PEO-LiClO4-ZSM5复合聚合物电解质 I. 电化学研究

首次以“择形”分子筛ZSM5为填料, 通过溶液浇铸法制得PEO-LiClO₄-ZSM5全固态复合聚合物电解质(CPE)膜. 交流阻抗实验表明ZSM5的引入可以显著地提高CPE的离子电导率. 利用交流阻抗-稳态电流相结合的方法对CPE的锂离子迁移数进行了测定, 结果表明掺入ZSM5后锂离子迁移数明显升高. ZSM5的含量为10%时, CPE同时具有最高离子电导率1.4×10^－5 S•cm^－1(25 ℃)和最大锂离子迁移数0.353. PEO-LiClO₄-ZSM5/Li电极界面稳定性实验表明PEO-LiClO₄-ZSM5复合聚合物电解质在全固态锂离子电池领域具有良好的应用前景.     

PEO-LiClO4-ZSM5复合聚合物电解质 I. 电化学研究

首次以“择形”分子筛ZSM5为填料, 通过溶液浇铸法制得PEO-LiClO₄-ZSM5全固态复合聚合物电解质(CPE)膜. 交流阻抗实验表明ZSM5的引入可以显著地提高CPE的离子电导率. 利用交流阻抗-稳态电流相结合的方法对CPE的锂离子迁移数进行了测定, 结果表明掺入ZSM5后锂离子迁移数明显升高. ZSM5的含量为10%时, CPE同时具有最高离子电导率1.4×10^－5 S•cm^－1(25 ℃)和最大锂离子迁移数0.353. PEO-LiClO₄-ZSM5/Li电极界面稳定性实验表明PEO-LiClO₄-ZSM5复合聚合物电解质在全固态锂离子电池领域具有良好的应用前景.     

PEO基纳米复合聚合物电解质电化学性质的研究

以PEO8 LiClO4作母体,纳米SiO2为填料,制成PEO8 LiClO4 SiO2(x%)系列复合聚合物电解质,测定这该电解质的电导率、锂离子迁移数和电化学稳定窗口,并对其晶态结构作差热分析表征.结果表明,纳米SiO2的引入,显著提高了电解质的电导率,在22℃时达到4.3×10-5S·cm-1.此外,还探讨了填料对复合聚合物电解质电导率提高的影响机理.     

PEO-LiClO_4-ZSM5复合聚合物电解质II.ZSM-5对离子电导率的影响

通过XRD ,DSC ,FT IR和SEM等方法对PEO LiClO4 ZSM5复合电解质进行了研究 ,结果表明ZSM 5可以有效地降低PEO LiClO4 ZSM5复合电解质中PEO的结晶度和玻璃化温度 ,从而提高其低温区域的离子电导率 .温度高于PEO的结晶熔融温度后 ,复合电解质离子电导率的提高则是由于在ZSM 5表面形成了有利于Li离子迁移的导电通道所引起的 .较高的离子电导率和较宽的电化学稳定窗口表明PEO LiClO4 ZSM5复合电解质在全固态锂离子二次电池领域具有良好的应用前景 .     

PEO-LiClO4-ZSM5复合聚合物电解质Ⅱ.ZSM-5对离子电导率的影响

通过XRD,DSC,FT-IR和SEM等方法对PEO-LiClO₄-ZSM5复合电解质进行了研究,结果表明ZSM-5可以有效地降低PEO-LiClO₄-ZSM5复合电解质中PEO的结晶度和玻璃化温度,从而提高其低温区域的离子电导率.温度高于PEO的结晶熔融温度后,复合电解质离子电导率的提高则是由于在ZSM-5表面形成了有利于Li离子迁移的导电通道所引起的.较高的离子电导率和较宽的电化学稳定窗口表明PEO-LiClO₄-ZSM5复合电解质在全固态锂离子二次电池领域具有良好的应用前景.     

高锂离子电导的有机-无机复合电解质的渗流结构设计

固态聚合物电解质被认为是解决传统液态锂金属电池安全隐患和循环性能的关键材料,但仍然存在离子电导率低,界面兼容性差等问题。近年来,基于无机填料与聚合物电解质的高锂离子电导的有机-无机复合电解质备受关注。根据渗流理论,有机-无机界面被认为是复合电解质离子电导率改善的主要原因。因此,设计与优化有机-无机渗流界面对提高复合电解质离子电导率具有重要意义。本文从渗流结构的设计出发,综述了不同维度结构的无机填料用于高锂离子电导的有机-无机复合电解质的研究进展,并对比分析了不同渗流结构的优缺点。基于上述评述,展望了有机-无机复合电解质的未来发展趋势和方向。     

