Characterization of structure and electrochemical properties of lithium manganese oxides for lithium secondary batteries hydrothermally synthesized from δ-KxMnO2

Lithium manganese oxides have attracted much attention as cathode materials for lithium secondary batteries in view of their high capacity and low toxicity. In this study, layered manganese oxide (δ-K_xMnO₂) has been synthesized by thermal decomposition of KMnO₄, and four lithium manganese oxide phases have been synthesized for the first time by mild hydrothermal reactions of this material with different lithium compounds. The lithium manganese oxides were characterized by powder X-ray diffraction (XRD), inductively coupled plasma emission (ICPE) spectroscopy, and chemical redox titration. The four materials obtained are rock salt structure Li₂MnO₃, hollandite (BaMn₈O₁₆) structure α-MnO₂, spinel structure LiMn₂O₄, and birnessite structure Li_xMnO₂. Their electrochemical properties used as cathode material for secondary lithium batteries have been investigated. Of the four lithium manganese oxides, birnessite structure Li_xMnO₂ demonstrated the most stable cycling behavior with high Coulombic efficiency. Its reversible capacity reaches 155 mAh g⁻¹, indicating that it is a viable cathode material for lithium secondary batteries.     

The effect of B4C addition to MnO2 in a cathode material for battery applications

Boron carbide (B₄C) added manganese dioxide (MnO₂) used as a cathode material for a Zn-MnO₂ battery using aqueous lithium hydroxide (LiOH) as the electrolyte is known to have higher discharge capacity but with a lower average discharge voltage than pure MnO₂ (additive free). The performance is reversed when using potassium hydroxide (KOH) as the electrolyte. Herein, the MnO₂ was mixed with 0, 5, 7 and 10 wt.% of boron carbide during the electrode preparation. The discharge performance of the Zn|LiOH|MnO₂ battery was improved by the addition of 5-7 wt.% boron carbide in MnO₂ cathode as compared with the pure MnO₂. However, increasing the additive to 10 wt.% causes a decrease in the discharge capacity. The performance of the Zn|KOH|MnO₂ battery was retarded by the boron carbide additive. Transmission electron microscopy (TEM), and energy dispersive X-ray spectroscopy analysis (EDS) results show evidence of crystalline MnO₂ particles during discharging in LiOH electrolyte, whereas, manganese oxide particles with different oxygen and manganese counts leading to mixture of phases is observed for KOH electrolyte which is in agreement with X-ray diffraction (XRD) data. The enhanced discharge capacity indicates that boron atoms promote lithium intercalation during the electrochemical process and improved the performance of the Zn|LiOH|MnO₂ battery. This observed improvement may be a consequence of B₄C suppressing the formation of undesirable Mn(III) phases, which in turn leads to enhanced lithium intercalation. Too much boron carbide hinders the charge carrier which inhibits the discharge capacity.     

Electrocatalytic activity of manganese oxides prepared by thermal decomposition for oxygen reduction

The oxygen reduction reaction (ORR) was studied in KOH electrolyte on manganese oxides supported on Vulcan carbon (Mn_yO_x/C). The oxides were prepared by thermal decomposition of manganese nitrate at different conditions. The oxides were characterized by X-ray diffraction (XRD) and in situ X-ray absorption near edge structure (XANES). The electrochemical studies were conducted using cyclic voltammetry (CV) and steady state polarization measurements carried out with a thin layer rotating ring/disk electrode. XRD results showed that the manganese oxide prepared at 200 °C in air is formed by a major phase of β-MnO₂ and the polarization curves indicated the highest activity for this material. In situ XANES evidenced the occurrence of a redox process involving Mn(II)/Mn(III) and Mn(III)/Mn(IV) in the range of potentials of the CV measurements. The electrocalytic activity was related to the occurrence of a mediation process involving the reduction of Mn(IV) to Mn(III), followed by the electron transfer of Mn(III) to oxygen and by a disproportionation reaction of the HO₂⁻ species in the Mn_yO_x sites. In situ XANES results showed that the Mn(IV) species is MnO₂ and the Mn(III) is most likely MnOOH.     

