Characterization of high-quality polycrystalline diamond and its high FET performance

We characterized high-quality polycrystalline diamond with large grains and fabricated polycrystalline diamond field effect transistors (FETs). The polycrystalline diamond had (110) preferred orientation, and its typical grain size was  100 μm. Well-resolved free exciton related emissions were observed at room temperature in cathodoluminescence. The FETs showed extremely high DC and RF performance. The cut-off frequency for current gain (f_T) and power gain (f_max) were 45 and 120 GHz, respectively. The maximum drain current (I_DS) was 550 mA/mm. These values are the highest among diamond FETs, including those fabricated from single-crystal diamond. These results suggest that high-quality polycrystalline diamond, whose maximum size is 4 in., is very promising for diamond electronic devices.     

Temporal and spatial Lagrangean decompositions in multi-site, multi-period production planning problems with sequence-dependent changeovers

We address in this paper the optimization of a multi-site, multi-period, and multi-product planning problem with sequence-dependent changeovers, which is modeled as a mixed-integer linear programming (MILP) problem. Industrial instances of this problem require the planning of a number of production and distribution sites over a time span of several months. Temporal and spatial Lagrangean decomposition schemes can be useful for solving these types of large-scale production planning problems. In this paper we present a theoretical result on the relative size of the duality gap of the two decomposition alternatives. We also propose a methodology for exploiting the economic interpretation of the Lagrange multipliers to speed the convergence of numerical algorithms for solving the temporal and spatial Lagrangean duals. The proposed methods are applied to the multi-site multi-period planning problem in order to illustrate their computational effectiveness.     

High spatial resolution photoluminescence and Raman spectroscopic measurements of a natural polycrystalline diamond, carbonado

Photoluminescence and Raman spectra with high spatial resolution (< 1 μm) were observed on a natural polycrystalline diamond, carbonado. The studied sample is from Central African Republic (CAR) and was polished to optical grade. In addition to observation by optical microscopy, Scanning Near-field Optical Microscopy (SNOM) was applied for spectral and topographic analysis at high spatial resolution less than 300 nm. Mapping of the photoluminescence intensity of carbonado using SNOM indicated that the emission intensity was lower at the grain boundaries and the fringe of pores of carbonado revealed weakest intensity. Photoluminescence spectra of carbonado observed using optical microscopy and SNOM comprised three sharp bands at 504, 575 and 638 nm with their side bands and the color of photoluminescence changed according to its location. Raman spectra measured using optical microscopy revealed that the residual stress locally exists underneath the sample surface and the maximum stress value observed in this study was 0.72 GPa. Additionally, pressure dependence of the 575 nm band was measured using a diamond anvil cell up to 3.5 GPa. The 575 nm band shifted linearly to a lower wavelength with increasing pressure with a gradient of − 0.57 GPa/nm. This relationship was applied to estimations of the stress distribution of carbonados using SNOM. No significant changes in peak positions of photoluminescence spectra were detected on the surface of carbonados. This result suggests that carbonado is well sintered and that the residual stress of carbonado exists locally inside the crystal.     

Performance response and recovery of temporal and spatial phase separated process for nutrients removal in short-term shock loadings

This study was conducted to evaluate the stability and performance response under short-term hydraulic and organic shock load conditions in temporal and spatial phase separated process. The overall removals of BOD, TN, and TP declined slightly despite the hydraulic shock loading, and rapid recovery could be observed again after four cycles of 16 h. It seems that rapid recovery may be achieved by the unique characteristics of the system operated in a fed-batch manner. The effect of shock load on nitrogen removal due to increment of flow rate was higher than that of phosphorus, because of the insufficient reaction time for the nitrification and denitrification. After the organic shock, however, recovery time for phosphorus removal was needed rather than that of organics and nitrogen, because the overload to micro organisms related to the phosphorus release is attained by short-term organic shock loading.     