纳米复合全固态聚膦腈电解质

为了进一步提高聚合物电解质的室温离子电导率和锂离子的迁移数,通过对纳米二氧化硅的表面修饰,并采用可聚合的带氧化乙烯-氧化丙烯共聚侧链取代的聚膦腈大单体制备了纳米复合的全固态电解质.通过X射线光电子能谱,扫描电镜,差热扫描分析对纳米复合电解质的性能和形貌进行了分析,并通过交流阻抗考察了电解质与电极间的界面稳定性,用循环伏安表征了电解质的电化学稳定窗口,考察了锂盐含量对电解质离子电导率的影响,测试了电解质的离子电导率随温度的关系,并对锂离子的迁移数进行了测定.研究结果表明,通过纳米复合的方法,提高了聚合物电解质的离子电导率,降低了界面电阻,提高了锂离子迁移率.     

一种高离子电导率复合聚合物电解质的简易热处理制备

固态聚合物电解质是发展柔性全固态锂离子电池的核心,但是目前室温离子电导率低限制了其应用.本研究以热聚合方法制备石墨相氮化碳(g-C_3N_4),并将其与聚氧化乙烯/高氯酸锂(PEO/LiClO_4)共混制备复合聚合物固态电解质.采用X射线衍射(XRD)、傅里叶变换红外光谱(FTIR)、光学显微镜(OM)、扫描电子显微镜(SEM)、差示扫描量热仪(DSC)和电化学工作站对复合聚合物电解质膜进行表征.结果表明,通过120℃退火-淬冷热处理及复合聚合物电解质内部的相互作用,可以较大程度抑制PEO的结晶,从而使该复合聚合物固态电解质膜的离子电导率在25℃时达到2.4×10~(-5)S cm~(-1),提高了3个数量级.     

锂离子电池用聚合物/无机复合固态电解质研究进展

全固态锂离子电池由于具有安全性高、能量密度高等优势,已成为未来锂离子电池发展的必经之路。作为全固态锂离子电池的核心部件,聚合物/无机复合固态电解质同时拥有无机固态电解质和固态聚合物电解质的许多优异性能,但其也面临着诸多挑战,包括室温离子电导率低于10~(-3)S/cm和界面阻抗大等。本文综述了聚合物/无机复合固态电解质的聚合物基体选择,探究了无机填料的种类及其改性方法,以及总结了复合固态电解质膜的制备工艺并对其未来可能的发展方向进行展望。     

表面改性纳米SiO2复合聚合物电解质的制备及性能

通过化学方法将具有增塑效果的环状碳酸酯基团引入纳米SiO2表面,并用FTIR与TGA对改性纳米SiO2进行了表征.将改性纳米SiO2添加到以聚氧化乙烯(PEO)为基体的聚合物电解质中,制备了复合聚合物电解质.通过DSC和交流阻抗等方法对该聚合物电解质膜的热力学和电化学性能进行了研究.结果表明,掺杂改性纳米SiO2的聚合物电解质具有更高的离子电导率,室温最高离子电导率可达到1.84×10-5 S/cm;具有较高的锂离子迁移数,最高可达到0.49,且具有更好的界面稳定性.     

Li1.5Al0.5Ge1.5(PO4)3基固体复合电解质的制备及锂离子导电行为

将聚氧化乙烯(PEO)和二(三氟甲基磺酰)亚胺锂(LiTFSI)混合(固定EO/Li摩尔比为13)后, 采用溶液浇注法制备了一系列不同Li_1.5Al_0.5Ge_1.5(PO₄)₃(LAGP)与PEO质量比的LAGP-PEO(LiTFSI)固体复合电解质体系. 结合电化学阻抗法、 表面形貌表征以及与惰性陶瓷填料(SiO₂, Al₂O₃) 性能的对比分析, 探讨了LAGP在固体复合电解质中的作用机理以及锂离子的导电行为. 结果表明, 在以LAGP为主相的固体复合电解质中, PEO主要处于无定形态, 整个体系主要为PEO与LiTFSI的络合相、 LAGP与PEO(LiTFSI)相互作用形成的过渡相和LAGP晶相. 其中LAGP作为主要的导电基体不仅起到降低PEO结晶度、 改善两相导电界面的作用; 同时自身也可以作为离子传输的通道, 降低锂离子迁移的活化能, 从而使离子电导率得到提高. 当LAGP与PEO的质量比为6:4时, 固体复合电解质的成膜性能最好, 离子电导率最高, 在30 ℃时为2.57×10^-5 S/cm, 接近LAGP的水平, 电化学稳定窗口超过5 V.     