A study of lithium insertion into MnO2 containing TiS2 additive a battery material in aqueous LiOH solution

The electrochemical behavior and surface characterization of manganese dioxide (MnO₂) containing titanium disulphide (TiS₂) as a cathode in aqueous lithium hydroxide (LiOH) electrolyte battery have been investigated. The electrode reaction of MnO₂ in this electrolyte is shown to be lithium insertion rather than the usual protonation. MnO₂ shows acceptable rechargeability as the battery cathode. The influence of TiS₂ (1, 3 and 5 wt%) additive on the performance of MnO₂ as a cathode has been determined. The products formed on reduction of the cathode material have been characterized by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), secondary ion mass spectrometry (SIMS), fourier transform infrared spectroscopy (IR) and transmission electron microscopy (TEM). It is found that the presence of TiS₂ to ≤3 wt% improves the discharge capacity of MnO₂. However, increasing the additive content above this amount causes a decrease in its discharge capacity.     

Electrochemical characterization of amorphous LiFe(WO4)2 thin films as positive electrodes for rechargeable lithium batteries

Amorphous LiFe(WO₄)₂ thin films have been fabricated by radio-frequency (R.F.) sputtering deposition at room temperature. The as-deposited and electrochemically cycled thin films are, respectively, characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, selected area electron diffraction, and X-ray photoelectron spectra techniques. An initial discharge capacity of 198 mAh/g in Li/LiFe(WO₄)₂ cells is obtained, and the electrochemical behavior is mostly preserved in the following cycling. These results identified the electrochemical reactivity of two redox couples, Fe³⁺/Fe²⁺ and W⁶⁺/W^x+ (x = 4 or 5). The kinetic parameters and chemical diffusion coefficients of Li intercalation/deintercalation are estimated by cyclic voltammetry and alternate-current (AC) impedance measurements. All-solid-state thin film lithium batteries with Li/LiPON/LiFe(WO₄)₂ layers are fabricated and show high capacity of 104 μAh/cm² μm in the first discharge. As-deposited LiFe(WO₄)₂ thin film is expected to be a promising positive electrode material for future rechargeable thin film batteries due to its large volumetric rate capacity, low-temperature fabrication and good electrode/electrolyte interface.     

Electrochemical behavior of graphite intercalation compounds of fluorine and metal fluorides

Ternary intercalation compounds, C_xF(AlF₃)_y and C_xF(MgF₂)_y containing active fluorine atoms adsorbed on carbon layers of host graphite were used as a cathode material of lithium cell. The discharge potentials are 2.8–2.5 V at current densities 40–400 μA cm^?2, being higher than that for graphite fluoride below 300 μA cm^?2. X-ray diffraction analysis and ESCA measurement of the discharge products indicate the formation of a new intercalation compound C_x(LiF) (MF_n)_y, (M = Al or Mg, n = 3 or 2).     

Synthesis and electrochemical characterizations of nano-scaled Zn doped LiMn2O4 cathode materials for rechargeable lithium batteries

The LiZn_xMn_2−xO₄ (x = 0.00-0.15) cathode materials for rechargeable lithium-ion batteries were synthesized by simple sol-gel technique using aqueous solutions of metal nitrates and succinic acid as the chelating agent. The gel precursors of metal succinates were dried in vacuum oven for 10 h at 120 °C. After drying, the gel precursors were ground and heated at 900 °C. The structural characterization was carried out by X-ray powder diffraction and X-ray photoelectron spectroscopy to identify the valance state of Mn in the synthesized materials. The sample exhibited a well-defined spinel structure and the lattice parameter was linearly increased with increasing the Zn contents in LiZn_xMn_2−xO₄. Surface morphology and particle size of the synthesized materials were determined by scanning electron microscopy and transmission electron microscopy, respectively. Electrochemical properties were characterized for the assembled Li/LiZn_xMn_2−xO₄ coin type cells using galvanostatic charge/discharge studies at 0.5 C rate and cyclic voltammetry technique in the potential range between 2.75 and 4.5 V at a scan rate of 0.1 mV s⁻¹. Among them Zn doped spinel LiZn_0.10Mn_1.90O₄ has improved the structural stability, high reversible capacity and excellent electrochemical performance of rechargeable lithium batteries.     

