Determination of citrate in tablets and of oxytetracycline in serum using europium (III) luminescence

A direct method for the determination of citrate and oxytetracycline in samples containing complex matrices like tablets or serum has been developed using the luminescence of the ternary complex formed with Eu(III) ions. The triplet-state energy level of oxytetracycline (OxTc), the excitation maximum (412 nm) and the luminescence lifetime of Eu-OxTc (58 μs) were determined. A 17-fold luminescence enhancement at 615 nm occurs upon addition of citrate within a short 5-min incubation time at neutral pH. This is accompanied by a threefold increase of the luminescence decay time. The optimal conditions for determination of OxTc are equal concentrations of Eu (III) and citrate (C = 1 · 10^− 4 mol L^− 1) and pH 7.2. For determination of citrate, the optimal concentrations of Eu(III) and OxTc are 1 : 0.5 (C_Eu = 1 · 10^− 4 mol L^− 1, C_OxTc = 5 · 10^− 5 mol L^− 1) at pH 7.2. The linear range for determination of OxTc in serum is 0.25-250 μg mL^− 1, and for citrate in tablets from 0.5 to 10.0 μg mL^− 1 (2.3 · 10^− 6- 4 · 10^− 5 mol L^− 1). The detection limit was 0.1 μg mL^− 1 for OxTc and 0.2 μg mL^− 1 (1 · 10^-6 mol L^− 1) for citrate, respectively. A comparison of the new method with other methods for determination of citrate is given.     

A single sorbent for tetracycline enrichment and subsequent solid-matrix time-resolved luminescence

The aim of this study was to search for a sorbent that could act as an extraction phase and as a support for solid-matrix time-resolved luminescence (SMTRL). Four potential sorbents were investigated for this purpose using tetracycline (TC) as a model analyte. Sorbents prepared from C18 silica gel or calcium cross-linked pectin gel were able to extract TC from dilute solutions. Europium(III)-TC complex adsorbed on the surface of C18 generated the most intense TRL signal when measured at λ_ex = 388 nm and λ_em = 615 nm. This method achieved a 1 ng/ml limit of detection (LOD) with a 100 μl sample solution in a repeated spotting mode. Hyphenation of sorbent extraction and SMTRL was demonstrated using C18. This method is suitable for screening of TC in foods or aqueous solutions and can be extended to other luminescent lanthanide-chelating analytes in physiological or environmental samples.     

胶束增敏荧光光度法测定土霉素的研究

提出了表面活性剂增敏的酸性降解荧光法测定土霉素的新方法。土霉素与浓H2SO4反应,生成强荧光降解物一脱水土霉素,在pH10.0的NH3 NH4Cl缓冲溶液中,CTMAB的存在对脱水土霉素的荧光有较强的增敏和增稳作用,土霉素含量在1.21×10-8mol/L～4.83×10-6mol/L范围内与荧光强度成正比,方法的检出限为6 66×10-9mol/L。应用本法测定片剂中的土霉素,平均回收率为99.6%(n=5)。     

Synthesis, structure and luminescence property of the ternary and quaternary europium complexes with furoic acid

A ternany europium complex with furoic acid (α-FURA) and 1,10-phenanthroline(phen), [Eu(α-FURA)₃phen]H₂O(I) and a quaternary europium furoate complex with 1,10-phenanthroline and nitrate, Eu(α-FURA)₂NO₃phen(II) were synthesized and characterized by X-ray diffraction. The two europium ions in each of the complexes (I) and (II) are held together by four carboxylato groups with the two modes, namely bidentate bridging and tridentate bridging, and each europium ion is further bonded to two nitrogen atoms from 1,10-phenanthroline and one chelated bidentate furoate group for the complex (I) and one chelated nitrato group for the complex (II), making a coordination number of 9. Luminescence spectra observed at 77 K show that the europium ion site in the crystals of the complexes (I) and (II) has low symmetry and lifetimes of the solid complexes (I) and (II) are 1.13 and 1.20 ms, respectively.     

