铝合金时效蠕变与时效应力松弛关系研究

分析了材料蠕变与应力松弛的关系,提出了一种由材料蠕变曲线获取应力松弛曲线的转换方法.以铝合金7075T6为试验材料在177℃时效温度下实施了蠕变与应力松弛试验,通过比较试验应力松弛曲线与此转换方法得到的应力松弛曲线,验证了转换方法的准确性.     

考虑基体开裂的陶瓷基复合材料应力-应变曲线模拟方法及验证

提出了蒙特卡罗方法模拟陶瓷基复合材料基体随机开裂过程,采用剪滞模型描述了复合材料出现损伤时细观应力场,并推导得到了考虑基体开裂时复合材料拉伸应力-应变曲线计算公式.开展了室温环境下C/SiC复合材料的单轴拉伸试验,并将理论预测应力-应变曲线与试验结果进行对比.同时,采用该方法对SiC/CAS,SiC/Si₃N₄复合材料应力-应变曲线进行了模拟,并与国外提供的相关试验数据进行比较,发现两者吻合得较好,从而证实了蒙特卡罗法可有效地模拟考虑基体随机开裂过程的陶瓷基复合材料应力-应变曲线.此外,还分析了Weibull模量、残余热应力和初始开裂应力对应力-应变曲线的影响.研究表明:Weibull模量越大,应力-应变曲线非线性越明显;热残余应力越大,应力-应变曲线偏转越早,非线性越明显;初始开裂应力与Weibull模量对应力-应变曲线影响规律相似.      

2.5维自愈合C/SiC复合材料的拉伸应力-应变关系

根据2.5维自愈合C/SiC复合材料的细观结构特点,基于界面开裂和基体开裂的损伤机理,分别建立了该材料经向和纬向拉伸的细观力学模型,进而得到了经向和纬向拉伸的非线性应力-应变关系,应力-应变曲线的预测结果与试验值吻合较好.结果表明:纬向应力-应变曲线的最大预测误差为9%,经向应力-应变曲线的最大预测误差约为10%,经向和纬向的应力-应变关系不同.该模型采用切线弹性模量和平均裂纹间距的方法,省去了以往模型复杂的应变计算过程,使模型得到简化,便于应用.      

3种铝合金材料动态性能及其温度相关性对比研究

 对3种铝合金2024-T351、7050-T7451和LY12-CZ进行了温度在77～573 K的静、动态压缩（应变率10^-3～6 000/s）和拉伸（应变率10^-3～3 000/s）试验,分别得到了3种铝合金材料的应力 应变关系和失效应变。对比研究结果表明,随温度升高3种材料的塑性流动应力降低,应变率敏感性增加。最后基于Johnson-Cook模型,拟合了用以预测铝合金材料塑性流动应力的模型参数,其预测结果与试验结果吻合较好。     

材料疲劳循环特性研究

 本文提出用计算分析模拟疲劳实验得到循环应力-应变曲线。列举材料计算的循环应力-应变曲线与实验结果相符合。     

航空常用铝合金动态拉伸力学性能探究

利用分离式Hopkinson拉杆设备对五种航空常用铝合金2A12-CZ,2A12-M,2024-T351,7050-T74,7050-T7451进行了室温动态拉伸力学性能探究,并利用电子万能试验机对这五种材料进行了准静态拉伸力学性能测试,得到了五种铝合金在不同应变率下的拉伸真实应力应变曲线。试验结果显示:7050系列铝合金有较高的屈服强度,2A12M抗拉强度则最低。五种航空铝合金都表现出不同程度的正的应变率敏感效应,其中2A12-CZ敏感性最强,7050T7451敏感性最弱。五种铝合金动态拉伸失效应变明显大于准静态拉伸失效应变。2A12M与2024T351有较高的动态拉伸失效应变。在试验结果的基础上,选择Johnson-Cook本构模型,Cowper-Symonds本构模型来拟合这五种材料的动态本构,模型预测与试验结果吻合较好。     

