高温固相法合成LiNi1/3Mn1/3Co1/3O2及其性能研究

采用高温固相法合成出层状锂离子电池正极材料LiNi_1/3Mn_1/3Co_1/3O₂。通过XRD、ICP、SEM和电化学测试手段对产物的结构、组成、形貌及电化学性能进行了研究。XRD结果表明此方法合成的LiNi_1/3Mn_1/3Co_1/3O₂具有标准的α-NaFeO₂型层状结构，SEM照片显示颗粒粒径大约在500 nm左右，粒径分布较窄。以20 mA·g^-1电流密度放电，充放电电压在2.8～4.4 V之间，其首次放电比容量为170 mAh·g^-1，40次循环容量保持率为85.3%。进一步加入石墨导电剂后，同样条件下首次放电比容量变为179 mAh·g^-1，50次循环容量保持率为89.6%。容量衰减主要发生在前10次循环。XRD和SEM测试表明循环初期容量衰减的原因是由材料本体结构变化和界面反应共同作用的结果。     

锰源对尖晶石LiMn2O4高温性能的影响

为考察不同锰源对所制备尖晶石LiMn₂O₄(LMO)电化学性能的影响(特别是高温性能),采用沉淀法制备前驱体,通过不同煅烧温度制备得到最常用的锰氧化物(MnO₂、Mn₂O₃和Mn₃O₄)为锰源,经相同条件制备得到LMO正极材料,通过考察所得LMO形貌及电化学性能来研究锰源与LMO电化学性能的关系。研究结果表明,相同的前驱体在不同煅烧温度下可以得到不同的锰氧化物,且各自具有不同的形貌结构。由这些锰氧化物都可以得到高纯度的LMO,但产物形貌结构以及材料中的八面体晶体含量和尺寸不同。由Mn₂O₃制备得到的LMO材料中的八面体晶体含量最多,且尺寸最均匀,在3种LMO中容量性能、倍率性能和循环性能最好：0.2C(1C=148 mA·g^-1)下首次放电比容量为131.8 mAh·g^-1;3C下还有100.4 mAh·g^-1的放电比容量。其对应半电池在0.5C下循环100次后,放电比容量还有116.0 mAh·g^-1,容量保持率为93.9%,电化学储能性能远远优于其他2种LMO。即使是在高温55 ℃下,由Mn₂O₃得到的LMO也表现出明显优于其他2种材料的高倍率性能和抗衰减性能。     

离子电池正极材料LiNi0.5Mn0.5O2的合成

采用共沉淀法制备锂离子电池正极材料LiNi_0.5Mn_0.5O₂，前驱体制备过程中金属离子氢氧化物的形貌、粒径分布和最终合成材料的性能息息相关。本文讨论了共沉淀反应过程中沉淀体系、pH值、搅拌速度和氨水浓度对沉淀产物形貌的影响。同时还考察了烧结制度对材料电化学性能的影响。结果表明，在优化条件下制备的正极材料LiNi_0.5Mn_0.5O₂首次放电容量高达178 mAh·g^-1，50个循环后放电容量稳定保持在165 mAh·g^-1(电压范围2.8～4.5 V，电流密度30 mA·g^-1)。     

球磨辅助高温固相法制备Li1.0Na0.2Ni0.13Co0.13Mn0.54O2正极材料及其性能

以乙酸盐(乙酸锂、乙酸钠、乙酸钴、乙酸镍、乙酸锰等)为原材料,采用球磨辅助高温固相法制备Li_1.0Na_0.2Ni_0.13Co_0.13Mn_0.54O₂正极材料。借助XRD、SEM等表征材料的结构和形貌,利用循环伏安、恒流充放电、交流阻抗等方法研究材料的电化学性能。结果表明,钠的掺杂导致颗粒表面光滑度降低,形成Na_0.77MnO_2.05新相。0.05C活化过程中,掺钠样品和未掺钠样品首次放电比容量分别为258.4 mAh·g^-1和215.8 mAh·g^-1,库伦效率分别为75.2%和72.8%;2C放电比容量分别为116.3 mAh·g^-1和106.2 mAh·g^-1。研究发现,掺钠可减小首次充放电过程的不可逆容量,提高容量保持率;改善倍率性能与容量恢复特性;降低SEI膜阻抗和电荷转移阻抗;掺钠后样品首次循环就可以基本完成Li₂MnO₃组分向稳定结构的转化,而未掺杂的样品需要两次循环才能逐步完成该过程;XPS结果表明,掺钠样品中Ni²⁺、Co³⁺、Mn⁴⁺所占比例明显提高,改善了样品的稳定性和电化学性能;循环200次后的XRD结果表明掺钠与未掺钠材料在脱嵌锂反应中的相变化过程基本一致,良好有序的层状结构遭到破坏是循环过程中容量衰减的主要原因。     