Influence of manganese(II), cobalt(II), and nickel(II) additives in electrolyte on performance of graphite anode for lithium-ion batteries

Manganese dissolution into an electrolyte from the spinel LiMn₂O₄ in the lithium-ion cell has been recently investigated. In order to study the influence of the dissolved manganese species on the lithium intercalation/deintercalation into a natural graphite electrode, the electrochemical behavior of graphite was investigated in 1 mol dm⁻³ LiClO₄ electrolyte solution containing a small amount of Mn(II) by the addition of manganese(II) perchlorate. During the charging process, Mn(II) ions were firstly electroreduced on the electrode around 1.0 V versus Li/Li⁺ followed by irreversible decomposition of the electrolyte and lithium intercalation into the graphite. By microscopic observation of the graphite surface, manganese deposition was confirmed after the charge/discharge test. Due to the manganese deposition, the reversible capacity of the graphite electrode was drastically decreased. Furthermore, the cyclability of the anode was degraded with the amount of the manganese additive increasing. We compared these results with those of the cobalt(II) and nickel(II) additives by dissolving the corresponding perchlorates. Furthermore, we discussed the influence in practical cells based on the consideration of electrochemistry of the deposited metals.     

A novel lithium intercalation compound based on the layered structure of lithium nitridonickelates Li3−2xNixN

New lithium nickel nitrides Li_3−2xNi_xN (0.20 ≤ x ≤ 0.60) have been prepared and investigated as negative electrode in the 0.85/0.02 V potential window. These materials are prepared from a Ni/Li₃N mixture at 700 °C under a nitrogen flow. Their structural characteristics as well as their electrochemical behaviour are investigated as a function of the nickel content. For the first time are reported here the electrochemical properties of a lithium intercalation compound based on a layered nitride structure. The Li_3−2xNi_xN compounds can be reversibly reduced and oxidized around 0.5 V versus Li/Li⁺ leading to specific capacities in the range 120-160 mAh/g depending on the nickel content and the C rate. Due to a large number of lithium vacancies, the structural stability provides an excellent capacity retention of the specific capacity upon cycling.     

Synthesis and NTC properties of YCr1−xMnxO3 ceramics sintered under nitrogen atmosphere

YCr_1−xMn_xO₃ (0 ≤ x ≤ 0.8) negative temperature coefficient (NTC) compositions were synthesized by classical solid state reaction at 1200 °C, and sintered under nitrogen atmosphere at 1500 °C and 1600 °C. XRD patterns analysis has revealed that for x ≤ 0.6, the structure consists of a solid solution of an orthorhombic perovskite YCrO₃ phase with Mn substitute for Cr. For x ≥ 0.8, a second phase with a structure similar to the hexagonal YMnO₃ phase appears. SEM images and calculated open porosity have shown that the substitution of Mn for Cr results in a decrease in porosity. Whatever the sintering temperature, the electrical characterizations (between 25 and 900 °C) have shown that the increase in the manganese content involves the decrease in both resistivity and material constant B (parameter which characterizes the thermal sensitivity of material) when x ≤ 0.6. The magnitude order of the resistivity at 25 °C is of 10⁴-10⁸ Ω cm and activation energies vary from 0.28 to 0.99 eV at low and high temperatures, respectively.     

Impact of cobalt substitution for manganese on the structural and electrochemical properties of LiNi0.5Mn0.5O2

A series of LiNi_0.5Mn_0.5−xCo_xO₂ (0 ≤ x ≤ 0.5) compounds was prepared by a solid state reaction, and their structure, surface state and electrochemical characteristics were also investigated by XRD, XPS, EIS and charge-discharge cycling. The non-equivalent substitution of cobalt for manganese induced an increase in the average valence of nickel, thereby shrinking in the lattice volume. Moreover, Co non-equivalent substitution could not only reduce the impurity content but also significantly decreased the charge transfer resistance, thereby improving the rate capabilities.     

Preparation, electrochemical properties, and cycle mechanism of Li1? x Fe0.8Ni0.2O2-Li x MnO2 (Mn/(Fe+Ni+Mn)=0.8) material

A new type of Li_1−x Fe_0.8Ni_0.2O₂-Li _x MnO₂ (Mn/(Fe+Ni+Mn)=0.8) material was synthesized at 350 °C in an air atmosphere by a solid-state reaction. The material had an XRD pattern that closely resembled that of the original Li_1−x FeO₂-Li _x MnO₂ ((Fe+Ni+Mn)=0.8) with much reduced impurity peaks. It was composed of many large particles of about 500–600 nm and small particles of about 100–200 nm, which were distributed among the larger particles. The Li/Li_1−x Fe_0.8Ni_0.2O₂-Li _x MnO₂ cell showed a high initial discharge capacity above 192 mAh/g, which was higher than that of the parent Li/Li_1−x FeO₂-Li _x MnO₂ (186 mAh/g). This cell exhibited not only a typical voltage plateau in the 2.8 V region, but also an excellent cycle retention rate (96%) up to 45 cycles. We suggest a unique role of doped nickel ion in the Li/Li_1−x Fe_0.8Ni_0.2O₂-Li _x MnO₂ cell, which results in the increased initial discharge capacity from the redox reaction of Ni²⁺/Ni³⁺ between 2.0 and 1.5 V region.     