Capillary zone electrophoresis determination of oxytetracycline in pig tissue samples at maximum residue limits

Summary The determination of the antibiotic oxytetracycline (OTC), in pig tissues was investigated by capillary zone electrophoresis (CZE) with a prior solid-phase extraction (SPE) using alkyl-bonded silica and polymeric cartridges. The methodology developed allows determination of OTC in pig kidney, liver and muscle samples with detection limits below maximum residue limit values, and the procedures to extract OTC and clean-up the matrix are simple and reliable. The limit of detection for OTC was 160, 120 and 85 μg kg⁻¹ for kidney, liver and muscle samples, respectively. The average recoveries from spiked samples (200 μg kg⁻¹ and 1600 μg kg⁻¹) were in excess of 63% with coefficients of variation between 2.0 and 9.8%. This method would be useful for routine monitoring of oxytetracycline residues in pig tissues.     

Measurement and characterization of singlet oxygen production in copper ion-catalyzed aerobic oxidation of ascorbic acid

Production of singlet molecular oxygen (¹O₂) in the aerobic oxidation of ascorbic acid catalyzed by copper ion was measured and characterized using [4′-(9-anthryl)-2,2′:6′,2″-terpyridine-6,6″-diyl]bis(methylenenitrilo)tetrakis(acetate)-Eu³⁺ (ATTA-Eu³⁺) as a highly sensitive and selective time-resolved luminescence probe for ¹O₂. The ¹O₂ produced in the reaction was further characterized and confirmed by (i) chemical trapping of ¹O₂ with 9,10-diphenylanthracene (DPA), the corresponding endoperoxide was detected by HPLC and (ii) spin trapping of ¹O₂ with 2,2,6,6-tetramethyl-4-piperidinol (TMP-OH), the corresponding free radical of TMP-OH oxide (TMPO) was detected by electron spin resonance (ESR) spectroscopy. The effects of deuterium oxide, sodium azide and histidine on the ¹O₂ signal were investigated. The mechanism investigation of ¹O₂ production implied that the ascorbic acid-Cu(I) complex formed in the reaction could be an important intermediate for the ¹O₂ production. The reaction of ascorbic acid with copper ion monitored by ¹H NMR and absorption spectroscopy demonstrated the formation of a copper ion-ascorbic acid complex. Except for Cu²⁺ and Cu⁺-ascorbic acid systems, no detectable ¹O₂ was produced in other transition metal cation-ascorbic acid systems in the studied range.     

Immunochemical determination of oxytetracycline in fish: Comparison between enzymatic and time-resolved fluorometric assays

An indirect competitive enzyme-linked immunosorbent assay (ELISA) with photometric detection of horseradish peroxidase (HRP) activity, was developed in plate to detect oxytetracycline (OTC) in Gilthead sea bream (Sparus aurata) samples. The results were compared to those obtained by time-resolved fluoroimmunoassay (TR-FIA) using a secondary antibody with coproporphyrin of platinum (II) (PtCP) as marker. The limits of detection obtained in fish extract were 16 and 0.08 μg kg⁻¹ for photometric and fluorometric detections, respectively; therefore, they were suitable for fish quality control according to the maximum residue level established by the European Union.An extraction procedure using methanol:water 70:30 (v/v) + 1 mL EDTA 0.1 M, and different clean-up procedures based on solid-phase extraction (C₁₈, polymeric reversed phase, SCX, Si) was assayed. The matrix effects were overcome by means of an average tetracycline-free fish extract calibration curve used for quantification.The OTC optimized ELISA can also be applied to determine tetracycline and chlortetracycline residues with good results. Thus, the developed immunoassay could be considered as a generic assay for the most used tetracyclines in aquaculture antibiotic treatments.In order to confirm the utility of the developed immunoassay as a semi-quantitative methodology, fish samples obtained from different supermarkets were analyzed. Results correlate well with those obtained with a reference HPLC method.     

Development and validation of an improved liquid chromatographic method for the analysis of oxytetracycline

Summary An improved LC method is described for the separation of oxytetracycline and its impurities. The separation is much better than that obtained with official pharmacopoeia methods. The method uses XTerra RP-18, 5 μm (25cm×4.6 mm I.D.), a silica-based stationary phase with methyl end-capping, claimed to reduce silanol activity. The column temperature is set at 30°C and a UV detection is performed at 280 nm. Mobile phase containing acetonitrile −0.25 M tetrabutylammonium hydrogen sulfate pH 7.5−0.25 M ethylenediaminetetraacetic acid pH 7.5-water (115:360:160:365,v/v/v/v) is used at a flow rate of 1.0 mL.min⁻¹, to separate the impurities present in oxytetracycline base. A central composite experimental design is used to optimize the separation. A second isocratic method with higher content of acetonitrile is needed to separate the more retained impurities present only in oxytetracycline hydrochloride. The method is robust and shows good selectivity, repeatability, linearity and sensitivity.     