一种较简单的低循环疲劳寿命预测法

 <正> 1。引言 局部应力应变法是目前预测结构裂纹起始寿命的一种行之有效的方法。根据局部应力应变法的原理,可以用计算的方法来预测构件裂纹起始寿命。在计算中,从载荷谱得到局部应变谱,可利用有限元法分析结构的局部应力应变响应。当然还可利用半经验公式(如Neuber法等)。在计算中若考虑材料的记忆特性和循环σ-ε曲线,这无疑对真实地反映受载构件的局部应力应变响应是有利的。但要做到这一点,用有限元分析所需的机时相当可观,因为它要对整个寿命期间的载荷历程进行分析计算,至少也要针对一个典型谱分析计算。 计算中材料的循环应力应变曲线一般可采用下式     

纳米压痕硬度计测方法的研究进展

针对纳米尺度下的材料硬度测量,利用纳米硬度计得到压痕的载荷-压深曲线,并用原子力显微镜得到压痕的三维形貌图.通过载荷-压深曲线和压痕形貌图,以及相应的计算方法,可以得到纳米压痕硬度.纳米压痕硬度计测方法不同,得到的材料硬度值也不同.分析现有的几种纳米压痕硬度计测方法,找出它们的优缺点,并对未来发展方向做了展望.     

快速凝固/粉末冶金高阻尼铝合金挤压成形过程的数值模拟

 采用有限元分析软件ANSYS,分析了快速凝固/粉末冶金 (Rapidly Solidified/Powder Metallurgy,RS/PM)高阻尼铝合金FMS0714/10(Zn-30Al)的挤压成形过程,研究了模具与坯料间的摩擦条件和挤压比对阻尼铝合金成形过程的影响,探讨了挤压过程材料表面产生裂纹的机理,进行了成形工艺优化。研究结果表明：挤压过程中FMS0714/10(Zn-30Al) 阻尼铝合金材料的流动与变形不均匀,导致了应力应变分布的不均匀：材料表面应力应变较大,芯部应力应变较小;表面过大的应变和轴向拉应力是表面裂纹的诱因;减小模具和坯料间的摩擦,增大挤压比,可以减小材料表面应力,使应变分布趋于均匀,从而减少材料表面损伤,优化材料表面质量,提高成品合格率。数值模拟的研究结果将为FMS0714/10(Zn-30Al) 阻尼铝合金材料挤压工艺的制订以及新材料的设计和研制提供有益的参考。     

不锈钢材料高温、高应变率下动态力学性能的试验研究

利用带有加热装置和同步组装系统的高温Hopkinson压杆系统对某不锈钢材料在温度20 ～ 800℃时,应变率103 ～ 104s-1下的动态压缩力学性能进行了测试,得到了材料在不同温度和应变率耦合作用下的真实应力-应变曲线.对比准静态结果,考察了材料流动应力的温度和应变率敏感性,并根据热激活位错运动理论对其内在机理进行了解释和探讨.试验表明,材料具有显著的热软化和应变率强化效应;且高温时,材料的温度敏感性、应变率敏感性均显著增加.     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.     

Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl4 and SbCl3 and Azeotropic Drying

Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.     

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).     

超声速燃烧数值模拟中的湍流与化学反应相互作用模型

高精度数值模拟有助于理解超声速湍流燃烧中湍流与化学反应的相互作用,可为发动机燃烧室等工程应用设计提供可靠的预测模型。除直接数值模拟外,目前在湍流燃烧应用中使用的大涡模拟和雷诺平均Navier-Stokes模拟均需要借助模型模化发生在湍流小尺度上的流动与化学反应过程对湍流大尺度运动的影响。现有的湍流与化学反应相互作用模型大致可分为:火焰面类模型和概率密度函数类模型,2类模型在不同的应用中各自具有优势和局限性。此外,现有模型大都基于低马赫数燃烧,而超声速燃烧中通常会伴随快速混合、局部熄火和再着火以及激波等复杂过程,这为发展其中的湍流与化学反应相互作用模型提出了更多的挑战。     

