Bioactivity potential of calcium alumino-silicate glasses and glass–ceramics containing nitrogen and fluorine

Calcium alumino-silicate glasses of general composition (in eq.%) 28Ca:57Si:15Al:[100 ? (x + y)]O:xN:yF (x = 0 or 20 and y = 0, 3 or 5) and their glass–ceramic counterparts were immersed in simulated body fluid (SBF) at 37 ± 0.5 °C for 28 days to assess their potential bioactivity. The glasses showed no Ca release or surface calcium phosphate deposition due to their high network connectivities (>2.55). The glass–ceramics all showed potential bioactivity, as the SBF became enriched in Ca and calcium phosphate deposits formed on their surfaces. This was a result of Ca release from crystalline phases (predominantly wollastonite in the case of CaSiAlOF glass–ceramics and gehlenite in the case of CaSiAlONF glass–ceramics). No aluminium was leached from the glass–ceramics into the SBF, due to its pH always exceeding 7.0.     

The effect of investment materials on the surface of cast fluorcanasite glasses and glass–ceramics

Modified fluorcanasite glass–ceramics were produced by controlled two stage heat-treatment of as-cast glasses. Castability was determined using a spiral castability test and the lost-wax method. Specimens were cast into moulds formed from gypsum and phosphate bonded investments to observe their effect on the casting process, surface roughness, surface composition and biocompatibility. Both gypsum and phosphate bonded investments could be successfully used for the lost-wax casting of fluorcanasite glasses. Although the stoichiometric glass composition had the highest castability, all modified compositions showed good relative castability. X-ray diffraction showed similar bulk crystallisation for each glass, irrespective of the investment material. However, differences in surface crystallisation were detected when different investment materials were used. Gypsum bonded investment discs showed slightly improved in vitro biocompatibility than equivalent phosphate bonded investment discs under the conditions used.     

Photoluminescence and scintillation properties of Eu2O3–BaO–Nb2O5–TeO2 glass and glass ceramics

Journal of Materials Science: Materials in Electronics - 1Eu2O3–3BaO–20Nb2O5–76TeO2 glass and the corresponding glass-ceramics were synthesized with the aim to investigate the...     

Effects of glass components on crystallization and dielectric properties of BST glass–ceramics

Crystallization behavior was studied for glass powders in which some portions of AlF₃ in the net composition of 60(Ba_0.7Sr_0.3)TiO₃–25SiO₂–15AlF₃ were replaced with Ga₂O₃ or Bi₂O₃. The replacement with Ga₂O₃ resulted in a progressive increase in crystallization temperature, which effectively assisted the viscous sintering of glass powders to produce densified BST glass–ceramics at relatively lower temperatures. For the Bi₂O₃-replaced glass powders, an increasing amount of Bi₂O₃ replacement lowered the crystallization temperature and yielded less densified glass–ceramics containing a considerable amount of glassy phase. The temperature dependence of permittivity was estimated for the Ga₂O₃- and Bi₂O₃-replaced glass–ceramics as a function of sintering conditions and the amount of replacement, respectively.     

Effects of MgO on properties of Li2O–Al2O3–SiO2 glass–ceramics for LTCC applications

Li₂O–Al₂O₃–SiO₂ (LAS) glass–ceramics for low temperature co-fired ceramics (LTCC) application were prepared by melting method, and the effects of MgO on the sinterability, microstructure, dielectric property, thermal expansion coefficient (CTE) and mechanical character of this glass–ceramics have been studied. The X-ray diffraction images represent that the main phase is β-spodumene solid solutions. And some ZrO₂ and CaMgSi₂O₆ phases in LAS glass–ceramics are detected. The LAS glass–ceramics without additive (MgO) sintered at 800° had the dielectric properties: dielectric constant (ε_r) of 5.3, dielectric loss (tanδ) of 2.97 × 10^?3 at 1 MHz, CTE value of 1.06 × 10^?6 K^?1, bulk density of 2.17 g/cm³, and flexural strength of 73 MPa. 5.5 wt% MgO-added LAS glass–ceramic achieves densification at 800° exhibited excellent properties: low dielectric constant and loss (ε_r = 7.1, tanδ = 2.02 × 10^?3 at 1 MHz), low CTE (2.89 × 10^?6 K^?1), bulk density = 2.65 g/cm³ as well as high flexural strength (145 MPa). The results indicate that the addition of MgO is helpful to improve the dielectric and mechanical properties. The formation of CaMgSi₂O₆ crystal phase with higher CTE leads to the increase of CTE value of LAS glass–ceramics due to the increasing MgO content, and the increase of CTE is favourable for matching with silicon (3.1 × 10^?6 K^?1). The prepared LAS glass–ceramics have the potential for LTCC application.     