New insight in the structure–luminescence relationships of Ca9Eu(PO4)7

The double phosphate Ca₉Eu(PO₄)₇, obtained by solid state reaction, was found to be isotypic with Ca₃(PO₄)₂, with space group R3c and unit cell parameters a=10.4546(1) Å, c=37.4050(3) Å, V=3540.67(9) Å³, Z=6. The structure parameters refined using the Rietveld method showed that europium shares positions M1, M2 and M3 with calcium, contradicting previously published Mössbauer results. Low temperature luminescence under selective excitation of Eu³⁺ in Ca₉Y_1−xEu_x(PO₄)₇ and in Ca₉Eu(PO₄)₇ samples was studied, confirming the Eu³⁺ distribution into these sites. At 10 K, ⁵D₀→⁷F₀ emission lines of Eu³⁺ were observed at 578.5, 579.5, 580.1 nm for the M3, M1 and M2 sites, respectively. High temperature X-ray powder diffraction evidenced a second-order phase transition around 573 °C.     

Luminescence determination of europium microquantities after its preconcentration on polyurethane foam

Sorption of the mixed-ligand complexes of europium(III) with thenoyltrifluoroacetone (TTA) and 1,10-phenanthroline (Phen) on polyurethane foam (PUF) has been studied by a luminescence method. The optimum conditions of sorption have been found. The sorbate composition on PUF has been determined (the Eu:TTA:Phen ratio was 1:3:1). Luminescence spectra of the europium complexes in solution and on PUF at 77 K have been investigated. It was concluded that the character of the Eu³⁺ coordination both in solution and on the sorbent is the same. Stability constants for the complexes in solution (lg K = 8.4) and on the sorbent (lg K = 5.5) have been calculated. The decrease of the stability of the complex on PUF is explained by the deformation of the complex molecule in the sorbent phase. Sorption coefficients for europium (245) and scandium (2.35) and the coefficient of selectivity for europium in Sc₂O₃ (102.3) have been determined. A method for the sorption-luminescence determination of europium in Sc₂O₃ with a lower limit of contents determined of 1 × 10⁻⁶⁰% has been developed.     

Synthesis,crystal structure and luminescence of three europium complexes with 2-iodobenzoic acid

Three new complexes, [Eu(2-IBA)₃?·?H₂O] _n (1), [Eu(2-IBA)₃?·?2,2′-bpy]₂ (2), and [Eu(2-IBA)₃?·phen]₂ (3) (2-IBA?=?2-iodobenzoato; 2,2′-bpy?=?2,2’-bipyridine; phen?=?1,10-phenanthroline) were synthesized, and their crystal structures determined by X-ray diffraction. In complex 1, Eu³⁺ ions are linked through carboxylate groups via bridging – chelating – bridging coordination modes to form a one-dimensional polymeric chain. The carboxylate groups are tetradentate-bridged. Complex 2 is binuclear with an inversion center, in which europium is nine-coordinated with seven oxygen atoms from five 2-IBA ligands and two nitrogen atoms from one 2,2′-bpy molecule in a distorted monocapped square antiprism. The crystal structure of 3 is similar to that of 2. These complexes emit red light luminescence. The ⁵ D ₀?→?⁷ F _j (j?=?1–4) transition emission of Eu³⁺ ion has been observed.     

Highly efficient and selective turn-off quenching of ligand-sensitized luminescence from europium imidazo[4,5-f]-1,10-phenanthroline complex by fluoride ion

A smart fluoride sensitive luminescence probe based on 1:2 complex of europium(III) with 2-(2-hydroxyphenyl)imidazo[4,5-f]-1,10-phenanthroline was prepared. The emission of europium ions via photosensitization of the ligand was completely quenched by addition of 2 equiv. of fluoride ions in DMSO. Spectroscopic analyses proved that the imidazolyl NH of the ligand was hydrogen-bonded with additive fluoride to form the 1:1 complex, leading to suppression of the photosensitization.     