MoO3纳米带/RGO复合材料的制备及其电化学性能研究

以水杨酸为模板剂和还原剂,采用水热法制备得到了一种MoO₃纳米带/RGO复合材料。利用XRD、SEM、TEM、拉曼光谱、恒流充放电、交流阻抗等手段对样品的结构、形貌以及电化学性能进行表征。测试结果表明,MoO₃纳米带/RGO复合材料作为锂离子电池负极材料,在50mA·g^-1的电流密度下可逆比容量为1000mAh·g^-1,循环50次后比容量还保持在950mAh·g^-1,相比于MoO₃纳米带其容量保持能力和循环性能得到了显著改善。     

锂离子电池正极材料LiNi0.75-xCoxMn0.25O2的合成及电化学性能研究

以LiOH·H₂O、Ni(OAc)₂·4H₂O、Co(OAc)₂·4H₂O和MnO₂为原料，在水热反应釜中预处理，然后进行高温固相反应，合成了一系列锂镍钴锰氧化物LiNi_0.75-xCo_xMn_0.25O₂(x=0.05,0.10,0.15,0.20,0.25)。通过X射线衍射(XRD)、扫描电子显微镜（SEM）和电化学性能测试对所得样品的结构、形貌、粒径及电化学性能进行了表征。结果表明，当x=0.20时，所合成的正极材料具有很好的α-NaFeO₂型层状晶体结构，晶胞参数a=0.286 1 nm，c=1.416 4 nm， V=0.100 4 nm³，以50 mA·g^-1的电流密度在3～4.3 V(vs Li/Li⁺)充放电时，首次放电比容量达172.5 mAh·g^-1，首次放电效率高达90.9%，30个循环后其放电比容量依然保持在161.1 mAh·g^-1。     

锂离子电池正极材料LiFePO4/ C的合成研究

以三价铁化合物作为铁源，采用碳热还原法一步合成得到锂离子电池正极材料LiFePO₄。利用X射线衍射仪、扫描电镜、碳硫分析法和电化学性能测试方法对磷酸铁锂材料的物相结构、表面形貌、含碳量(质量分数)以及电性能进行分析研究。讨论了烧结温度、烧结时间和掺碳量对材料电性能的影响。结果表明，LiFePO₄的电性能与烧结温度、时间以及掺碳量有密切的关系，在优化试验条件下制备的正极材料LiFePO₄，以电流密度为17 mA·g^-1充放电，首次放电容量达到141.8 mAh·g^-1，80次循环后放电容量为137.7 mAh·g^-1，容量保持率为97.1%。     

三维花状Fe2（MoO4）3微米球的水热制备及电化学性能

以FeCl₃·7H₂O和Na₂MoO₄为原料,采用水热合成法制备三维花状Fe₂（MoO₄）₃微米球。探讨不同合成温度对样品形貌的影响,利用XRD、SEM和EDS等分析技术对样品的结构、形貌进行了表征,对该材料的电化学性能进行了测试。结果表明：Fe₂（MoO₄）₃微米球是由二维纳米片自组装而成的花状结构,合成温度为160℃时,制备的样品具有良好的电化学性能,当电流密度为100mA·g^-1,首次放电比容量为1431mAh·g^-1;并具有较好的循环性能和倍率性能。并对160℃合成样品表现较好电化学性能的原因进行了探讨。     

层状LiMnO2的固相合成及电化学性能

以Mn₂O₃和氢氧化锂为原料，通过焙烧合成出o-LiMnO₂。用X射线衍射和扫描电镜对不同温度下合成的粉末样品进行了表征，并研究了材料的电化学性能。通过对不同温度条件下烧结样品的晶胞参数、布拉格(110)晶面峰半高宽及电化学性能研究发现：600 ℃下合成样品的半高宽最大，堆垛层错率高，同时电化学性能也最好，首次放电容量达到156 mAh·g^-1，20次循环后仍保持在140 mAh·g^-1以上。中高温固相合成的o-LiMnO₂材料，在晶粒范围大小相近时，材料电化学性能与材料堆垛层错率相关。     

