Experimental and numerical investigations of scale-up effects on the hydrodynamics of slurry bubble columns

Experiments and simulations were conducted for bubble columns with diameter of 0.2 m(180 mm i.d.), 0.5 m(476 mm i.d.) and 0.8 m(760 mm i.d.) at high superficial gas velocities(0.12–0.62 m·s-1) and high solid concentrations(0–30 vol%). Radial profiles of time-averaged gas holdup, axial liquid velocity, and turbulent kinetic energy were measured by using in-house developed conductivity probes and Pavlov tubes. Effects of column diameter, superficial gas velocity, and solid concentration were investigated in a wide range of operating conditions. Experimental results indicated that the average gas holdup remarkably increases with superficial gas velocity, and the radial profiles of investigated flow properties become steeper at high superficial gas velocities. The axial liquid velocities significantly increase with the growth of the column size, whereas the gas holdup was slightly affected. The presence of solid in bubble columns would inhibit the breakage of bubbles, which results in an increase in bubble rise velocity and a decrease in gas holdup, but time-averaged axial liquid velocities remain almost the same as that of the hollow column. Furthermore, a 2-D axisymmetric k–ε model was used to simulate heterogeneous bubbly flow using commercial code FLUENT 6.2. The lateral lift force and the turbulent diffusion force were introduced for the determination of gas holdup profiles and the effects of solid concentration were considered as the variation of average bubble diameter in the model. Results predicted by the CFD simulation showed good agreement with experimental data.     

连续内环流三相反应器局部流动特性

在φ200 mm×2500 mm连续内环流三相反应器内,考察了空气 水 玻璃珠体系反应器内局部流动参数随操作条件的变化规律。结果表明,导流筒内截面平均气含率随表观气速的增大而增大,较之气液两相流,在低固含率时,加入固体对气含率影响不明显,而在较高固含率下,气含率有明显降低,但固体再增加时对气含率变化影响不大。在较低表观气速下,进料浆速对导流筒内气含率轴向分布趋势有一定的影响,但在较高表观气速下影响不大,导流筒内的气含率大于环隙内的气含率且随气速增大差别更加明显,浆相连续有利于气相分散并增大环隙内的气含率。导流筒内循环浆速径向分布呈抛物状,中心高、近壁处低,受进料浆速和入口固含率影响都不大。浆相循环强度最低为20,高可达180。固含率轴、径向分布受表观气速和进料浆速的影响,固含率轴、径向分布基本均匀,随进料浆速增加,反应器内固含率降低。     

高长径比三相内环流反应器中细颗粒相含率和循环液速的分布研究

在高径比为22的三相内环流反应器中,在常温常压下以空气-水-石英砂为物系,研究了在不同粒径下上升区固含率、下降区固含率和上升区循环液速随表观气速的变化规律和不同粒径下轴向固含率的分布情况,以及在固体体积分数不同的条件下,平均气含率和上升区气含率随表观气速的变化情况。结果表明:当粒径(ds)≤0.3 mm时,上升区固含率随表观气速的增加呈平缓变化趋势,下降区固含率随表观气速的增加而增加;当0.3 mm相似文献   

Hydrodynamics and bubble behaviour in a three-phase two-stage internal loop airlift reactor

Local hydrodynamics of a gas–liquid–solid system,such as bubble circulation regime,gas holdup,liquid velocity and axial profile of solid concentration,are studied in a two-stage internal loop airlift reactor.Empirical correlations for gas holdup and liquid velocity are proposed to ease the reactor design and scale-up.Different bubble circulation regimes were displayed in the first(lower) and second(upper) stages.Increasing superficial gas velocity and solid loading can promote regime transition of the second stage,and the gas holdup of the second stage is higher than that of the lower stage.In addition,the effects of solid loading on bubble behaviour are experimentally investigated for each stage.It is found that bubble size in the downcomer decreases with the presence of solid particles,and bubble size distribution widens under higher superficial gas velocity and lower solid loading.     

Hydrodynamics of an annulus airlift reactor

The hydrodynamics of an annulus airlift reactor (AALR) was studied and compared with that of a slurry bubble column reactor (SBCR) with silica sands of 75-125 μm in size as solids, city tapping water as liquid phase, and air as gas phase in the present investigation. The effects of superficial gas velocity and solids concentration on gas holdup and solids distributions were investigated. The results showed that the local average gas holdup decreased along the column height, and the average gas holdup decreased with the increasing solids concentration, but this tendency became less at higher solids concentrations. It was found that the effect of superficial gas velocity on axial solids distribution was negligible over the gas velocity range investigated, as long as the solids in the column could be suspended. Increasing solids concentration led to flatter axial solids holdup profiles. The axial distributions of solids concentration and gas holdup in the AALR were much more uniform than those in the SBCR, and slurry circulation in the AALR damped the effects of increasing solids concentration on the hydrodynamics. These advantages of an AALR over a SBCR are especially important for some catalytic reaction processes in three-phase systems such as Fischer-Tropsch synthesis and methanol synthesis.     