Spatial and temporal scaling of nitrous oxide emissions from the field to the regional scale in Scotland

Nitrous oxide (N₂O) is a powerful greenhouse gas. As the UK government is committed to reducing greenhouse gas emissions, it is important to know not only how much of these gases are released but also where and when. Targeted measurements of emissions in relation to crop growth cycles, soil wetness and fertiliser applications were used to derive annual emission rates for specific combinations of soil type, land management and fertiliser practices. These annual emission rates were then spatially scaled to derive regional figures through the development of a Geographic Information System (GIS) based model framework. Digital soil and land use maps at a scale of 1:25000 for two test areas of approximately 200000 ha each (Lothians and the Ayrshire Basin) were overlain with a climate map within the GIS, deriving unique combinations of soil wetness and land use. The calculated annual emission rates (kg N ha^–1 yr^–1) were then applied to these and multiplied by the total area of each soil/land use type to derive annual emission losses for each area. The annual emission of nitrous oxide from the Lothians was determined as approximately 381000 kg N yr^–1, while the emissions from the Ayrshire Basin were predicted to be 794000 kg N yr^–1. This indicates the increased emissions associated with both the wetter soils of Ayrshire and the greater extent of grazed pasture systems in this area. Due to the detailed scale of the input data, localised areas with large emissions were identified. Abatement strategies would be concentrated on areas of high emissions that include a change to crops with lower emission potential, reducing fertiliser and manure inputs, reducing grazing intensity and improving soil drainage.Supplementary material to this paper is available in electronic form at http://dx.doi.org/10.1023/A:1024422604493     

Flame-ionization detector response to methyl, ethyl, propyl, and butyl esters of fatty acids

The concept of theoretical response factors is not directly applicable to methyl esters of short-chain fatty acids (FA), since their carbon deficiency is larger than expected from theory. Substituting the methyl group by an ethyl, propyl, or butyl group improved the flame-ionization efficiency of fatty acid esters gradually, up to the point where the empirical response factors of the butyl esters were identical within experimental error to the theoretical values. Butyl esters of FA have a uniform flame-ionization detection (FID) response irrespective of the number of carbon atoms contained in the FA. They exhibit a carbon deficiency of 1.0, i.e. the carbonyl carbon atom does not respond, as expected from theory. Compared to methyl esters, which have a carbon deficiency of 1.4–1.5 for short-chain FA, use of butyl esters has the advantage that a precalculation of the FID response enables the analyst to judge whether the analytical system employed works properly and the data produced are accurate and reliable. Both acid (BF₃ or H₂SO₄)-and alkali (butoxide)-catalyzed butyl ester preparation were equally effective, giving the analyst a choice of methods so that different analytical needs can be addressed efficiently. Computing response factors and comparing the theoretically expected values with those obtained experimentally gives the experimenter an indication whether the analytical system employed for FA profiling (transesterification plus the subsequent gasliquid chromatographic separation and quantitation by FID) works properly. This setup is particularly useful for an accurate analysis of the FA profile of milk fat.     

Anodic behavior of sertindole and its voltammetric determination in pharmaceuticals and human serum using glassy carbon and boron-doped diamond electrodes

The electrochemical oxidation of sertindole was investigated using cyclic, linear sweep voltammetry at a glassy carbon and boron-doped diamond electrodes. The aim of this study was to determine sertindole levels in serum and pharmaceutical formulations, by means of electrochemical methods. In cyclic voltammetry, depending on pH values, sertindole showed one or two irreversible oxidation responses. These two responses were found related to the different electroactive part of the molecule. Using second and sharp oxidation peak, two voltammetric methods were described for the determination of sertindole by differential pulse and square wave voltammetry at the glassy carbon and boron-doped diamond electrodes. Under optimized conditions, the current showed a linear dependence with concentration in the range between 1 × 10⁻⁶ and 1 × 10⁻⁴ M in acetate buffer at pH 3.5 and between 4 × 10⁻⁶ and 1 × 10⁻⁴ M in spiked human serum samples for both methods. The repeatability, reproducibility, selectivity, precision and accuracy of all the methods in all media were investigated and calculated. These methods were successfully applied for the analysis of sertindole pharmaceutical dosage forms and human serum samples. No electroactive interferences from the tablet excipients and endogenous substances from biological material were found.     

Growth of faceted, ballas-like and nanocrystalline diamond films deposited in CH4/H2/Ar MPCVD

The influence of Ar addition to CH₄/H₂ plasma on the crystallinity, morphology and growth rate of the diamond films deposited in MPCVD was investigated using scanning electron microscopy (SEM), X-ray diffraction (XRD) and Raman spectroscopy. X-Ray diffraction patterns indicate that diamond films of strong (111) and weak (400) texture are produced in these samples. Faceted diamond gradually turns into ballas-like diamond with graphitic inclusions when the Ar concentration increases to above 30 vol.%, as indicated by Raman spectra. As the Ar concentration goes above 90 vol.%, nanocrystalline diamond films are formed, characterized by a 1150-cm⁻¹ peak in the Raman spectra and morphology observation. Diamond growth by CH₃ or by C₂ mechanism is proposed to interpret the change in the growth rate of diamond films with the variation of Ar content in the plasma.     

