Ba/Fe-堇青石固溶体(Ba0.05Fe0.1Mg)2Al4Si5O18的组合筛选及红外辐射性能优化

采用组合材料方法制备并筛选了具有高红外辐射性能的Ba/Fe共掺堇青石固溶体(Ba_0.05Fe_0.1Mg)₂Al₄Si₅O₁₈. 通过组合溶液喷射法,制备了7×7阵列的样品库,并在不同温度下进行热处理.通过X射线衍射、红外热成像等测试方法分析了Ba²⁺、Fe³⁺固溶对堇青石晶格畸变和红外辐射性能的影响. 经过放大制备实验的验证,确定了材料的最佳组分为5%Ba²⁺和10%Fe³⁺共固溶的堇青石. 最佳组分样品在100 oC时的红外辐射率在5-24 μm波段均高于0.8.     

Tm3+/Yb3+ ∶LaF3纳米体系中掺杂Yb3+ 离子对Tm3+ 离子荧光发射的影响

为研究Yb³⁺离子浓度变化对Tm³⁺离子在蓝色波段荧光强度的影响,以NaF和La(NO₃)₃为原料,采用水热法制备了Tm³⁺和Yb³⁺共掺的Tm³⁺/ Yb³⁺∶LaF₃纳米颗粒.用X射线衍射对LaF₃纳米颗粒进行表征的结果显示,纳米晶体结构呈六方相.透射电镜的观测结果显示,纳米颗粒样品大小均匀、分散性良好.在波长为800 nm的激光激发下,观测到了上转换蓝光发射,其中包括波长为474 nm和479 nm的较强的荧光辐射(相应的跃迁为1G4→3H6)和波长位于450 nm的强度较弱的荧光发射(相应的跃迁为1D2→3F4).通过观测不同Yb³⁺离子浓度条件下共掺Tm³⁺/Yb³⁺∶LaF₃样品的荧光光谱,研究了Yb³⁺离子掺杂浓度对于Tm³⁺离子的荧光发射的影响,并探讨了产生这种现象的原因.研究结果显示,对于1G4→3H6跃迁产生的荧光发射(474 nm),当Yb³⁺离子浓度增大时,反向能量传递速率的增加导致了荧光强度的增大.然而,当Yb³⁺离子浓度增大到一定程度时,Yb³⁺离子激发态能级寿命的减少将引发荧光强度的下降.相比较而言,Yb³⁺离子的浓度的变化对于1D2→3F4跃迁产生的位于450 nm处荧光强度的影响较弱.     

Er3+及Er3+/Yb3+掺杂ZrO2-Al2O3的制备及发光性质

采用共沉淀法制备了纳米晶ZrO₂-Al₂O₃∶Er³⁺发光粉体.所制备的粉体室温下具有Er3+离子特征荧光发射,主发射在绿光,其中位于547 nm、560 nm的绿光最强,并得出稀土离子与基质之间有能量传递.对不同煅烧温度下的样品研究表明:因不同温度下所制得的样品晶相不同.研究了纳米晶ZrO2-Al2O3∶Er3+及ZrO₂-Al₂O₃∶Er³⁺/Yb³⁺的上转换发光,并分析了上转换的跃迁机制.发现ZrO₂-Al₂O₃∶Er³⁺的绿光为双光子过程,而ZrO₂-Al₂O₃∶Er³⁺、Yb³⁺的上转换光谱中,红光和绿光也为双光子过程,而极弱的蓝光为三光子过程.讨论了Er³⁺的浓度猝灭现象.最适宜掺杂浓度的原子分数为2%（Er³⁺/Zr⁴⁺）.     

多壁碳纳米管对p型Ba0.3FeCo3Sb12化合物热电性能的影响

用两步固相反应法合成了p型Ba填充方钴矿化合物Ba^0.3FeCo³S b^１2，并采用放电等离子烧结法(SPS)制备了Ba^0.3FeCo³Sb^１2／多壁碳纳米管复合材料. 研究了Ba^0.3FeCo³Sb^１2／多壁碳纳米管复合 材料的结构及多壁碳纳米管对 其热电性能的影响规律：SEM分析表明多壁碳纳米管比较均匀地分布在Ba^0.3 FeCo³S b^１2基体中；随着碳纳米管添加量的增加，Ba^0.3FeCo3Sb^１2/多壁碳 纳米管复合材料的电导率下降、塞贝克系数略微下降、晶格热导率大幅度降低，当碳纳米管 含量为5％时其晶格热导率最小；当碳纳米管的含量为3％时，本研究得到的Ba^{0.3FeCo3Sb１2/碳纳米管复合材料的最大ZT值达078.}     