LOCAL HYDRODYNAMICS IN AN EXTERNAL LOOP AIRLIFT SLURRY REACTOR WITH AND WITHOUT A RESISTANCE-REGULATING ELEMENT

The hydrodynamic behavior of an external loop airlift slurry reactor (ALSR) with and without a resistance-regulating element was studied with a fiber optic probe and ultrasound Doppler velocimetry. The influences of the superficial gas velocity and solid holdup on the global gas holdup and radial profiles of the suspension circulation velocity in the downer and of gas holdup, bubble size, and bubble rise velocity in the riser were studied. Local measurements allow a better understanding of the flow behavior in the reactor and can be used for CFD modeling and validation. Experimental results show that the resistance-regulating element increases the gas holdup and decreases the suspension circulation velocity, indicating that an optimum design of the flow resistance is needed to obtain the maximum gas-liquid volumetric mass transfer coefficient for a specific superficial gas velocity. A high superficial gas velocity and low solid holdup are favorable for increased uniformity of the radial profile of the gas holdup and bubble rise velocity. Hydrodynamic models that predict the gas holdup and suspension circulation velocity were developed for an ALSR with and without a resistance-regulating element. Good agreement was obtained between measured and predicted values.     

LOCAL HYDRODYNAMICS IN AN EXTERNAL LOOP AIRLIFT SLURRY REACTOR WITH AND WITHOUT A RESISTANCE-REGULATING ELEMENT

The hydrodynamic behavior of an external loop airlift slurry reactor (ALSR) with and without a resistance-regulating element was studied with a fiber optic probe and ultrasound Doppler velocimetry. The influences of the superficial gas velocity and solid holdup on the global gas holdup and radial profiles of the suspension circulation velocity in the downer and of gas holdup, bubble size, and bubble rise velocity in the riser were studied. Local measurements allow a better understanding of the flow behavior in the reactor and can be used for CFD modeling and validation. Experimental results show that the resistance-regulating element increases the gas holdup and decreases the suspension circulation velocity, indicating that an optimum design of the flow resistance is needed to obtain the maximum gas-liquid volumetric mass transfer coefficient for a specific superficial gas velocity. A high superficial gas velocity and low solid holdup are favorable for increased uniformity of the radial profile of the gas holdup and bubble rise velocity. Hydrodynamic models that predict the gas holdup and suspension circulation velocity were developed for an ALSR with and without a resistance-regulating element. Good agreement was obtained between measured and predicted values.     

HYDRODYNAMICS, MIXING AND MASS TRANSFER IN A LARGE DIAMETER JET BUBBLE COLUMN

Experimental measurements for the axial and radial variations in gas holdup, axial and radial dispersion coefficients, volumetric gas-liquid mass transfer coefficient and liquid phase circulation velocity in a cone of a large diameter (122 cm) jet bubble column are presented. Two diameters of the inlet nozzle, namely 10.16 cm and 15.24 cm, three superficial gas velocities (based on cylinder diameter), 3 cm/sec, 6 cm/sec and 8 cm/sec and two superficial liquid velocities, 0.3 cm/sec and 0.6 cm/sec, are examined. The experimental data are obtained for two different bed heights.

The experimental data showed significant axial and radial variations in the gas holdup. The volumetric average gas holdup was higher at higher gas velocity and larger nozzle diameter and somewhat higher at lower liquid velocity. The axial dispersion was high while the radial dispersion was low. The volumetric gas-liquid mass transfer coefficient was larger at higher gas velocity and larger nozzle diameter. The liquid recirculation begins only at the upper end of the cone. In general, experimental data indicate that a jet bubble column provides a high degree of mixing and transport rates.     

