驾驶员属性对信号灯路口交通流的影响研究

采用元胞自动机模型研究信号灯路口的交通流特性,系统地分析了与性别、驾驶经验、性格等驾驶员属性相关的驾驶行为对交通流的影响.数值模拟发现,技术生疏或紧张驾驶、急躁行驶等驾驶行为更易引发自由流到阻塞流的相变,是路口通行低效率及事故隐患的重要原因,信号周期是影响流量与个人通行时间公平的主要因素.     

信号灯和公交车站对T形路口交通流的影响研究

采用非线性映射模型研究T形路口的交通问题,利用点平均流量指标系统地分析了公交车站、信号灯周期、绿信比、车辆左右转弯等因素对路径交通流量的影响.数值模拟结果表明,信号灯和公交车站之间的相互影响容易导致交通流的串现象,不同路径上的流量与信号灯周期、绿信比和公交车站位置之间存在一定的关系. 关键词： 交通流 非线性映射模型 信号控制 串     

基于元胞自动机模型的上匝道合流处交替通行控制的研究

上海市高架道路的上匝道合流处率先实施了交替通行的控制策略.以Fukui和Ishibashi提出的FI元胞自动机交通流模型为基础，对实施该策略前后的上匝道合流处分别建立合理的交通流模型，并对交通流进行了数值模拟和分析.结果表明：当高架路主线和上匝道的来流车辆较多时，交替通行控制可以大大改善高架道路交通；当交通流稀疏时，实施控制前后交通流状况基本不发生变化. 关键词： 元胞自动机模型 上匝道合流处 交替通行控制 数值模拟     

交通灯控制下城市主干道双车道多速元胞自动机交通流模型研究

提出一个城市主干道双车道多速元胞自动机交通流模型，此模型采用开放性 边界条件，在考虑诸多实际因素影响情况下，研究了主干道中车站的设置、交通灯绿信比对 车流量和车流速度的影响.计算机模拟所得到的基本图（流量 速度图）能较好地反映在交 通灯控制下城市主干道交通流真实状况. 关键词： 元胞自动机模型 交通流 主干道     

考虑实施过程的车辆换道模型及其应用

通过对现有换道模型进行改进,提出了一种考虑换道实施过程的模型,并对模型中的关键参数进行了标定.由于该模型考虑了换道实施过程中车辆换道对交通流的影响,新模型的模拟结果与实测值更为符合.运用新模型对不同车道数的道路交通流进行模拟,发现不同车道数的平均每车道通行能力及其交通流特性存在显著差异. 关键词： 换道模型 换道时间 车道数 道路通行能力     

车道尺度对平面环行交叉路口流量影响的研究

运用具有内、外环道的平面环形交叉路口元胞自动机模型,利用交通流基本图从瓶颈的角度研究了车道尺度对平面环行交叉路口交通流的影响。计算机模拟结果表明:同步增加内、外环道长度时,内环道流量将会增加;同步增加入、出环车道长度时,内环道流量保持不变。     

多路段元胞自动机交通流模型

在经典单路段元胞自动机交通流模型的基础上,将多个路段视为一个道路系统,提出并研究了多路段条件下的交通流问题.针对多路段道路的特点,通过引入车辆流入规则、路口随机慢化规则和路口车辆流入规则,控制车辆从上一路段流入下一路段.首先提出了"汽车池"的概念,来控制每一路口车辆的流入;然后通过路口随机慢化,来模拟路口对交通的影响;最后,当车辆离开时,依直行率进入下一路段,实现车流的继续流动.同时,通过数值模拟,仿真了不同条件下的交通情况,对重要参数进行了研究.结果表明,出现了混合流这一新的现象,拥堵地段与非拥堵地段间存在明显的界限.拥堵往往最先从路口开始,然后蔓延到整个路段.多路段道路还存在临界突变的特性.随着车辆流入概率的增大,路口对平均速度和车流密度的影响愈加明显.当流入概率超过一定阈值时,车辆缓慢地增加也会引起整体道路通行能力的迅速下降.     