Structures and luminescence properties of Yb3＋ in the double perovskites Ba2YB＇O6 （B＇=Ta5＋, Nb5＋） phosphors

The Yb³⁺ doped Ba₂YB'O₆ (B'=Ta⁵⁺, Nb⁵⁺) were prepared by high temperature solid-state reaction method, their structures were determined by x-ray diffraction and refined by Rietveld method. The diffuse reflection absorption, excitation and emission spectra of Yb³⁺:Ba₂YB'O₆ (B'=,Ta⁵⁺, Nb⁵⁺) were measured at room temperature. Under the excitation of ultraviolet light, these phosphors exhibit broad charge transfer band emissions of TaO₆ or NbO₆ centre with large Stokes shift. The Yb³⁺ doped into these hosts are situated at Y³⁺ sites of cubic symmetry (O_h). The experimental energy levels of Yb³⁺ in Ba₂YTaO₆ and Ba₂YNbO₆ were determined by photoluminescence and diffuse reflection absorption spectra. Their wavefunctions and theoretical energy levels were obtained by diagonalising the Hamiltonian matrix. The experimental energy levels were fitted by Levenberg--Marquardt iteration algorithm to determine crystal field parameters. Then, the magnetic-pole transition line strengths of Yb³⁺:Ba₂YB'O₆(B'=Ta⁵⁺, Nb⁵⁺) from (²F_5/2)Γ₈^- to the low-energy states were calculated.     

Gd2O3:Eu3+纳米晶的燃烧合成及光致发光性质

采用柠檬酸作燃烧剂用燃烧合成法制备了Gd₂O₃:Eu³⁺纳米晶.用X射线衍射仪(XRD)、高分辨透射电子显微镜(HRTEM)和荧光分光光度计等对Gd₂O₃:Eu³⁺纳米晶的结构、形貌和发光性能进行了分析.结果表明：不同柠檬酸与稀土离子配比(C/M)制备的样品经800℃ 退火1 h后，均得到了纯立方相的Gd₂O₃:Eu³⁺纳米晶，晶粒尺寸约为30 nm，尺寸分布较窄，其中以C/M=1.0时制备的纳米晶结晶性最好，发光强度最大.Gd₂O₃:Eu³⁺纳米晶主发射峰位置均在612 nm处 (⁵D₀→⁷F₂跃迁)，激发光谱中电荷迁移态发生红移，观察到Gd³⁺向Eu³⁺的有效能量传递.对柠檬酸与稀土离子配比(C/M)对结晶度、发光性质等的影响也进行了分析和讨论.     

Ag+掺杂的立方相Y2O3:Eu纳米晶体粉末发光强度研究

采用化学自燃烧法制备了不同Ag⁺掺杂浓度的Y₂O₃:Eu纳米晶体粉末样品(［Y³⁺］∶［Eu³⁺］∶［Ag⁺］=99∶1∶X，X=0—3.5×10^-2)，以及通过退火处理得到了相应的体材料.根据X射线衍射谱确定所得纳米和体材料样品均为纯立方相.实验表明在纳米尺寸样品中随着Ag离子浓度的增加，荧光发射强度随之增加，当X=2×10^-2时达到最大值，其发光强度比X=0时提高了近50%.当Ag离子浓度继续增加，样品发光强度保持不变.在相应的体材料样品中则没有观察到此现象.通过对各样品的发射光谱，激发光谱，X射线衍射图谱，透射电镜(TEM)照片和荧光衰减曲线的研究，分析了引起纳米样品荧光强度变化的原因是由于Ag离子与表面悬键氧结合，从而使这一无辐射通道阻断，使发光中心Eu³⁺的量子效率提高；Ag⁺的引入所带来的另一个效应是使激发更为有效.这两方面原因使发光效率得到了提高.     

