渐变强化刃刀具硬切削过程切屑流动和刀具磨损研究

刃口倒棱结构在提升切削刃强度的同时也进一步增大了切削过程中的热力载荷,进而影响着硬切削加工的切屑流动、刀具磨损和加工表面质量。利用高速摄影方法,对比分析了渐变强化刃和定值倒棱两种结构PCBN刀具的切屑流动特性,发现渐变强化刃结构具有协调切屑流动的作用,能有效地解决硬切削过程切屑积聚问题。结合硬切削试验,开展了渐变强化刃刀具磨损特性研究,结果表明：与定值倒棱刀具相对集中的磨损带不同,渐变强化刃刀具磨损区域则更为狭长,后刀面磨损带呈现为长三角形,具备了更为优异的刃口保持性和耐用度,当进入到刃形改变阶段,其磨损机制由磨粒磨损机制逐渐变化为磨粒、氧化和扩散等多种机制的混合形式。渐变强化刃结构刀具在改善切屑流动和提升刀具耐用度方面均体现出了明显的优势,具备了良好的推广应用前景。     

激光超声复合切削硬质合金的刀具磨损及其对工件表面质量的影响

基于激光加热辅助切削和超声椭圆振动切削提出了激光超声复合切削加工工艺。采用聚晶立方氮化硼(PCBN)刀具对YG10硬质合金进行了常规切削,超声椭圆振动切削,激光加热辅助切削和激光超声复合切削对比试验。检测了刀具磨损量、刀具磨损形貌、工件表面粗糙度以及工件表面形貌,并通过扫描电镜(SEM)对刀具磨损区域进行了能谱分析,同时研究了激光超声复合切削硬质合金时PCBN刀具的磨损及其对工件表面质量的影响。最后,与常规切削、超声振动切削及激光加热辅助切削进行了对比试验。结果表明:激光超声复合切削时刀具使用寿命显著增加,加工后的工件表面粗糙度平均值分别降低了79%、60%和64%,且工件表面更加平整光滑。激光超声复合切削硬质合金时,PCBN刀具的前刀面磨损表现为平滑且均匀的月牙洼磨损,后刀面磨损表现为较窄的三角形磨损带和较浅的凹坑和划痕;刀具的失效机理主要为黏接磨损、氧化磨损和磨粒磨损的综合作用。     

PCBN刀具切削GCr15淬硬轴承钢时刀具磨损的研究

通过切削实验，研究了PCBN刀具切削淬硬轴承钢时刀具磨损形态及磨损机理。实验表明。PCBN刀具前刀面的磨损为月牙洼磨授，后刀面的磨损为机械磨损，其磨损程度与工件硬度呈非线性关系，并随着切削速度的提高磨损量减少。     

PCBN刀具高速切削抗氢钢HR-2的性能研究

采用不同CBN含量和晶粒结构的PCBN刀具,在不同切削速度下进行了HR-2抗氢钢的高速精密切削试验。通过对PCBN刀具前、后刀面的显微形貌特征进行观测,分析了刀具的失效磨损机理,研究了不同CBN含量及不同切削速度对刀具使用寿命的影响。对刀具磨损的测量结果表明,PCBN刀具高速切削HR-2时,CBN含量高的刀具显示出更长的使用寿命,且在130-200m/min区间为最佳切削速度区域。SEM和EDS分析结果表明,高速精密切削HR-2的磨损机理为氧化磨损、扩散磨损、粘结磨损,同时存在磨粒磨损以及引起的微崩刃现象。     

Crater and flank wear resistance of cutting tools having micro textured surfaces

We have proposed cutting tools with various textured surfaces to increase cutting tool life. Our previous studies have developed cutting tools having periodical stripe-grooved surfaces on their rake face formed using femtosecond laser technology, which displayed high crater wear resistance in cutting of steel materials. In this study, the mechanism for suppressing the crater wear on the tool surface and the relationship between texture dimensions and wear resistance were investigated to provide a guideline for developing tools with textured surfaces. Furthermore, we newly introduced the textured surfaces into a flank face of cutting tools to improve flank wear resistance. Face milling experiments on steel materials exhibited that the newly developed tool having the textured flank face significantly reduced the flank wear. Moreover, the influences of texture dimensions and cutting conditions on the flank wear resistance were also discussed.     