B-Phase solid solutions in Er- and Y-SiAlON glass–ceramics

Glasses with cation composition of M:Si:Al = 3.45:3:2 (where M = Er and Y) with varying nitrogen contents (0, 5, 8, 15 and 22 eq.%) have been prepared by ball milling in alcohol media. These Er- and Y-sialon glasses were heat-treated at temperatures in the range of 950–1200 °C for 10 h to study the crystal phase(s) obtained. Samples were characterised by SEM and XRD and obtained data from XRD were further analysed to obtain unit cell parameters of some phases. It is shown that it is possible to obtain B-phase (Y₂SiAlO₅N) from these glass compositions with relatively low nitrogen contents (5 and 8 eq.%N) but with different unit cell parameters (i.e. a = 3.77–3.81 Å and c = 9.83–9.97 Å) to those reported previously in the literature, suggesting that there are some compositional differences between B-phases obtained from different nitrogen content glasses as well as different modifier cations. Long-term heat treatment studies revealed that the stability range of temperature for Er–B-phase is more extensive than its Y–B-phase equivalent.     

Spectroscopic properties of Eu3+/Nd3+ co-doped phosphate glasses and opaque glass–ceramics

This paper reports the fabrication and characterization of Eu³⁺/Nd³⁺ co-doped phosphate (PNE) glasses and glass–ceramics as a function of Eu³⁺ concentration. The precursor glasses were prepared by the conventional melt quenching technique and the opaque glass–ceramics were obtained by heating the precursor glasses at 450 °C for 30 h. The structural and optical properties of the glass and glass–ceramics were analyzed by means of X-ray diffraction, Raman spectroscopy, UV–VIS–IR absorption spectroscopy, photoluminescence spectra and lifetimes. The amorphous and crystalline structures of the precursor glass and opaque glass–ceramic were confirmed by X-ray diffraction respectively. The Raman spectra showed that the maximum phonon energy decreased from 1317 cm⁻¹ to 1277 cm⁻¹ with the thermal treatment. The luminescence spectra of the glass and glass–ceramic samples were studied under 396 nm and 806 nm excitation. The emission intensity of the bands observed in opaque glass–ceramic is stronger than that of the precursor glass. The luminescence spectra show strong dependence on the Eu³⁺ ion concentration in the Nd³⁺ ion photoluminescence (PL) intensity, which suggest the presence of energy transfer (ET) and cross-relaxation (CR) processes. The lifetimes of the ⁴F_3/2 state of Nd³⁺ ion in Eu³⁺/Nd³⁺ co-doped phosphate glasses and glass–ceramics under 806 nm excitation were measured. It was observed that the lifetimes of the ⁴F_3/2 level of Nd³⁺ of both glasses and glass–ceramics decrease with the increasing Eu³⁺ concentration. However in the case of opaque glass–ceramics the lifetimes decrease only 16%.     

Characterization of SiO2–Na2O–Fe2O 3–CaO–P2O 5–B 2O 3 glass ceramics

Bioactivity and magnetic properties were investigated in glass and glass ceramics based on the SiO₂–Na₂O–Fe₂O₃–CaO–P₂O₅–B₂O₃ system to find their suitability as thermoseed for hyperthermia treatment of cancer. The effect of change in compositions on bioactivity was examined in simulated body fluids. The glass ceramic samples exhibit Na₃CaSi₃O₈ and Na_3-XFe_XPO₄ phases. After dipping the glass ceramic samples in simulated body fluids silica hydrogel first forms, followed by an amorphous calcium phosphate layer. Magnetic and microwave resonance experiments further demonstrate the potential of these glass ceramics for possible use in hyperthermia.     

Synthesis and characterization of barium borosilicate glass–Al2O3 composites

Barium borosilicate glass with composition 30BaO–60B₂O₃–10SiO₂ glass was prepared by melt-quenching technique. Different weight % of crystalline Al₂O₃ was mixed with the glass powder and sintered at optimum temperature. The changes in the structure and thermal properties of the glass with alumina content were investigated by X-ray powder diffraction, FT-IR spectroscopy and differential thermal analysis. The variations in the coefficient of thermal expansion and dielectric properties with composition were also studied and correlated with the structural changes.     

Selection of eutectic systems in Al2O3–Y2O3 ceramics

There are two eutectic reactions in the Al₂O₃-rich portion of the Al₂O₃–Y₂O₃ pseudo-binary system; one is the equilibrium Al₂O₃–YAG eutectic reaction at 1826°C, and the other is the metastable Al₂O₃–YAP eutectic reaction at 1702°C. Selection of the Al₂O₃–YAG and the Al₂O₃–YAP eutectics was examined in terms of cooling rate, nucleation temperature and maximum melt temperature. When the melt was cooled from 2100°C at any cooling rate, it always nucleated below the Al₂O₃–YAP eutectic temperature, therefore the Al₂O₃–YAP eutectic was selected. The Al₂O₃–YAG eutectic was selected when the melt was cooled from 1900°C at a cooling rate of less than 1 K s⁻¹. The selection of the two eutectic systems was determined by the nucleation temperature, although the maximum holding temperature of the melt and the cooling rate significantly affected the nucleation temperature. The structure of the melt, such as coordination of oxygen and chemical order when being heated to 2100°C may affect the nucleation behavior.     