城市道路U形转向交通流特性模拟分析

以NaSch模型为基础建立设置U形转向的路段交通流模型,对其特性进行模拟分析. 结果表明,U形转向路口对交通流影响显著,会导致在较小进车概率时发生自由流状态到拥挤状态的相变,相应的临界流量也随之降低. 设置双U形转向系统的相变、临界流量等交通流特性与单转向系统具有明显差异,其系统效率较高. 在实际交通规划与管理时应避免设置单转向系统,以减小U形转向的负面影响. 关键词： 交通流 元胞自动机 U形转向 相变     

机动车协商模型与分岔特性研究

在环行交叉路口交通流中, 由于行驶目的的不同存在三种类型冲突. 为了真实模拟人类的自治性和智能性, 先将机动车建立为一个含有驾驶员模型的智能体, 再耦合环行交叉口的元胞自动机模型组成多智能体系统. 在总结每种类型交通冲突特点和规律的基础上, 提出通过优先级策略和动态协商机制消解机动车智能体相互之间的冲突问题. 以某中小城市城的典型环行交叉路口交通流量为样本数据, 对比验证模型的正确性, 并且进一步研究了交通流的分岔特性, 发现一定条件下流量的周期分岔和混沌现象. 数值模拟结果表明, 所建模型符合实际情况, 并且内环发生冲突越严重车流量越低, 随着机动车属性参数k和p的变化, 系统从稳定走向分岔再到混沌. 关键词： 多智能体 元胞自动机 协商 分岔     

双下匝道系统的交通流动态特征及其优化

利用多车道元胞自动机模型研究双下匝道系统的交通流动态演化特征.采用可变情报板来实现交通诱导,着重分析驾驶员选择目标匝道的决策行为及其对道路通行能力的影响.分别建立了无可变情报板的基本模型和有可变情报板的诱导模型.通过数值模拟,分别给出了相应的相图、道路通行能力、流量图和时空斑图,分析了进车概率、出车比例和出车道长度对交通行为的影响.通过对两个模型模拟结果的比较分析,发现当出车道长度较小而进车概率、出车比例都较大时,可变情报板的诱导信息能明显提高下游匝道的利用率,改善道路交通流状况,从而缓解交通拥堵.     

交通灯控制下主干道的交通流研究

用元胞自动机模型模拟二维交通流.通过交叉口设置的红绿灯，研究交通激波的形成和传播 ；对于一定的红绿灯周期，交通流量出现多个极值现象；在交叉口间隔相同的情况下，对于 一定的红绿灯周期，在一定的车辆密度范围内，交通流量是一个与密度无关的常量；在车辆 密度较高的情况下，交叉口间距大于某一值后，交通流量保持恒定值. 关键词： 元胞自动机模型 交通流 交通激波     

Computer simulation model for the prediction of traffic noise levels

This paper describes a computer simulation model capable of predicting the noise levels generated by traffic passing through road intersections controlled by roundabouts where departures from free-flow traffic conditions occur. The model depends for its operation on the acoustical and flow characteristics of single vehicles travelling on a road from which the overall noise generated by traffic streams can be deduced using a sampling/integration technique. Distance effects, ground cover, vehicle type, velocity and headway characteristics, etc. are taken into account in the model and the simplest possible input parameters are used deliberately to facilitate the eventual use of the model by highway and planning authorities. Good agreement has been achieved between measured and predicted L₁₀ values for freely flowing traffic negotiating roundabouts. Further applications of the model involving road intersections controlled by traffic lights and the effect of traffic queues are nearing completion.     

Techniques for the investigation of road traffic noise in regions of restricted flow by the use of digital computer simulation methods

Computer methods of calculating and predicting the noise from road traffic operating in restricted flow conditions are discussed. A method of calculating the noise from road traffic as a function of the manoeuvring parameters by means of a Monte Carlo digital computer simulation model is briefly described. The model is used in deriving correction contours for single streams of traffic which enable free flow L₁₀ levels to be modified to allow for a flow restriction. Flow restrictions of the type encountered at traffic signals, priority intersections and pelican crossings are considered. The contours cover a stretch of road 600 m long and a distance of 60 m from the kerb line and in general show a reduction in L₁₀ level in transferring from the free to the restricted flow situation. A method of applying the contours as a modification of the United Kingdom Department of the Environment prediction method for L₁₀ is proposed and compared with experimental results. Computer simulation models of complete road intersections are discussed. Two types of intersection controls are considered, the traffic signal control and the roundabout. The results of the two types of simulation are compared and the L₁₀ level adjacent to the accelerating traffic streams is generally found to be greater than that adjacent to decelerating streams. Experimental results for both types of intersection are compared with simulation runs in which the observed traffic parameters are used.     