Electrochemical oxidation of acid black 210 dye on the boron-doped diamond electrode in the presence of phosphate ions: Effect of current density, pH, and chloride ions

The electrochemical oxidation of acid black 210 dye (AB-210) on the boron-doped diamond (BDD) was investigated under different pH conditions. The best performance for the AB-210 oxidation occurred in alkaline phosphate solution. This is probably due to oxidizing agents such as phosphate radicals and peroxodiphosphate ions, which can be electrochemically produced with good yields on the BDD anode, mainly in alkaline solution. Under this condition, the COD (chemical oxygen demand) removal was higher than that obtained from the model proposed by Comninellis. Electrolyses performed in phosphate buffer and in the presence of chloride ions resulted in faster COD and color removals in acid and neutral solutions, but in alkaline phosphate solution, a better performance in terms of TOC removal was obtained in the absence of chloride. Moreover, organochloride compounds were detected in all electrolyses performed in the presence of chloride. The AB-210 electrooxidation on BDD using phosphate as supporting electrolyte proved to be interesting since oxidizing species generated from phosphate ions were able to completely degrade the dye without producing organochloride compounds.     

Growth response of rubber seedlings to N,P, and K fertilizer in Nigeria

A two-year study (1977/78 and 1978/79) was carried out using GT I seedlings raised in polybags at the Rubber Research Institute of Nigeria (RRIN) main station, to determine the response of rubber seedlings to the application of N, P, K fertilizer. The fertilizers were each applied at three rates as follows: 0, 45 and 90 kg N per ha as sulphate of ammonia; 0, 14.80 and 29.60 kg P per ha as single superphosphate and 0, 9 and 18 kg K per ha as muriate of potash. Stem diameter and height were measured at monthly intervals, while dry matter of tops was estimated at the end of each year of study. P emerged as the single most important nutrient followed by N and K in order of magnitude. Growth response to N and K were enhanced by the presence of P at both levels. The degree of response was related to the level of each nutrient in the soil. Best growth was obtained in the treatments containing all three nutrients. In conclusion, application of fertilizers to rubber seedlings on the soils used, is justified by the growth increases obtained, especially where all three nutrients were applied together.     

Field-insensitive giant dynamic piezoelectric response and its structural origin in (Ba,Ca)(Ti,Zr)O3 tetragonal-orthorhombic phase-boundary ceramics

BaTiO₃ (BT)-based ceramics usually exhibit superior quasi-static piezoelectric response but relatively low electrostrain, which limits their actuator applications. In this study, lead-free (Ba_0.835+xCa_0.165-x)(Ti_0.91Zr_0.09)O₃ (x = 0–0.06) (Ba_xCTZ) ceramics with the compositions close to the tetragonal (T)-rich side of orthorhombic (O)-T polymorphic phase boundary (PPB) were reported to exhibit a field insensitive giant dynamic piezoelectric response (d₃₃* >1050 pm/V) over a wide electric field range up to 2 kV/mm, resulting in the large strain value of ∼0.21 %. Detailed structural investigations combined with various electrical properties measurements reveal that the superior dynamic piezoelectric response is attributed to the combination of piezoelectric effect and domain switching behavior due to the chemical modulated O-T PPB, and the field induced partially irreversible T-O phase transition. The results demonstrate that the studied compositions have great potential for applications of lead-free actuator piezoceramics.     