Synthesis and characterization of abundant Ni-doped LiNixMn2−xO4 (x = 0.1-0.5) powders by spray-drying method

The structure and electrochemical properties of LiNi_xMn_2−xO₄ cathode materials for lithium ion batteries were studied by the means of X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscope (TEM), cyclic voltammetry, and galvanostatic charge-discharge tests. The cathodes with different Ni contents (LiNi_xMn_2−xO₄, x = 0.1, 0.2, 0.3, 0.4, and 0.5) were synthesized by a spray-drying method and showed a single-phase spinel structure without any impurity. The amount of Ni has a large effect on the electrochemical characteristics. Capacity values of different voltage ranges (4- and 5-V ranges) change obviously with amount of Ni-doped. Also, the total discharge capacities increase with the Ni content, and all of them have good cycle stability.     

Studies on chemically precipitated Mn(IV) oxides—II

The discharge characteristics of manganese dioxides prepared by chlorate oxidation of Mn(II) salts [Electrochim. Acta28, 309 (1983)] have been evaluated in 9 M KOH solution. The results would seem to indicate that some of the manganese dioxides prepared in this work have a comparatively better discharge performance than the I.C. MnO₂ samples in alkaline electrolyte.     

Beneficial effects of Mo on the electrochemical properties of tin as an anode material for lithium batteries

A simple, novel method for improving the electrochemical response of Sn in lithium cells is proposed that involves preparing Sn by a reduction procedure in the presence of Mo powders. Four different Mo_xSn_1 − x mixtures (0 < x < 0.26) were electrochemically tested and their structural and textural properties determined by using X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and scanning electron microscopy (SEM). The electrochemical properties of the resulting composites in lithium cells were studied by galvanostatic, step potential electrochemical spectroscopy (SPES) and electrochemical impedance spectroscopy (EIS) measurements. The mixtures were found to consist of crystalline Sn and Mo; however, the presence of the latter element modified the Sn habit in two ways, namely, by significantly decreasing particle size and increasing the reactivity towards oxygen. Although Mo is inert towards lithium, it increased both the discharge capacity and the capacity retention of the electrode in relation to pure Sn. The improved interparticle connectivity, reduced electrolyte decomposition and decreased charge-transfer resistance observed in the Mo-containing samples appear to be beneficial effects of the addition of Mo.     

Magnetic and magnetoresistive properties of La0.65−xEuxSr0.35MnO3

Eu-doped perovskites La_0.65−xEu_xSr_0.35MnO₃ (0.05 ≤ x ≤ 0.30) were synthesized by sol–gel method using citric acid and characterized by X-ray diffraction, magnetization, resistivity and magnetoresistance (MR) experiments. All samples had a single hexagonal perovskite structure. As x increased from 0.05 to 0.30, the Curie temperature T_C for the samples decreased from 352 to 242 K. It was found that two transition points appeared when the resistivity changed with increasing temperature, and upon an application of a magnetic field of 20 kOe the maximum magnetoresistivity of 18% for the La_0.65−xEu_xSr_0.35MnO₃ with x = 0.20 was obtained at room temperature 300 K. The mechanism of the transitions for the samples was explored.     

Electrochemical properties of Sr1−xCexMnO3 (0.1≤x≤0.4) – GDC composite cathodes for IT-SOFCs

The electrochemical properties of Sr_1−xCe_xMnO₃ (SCM, 0.1≤x≤0.4)–Gd_0.2Ce_0.8O_2−x (GDC) composite cathodes were determined by impedance spectroscopy. The study focused on the doping effect of Ce in the composite cathodes. Single-phase perovskite was obtained for 0.1≤x≤0.3 in SCM. No reaction occurred between the Sr_0.7Ce_0.3MnO₃ electrode and the GDC electrolyte at an operating temperature of 800 °C for 100 h. In the single phase perovskite region, lattice expansion occurred due to the reduction of Mn⁴⁺ to Mn³⁺ at B-sites, and this was attributed to an increase in Ce content. Ce doping enhanced the electrode performance of SCM–GDC composite cathodes, and best electrode performance was achieved for the Sr_0.7Ce_0.3MnO₃–GDC composite cathode (0.93 Ω cm² and 0.47 Ω cm² at 750 °C and 800 °C, respectively). The improvement in electrode performance was attributed to increases in charge carriers induced by a shift of some Mn from +4 to +3 and to the formation of surface oxygen vacancies caused by Mn⁴⁺ to Mn³⁺ conversion at high temperatures.     