钛合金铣削过程刀具前刀面磨损解析建模

钛合金Ti6Al4V作为典型的航空航天难加工材料,在其铣削过程中硬质合金刀具的磨损会降低加工过程稳定性,进而影响加工效率和已加工表面表面质量。刀具前刀面磨损会导致刀具刃口强度降低,并影响切屑的流向和折断情况。针对前刀面磨损机理进行分析并构建了月牙洼磨损深度预测模型。首先运用解析方法构建了前刀面应力场模型,得到切屑在前刀面滑动过程中的刀具前刀面应力分布情况及磨损位置。基于刀-屑接触关系的基础上建立了前刀面温度场模型。然后,基于所得刀具前刀面应力与温度分布,构建综合考虑磨粒磨损、粘结磨损与扩散磨损的铣刀月牙洼磨损深度预测模型,获得月牙洼磨损预测曲线;结合铣刀月牙洼磨损带沿切削刃方向分布的特点,建立了随时间变化的铣刀前刀面磨损体积预测模型。最后通过试验验证了切削宽度对前刀面磨损的影响规律,预测结果与试验测量值具有较好的吻合性。结果表明随着切削宽度的增加,月牙洼磨损深度及前刀面磨损体积都随之增加。研究结果为钛合金铣削用刀具的设计和切削参数的合理选择提供了理论基础。     

陶瓷刀具和PCBN刀具磨损形态的研究

对陶瓷刀具(CC650)和PCBN刀具(CB20)精车淬硬GCr15轴承钢时的刀具磨损形态及性能进行了对比试验；结合扫描电镜对刀具的磨损形态作观察；分析了刀具磨损特征及磨损机理。结果表明：刀具损坏的形态主要为前刀面磨损、后刀面磨损、微崩刃及破损等；陶瓷刀具和PCBN刀具的前后刀面磨损形态不同于典型的磨损形态，陶瓷刀具主后刀面的磨损量要比PCBN刀具的磨损量小。但两种刀具均适合于淬硬钢的精加工工序。     

AN EXPERIMENTAL EVALUATION OF CUTTING TEMPERATURES DURING HIGH SPEED MACHINING OF HARDENED D2 TOOL STEEL

This paper investigates experimentally the effects of different process parameters on the cutting edge temperature during high speed machining of D2 tool steel using polycrystalline cubic boron nitride (PCBN) tools. The cutting edge temperature is measured using thermocouples. The process parameters considered are cutting speed, feed rate, nose radius, rake angle, and tool wear. The effects of different edge preparations including sharp, honed and chamfered are also investigated. The results show that increasing cutting speed and feed rate increases the cutting temperature while increasing nose radius reduces the cutting edge temperature. In addition, there is an optimum rake angle value at which minimum cutting temperature is generated.     

Ultraprecision turning of electroless nickel: effects of crystal orientation and origin of diamond tools

This paper deals with (i) the performance of natural and artificial diamond tools and (ii) the effects of crystal orientations at rake face of diamond tool for long distance (>200 km) ultraprecision machining of electroless nickel. The criteria for cutting performance of the diamond tool include flank wear, crater wear, workpiece surface finish, and cutting forces. Experimental results show that the natural diamond tool has superior performance compared to the artificial one as it experienced lower cutting forces and lower flank and crater wears. It was also found that the cutting tool with {110} crystal orientation at rake face performs better than the tool with {100} crystal orientation in terms of amount of wear, surface finish, and cutting forces.     