A macro traffic flow model accounting for road capacity and reliability analysis

Based on existing traffic flow models, in this paper we develop a macro traffic flow model taking into consideration road capacity to study the impact of the road capacity on traffic flow. The numerical results show that the road capacity destroys the stability of uniform flow and produces stop-and-go traffic under a moderate density and that the road capacity enhances the traffic risk coefficient and reduces the traffic system’s reliability. In addition, the numerical results show that properly improving the road condition can enhance the road capacity, reduce the traffic risk coefficient and enhance the traffic system’s reliability.     

道路交通的流体物理模型与粒子仿真方法

针对受多种因素影响的复杂道路交通系统问题,基于颗粒动力学理论,结合传统的Lighthill-WhithamRichards物理模型,建立道路交通系统的流体物理模型,采用无网格粒子与网格相结合的方法进行数值仿真,并应用于典型道路交通问题的求解.在新模型中,将车辆比拟为硬颗粒,车辆的跟车比拟为颗粒间的碰撞相互作用,已知道路情况对驾驶员操作车辆的影响比拟为流-粒两相系统中的外部流体驱动力作用,不同车道间车辆的影响比拟为颗粒间的黏性作用,从而在颗粒动力学理论的基础上,推导建立了道路交通系统拟流体模型;引入光滑离散颗粒流体动力学(SDPH)对车辆系统模型进行离散,建立"SDPH车辆"与真实车辆之间的一一对应关系,再结合有限体积方法,对道路交通构建的双流体模型进行求解,建立求解交通流体物理模型的新型仿真方法.最后,采用所建立的模型和方法对车辆汇入以及机非混合对交通系统的影响过程进行了数值仿真,所得结果与实测值符合较好,表明新的模型和方法有效性好、可靠性高,为道路交通问题的解决提供了一条全新的途径.     

Noise at the approach to traffic lights: Result of a simulation programme

This paper describes a computer model of the acoustic behaviour of road traffic at the approach to a system of traffic lights. The outputs of this model consist of various acoustic signatures of the traffic at different points along the roadside. These signatures are a good approximation to those determined at real locations under similar conditions. Use of the model leads to a better understanding of the phenomena involved and the derivation of laws as a function of parameters such as traffic flow, speed limits, proportion of heavy vehicles and the traffic light cycles and synchronization.     

Long-range correlation analysis of urban traffic data

<正>This paper investigates urban traffic data by analysing the long-range correlation with detrended fluctuation analysis.Through a large number of real data collected by the travel time detection system in Beijing,the variation of flow in different time periods and intersections is studied.According to the long-range correlation in different time scales, it mainly discusses the effect of intersection location in road net,people activity customs and special traffic controls on urban traffic flow.As demonstrated by the obtained results,the urban traffic flow represents three-phase characters similar to highway traffic.Moreover,compared by the two groups of data obtained before and after the special traffic restrictions(vehicles with special numbered plates only run in a special workday) enforcement,it indicates that the rules not only reduce the flow but also avoid irregular fluctuation.     

信号灯控制下的主道双车道入匝道系统交通流特性研究

采用元胞自动机模型研究了具有信号灯控制的主道为双车道的入匝道系统交通流特性.将信号灯设置在入匝道口处,通过信号灯来引导主道和匝道上的车辆通行.分析了信号灯控制对主道与匝道的车流量、系统通行能力以及入匝道口处的车流平均速度的影响.通过相图比较,说明信号灯控制的双车道入匝道系统能模拟出比信号灯控制的单车道入匝道系统更加符合实际的交通流特性.与姜锐提出的模型［Jiang R 2003 J. Phys. A 36 11713］结果相比,信号灯控制下的匝道系统的交通流状态得到改善并且道路通行能力有所提 关键词： 交通流 元胞自动机 入匝道系统 信号灯     

Delay times in a cellular traffic flow model for road sections with periodic outflow

A simple cellular automaton to model traffic flow is used to analyze the impact of traffic lights on travel times. The model is investigated on a stretch of road with open boundaries, where the inflow is driven stochastically, but the outflow is controlled by a traffic light with periodically changing outflow rates. Especially in the transition regime from free flow to oversaturated flow, the detailed space-time structure can be used to derive analytical lower and upper boundaries for the travel time function. The analytical results have been verified by a simulation study. The function displays a strong non-trivial dependency on the length of the system, which is at odds with a well-known formula derived almost 50 years ago by Webster. Such a model is interesting both from a theoretical point of view and for applications.