Microstructure and microwave dielectric characteristics of CaO–B2O3–SiO2 glass ceramics

CaO–B₂O₃–SiO₂ (CBS) glass powders are prepared by traditional glass melting method, whose properties and microstructures are characterized by Differential thermal analysis (DTA), X-ray diffraction (XRD) and scanning electron microscopy (SEM). It is found that the pure CBS glass ceramics possess excellent dielectric properties (ε _r = 6.5, tan δ = 5 × 10⁻³ at 10 GHz), but a higher sintering temperature (>900 °C) and a narrow sintering temperature range (about 10 °C). The addition of a low-melting-point CaO–B₂O₃–SiO₂ glass (LG) could greatly decrease the sintering temperature of CBS glass to 820 °C and significantly enlarge the sintering temperature range to 40 °C. The CBS glass ceramic with 30 wt% LG glass addition sintered at 840 °C exhibits better dielectric properties: ε _r ≈ 6, tan δ < 2 × 10⁻³ at 10 GHz, and the major phases of the sample are CaSiO₃, CaB₂O₄ and SiO₂.     

Study of linear and non-linear optical properties of In–Se doped chalcogenide semiconducting glasses

Journal of Materials Science: Materials in Electronics - The present work focuses on the various linear and non-linear optical properties of antimony (Sb) and gallium (Ga) (both 0.1 at.%) doped...     

Bioactivity and cytotoxicity of glass and glass–ceramics based on the 3CaO·P2O5–SiO2–MgO system

The mechanical strength of bioactive glasses can be improved by controlled crystallization, turning its use as bulk bone implants viable. However, crystallization may affect the bioactivity of the material. The aim of this study was to develop glass–ceramics of the nominal composition (wt%) 52.75(3CaO·P₂O₅)–30SiO₂–17.25MgO, with different crystallized fractions and to evaluate their in vitro cytotoxicity and bioactivity. Specimens were heat-treated at 700, 775 and 975 °C, for 4 h. The major crystalline phase identified was whitlockite, an Mg-substituted tricalcium phosphate. The evaluation of the cytotoxicity was carried out by the neutral red uptake methodology. Ionic exchanges with the simulated body fluid SBF-K9 acellular solution during the in vitro bioactivity tests highlight the differences in terms of chemical reactivity between the glass and the glass–ceramics. The effect of crystallinity on the rates of hydroxycarbonate apatite (HCA) formation was followed by Fourier transformed infrared spectroscopy. Although all glass–ceramics can be considered bioactive, the glass–ceramic heat-treated at 775 °C (V775-4) presented the most interesting result, because the onset for HCA formation is at about 24 h and after 7 days the HCA layer dominates completely the spectrum. This occurs probably due to the presence of the whitlockite phase (3(Ca,Mg)O·P₂O₅). All samples were considered not cytotoxic.     

Optical waveguides in electrooptical nanophase glass–ceramics

Optical wave guides in glass–ceramics, demonstrating a high Kerr coefficient, are studied. The waveguides were produced by an ion exchange technique applied to glass–ceramics formed by controllable glass crystallization under heat treatment.     

Sintering, densification and crystallization of Ca–Al–B–Si–O glass/Al2O3 composites for LTCC application

Ca–Al–B–Si–O glass/Al₂O₃ composites were prepared based on the borosilicate glass powders (D₅₀ = 2.84) and Al₂O₃ ceramic powders (D₅₀ = 3.26), and the sintering, densification, crystallization of samples were investigated. The shrinkage of sample starts to have a sharp increase at 600 °C. The shrinkage of sample starts to have a further rapid increase after the glass softening temperature of about 713 °C. Glass/Al₂O₃ composites can be sintered at 875 °C/15 min and exhibit better properties of a relative density of 98.4 %, a λ value of 2.89 W/mK, a ε _r value of 7.82 and a tan δ value of 5.3 × 10^?4. The interface between glass and Al₂O₃ grains and the interface between anorthite and glass phase depicts a good compatibility according to transmission electron microcopy test. It is the low sintering temperature, high density and good compatibility with Ag electrodes that, guarantee borosilicate glass/Al₂O₃ composites suitable for low temperature co-fired ceramic materials.     

Oxidation and abrasive wear of Fe–Si and Fe–Al intermetallic alloys

In the present work, intermetallic alloys Fe–Si and Fe–Al (Fe₃Si–C–Cr and Fe₃Al-C), produced by induction melting, were evaluated regarding their oxidation and abrasive resistance. The tests performed were quasi-isothermal oxidation, cyclic oxidation, and dry sand/rubber wheel abrasion. As reference, the ASTM A297-HH grade stainless steel was tested in the same conditions. In the oxidation tests, the Fe–Al based alloy presented the lowest oxidation rate, and the Fe–Si based alloy achieved the best results in the abrasion test, showing better performance than the HH type stainless steel.