn_xS semiconductor was found to be resistive and of n-type. Also, the electron density decreases with increased x and the mobility reaches a maximum around x=0.12. Which means that the Cd_1−xZn_xS films at this composition are of high crystalline quality, i.e. having reduced intrinsic defect concentrations.     

The photoluminescence of ZnO thin films grown on Si (1 0 0) substrate by plasma-enhanced chemical vapor deposition

High-quality ZnO thin films have been grown on a Si(1 0 0) substrate by plasma-enhanced chemical vapor deposition (PECVD) using a zinc organic source (Zn(C₂H₅)₂) and carbon dioxide (CO₂) gas mixtures at a temperature of 180°C. A strong free exciton emission with a weak defect-band emission in the visible region is observed. The characteristics of photoluminescence (PL) of ZnO, as well as the exciton absorption peak in the absorption spectra, are closely related to the gas flow rate ratio of Zn(C₂H₅)₂ to CO₂. Full-widths at half-maximum of the free exciton emission as narrow as 93.4 meV have been achieved. Based on the temperature dependence of the PL spectra from 83 to 383 K, the exciton binding energy and the transition energy of free excitons at 0 K were estimated to be 59.4 meV and 3.36 eV, respectively.     

Investigation of the role of cadmium sulfide in the surface passivation of lead sulfide quantum dots

Surface passivation of PbS nanocrystals (NC), resulting in strong photoluminescence, can be achieved by the introduction of CdS precursors. The role of CdS in the surface passivation of PbS NCs is uncertain, as the crystalline structure of CdS and PbS are different, which should impede effective epitaxial overgrowth. Absorption spectroscopy is used to show that the CdS precursors strongly interact with the PbS NC surface. Electron microscopy reveals that the introduction of CdS precursors results in an increased particle size, consistent with overcoating. However, we also find the process to be highly non-uniform. Nevertheless, evidence for epitaxial growth is found, suggesting that effective surface passivation may be possible.     

Fabrication of CdS nanorods in inverse microemulsion using HEC as a template by a convenient γ-irradiation technique

Cadmium sulfide (CdS) nanocrystals were successfully prepared in inverse microemulsion under γ-irradiation at room temperature. Their shape can be controlled by changing the surfactant concentrations and the addition of hydroxyethyl cellulose (HEC) as the template. CdS nanorods were successfully obtained under γ-irradiation using HEC as the template, which was confirmed by the observation of transmission electron microscopy (TEM). Without the addition of HEC, spherical CdS crystals were formed. X-ray powder diffraction (XRD) pattern and electron diffraction (ED) analysis showed the hexagonal lattice of CdS in the nanorods. Additionally, the optical properties of CdS nanorods were characterized by ultraviolet–visible (UV–Vis) and photoluminescence (PL) spectroscopy.     

Structural and photoluminescence characteristics of molecular beam epitaxy-grown vertically aligned In0.33Ga0.67As/GaAs quantum dots

In this paper, we present the results of structural and photoluminescence (PL) studies on vertically aligned, 20-period In_0.33Ga_0.67As/GaAs quantum dot stacks, grown by molecular beam epitaxy (MBE). Two different In_0.33Ga_0.67As/GaAs quantum dot stacks were compared. In one case, the In_0.33Ga_0.67As layer thickness was chosen to be just above its transition thickness, and in the other case, the In_0.33Ga_0.67As layer thickness was chosen to be 30% larger than its transition thickness. The 2D–3D growth mode transition time was determined using reflection high-energy electron diffraction (RHEED). Structural studies were done on these samples using high-resolution X-ray diffraction (HRXRD) and cross-sectional transmission electron microscopy (XTEM). A careful analysis showed that the satellite peaks recorded in X-ray rocking curve show two types of periodicities in one sample. We attribute this additional periodicity to the presence of an aligned vertical stack of quantum dots. We also show that the additional periodicity is not significant in a sample in which the quantum dots are not prominently formed. By analyzing the X-ray rocking curve in conjunction with RHEED and PL, we have estimated the structural parameters of the quantum dot stack. These parameters agree well with those obtained from XTEM measurements.     

Self-selecting vapour growth of bulk crystals – Principles and applicability

A method of self-selecting vapour growth (SSVG) for bulk binary and multernary crystals of semiconducting materials is reviewed comprehensively for the first time. Although it has been developed over three decades, the method is less well known – even though it is physically distinct from the more widely used ‘Piper–Polich’ and ‘Markov–Davydov’ vapour transport bulk growth methods. The means by which growth takes place on a polycrystalline source to form a crystal free from the walls is described. Modelling and empirical observations have been used to establish the characteristics of the almost isothermal temperature fields that drive the transport in SSVG. It is demonstrated that precise control of thermal radiation is a fundamental requirement for tailoring the temperature distribution—a fact that has been used well in the design of horizontal tube furnace growth rigs. Achievements in the growth of useful PbS, PbSe, PbTe, CdTe and ZnTe compound crystals are described. The SSVG method has proved to be particularly well suited to the growth of solid solutions, and the results of growth experiments, and of compositional and structural analysis, are presented for Pb(Se,S), (Pb,Sn)Se, (Pb,Sn)Te, (Pb,Ge)Te, Cd(Te,Se), Cd(Te,S) and (Cd,Zn)Te. The excellent compositional uniformity delivered is attributed to entropy driven mixing in the low thermal gradients present in SSVG.

To date, most SSVG has been done at the <50 g level for research or small scale production use. Prospects for scaling up the growth are considered, there being no barriers identified in principle. However, there is a limitation in that the shape of the grown crystals is not accurately controlled at present. To overcome this, and to offer an alternative method of scaling up, the use of vertical tube systems is explored. A significant additional advantage of the vertical configuration is that it allows for continuous recycling of the source/crystal mass so as to continuously self-refine the increasingly uniform – and crystalline – product. Achievements to date in growing II–VI and IV–VI crystals are described for prototype vertical SSVG systems. Finally, future prospects for the SSVG method in terms of further developments to the method, and the specific materials that will benefit from it are highlighted.