钽离子掺杂对LiFePO4 / C物理和电化学性能的影响

采用PAM(聚丙烯酰胺)模板-溶胶凝胶法在惰性气氛下合成钽掺杂的LiFePO₄/C复合正极材料，考察了钽对目标化合物的物理和电化学性能的影响。研究结果表明，0.33C的电流下充放电时，掺杂前后第2个循环的放电容量分别为138.6 mAh·g^-1和155.5 mAh·g^-1，循环20次后容量为141 mAh·g^-1和156 mAh·g^-1。电化学交流阻抗表明，掺杂后的材料阻抗R_ct从180 Ω减小到120 Ω。振实密度比掺杂前提高0.312 g·cm^-3。     

Solvent extraction separation of In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/ with sulphoxides

Solvent extraction studies have been made on some metals: In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/, from ammonium thiocyanate solutions by dialkyl sulphoxides. Separation of these metals from one another can be achieved by suitable choice of the extracted conditions. The nature of the extractable metal species has been elucidated.     

Synthesis of chlorobis/β-diketonato/oxotechnetium/V/ and tris/β-diketonato/technetium/III/ complexes

Chlorobis/-diketonato/ oxotechnetium/V/ complexes [TcOCl/-dik/₂, -diketone=acetylacetone, benzoylacetone and dibenzoylmethane] were newly synthesized using macroamount of⁹⁹Tc. These complexes were further separated into geometrical isomers. Furthermore, an improvement of the yields for the syntheses of tris/-dike-tonato/technetium/III/ complexes [Tc/-dik/₃, -diketone=acetylacetone, benzoylacetone and 2-thenoyltrifluoroacetone] was examined using Tc/III/-thiourea complexes as a starting material.     

Simultaneous propane dehydrogenation andco2hydrogenation overCrOx/SiO2catalyst

Summary Single reverse water-gas shift (RWGS) and dehydrogenation of propane with CO₂(DH-CO₂) reactions in the presence and absence of the CrO_x/SiO₂ catalyst have been studied between 673 and 873 K. It was found that the CrO_x/SiO₂ catalyst is active both in the dehydrogenation of propane and in the RWGS reactions. The obtained results suggest that the dehydrogenation of propane to propene in the presence of CO₂on CrO_x/SiO₂can be facilitated by the RWGS reaction.</o:p>     

Direct synthesis of dimethyl carbonate ?from CH3OH AND CO2 by H3PW12O40/CexTi1-xO2 catalyst

Summary Ce_xTi_1-xO₂ and H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts were prepared using a sol-gel method, and applied to the direct synthesis of dimethyl carbonate from methanol and carbon dioxide. H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ showed a better catalytic performance than the corresponding Ce_xTi_1-xO₂, due to the bifunctional catalysis of Br?nsted acid sites (provided by H₃PW₁₂O₄₀) and base sites (provided by Ce_xTi_1-xO₂). H₃PW₁₂O₄₀/Ce_0.1Ti_0.9O₂ showed the highest catalytic performance among the H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts.     

Crystal structure of Na3PO4 · 12H2O

The crystal structure of trisodium monophosphate hemihydrate was determined. The space group is $\text{C2}\text{c}$ and a unit cell contains eight formula units. The unit cell dimensions of $\text{Na}{}_3\text{PO}{}_4\text{·}\text{1}\text{2}\text{H}{}_2\text{O}$ are a = 9.631(3), b = 5.416(2), c = 16.938(8) Å, β = 102.60(5)°. The final R value is 0.027 for a set of 1430 independent reflections. This atomic arrangement is mainly a three-dimensional network of distorted NaO₆ octahedra. The hydrogen bonding scheme is given.     

LixNi0.8-yCo0.2ZnyOp的合成及电化学性能研究

A series of single-phase Li_xNi_0.8-yCo_0.2Zn_yO_p(0.96 ≤x≤ 1.10， 0 ≤y≤ 0.05， 2 ≤p≤ 2(1+y) ) (different in the y values) were synthesized by a two-step solid state reaction method， in which LiOH·H₂O， Zn-doped spherical Ni(OH)₂ and Co₂O₃ were used as the precursors. The ICP-AES analyses proved that the Zn-doped compounds synthesized had the nonstoichiometric form. The results of the XRD， SEM identified that the uniform particles of the as-prepared materials having a good layered structure were fine， narrowly distributed and well crystallized. The electrochemical performance test was carried out and the results showed that the as-prepared Zn-doped materials had not only a high capacity， but also a better cycling stability characterization than the un-doped one. The Li_1.06Ni_0.75Co_0.22Zn_0.03O_2.03 material has an initial reversible capacity as high as 160.5mAh·g^-1; and a first discharge efficiency 89.2%， and exhibits satisfactory cyclic stability with 90% retainable capacity after 50 cycles.     