High-performance liquid chromatographic determination/identification of oxytetracycline and sulphadimidine in meat and eggs

Summary A rapid method for the simultaneous determination/identification of residual oxytetracycline (OTC) and sulphadimidine (SDD) in meats (beef, pork, chicken) and eggs by high-performance liquid chromatography (HPLC) was developed. The extraction of OTC and SDD was performed using a Sep-Pak^? CN cartridge. The extracts contained OTC/SDD analytes when examined by HPLC using a LiChrospher^? 100 RP-8 end-capped column and a mobile phase of acetonitrile-acetic acid-water (28:4:68, v/v/v) with a photodiode array detector. The average recoveries from spiked samples (0.1 μg g⁻¹ and 1.0 μg g⁻¹) were in excess of 80.2% with coefficients of variation between 1.5 and 5.0%. The limits of detection for OTC and SDD were 0.05 and 0.02 μg g⁻¹, respectively.     

Time-resolved enzymatic determination of glucose using a fluorescent europium probe for hydrogen peroxide

An enzymatic assay for glucose based on the use of the fluorescent probe for hydrogen peroxide, europium(III) tetracycline (EuTc), is described. The weakly fluorescent EuTc and enzymatically generated H₂O₂ form a strongly fluorescent complex (EuTc–H₂O₂) whose fluorescence decay profile is significantly different. Since the decay time of EuTc–H₂O₂ is in the microseconds time domain, fluorescence can be detected in the time-resolved mode, thus enabling substantial reduction of background fluorescence. The scheme represents the first H₂O₂-based time-resolved fluorescence assay for glucose not requiring the presence of a peroxidase. The time-resolved assay (with a delay time of 60 s and using endpoint detection) enables glucose to be determined at levels as low as 2.2 mol L^–1, with a dynamic range of 2.2–100 mol L^–1. The method also was adapted to a kinetic assay in order to cover higher glucose levels (mmol L^–1 range). The latter was validated by analyzing spiked serum samples and gave a good linear relationship for glucose levels from 2.5 to 55.5 mmol L^–1. Noteworthy features of the assay include easy accessibility of the probe, large Stokes shift, a line-like fluorescence peaking at 616 nm, stability towards oxygen, a working pH of approximately 7, and its suitability for both kinetic and endpoint determination.     

Application of time-resolved luminescence to dry reagent chemical technology

A time-resolved luminescence method describing the use of terbium(III) in the dry reagent format is presented for the first time. Paper strips previously treated with sucrose are used as solid substrates where terbium(III) is immobilised by adsorption. The strips are stable for at least 6 months and they can be easily stored under a desiccant medium. Only the addition of the buffered sample is required for the analysis. This methodology has been applied to the determination of two local anaesthetics, namely benzocaine and procaine. These compounds release p-aminobenzoic acid after a hydrolysis step in alkaline medium, which reacts to terbium(III) giving a luminescent chelate. The luminescence intensity measurements are obtained at λ_ex 286 and λ_em 545 nm by using the time-resolved mode of the instrument. The method presents a linear range from 1.1 to 21.9 μM and the calculated LOD is 0.4 μM. It has been satisfactorily applied to the analysis of pharmaceutical samples and the recoveries obtained are in the range 88-108%.     

Integrated X-ray crystallography, optical and computational methods in studies of structure and luminescence of new synthesized complexes of lanthanides with ligands derived from 2,6-diformylpyridine

The reaction of 2,6-diformylpyridine-bis(benzoylhydrazone) [dfpbbh] and 2,6-diformylpyridine-bis(4-phenylsemicarbazone) [dfpbpsc] with lanthanides salts yielded the new chelates complexes [Eu(dfpbpsc-H⁺)₂]NO₃ (1), [Dy(fbhmp)₂][Dy(dfpbbh-2H⁺)₂]·2EtOH·2H₂O (fbhmp = 2-formylbenzoylhydrazone-6-methoxide-pyridine; Ph = phenyl; Py = pyridine; Et = ethyl) and [Er₂(dfpbbh-2H⁺)₂(μ-NO₃)(H₂O)₂(OH)]·H₂O.X-ray diffraction analysis was employed for the structural characterization of the three chelate complexes. In the case of complex 1, optical, synthetic and computational methods were also exploited for ground state structure determinations and triplet energy level of the ligand and HOMO-LUMO calculations, as well as for a detailed study of its luminescence properties.     