三相气升式环流反应器内上升区相含率轴向分布与循环液速的研究

常温常压下,在三相气升式内环流反应器中,将硅铝球、石英砂和瓷球分别与空气、水组成三相物系,考察了细颗粒与大颗粒物系中上升区相含率轴向分布规律、固体装载率和颗粒粒径对该规律的影响,以及各物系中上升区循环液速随表观气速的变化规律。结果表明:随轴向高度的增加,瓷球物系中上升区固含率εsr先增大后减小;硅铝球物系中εsr减小;石英砂物系中εsr均匀分布。随轴向高度的增加,瓷球物系中上升区气含率εgr增大;硅铝球物系中εgr减小;石英砂物系中εgr先增大后减小。固定表观气速,各轴向位置处的上升区气含率随固体装载率、颗粒粒径的增大而增大。当固体装载率相同时,各物系中上升区循环液速随表观气速的增大而增大。     

高长径比环流反应器中气、固含率的轴向分布研究

在高长径比(H/D=22.2)内环流反应器中,常温常压下,以空气-水-石英砂为物系,研究了表观气速和固体装载量对平均气含率、下降区气含率、上升区固含率、下降区固含率的影响,以及上升区气含率、固含率随轴向高度的分布规律.结果表明:平均气含率、下降区气含率随着表观气速的增加而增加,随ω(固体)增大而下降,ω(固体)≤2.6...     

Phase distributions in a gas–liquid–solid circulating fluidized bed riser

The distributions of the three phases in gas–liquid–solid circulating fluidized beds (GLSCFB) were studied using a novel measurement technique that combines electrical resistance tomography (ERT) and optical fibre probe. The introduction of gas into a liquid–solid circulating fluidized bed (LSCFB), thus forming a GLSCFB, caused the increase of solids holdup due to the significantly decreased available buoyancy with the lower density of the gas, even with a somewhat increased liquid velocity due to the decreased liquid holdup giving space for the gas holdup. The gas passed through the riser in the form of bubbles, which tended to flow more through the central region of the riser, leading to more radial non‐uniformity in radial holdup of the phases. The gas velocity has the most significant effect on the gas phase holdup. While the gas velocity also has an obvious effect to the solids holdups, the liquid flow rate had a much more considerable effect on the phase holdups. The solids circulation rate also had a significant effect on the phase holdups, with increasing solids circulation rate causing much more increased solids holdup in the central region than close to the wall. A correlation was developed for the relative radial distributions of solids holdup in GLSCFB, as such radial profiles were found similar over a wide range of operating conditions, like those in a typical gas–solid circulating fluidized beds (GSCFB). Finally, the axial solids profiles in a GLSCFB was found to be much closer to those in an LSCFB which are very uniform, than those found in a GSCFB which are less uniform and sometime having a S shape. Water was used as the continuous and conductive phase, air was the gas phase and glass bead and lava rock particles were used as the solid and non‐conductive phase.     

Experimental investigation on multiscale hydrodynamics in a novel gas–Liquid–Solid three phase jet-Loop reactor

Multiphase flow hydrodynamics in a novel gas–liquid–solid jet-loop reactor (JLR) were experimentally investigated at the macroscales and mesoscales. The chord length distribution was measured by an optical fiber probe and transformed for bubble size distribution through the maximum entropy method. The impacts of key operating conditions (superficial gas and liquid velocity, solid loading) on hydrodynamics at different axial and radial locations were comprehensively investigated. JLR was found to have good solid suspension ability owing to the internal circulation of bubbles and liquid flow. The gas holdup, axial liquid velocity, and bubble velocity increase with gas velocity, while liquid velocity has little influence on them. Compared with the gas–liquid JLRs, solids decrease the gas holdup and liquid circulation, reduces the bubble velocity and delays the flow development due to the enhanced interaction between bubbles and particles (Stokes number >1). This work also provides a benchmark data for computational fluid dynamics (CFD) model validation. © 2019 American Institute of Chemical Engineers AIChE J, 65: e16537, 2019     

表观气速对气升式环流反应器性能的影响

利用计算流体力学(CFD)数值模拟方法.采用Euler法双流体模型研究了表观气速对气液两相气升式环流反应器的液体循环速率和气含率的影响.实验结果与数值模拟结果吻合较好.结果表明.气含率和液体速率在反应器内分布不均匀,气含率在相同的径向位置变化很小,液体速率随着表观气速的增加而增加.     

湍动浆态床流体力学研究（Ⅰ）气含率及其分布规律

对高气速、高固含率、大塔径条件下的湍动浆态床平均气含率和气含率径向分布进行了实验测定,结合工业实验数据,归纳出可用于工业条件的气含率计算关联式,给出了简化的流体力学模型用于气含率分布的模拟。结果表明,浆态床气含率将随塔径增加而降低,固含率与塔径之间存在交互影响;同时,气含率的径向分布也随气速和塔径的增大而改变,存在明显的放大效应,简化模型能够较好地模拟实验结果。     

三相环流反应器中的局部相含率

将压差法与气-液相间滑移速度相结合,提出了利用压差法测量三相区局部相含率的新方法,将测得的局部固含率进行轴向平均并与由颗粒装填量计算所得的固含率进行比较,证明了此方法的可靠性. 利用所提出的测量方法,考察了三相环流反应器中气含率和固含率随操作条件的变化规律. 结果表明,气含率随表观气速的升高而增大,且随轴向位置的升高而增大;大颗粒具有破碎气泡的作用,能够增大反应器内的气含率;固含率随表观气速的增加而降低,且沿轴向变化较大. 表观气速较高时,固含率沿轴向近似呈S形分布.     