铁基粉末冶金材料的高速干切削试验研究

用陶瓷刀具、涂层刀具和硬质合金刀具进行了铁基粉末冶金零件的干切削对比试验,研究了切削速度、切削深度以及进给速度与刀具耐用度和加工表面粗糙度的关系,分析了陶瓷刀具的磨损机理。结果表明所选用陶瓷刀具的切削性能明显优于涂层刀具和硬质合金刀具;陶瓷刀具前刀面主要磨损形式为月牙洼磨损与剥落,后刀面的主要磨损原因为磨粒磨损;认为陶瓷刀具更适合用于粉末冶金零件的切削加工。     

高速车削钛合金时PCBN刀具寿命的研究

采用对角正交回归试验法,研究了用PCBN刀具高速车削钛合金TC4时切削用量对刀具寿命的影响,并分析工件已加工表面粗糙度。通过扫描电镜观察分析,证实刀具的磨损机理主要是前后刀面的粘结磨损及氧化磨损、后刀面磨损以及切削深度线处的沟槽磨损。     

PCBN刀具切削镍基高温合金刀具磨损的试验研究

通过PCBN刀具对镍基高温合金GH4169进行了车削试验,深入研究了切削时的刀具磨损形态及磨损原因,得出如下结论:通过试验观察看出刀具的磨损形态有前刀面磨损、后刀面磨损、沟槽磨损和刀具破损。其中沟槽磨损最为显著,是刀具失效的主要原因。沟槽磨损的产生原因主要有粘结磨损、扩散磨损和塑性侧流产生的切屑毛刺划擦作用,其中粘结磨损为磨损前期的主要原因,而扩散磨损是磨损后期的主要原因。     

An Investigation of the Wear Mechanisms of Polycrystalline Cubic Boron Nitride (PCBN) Tools when End Milling Hardened Steels at Low/Medium Cutting Speeds

The commercial availability of PCBN tools has created the possibility for great improvements in the area of machining hardened steels. Roughing and finishing cuts can be carried out to achieve a surface finish as good as that obtained by grinding. Through this procedure, fabrication time can be greatly reduced and quality increased. This work presents a study of the wear of PCBN and cemented carbide tools when end milling hardened steels at low/medium cutting speeds. The experiments were carried out using a 12.0 mm diameter end milling tool with an indexable insert tipped with PCBN. Removal rate was 384 mm 3 min −1 . Carbide inserts were also tested under the same cutting conditions. The tests were carried out in the dry condition. Three different hardened steels were cut and the wear mechanism was investigated using a scanning electronic microscope (SEM). The minimal wear mechanism found was a combination of adhesion and abrasion. The wear occurred predominantly on the flank face, although some indications of crater wear were also detected. The amount of wear was significantly smaller for PCBN tools than for cemented carbide tools.     

陶瓷涂层刀具切削灰铸铁的试验研究

为了探究陶瓷涂层刀具涂层材质、基体材质对切削性能的影响,试验采用四种陶瓷涂层刀具连续干切削灰铸铁,测试了切削力和切削温度的变化情况以及后刀面的磨损量和已加工表面的粗糙度。结果表明,在刀具基体同为Si_3N_4的条件下,涂层材质为Ti N/Al_2O_3/Ti C的刀具比Ti N/Al_2O_3的切削性能好;在涂层材质同为Ti N的条件下,刀具基体Al_2O_3/Ti CN比Al_2O_3/Ti C的切削性能好。研究发现:四种陶瓷涂层刀具前刀面磨损形式均为微崩刃和月牙洼,后刀面磨损形式均为磨粒磨损和粘着磨损,涂层的磨损形式均为剥落和扩散磨损。     

PCBN刀具负倒棱宽度对磨损的影响分析

使用聚晶立方氮化硼(PCBN)刀具车削V571材质粉末冶金气门座圈,研究负倒棱宽度对刀具磨损的影响规律。采用单因素试验法,在不同PCBN刀具负倒棱宽度下进行切削。结果表明,负倒棱宽度为0.10mm的PCBN刀具有更小的磨损和更长的刀具耐用度。     