An investigation of the promotional effect of propylene or propane traces on the activity of sulfatedPt/g-Al2O3andPt-Sn/g-Al2O3inCH4combustion

Summary A strong promoting effect of the presence of C₃H₈or C₃H₆was determined for the combustion of CH₄in excess oxygen, over pre-sulfated 1%Pt/g-Al₂O₃and pre-sulfated 1%Pt-2%Sn/g-Al₂O₃catalysts.</o:p>     

Synthesis and characterization of Ti1−2xNbxNixO2−x/2 solid solutions

Doped-rutile has been traditionally used in ceramic pigments for its intense optical properties. In this paper, we compare the classical ceramic synthesis of Ti_1−2xNb_xNi_xO_2−x/2 system with the sol-gel methodology, which allows a reduction of the anatase-rutile transformation temperature. The composition was optimised in order to obtain a unique rutile phase with the minimum amount of pollutant Ni(II) and enhanced chromatic coordinates. Incorporation of the doping ions in the rutile structure was corroborated by XRD and Rietveld refinements. The species responsible for the colour mechanism were studied by different techniques. UV-VIS spectroscopy showed the characteristic features of Ni²⁺ ions, whose existence was corroborated by EPR and magnetic measurements. From these results, (Ni,Nb)doped-TiO₂ powder samples can be now shaped as thin films, monoliths, etc. by using sol-gel methodology without modifying their properties. This study introduces new possibilities of coloured TiO₂-based solid solutions in new combined advanced applications (colouring agent and photocatalyst, etc.).     

Visible light-sensitive yellow TiO2−xNx and Fe-N co-doped Ti1−yFeyO2−xNx anatase photocatalysts

Nitrogen substituted yellow colored anatase TiO_2−xN_x and Fe-N co-doped Ti_1−yFe_yO_2−xN_x have been easily synthesized by novel hydrazine method. White anatase TiO_2−δ and N/Fe-N-doped samples are semiconducting and the presence of ESR signals at g ∼1.994-2.0025 supports the oxygen vacancy and g∼4.3 indicates Fe³⁺ in the lattice. TiO_2−xN_x has higher conductivity than TiO_2−x and Fe/Fe-N-doped anatase and the UV absorption edge of white TiO_2−x extends in the visible region in N, Fe and Fe-N co-doped TiO₂, which show, respectively, two band gaps at ∼3.25/2.63, ∼3.31/2.44 and 2.8/2.44 eV. An activation energy of ∼1.8 eV is observed in Arrhenius log resistivity vs. 1/T plots for all samples. All TiO₂ and Fe-doped TiO₂ show low 2-propanol photodegradation activity but have significant NO photodestruction capability, both in UV and visible regions, while standard Degussa P-25 is incapable in destroying NO in the visible region The mid-gap levels that these N and Fe-N-doped TiO₂ consist may cause this discrepancy in their photocatalytic activities.     

LixZryOz三元化合物的制备及表征

采用高温固相法制备了4种高纯度晶相组成的LixZryOz三元化合物,研究了焙烧温度、时间、反应物的种类和初始反应物物质的量比对产物组成的影响,进一步用XRD、SEM及BET分析方法对产物的晶相结构、表面形貌及比表面积进行了表征.实验结果表明,Li2CO3与ZrO2在适当条件下可以合成得到单斜相Li3ZrO3;以LiOH替代Li2CO3,在适当条件下可以分别合成得到四方相Li2ZrO3和三斜/单斜相Li6Zr2O7;进一步以Zr(NO3)4·5H2O代替Zr02,可将单斜相Li6Zr2O7的制备时间由96 h缩短至24 h.SEM照片显示产物硬团聚明显,粒径分布在1～10μm间,BET分析表明样品比表面积处于1.0～9.0 m2·g-1间分布,反应过程中锂的过量以及长时间高温焙烧是引起产物粒径长大和产生硬团聚的主要原因.