Sr2CeO4电荷迁移发光的光谱结构规律研究

利用高温固相反应法分别合成了不同物相形成机理的Sr₂CeO₄，Sr ₂CeO₄∶Ca ²⁺和Sr₂CeO₄∶Ba²⁺样品，并对其光谱特性进行 了研究.结果发现，对于由SrO和CeO₂直接反应生成的Sr₂CeO₄(Ⅰ)，激发主峰位于256nm 左右；而对于SrCeO₃和SrO反应生成的Sr₂CeO₄(Ⅱ)，激发主峰位于279nm左右.在Sr₂CeO₄(Ⅰ)中掺入Ca²⁺，其激发光谱随着Ca²⁺离子浓度的增加逐渐接近于Sr₂CeO_{4(Ⅱ)的激发光谱.激发主峰带应属于CeO6八面体终端Ce⁴⁺—O^2-键的电荷迁移 带.对于激发光谱中340nm左右的弱激发峰，其峰值波长不受形成机理及Ca²⁺掺杂的影响，只是其强度 随着 激发主峰的红移而增加，它可能属于CeO6八面体平面上Ce⁴⁺—O2-键的电荷 迁移带.形成机理及Ca²⁺掺杂对发射光谱没有影响.Ca²⁺在Sr 2CeO 4(Ⅱ)与Ba²⁺在Sr2CeO4(Ⅰ)和(Ⅱ)中均难 于替代Sr²⁺的位置.}     

Er3+/Ce3+共掺TeO2-Bi2O3-TiO2玻璃的热稳定性和光谱特性研究

用高温熔融法制备了Er³⁺/Ce³⁺共掺新型碲酸盐玻璃(TeO₂-Bi₂O₃-TiO₂).采用差热分析方法研究了玻璃的热稳定性,测试并分析了不同Ce³⁺离子掺杂浓度下Er³⁺离子的吸收光谱、上转换光谱和荧光光谱特性.研究结果表明,制备的碲酸盐玻璃具有很好的热稳定性,玻璃析晶温度Tx与玻璃转变温度Tg之差(ΔT=Tx-Tg)达到了185 ℃,高于其它文献的报道|同时,Ce3+离子共掺引入的能量转移(Ce³⁺∶2F5/2+Er³⁺∶4I11/2→Ce³⁺∶2F7/2+Er³⁺∶4I13/2)有效地抑制了Er³⁺离子上转换发光并显著增强了1.53 μm波段荧光强度,而发射截面随着Ce³⁺离子掺杂浓度相应增大.优异的热稳定性以及光谱性能揭示Er³⁺/Ce³⁺共掺碲酸盐玻璃是一种潜在的制备宽带掺铒光纤放大器的理想增益介质.     

纳米晶ZrO2:Er3+-Yb3+的制备及其室温上转换发射

用化学共沉淀法制备了ZrO₂:Er³⁺-Yb³⁺纳米晶粉体，所制备的纳米晶粉体具有较强的室温上转换发射和红外发射.研究了样品的晶体结构和上转换发光性质随着Yb³⁺掺杂浓度和煅烧温度的变化关系.通过X射线衍射谱分析发现，经800℃煅烧2h后得到的ZrO₂:Er³⁺-Yb³⁺纳米晶是四方相和单斜相的混合结构，经950℃煅烧2h后得到的样品以单斜相为主，随着Y     

Biomimetic synthesis of HgS nanoparticles in the bovine serum albumin solution

HgS nanocrystals conjugated with protein were synthesized in aqueous solution of Bovine Serum Albumin (BSA) at room temperature. The obtained HgS nanoparticles with average diameter about 20–40 nm were characterized by powder X-ray diffraction (XRD), transmission electron microscopy (TEM), selected-area electron diffraction (SAED) and high-resolution transmission electron microscopy (HRTEM). The quantum-confined effect of the HgS nanoparticles is confirmed by the ultraviolet-visible (UV-vis) and photoluminescence (PL) spectrum. The rescults indicate that the BSA not only induce the nucleation, but inhibit the further growth of HgS nanoparticles. The effect of Hg²⁺ on BSA and the change of BSA conformation were studied through Fourier transform infrared (FTIR) spectroscopy and Circular dichroism (CD) spectroscopy. The possible mechanism of HgS nanoparticles growth in the BSA solution was also discussed.     