硬质合金刀具高速车铣和铣削TC4钛合金磨损试验对比

采用H13A未涂层硬质合金刀具对TC4钛合金进行高速正交车铣和铣削试验,并从刀具磨损破损形态、磨损机理及其寿命等方面进行对比分析。研究表明:高速正交车铣和铣削钛合金时,前、后刀面主要以粘结磨损为主,车铣加工时在切削刃口易形成积屑瘤及连续切屑,但对刀具材料粘结较轻;高速铣削时,对刀具材料粘接较重,在前刀面刃口附近形成凹坑及崩刃;后刀面最大磨损的位置不相同。试验对比了相同切削条件时刀具使用寿命,结果表明采用正交车铣加工可以获得更长的刀具使用寿命。     

Tool wear and its effect on surface roughness in diamond cutting of glass soda-lime

For the technology of diamond cutting of optical glass, the high tool wear rate is a main reason for hindering the practical application of this technology. Many researches on diamond tool wear in glass cutting rest on wear phenomenon describing simply without analyzing the genesis of wear phenomenon and interpreting the formation process of tool wear in mechanics. For in depth understanding of the tool wear and its effect on surface roughness in diamond cutting of glass, experiments of diamond turning with cutting distance increasing gradually are carried out on soda-lime glass. The wear morphology of rake face and flank face, the corresponding surface features of workpiece and the surface roughness, and the material compositions of flank wear area are detected. Experimental results indicate that the flank wear is predominant in diamond cutting glass and the flank wear land is characterized by micro-grooves, some smooth crater on the rake face is also seen. The surface roughness begins to increase rapidly, when the cutting mode changes from ductile to brittle for the aggravation of tool wear with the cutting distance over 150 m. The main mechanisms of inducing tool wear in diamond cutting of glass are diffusion, mechanical friction, thermo-chemical action and abrasive wear. The proposed research makes analysis and research from wear mechanism on the tool wear and its effect on surface roughness in diamond cutting of glass, and provides theoretical basis for minimizing the tool wear in diamond cutting brittle materials, such as optical glass.     

高速干切削铁基粉末冶金零件时细晶粒硬质合金刀具的切削性能研究

用细晶粒硬质合金刀具进行了铁基粉末冶金零件的高速干切削试验。研究了切削参数与刀具耐用度以及加工表面粗糙度的关系,给出了刀具的主要磨损形态,通过能谱分析研究了刀具的磨损机理。结果表明:所选用细晶粒硬质合金刀具具有较高的刀具耐用度和较好的加工表面粗糙度,适合于铁基粉末冶金的加工;细晶粒硬质合金的主要磨损形态是前刀面的月牙洼磨损;主要磨损机理是扩散磨损、粘结磨损。     

纯钒车削刀具磨损表面形态及机理研究

对金刚石刀具、涂层刀具及硬质合金刀具车削纯钒时刀具磨损形态及其磨损机理进行观察和分析.结果表明,在所选取条件下,不同刀具材料对工件材料切削时表现出的刀具磨损形态主要为前刀面磨损、后刀面磨损、微崩刃、剥落和粘结等.刀具的前刀面主要是沿切屑流出方向的沟槽形月牙洼磨损,而后刀面以粘结磨损为主.CD10刀具和H10非涂层刀具具有较佳的切削性能,而H13A非涂层刀具和GC1025涂层刀具不适于纯钒车削.     

The effects of progressive tool wear and tool restricted contact on chip breakability in machining

Chip breakability plays an essential role in automated machining systems. This paper presents an experimental investigation of the effects of progressive tool wear and the resulting formation of the tool restricted contact on chip breakability in a turning operation. Six parameters of tool wear, namely, major flank wear (VB), crater wear depth (KT), crater wear length (KK), crater wear width (KB), wear retract of cutting edge (KS) and nose wear (N), are shown to contribute to the variations of chip breakability with tool wear progression. The results show that the chip breakability varies significantly with tool wear progression, especially with the combined crater and flank wear progression, and contributes to the development of a restricted rake face land, making the tool behave like a restricted contact grooved tool. The chip curling and breaking action is largely influenced by the nature and magnitude of the restricted contact and the groove profile being developed on the tool face. The results presented in this paper are also intended to provide guidelines for designing effective chip grooves on the tool face.