Identification and Characterization of Short Crown Root 8, a Temperature-Sensitive Mutant Associated with Crown Root Development in Rice

Crown roots are essential for plants to obtain water and nutrients, perceive environmental changes, and synthesize plant hormones. In this study, we identified and characterized short crown root 8 (scr8), which exhibited a defective phenotype of crown root and vegetative development. Temperature treatment showed that scr8 was sensitive to temperature and that the mutant phenotypes were rescued when grown under low temperature condition (20 °C). Histological and EdU staining analysis showed that the crown root formation was hampered and that the root meristem activity was decreased in scr8. With map-based cloning strategy, the SCR8 gene was fine-mapped to an interval of 126.4 kb on chromosome 8. Sequencing analysis revealed that the sequence variations were only found in LOC_Os08g14850, which encodes a CC-NBS-LRR protein. Expression and inoculation test analysis showed that the expression level of LOC_Os08g14850 was significantly decreased under low temperature (20 °C) and that the resistance to Xanthomonas oryzae pv. Oryzae (Xoo) was enhanced in scr8. These results indicated that LOC_Os08g14850 may be the candidate of SCR8 and that its mutation activated the plant defense response, resulting in a crown root growth defect.     

Accuracy, temporal performance and stability comparisons of discretization methods for the numerical solution of Partial Differential Equations (PDEs) in the presence of steep moving fronts

In this paper, several competitive spatial discretization methods recently developed for the convection term are reviewed and analyzed in terms of accuracy, temporal performance, and stability. This analysis was performed using a prediction–correction DAE integrator within the framework of the MOL (Method Of Lines). The discretization methods are classified by Fixed Stencil (FS), Adaptive Stencil (AS) and Weighted Stencil (WS) approaches and their main characteristics are demonstrated via a number of bench marking tests. Of the 14 discretization methods tested, four have been shown to be the most reliable, when we consider the accuracy of the calculation and the computational time required. Application of commonly-used FS methods to convection-dominated problems containing a moving shock results in a relatively short calculation time. However, almost of the FS methods, except for the first-order upwind FS method, are unstable, providing spurious oscillatory profiles (termed the Gibbs phenomena) near the shock. Employing AS methods such as ENO (Essentially Non-Oscillatory) schemes, this Gibbs phenomena disappears. Therefore, AS methods enhance stability and accuracy but are somewhat prohibitive. WS methods (i.e. Weighted ENO schemes), which use a convex combination of candidate stencils weighted by the ENO idea, can reduce the calculation time, and are inheriting of the non-oscillation nature inherent in the AS methods. The ENO and WENO methods are efficient to track a shock and steep moving front and these methods are essential for numerical schemes which use relatively small number of mesh points.     

A review of surface topographical modification strategies of 3Y-TZP: Effect in the physicochemical properties,microstructure, mechanical reliability,and biological response

The development of zirconia dental implants has become increasingly popular over the last years due to the outstanding mechanical properties, superior aesthetic appearance and high biocompatibility of this material. However, premature implant failure as a result of an incomplete osseointegration still represents a major concern. In this sense, surface modifications have been applied to dental zirconia to improve the biological interactions of the implant with the surrounding tissue. Nevertheless, surface modification of zirconia is challenging due to the formation of a monoclinic phase associated with ageing and loss of mechanical integrity. This review focuses on the most common surface topographical modification strategies currently applied to zirconia, namely grinding, sandblasting, chemical etching and laser treatment. A comprehensive and comparative analysis has been performed to assess the effects of these techniques on the physicochemical properties, mechanical performance, hydrothermal degradation behavior and biological response of the modified surfaces.     

Extraction,Preliminary Characterization and Evaluation of in Vitro Antitumor and Antioxidant Activities of Polysaccharides from Mentha piperita

This study describes the extraction, preliminary characterization and evaluation of the in vitro antitumor and antioxidant activities of polysaccharides extracted from Mentha piperita (MPP). The optimal parameters for the extraction of MPP were obtained by Box-Behnken experimental design and response surface methodology (RSM) at the ratio of water to raw material of 20, extraction time of 1.5 h and extraction temperature at 80 °C. Chemical composition analysis showed that MPP was mainly composed of glucuronic acid, galacturonic acid, glucose, galactose and arabinose, and the molecular weight of its two major fractions were estimated to be about 2.843 and 1.139 kDa, respectively. In vitro bioactivity experiments showed that MPP not only inhibited the growth of A549 cells but possessed potent inhibitory action against DNA topoisomerase I (topo I), and an appreciative antioxidant action as well. These results indicate that MPP may be useful for developing safe natural health products.     