Electrochemical intercalation of lithium into boron-doped CVD diamond electrodes grown on carbon fiber cloths

Boron-doped diamond electrodes grown on a cloth of graphite fibers have demonstrated as an innovative material electrode for lithium intercalation by electrochemical method. It was studied lithium electrochemical intercalation for samples with different levels of boron doping. Diamond films were grown by hot-filament-assisted chemical vapor deposition technique. Boron was obtained from a source of B₂O₃ dissolved in methanol. The electrochemical characterization was carried out by voltammetry cyclic and charge/discharge curves. The electrolyte used was 1 mol l⁻¹ of LiPF₆ in mixture of ethylene carbonate, dimethyl carbonate and diethyl carbonate (1:1:1 wt.). The reference and work electrode were metallic lithium and the cell was assembled a dry-box. The results show that the insertion of lithium Li_x(B_zC_1−z)₆ is reversible and presents specific capacity, which depend on B-concentration. For limits of cut-off potential of 3.0 e 0.01 V vs. lithium we found a reversible specific capacity of 88 mAh g⁻¹ (x∼0.23) for sample with ∼10¹⁸ B cm⁻³ and 43 mAh g⁻¹ (x∼0.11) for sample with 10²¹ B cm⁻³. The voltage vs. capacity presents a hysteresis that increases with decreasing of boron concentration.     

Lead-based systems as suitable anode materials for Li-ion batteries

Three lead-based materials formed by PbO₂, PbO and Pb as main phases were prepared by following different synthetic procedures and tested as anodic materials in Li-ion batteries by using potentiostatic and galvanostatic methods. While the reduction of Pb(IV) to Pb(II) takes place in a single step, that of Pb(II) to Pb is a complex process involving several steps. Both reduction reactions are irreversible. Lead, whether electrochemically or chemically formed, undergoes an electrochemical reaction with lithium that over the 1.0-0.0 V potential range yields Li_xPb alloys (0≤x≤4.4). The anodic and cathodic potentiostatic curves exhibit various signals that account for: (i) the formation of different intermediates with variable lithium contents; (ii) the reversibility of the alloying/de-alloying processes; (iii) the increase in complexity of such processes as the oxidation state of lead in them decreases. This results in capacity fading with cycling, particularly in the samples having Pb as the main component. One way of avoiding the capacity loss on cycling involves depositing the active material on lead sheets from spraying suspensions. These coatings exhibit a good capacity retention, which can be ascribed to the formation of a Li_xPb layer at the active material/substrate interface that facilitates electron and ion transfer across the electrode.     

Study on capacity fade factors of lithium secondary batteries using LiNi0.7Co0.3O2 and graphite-coke hybrid carbon

In our previous work, 10 Wh-class (30650 type) lithium secondary batteries, which were fabricated with LiNi_0.7Co_0.3O₂ positive electrodes and graphite-coke hybrid carbon negative electrodes, showed an excellent cycle performance of 2350 cycles at a 70% state of charge charge-discharge cycle test. However, this cycle performance is insufficient for dispersed energy storage systems, such as home use load leveling systems. In order to clarify the capacity fade factors of the cell, we focused our investigation on the ability discharge capacity of the positive and negative electrodes after 2350 cycles. Although the cell capacity deteriorated to 70% of its initial capacity after 2350 cycles, it was confirmed that the LiNi_0.7Co_0.3O₂ positive electrode and graphite-coke hybrid negative electrode after 2350 cycles still have sufficient ability discharge capacity of 86 and 92% of their initial capacity, respectively. Accompanied by the result for a composition analysis of the positive electrode material by inductively coupled plasma (ICP) spectroscopy and atomic absorption spectrometry (AAS), electrochemical active lithium decreased and the Li_xNi_0.7Co_0.3O₂ positive electrode could be charged-discharged in a narrow range of between x=0.41 and 0.66 in the battery, although it had enough ability discharge capacity that can use between x=0.36 and 0.87. It is predicted that solid electrolyte interface formation by electrolyte decomposition on the carbon negative electrode during the charge-discharge cycle test is a main factor of the decrease of electrochemical active lithium.