稀土配合物的时间分辨光谱分析法研究(Ⅰ)TFA-TOPO-农乳-100体系用于测定铕和钐

本文采用自己组装的时间分辨荧光光谱测定装置,研究了铕(钐)-三氟乙酰丙酮-三正辛基膦化氧(Eu(Sm)-TFA-TOPO)在非离子表面活性剂农乳-100存在下的光谱特性、荧光衰减动力学特性和发光机理。提出了能量传递机制和第二配体TOPO在荧光发射过程中的作用,制定出TFA-TOPO-农乳-100体系测定痕量铕和钐的时间分辨荧光光谱分析方法,用于测定高纯氧化钇中的痕量铕和钐,结果令人满意。     

Designing of luminescent GdPO4:Eu@LaPO4@SiO2 core/shell nanorods: Synthesis,structural and luminescence properties

GdPO₄:Eu³⁺ (core) and GdPO₄:Eu@LaPO₄ (core/shell) nanorods (NRs) were successfully prepared by urea based co-precipitation process at ambient conditions which was followed by coating with amorphous silica shell via the sol-gel chemical route. The role of surface coating on the crystal structure, crystallinity, morphology, solubility, surface chemistry and luminescence properties were well investigated by means of X-ray diffraction (XRD), transmission electron microscopy (TEM), energy dispersive X-ray (EDX) analysis, Fourier Transform Infrared (FTIR), UV-Vis, and photoluminescence spectroscopy. XRD pattern revealed highly purified, well-crystalline, single phase-hexagonal-rhabdophane structure of GdPO₄ crystal. The TEM micrographs exhibited highly crystalline and narrow size distributed rod-shaped GdPO₄:Eu³⁺ nanostructures with average width 14–16 nm and typical length 190–220 nm. FTIR spectra revealed characteristic infrared absorption bands of amorphous silica. High absorbance in a visible region of silica modified core/shell/Si NRs in aqueous environment suggests the high solubility along with colloidal stability. The photoluminescence properties were remarkably enhanced after growth of undoped LaPO₄ layers due to the reduction of nonradiative transition rate. The advantages of presented high emission intensity and high solubility of core/shell and core/shell/Si NRs indicated the potential applications in monitoring biological events.     

Development of a ratiometric time-resolved luminescence sensor for pH based on lanthanide complexes

Time-resolved luminescence bioassay technique using lanthanide complexes as luminescent probes/sensors has shown great utilities in clinical diagnostics and biotechnology discoveries. In this work, a novel terpyridine polyacid derivative that can form highly stable complexes with lanthanide ions in aqueous media, (4′-hydroxy-2,2′:6′,2′′-terpyridine-6,6′′-diyl) bis(methylenenitrilo) tetrakis(acetic acid) (HTTA), was designed and synthesized for developing time-resolved luminescence pH sensors based on its Eu³⁺ and Tb³⁺ complexes. The luminescence characterization results reveal that the luminescence intensity of HTTA–Eu³⁺ is strongly dependent on the pH values in weakly acidic to neutral media (pK_a = 5.8, pH 4.8–7.5), while that of HTTA–Tb³⁺ is pH-independent. This unique luminescence response allows the mixture of HTTA–Eu³⁺ and HTTA–Tb³⁺ (the HTTA–Eu³⁺/Tb³⁺ mixture) to be used as a ratiometric luminescence sensor for the time-resolved luminescence detection of pH with the intensity ratio of its Tb³⁺ emission at 540 nm to its Eu³⁺ emission at 610 nm, I_540 nm/I_610 nm, as a signal. Moreover, the UV absorption spectrum changes of the HTTA–Eu³⁺/Tb³⁺ mixture at different pHs (pH 4.0–7.0) also display a ratiometric response to the pH changes with the ratio of absorbance at 290 nm to that at 325 nm, A_290 nm/A_325 nm, as a signal. This feature enables the HTTA–Eu³⁺/Tb³⁺ mixture to have an additional function for the pH detection with the absorption spectrometry technique. For loading the complexes into the living cells, the acetoxymethyl ester of HTTA was synthesized and used for loading HTTA–Eu³⁺ and HTTA–Tb³⁺ into the cultured HeLa cells. The luminescence imaging results demonstrated the practical utility of the new sensor for the time-resolved luminescence cell imaging application.