Effect of plasticizers (EC or PC) on the ionic conductivity and thermal properties of the (PEO)9LiTf: Al2O3 nanocomposite polymer electrolyte system

A new plasticized nanocomposite polymer electrolyte based on poly (ethylene oxide) (PEO)-LiTf dispersed with ceramic filler (Al₂O₃) and plasticized with propylene carbonate (PC), ethylene carbonate (EC), and a mixture of EC and PC (EC+PC) have been studied for their ionic conductivity and thermal properties. The incorporation of plasticizers alone will yield polymer electrolytes with enhanced conductivity but with poor mechanical properties. However, mechanical properties can be improved by incorporating ceramic fillers to the plasticized system. Nanocomposite solid polymer electrolyte films (200–600 μm) were prepared by common solvent-casting method. In present work, we have shown the ionic conductivity can be substantially enhanced by using the combined effect of the plasticizers as well as the inert filler. It was revealed that the incorporating 15 wt.% Al₂O₃ filler in to PEO: LiTf polymer electrolyte significantly enhanced the ionic conductivity [σ _RT (max)?=?7.8?×?10^?6 S cm^?1]. It was interesting to observe that the addition of PC, EC, and mixture of EC and PC to the PEO: LiTf: 15 wt.% Al₂O₃ CPE showed further conductivity enhancement. The conductivity enhancement with EC is higher than PC. However, mixture of plasticizer (EC+PC) showed maximum conductivity enhancement in the temperature range interest, giving the value [σ _RT (max)?=?1.2?×?10^?4 S cm^?1]. It is suggested that the addition of PC, EC, or a mixture of EC and PC leads to a lowering of glass transition temperature and increasing the amorphous phase of PEO and the fraction of PEO-Li⁺ complex, corresponding to conductivity enhancement. Al₂O₃ filler would contribute to conductivity enhancement by transient hydrogen bonding of migrating ionic species with O–OH groups at the filler grain surface. The differential scanning calorimetry thermograms points towards the decrease of T _g , crystallite melting temperature, and melting enthalpy of PEO: LiTf: Al₂O₃ CPE after introducing plasticizers. The reduction of crystallinity and the increase in the amorphous phase content of the electrolyte, caused by the filler, also contributes to the observed conductivity enhancement.     

Electrochemical properties of PEO/PMMA blend-based polymer electrolytes using imidazolium salt-supported silica as a filler

In this study, the composite polymer electrolytes (CPEs) were prepared by solution casting technique. The CPEs consisted of PEO/PMMA blend as a host matrix doped with LiClO₄. Propylene carbonate (PC) was used as plasticizer and a small amount of imidazolium salt-supported amorphous silica (IS-AS) as a filler was prepared by the sol–gel method. At room temperature, the highest conductivity was obtained for the composition having PEO–PMMA–LiClO₄–PC–4wt. % IS-AS with a value of 1.15 × 10^?4 S/cm. In particular, the CPE using the IS-AS filler showed a higher conductivity than any other sample (fumed silica, amorphous silica). Studies of differential scanning calorimetry and scanning electron microscopy indicated that the ionic conductivity increase was due to an expansion in the amorphous phase which enhances the flexibility of polymeric chains and the homogeneous structure of CPEs. It was found that the ionic conductivity and interfacial resistance stability of CPEs was significantly improved by the addition of IS-AS. In other words, the resistance stability and maximum ambient ionic conductivity of CPEs containing IS-AS filler were better than CPEs containing any other filler.     

Influence of barium titanate nanofiller on PEO/PVdF-HFP blend-based polymer electrolyte membrane for Li-battery applications

Organic-inorganic hybrid membranes based on poly(ethylene oxide) (PEO) 6.25 wt%/poly(vinylidene fluoride hexa fluoro propylene) [P(VdF-HFP)] 18.75 wt% were prepared by using various concentration of nanosized barium titanate (BaTiO₃) filler. Structural characterizations were made by X-ray diffraction and Fourier transform infrared spectroscopy, which indicate the inclusion of BaTiO₃ in to the polymer matrix. Addition of filler creates an effective route of polymer-filler interface and promotes the ionic conductivity of the membranes. From the ionic conductivity results, 6 wt% of BaTiO₃-incorporated composite polymer electrolyte (CPE) showed the highest ionic conductivity (6 × 10^?3 Scm^?1 at room temperature). It is found that the filler content above 6 wt% rendered the membranes less conducting. Morphological images reveal that the ceramic filler was embedded over the membrane. Thermogravimetric and differential thermal analysis (TG-DTA) of the CPE sample with 6 wt% of the BaTiO₃ shows high thermal stability. Electrochemical performance of the composite polymer electrolyte was studied in LiFePO₄/CPE/Li coin cell. Charge-discharge cycle has been performed for the film exhibiting higher conductivity. These properties of the nanocomposite electrolyte are suitable for Li-batteries.     

