离子色谱-质谱联用测定牛奶中的高氯酸盐、溴酸盐和碘离子

以离子色谱-质谱联用同时测定了不同品牌牛奶中的高氯酸盐、溴酸盐和碘离子。以高容量、强亲水性IonPac AS20(2 mm)为分析柱,EGC在线产生KOH为淋洗液,串联质谱检测。ESIMS/MS以多元反应监测(MRM)模式分别监控高氯酸盐的m/z100.8/84.9、98.8/82.9离子对,溴酸盐的m/z126.8/110.9、126.8/95.0离子对和碘离子的m/z126.8/127.0离子对,并分别对高氯酸盐、溴酸盐和碘离子以m/z98.8/82.9、126.8/110.9和126.8/127.0离子对的峰面积进行定量。该方法对高氯酸盐、溴酸盐和碘离子的检出限(S/N=3)分别为0.02、0.1和0.5μg/L,线性相关系数分别是0.999(0.05~50μg/L)、0.999(0.5~100μg/L)、0.998(1~1 000μg/L)。高氯酸盐和碘离子的样品加标回收率分别在102%~108%之间和86%~114%之间。     

离子色谱-质谱联用技术测定饮用水及环境水样中的痕量高氯酸盐

建立了一种测定痕量高氯酸盐的离子色谱-质谱联用方法.选用高容量、强亲水性的阴离子交换柱IonPac AS20(2 mm)进行分离,以淋洗液自动发生器在线产生的KOH为淋洗液,采用等浓度淋洗.在不添加有机溶剂的情况下,淋洗液经过抑制器抑制后直接进入电喷雾-串联质谱(ESI-MS-MS),以负离子模式进行检测.同时采用多元反应监测(MRM)模式对高氯酸盐进行监控,以100.8/84.9、 98.8/66.9和100.8/68.9为监控离子对,以98.8/82.9离子对的峰面积进行定量.高氯酸盐质量浓度在0.05～50 μg/L范围内具有良好的线性(r＝0.9985),检出限(S/N=3)为0.01 μg/L.将该方法用于饮用水以及地下水、雪水等环境水样中高氯酸盐的分析,并进行了加标回收实验,回收率在86%～110%之间,将实际自来水样品连续11次进样,所得高氯酸盐的峰面积的相对标准偏差(RSD)为1.6%.     

大体积进样离子色谱法测定环境水样中高氯酸根

采用大体积500μL进样离子色谱法,电导检测测定了几种水体中高氯酸盐的含量。分析柱为容量高、亲水性强的以脂肪族碳骨架为基质的阴离子交换柱IonPac AS20,淋洗液在线发生器自动产生35 mmol/LKOH淋洗液,0.25 mL/m in等浓度淋洗。这种新型的以脂肪族碳骨架为基质的阴离子交换柱的采用,极大的削弱了该色谱柱对对氯苯磺酸的保留,完全消除了现行美国EPA高氯酸盐分析方法中高氯酸根与对氯苯磺酸共淋洗的问题。方法对高氯酸根的检出限(S/N=3)为0.5μg/L,高氯酸根浓度在1~1000μg/L范围内具有良好的线性(r=0.9991)。将本方法应用于自来水、河水和雪水样品中高氯酸盐的检测,实际样品的加标回收率在87%~114%之间;1μg/L高氯酸根连续进样9次,色谱峰面积相对标准偏差(RSD)为6.9%。     

超高效液相色谱-电喷雾离子源-串联三重四极杆质谱分析饮用水中的高氯酸盐

建立了超高效液相色谱-电喷雾离子源-串联三重四极杆质谱(UPLC-ESI MS/MS)分析饮用水中高氯酸盐的方法.以300Extend-C18为分析柱,10%甲醇水溶液为流动相,ESI MS/MS串联质谱为检测器,以多重反应监测(MRM)模式监测高氯酸盐m/z 99.5→82.9离子对.方法的线性范围为0.2 ～10 μg/L,相关系数为r2=0.999 9,方法检出限为0.15 μg/L,平均加标回收率为82%,相对标准偏差为4.4%.应用UPLC-ESI MS/MS法测定北京市部分城区饮用水中的高氯酸盐,其中5个水样中检出ClO-4,质量浓度为0.040 ～0.262 μg/L,但在安全阈值范围内,不会对居民健康构成威胁.     