适于低轨卫星IP网络的单核共享树组播算法(英文)

为了解决低轨卫星IP网络中现有典型源组播算法的信道资源浪费问题,本文提出了一套单核共享树组播算法,即核心群合并共享树(CCST)和加权核心群合并共享树(w-CCST)算法。CCST 算法包括动态近似中心(DAC)选核方法和核心群合并组播路径构建方法。DAC方法专为周期、规律运动的低轨卫星网络提出,不需要复杂的星上计算。在核心群合并方法中,以核节点作为初始核心群,通过核心群和剩余组成员的最短路径方法逐步扩展直至整棵组播树构建完成,从而使得组播树的树代价最小,大大提高了网络的带宽利用率和组播传输效率。w-CCST 算法中所提出的加权因子可以调整树代价和端到端传播时延之间的折衷程度,因此,可以通过调整加权因子来适度增大树代价、降低端到端传播时延以支持某些端到端时延要求苛刻的实时组播业务。最后,与低轨卫星 IP 网络中典型算法进行了性能比较,仿真结果说明,CCST 算法的平均树代价比其它算法显著降低,w-CCST 算法的平均端到端传播时延小于 CCST 算法。     

Jet Vectoring Control Using a Novel Synthetic Jet Actuator

A primary air jet vectoring control system with a novel synthetic jet actuator (SJA) is presented and simulated numerically. The results show that, in comparison with an existing traditional synthetic jet actuator, which is able to perform the duty of either “push” or “pull”, one novel synthetic jet actuator can fulfill both “push” and “pull” functions to vector the primary jet by shifting a slide block inside it. Therefore, because the new actuator possesses greater efficiency, it has potentiality to replace the existing one in various appli- cations, such as thrust vectoring and the reduction of thermal signature. Moreover, as the novel actuator can fulfill those functions that the existing one can not, it may well be expected to popularize it into more flow control systems.     

Nonlinear Adaptive Slewing Motion Control of Spacecraft Truss Driven by Synchronous V-gimbaled CMG Precession

The slewing motion control of a truss arm driven by a V-gimbaled control-moment-gyro (CMG) is a nonlinear control problem. The V-gimbaled CMG consists of a pair of gyros that must precess synchronously. The moment of inertia of the system, the angular momentum of the gyros and the external disturbances are not exactly known. With the help of feedback linearization and recursive Lyapunov design method, an adaptive nonlinear controller is designed to deal with the unknown items. Performance of the proposed controller is verified by simulation.     

An SOR Implicit Time-accurate Scheme in Calculating Unsteady Flows

A new time-accurate marching scheme for unsteady flow calculations is proposed in the present work. This method is the combination of classical Successive Over-Relaxation (SOR) iteration method and Jacobian matrix diagonally dominant splitting method of LUSGS. One advantage of this algorithm is the second-order accuracy because of no factorization error. Another advantage is the low computational cost because the Jacobian matrices and fluxes are only calculated once in each physical time step. And, the SOR algorithm has better convergence property than Gauss-Seidel. To investigate its accuracy and convergency, several unsteady flow computa- tional tests are carried out by using the proposed SOR algorithm. Roe’s FDS scheme is used to discritize the inviscid flux terms. Un- steady computational results of SOR are compared with the experiment results and those of Gauss-Seidel. Results reveal that the numerical results agree well with the experimental data and the second-order accuracy can be obtained as the Gauss-Seidel for unsteady flow computations. The impact of SOR factor is investigated for unsteady computations by using different SOR factors in this algorithm to simulate each computational test. Different numbers of inner iterations are needed to converge to the same criterion for different SOR factors and optimal choice of SOR factor can improve the computational efficiency greatly.