PEO/LiClO_4纳米SiO_2复合聚合物电解质的电化学研究

将实验室制备的纳米二氧化硅和市售纳米二氧化硅粉末与PEO LiClO4复合 ,制得了复合PEO电解质 .它们的室温离子电导率可比未复合的PEO电解质提高 1～ 2个数量级 ,最高可以达到 1 2 4× 10 - 5S cm .离子电导率的提高有两方面的原因 :一是无机二氧化硅粉末的加入抑制了PEO的结晶 ,是二氧化硅粉末和聚合物电解质之间形成的界面对电导率的提高也有一定的作用 .在进一步加入PC EC(碳酸丙烯酯 碳酸乙烯酯 )混合增塑剂后制得的复合凝胶PEO电解质 ,可使室温离子电导率再提高 2个数量 ,达到 2× 10 - 3 S cm .用这种复合凝胶PEO电解质组装了Li|compositegelelectrolyte|Li半电池 ,并测量了该半电池的交流阻抗谱图随组装后保持时间的变化 ,实验观察到在保持时间为 144h以内钝化膜的交流阻抗迅速增大 ,但在随后的时间内逐渐趋于平稳 ,表明二氧化硅粉末的加入可以有效地抑制钝化膜的生长     

PEO-LiClO_4-ZSM5 composite polymer electrolyte (IV): Polarized optical microscopy study

All solid-state lithium polymer batteries may be one of the best choices for the future electrochemical power source, characterized by high energy densities, good cyclability, reliability and safety[1,2]. Owing to its potential capability to replace the t…     

Li1.3Al0.3Ti1.7(PO4)3 filler effect on (PEO)LiClO4 solid polymer electrolyte

Composite polymer electrolyte (CPE) films consisting of PEO, LiClO₄, and Li_1.3Al_0.3Ti_1.7(PO₄)₃ with fixed EO/Li = 8 but different relative compositions of the two lithium salts were prepared by the solution casting method. The CPE films were characterized using SEM, DSC, electrical impedance spectroscopy (EIS), and ion transference number measurement. It was found that the incorporation of LiClO₄ and Li_1.3Al_0.3Ti_1.7(PO₄)₃ into PEO by keeping EO/Li = 8 reduced the crystallinity of PEO from 50.34% to the range of 3.57–15.63% depending upon the relative composition of the two salts. The room temperature impedance spectra of the CPE films all exhibited a shape of depressed semicircle in the high frequency range and inclined line in the low frequency range, but the high temperature ones were mainly inclined lines. The Li⁺ ionic conductivity of the CPE films mildly increased and then decreased with increasing Li_1.3Al_0.3Ti_1.7(PO₄)₃ content, and the maximum conductivities were obtained at Li_1.3Al_0.3Ti_1.7(PO₄)₃ content of 15 wt % for all measuring temperatures, for example, 1.378 × 10^?3 S/cm at 100 °C and 1.387 × 10^?5 S/cm at 25 °C. The temperature dependence of the ionic conductivity of the CPE films follows the Vogel–Tamman–Fulcher (VTF) equation The pseudo activation energies (E_a) were rather low, 0.053–0.062 eV, indicating an easy migration of Li⁺ in the amorphous phase dominant PEO. The pre‐exponent constant A and ion transference number t_Li+ were found to have a similar variation tendency with increasing Li_1.3Al_0.3Ti_1.7(PO₄)₃ content and reached their maximums also at Li_1.3Al_0.3Ti_1.7(PO₄)₃ content of 15 wt %. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 743–751, 2005     

CONDUCTING BLENDS OF POLY (2-VINYL PYRIDINE) AND POLYETHYLENE OXIDE WITH HIGH MOLECULAR WEIGHT

Ionic, electronic and mixed (ionic-electronic) conductivities of blends of poly(2-vinylpyridine) (P2VP) and poly(ethylene oxide) (PEO) with high molecular weight after dopedwith LiClO_4, TCNQ or LiClO_4 and TCNQ were investigated. Effects of LiClO_4 and TCNQconcentrations on the conductivity of PEO/P2VP/LiClO_4 or TCNQ blend were studied.The ionic conductivity of PEO/P2VP/LiClO_4 blend increases with increasing PEO content.At a Li/ethylene oxide molar ratio of 0.10 and a TCNQ/2-vinyl pyridine molar ratio of 0.5,the mixed conductivity of PEO / P2VP / LiClO_4 / TCNQ is higher than the total of ionicconductivity of PEO/P2VP/LiClO_4 and electronic conductivity of PEO/P2VP/TCNQwhen the weight ratio of PEO and P2VP is 6/4 or 5/5. Scanning electron microscopy(SEM) on the broken cross-section of the PEO/P2VP/LiClO_4 blend and differential scan-ning calorimetry (DSC) results show that LiClO_4 could act as a compatibilizer in the blend.