大体积进样–Ag柱除氯–离子色谱法测定水中溴酸盐

建立以大体积进样(250μL)–离子色谱测定水中溴酸盐(BrO_3~–)的方法。采用Ag柱离线去除样品中大量Cl~–以消除Cl~–干扰,同时保证痕量溴酸盐未沉淀,过滤后直接进样测定。BrO_3~–的质量浓度在2.0~25.0μg/L范围内与色谱峰面积呈良好的线性关系,线性相关系数r=0.999 2,方法检出限为0.8μg/L。自来水和矿泉水样品3浓度水平加标回收率为85.0%~101.0%,测定结果的相对标准偏差为3.6%~12.9%(n=6)。该方法样品处理简单,检出限低,准确度和精密度高,满足分析测试的要求。     

离子色谱-串联质谱法测定婴幼儿配方奶粉中的高氯酸盐

采用离子色谱-串联质谱法测定婴幼儿配方奶粉中的高氯酸盐。将2.00g样品溶解在10mL水中,加入乙腈10mL,振荡离心去除样品中的蛋白质,上清液用10mL乙腈饱和的正己烷溶液去除样品中的脂类物质。净化液采用Dionex IonPac AS 20色谱柱分离,以60mmol·L~(-1)氢氧化钾溶液洗脱。质谱中采用电喷雾离子源和多反应监测模式,以NaCl 18O4作为同位素内标物质定量。高氯酸盐质量浓度的线性范围为0.1~100μg·L~(-1),检出限(3S/N)为0.3μg·kg~(-1),测定下限(10S/N)为1.0μg·kg~(-1)。加标回收率在92.1%~97.0%之间,测定值的相对标准偏差(n=6)小于10%。     

液相色谱-质谱联用法测定人血浆中的阿莫西林

建立液相色谱–质谱联用法测定人血浆中的阿莫西林。在血浆样品中加入20μL 10μg/mL的阿莫西林-d4内标溶液,再经甲醇沉淀。色谱柱为Zorbax Eclipse XDB–C18(150 mm×2.1 mm,3.5μm),柱温为30℃,流动相为0.2%甲酸水溶液与0.2%甲酸甲醇溶液,采用梯度洗脱方式,流量为0.7 mL/min,进样体积为3μL;质谱采用电喷雾离子化方式和质谱多反应监测模式,检测离子为正离子。阿莫西林的质量浓度在0.05~10μg/mL范围内与其色谱峰面积呈良好的线性关系,相关系数为0.999 7,检出限为0.05μg/mL。测定结果的相对标准偏差小于3%(n=6),样品加标回收率为91.1%~97.3%。该方法操作简便,灵敏度高,专属性强,可用于测定人血浆中阿莫西林的含量。     

气相色谱–质谱联用法测定空气中的丙烯腈

建立测定空气中丙烯腈的气相色谱–质谱联用方法。用活性炭管采集样品,以体积分数为2%的丙酮二硫化碳溶液解吸,利用气相色谱–质谱法以选择离子扫描方式采集数据并进行分析,以色谱峰面积外标法定量。丙烯腈的质量浓度在0~100μg/m L范围内与色谱峰面积线性关系良好,线性相关系数(r~2)为0.999 0。丙烯腈检出限为1.2μg/m L,最低检出质量浓度为0.16 mg/m~3(以采样体积7.5 L计),平均加标回收率为97.0%~99.3%,测定结果的相对标准偏差为3.0%~4.2%(n=6)。该方法定性、定量准确,精密度、灵敏度高,可用于空气中丙烯腈的常规检测。     

HPLC法测定土圞儿根皮和块根中的西瑞香素

建立高效液相色谱法测定土圞儿根皮和块根中西瑞香素含量的方法。采用Kromasil C18色谱柱(250mm×4.6 mm,5μm),以甲醇–0.2%磷酸水溶液(56∶44)为流动相等度洗脱,流量为1.0 m L/min,柱温为35℃,检测波长为345 nm。西瑞香素的质量浓度在20~100μg/m L内与色谱峰面积呈现良好的线性关系,线性相关系数r=0.999 9,方法精密度(RSD)为1.23%(n=6)。根皮样品、块根样品的加标回收率分别为98.8%,98.2%,测定结果的相对标准偏差分别为1.30%,2%(n=6)。该方法快速可靠,可用于土圞儿药材的质量控制。     

抑制型电导检测离子色谱法测定饮用水中高氯酸盐

建立抑制型电导检测离子色谱法测定饮用水中的高氯酸盐。选用IonPac^?AS19色谱柱(250 mm×4 mm)，柱温为30℃，电导池温度为35℃，用40 mmol/L氢氧化钾溶液作为淋洗液，氢氧化钾淋洗液由淋洗液发生器在线产生，淋洗液流量为1.0 mL/min，淋洗方式为等浓度淋洗。采用AERS 500(4 mm)型抑制器，抑制器电流为99 mA，进样体积为500μL，高氯酸盐的色谱峰面积与质量浓度在0.030～0.200 mg/L范围内的线性关系良好，相关系数为0.999 2，方法检出限为0.002 mg/L，定量限为0.010 mg/L。7次重复测定结果的相对标准偏差为2.49%～3.78%，样品加标回收率为90.0%～101%。该方法适用于饮用水中高氯酸盐的检测。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.