氨改性硅油的合成、表征及其在PAN基碳纤维原丝预氧化过程中的作用

利用八甲基环四硅氧烷(D4)和N,β-乙氨基γ-丙胺基甲基二甲氧基硅烷为主要原料,通过开环缩聚合成了氨改性聚硅氧烷。用红外光谱和核磁共振氢谱、碳谱对其结构进行了表征确认,研究了其在PAN基碳纤维预氧化过程中的作用。结果表明:氨改性聚硅氧烷可以有效地减少PAN原丝在预氧化过程中的并丝现象和纤维与导辊之间的摩擦,从而有效抑制了纤维次生缺陷的产生。     

Photoanodic response of iron oxide electrode in aqueous solution and its application to Pb removal under visible light irradiation

The iron oxide electrode was prepared from thermal oxidation of iron at 600 °C for 3 h in air atmosphere. This electrode with the structure of Fe₃O₄ and α-Fe₂O₃ showed the response of photoanodic current to the light with wavelength shorter than 600 nm. The band gap energy of this electrode was 1.99 eV. The onset potential of distinct steady photocurrent and also the flatband potential were 0.80 and 0.09 V vs. Ag/AgCl, respectively, in 0.1 M HNO₃ aqueous solution. The cell consisting of the iron oxide photoanode in HNO₃-Pb(NO₃)₂ and the graphite cathode in H₂SO₄-Ce(SO₄)₂ caused the PbO₂ deposit on the surface of the former electrode due to visible light irradiation without application of voltage. By holding the potential of this electrode at more positive value than 0.90 V, the photoanodic removal rate of Pb²⁺ in HNO₃-Pb(NO₃)₂ solution was higher than that observed when Ce⁴⁺ was used as electron acceptor.     

Use optimization of natural antioxidants in refined, bleached, and deodorized palm olein during repeated deep-fat frying using response surface methodology

An optimization study on the use of oleoresin rosemary extract, sage extract, and citric acid added into refined, bleached, and deodorized (RBD) palm olein in deep-fat frying of potato chips was carried out using response surface methodology (RSM). Results showed that oleoresin rosemary extract was the most important factor affecting the sensory acceptability of potato chips. For taste and odor, its effects were highly significant (P<0.01), while for crispiness and overall acceptability, the effects were significant (P<0.05). As for sage extract, the level of this antioxidant had a highly significant (P<0.01) effect on appearance and taste and a significant effect (P<0.05) on odor and overall acceptability, but had no effect on crispiness. Although there was no significant synergistic correlation between citric acid and oleoresin rosemary extract or sage extract at the first order, its second order was significantly (P<0.05) related to taste, crispiness, and overall acceptability. An interaction between oleoresin rosemary and sage extracts also significantly (P<0.05) improved the score of overall acceptability of the potato chips. Contour maps of the sensory scores of potato chips indicated that the optimal points for appearance were achieved using 0.062% oleoresin rosemary extract, 0.066% sage extract, and 0.023% citric acid, while optimal task was achieved with 0.063% oleoresin rosemary extract, 0.075% sage extract, and 0.025% citric acid. With the same sequence of ingredients added into oil, the combinations required to achieve the optimal odor, crispiness, and overall acceptability scores were 0.058-0.046-0.026, 0.060-0.071-0.022, and 0.060-0.064-0.026%, respectively.     

Preparation,properties and in vitro cellular response of multi-walled carbon nanotubes/bioactive glass/poly(etheretherketone) biocomposite for bone tissue engineering

Desired bone repair biomaterial must have good biocompatibility and suitable mechanical properties that are equivalent to those of human bones. In this study, multi-walled carbon nanotubes (MWCNTS) was designed to incorporate into bioactive glass/poly(etheretherketone) to fabricate a composite of multi-walled carbon nanotubes/bioactive glass/poly(etheretherketone) (MWCNTS/BG/PEEK) through a compounding and injection-molding process. The microstructures, mechanical properties, thermal stability and bioactivity of the ternary biocomposite, as well as preliminary cell responses of MC3T3-E1 osteoblast cells to this biomaterial, were investigated. The mechanical performance of ternary MWCNTS/BG/PEEK composite was vastly superior to binary BG/PEEK composite. More importantly, cell culture tests showed that cell adhesion, viability and differentiation of MC3T3-E1 cells were significantly promoted on the MWCNTS/BG/PEEK composite. Moreover, it was found that MWCNTS in composite further promoted cell metabolic vitality and osteogenic differentiation of osteoblast cells. Hence, this MWCNTS/BG/PEEK biomaterial may be used as a promising bone graft scaffold in dental and orthopedic applications.