Axial hydrodynamic studies in a gas-liquid-solid circulating fluidized bed riser

Axial distribution of phase holdups was studied in the riser of a gas-liquid-solid circulating fluidized bed (GLSCFB). The effects of gas and liquid superficial velocities as well as solids circulation rate on radial distribution of phase holdups at different axial locations were investigated. Electrical resistance tomography (ERT) and optical fiber probe were employed online in the experiments for a precise determination of phase holdups. An empirical model was developed for the determination of gas bubbles in analysis of data obtained by fiber optic sensor. Gas holdup was higher at the central region of the riser and increased axially due to coalescence of small bubbles and decrease of hydrostatic pressure at higher levels in the riser. This led to an increase in solids holdup in regions close to the wall which was slightly higher than the solids holdup at the wall. Both solids and liquid holdups were lower in the central region and increased radially towards the wall. Gas holdup decreased with increasing solids circulation rate but opposite trend was observed for solids holdup. Solids circulation rate had negligible effect on liquid holdup at lower axial locations compared to top of the riser. Cross-sectional average of solids, gas and liquid holdups did not change significantly at higher liquid superficial velocities.     

气液外环流反应器中气泡行为的实验研究

详细考察了气液外环流反应器中上升管、下降管的气泡行为随轴向、径向的变化规律. 由于外环流反应器的结构特点,发现在上升管底部存在偏流,并对分布板区气泡行为随角向的变化规律进行了研究. 分析实验结果得出,气含率和气泡速度均随表观气速的升高而升高;在上升管内,气含率和气泡速度自中心向边壁逐渐降低,而沿轴向变化很小;在分布板区,由于受分布器及下降管的影响,使气含率和气泡速度在不同角向存在不同的径向分布. 在下降管中,气含率自中心向边壁逐渐降低,而气泡速度则基本不变;且下降管中的气体循环率随表观气速的升高而升高.     

气液固三相流化床局部相含率轴径向分布

应用开发的微电导探针测试技术,对小尺寸颗粒玻璃珠（粒径分别为0.48、0.80、1.25 mm）和1.45 mm苯乙烯树脂为固相,空气和水分别为气相和液相的三相流化床的各相局部含率进行了同时测定.在较宽操作条件下,获得了一系列局部相含率实验数据.通过对实验数据研究发现：在充分发展段,局部固含率在r/R=0.75～0.85范围内有一个极大值,床层截面平均气含率随表观液速的变化存在一个极小值.在气体分布器区,在距气体分布器轴向一定距离范围内,三相局部含率的径向分布存在明显的不对称分布.随着轴向距离的增加,局部气含率径向不对称分布逐渐消失,最终过渡到对称分布,而局部固含率的径向不对称分布消失得不明显.     

高长径比三相内环流反应器中相含率的分布研究

在长径比为22的三相内环流反应器中,常温常压下,以空气-水-石英砂为物系,根据无因次准数建立了气含率、固含率的预测模型,考察了在不同粒径下上升区气含率、下降区气含率和上升区固含率、下降区固含率随表观气速的变化规律和不同固体体积分数下轴向固含率的分布情况。结果表明：不同粒径下上升区和下降区气含率均随表观气速的增大而增大;当粒径（ds）≤0．3mm时,上升区固含率随表观气速的增加呈平缓趋势,下降区固含率随表观气速的增加而增加,当0．3mm〈d。≤1．2mm时,上升区固含率随表观气速的增加而呈先下降后增加的趋势,下降区固含率随表观气速的增加而下降;不同固体体积分数下的固体颗粒的固含率随着轴向高度的增大而变化平缓,能够均匀的分布在反应器中;气含率和固含率的计算值和实验值吻合较好,其平均相对误差分别为6．32％、4．56％。     

三相环流反应器流体力学行为

气升式三相环流反应器综合了鼓泡塔和机械搅拌釜的优良性能,具有结构简单、无机械传动部件、易密封、造价低、容易实现工业放大等优点,在石油、化工、电化学和生物化工等领域得到了广泛应用．随着能源形势的日趋紧张,环流反应器在液相法合成甲醇、浆态床一步法合成二甲醚、煤液化等过程中的应用得到许多研究人员的重视,并取得了重要的研究进展．由于目前对其内部流动行为尚缺乏系统的认识,进行工业设计和操作过程中仍显理论指导不足