Upconversion emission enhancement in Er/Yb-codoped BaTiO3 nanocrystals by tridoping with Li ions

Er³⁺/Yb³⁺/Li⁺-tridoped BaTiO₃ nanocrystals were prepared by a sol-gel method to improve the upconversion (UC) luminescence of rare-earth doped BaTiO₃ nanoparticles. Effects of Li⁺ ion on the UC emission properties of the Er³⁺/Yb³⁺/Li⁺-tridoped BaTiO₃ nanocrystals were investigated. The results indicated that tridoping with Li⁺ ion enhanced the visible green and red UC emissions of Er³⁺/Yb³⁺-codoped BaTiO₃ nanocrystals under the excitation of a 976 nm laser diode. X-ray diffraction and decay time of the UC luminescence were studied to explain the reasons of the enhancement of UC emission intensity. X-ray diffraction results gave evidence that tridoping with Li⁺ ion decreased the local symmetry of crystal field around Er³⁺, which increased the intra-4f transitions of Er³⁺ ion. Moreover, lifetimes in the intermediate ⁴ S_3/2 and ⁴I_11/2 (Er) states were enhanced by Li⁺ ion incorporation in the lattice. Therefore, it can be concluded that Li⁺ ion in rare-earth doped nanocrystals is effective in enhancing the UC emission intensity.     

发光二极管用红色荧光粉Sr0.8-xBaxEu0.2WO4的制备和性质研究

采用化学共沉淀法制备了不同Ba²⁺掺杂浓度、 不同煅烧温度的Sr_0.8-xBa_xEu_0.2WO₄红色荧光粉. 研究了样品的晶体取向和晶格 畸变对发光性质的影响, 实验结果表明: 合成的Sr_0.8-xBa_xEu_0.2WO₄红色荧光粉为四方相, 样品中Eu³⁺的⁵D₀–⁷F₂跃迁的红光能被近紫外光和蓝光有效激发. 适量的Ba²⁺离子取代部分的Sr²⁺提高了Sr_0.8Eu_0.2WO₄荧光粉的发光强度, Ba²⁺掺杂浓度的改变对基质的晶格参数、晶体对称性和发光性能影响较大, Ba²⁺的最佳掺杂量为30%.     

Luminescent properties of stabled hexagonal phase Sr1−xBaxAl2O4:Eu (x=0.37-0.70)

Stabled hexagonal phase Sr_1−xBa_xAl₂O₄:Eu²⁺ (x=0.37-0.70) was prepared by solid-state method. Result revealed that the structure behavior of the SrAl₂O₄:Eu²⁺ calcined at 1350 °C in a reducing atmosphere for 5 h strongly depended on the Ba²⁺ concentration. With increasing Ba²⁺ concentration, a characteristic hexagonal phase can be observed. When 37-70% of the strontium is replaced by barium, the structure of the prepared sample is pure hexagonal. Photoluminescence and excitation spectra of the samples with different x and doped with 2% Eu²⁺ were investigated. Changes in the emission spectra were observed in the two different phases. The green emission at 505 nm from Eu²⁺ was found to be quite strong in the hexagonal phase. The intensity and peak position of the green luminescence from Eu²⁺ changed with increasing content of Ba²⁺. The strongest green emission was obtained from Sr_0.61Ba_0.37Al₂O₄:Eu²⁺. The decay characteristics of Sr_1−xBa_xAl₂O₄:Eu²⁺ (x=0.37-0.70) showed that the life times also varied with the value of x. Furthermore, the emission colors and decay times varying with x could be ascribed to the variation of crystal lattice.     

Luminescence properties and mechanism of Zn1.92−xBaxSi1−yTiyO4:0.08Mn phosphors in VUV region

The present commercial phosphor Zn₂SiO₄:Mn²⁺ requires further improvement because of its long decay time. In this work, the co-doping effects of Ba²⁺ and Ti⁴⁺ upon emission intensity and decay time were investigated. Ba²⁺ and Ti⁴⁺ cations have favorable influences on the photoluminescent properties. When doped with appropriate amount of Ba²⁺, the intensity of green emission was increased 12% and the decay time was shortened 18%. When doped with appropriate amount of Ti⁴⁺, the luminescence intensity was enhanced a little, and the decay time was shortened 14%. Ba²⁺ and Ti⁴⁺ were co-doped in Zn₂SiO₄:Mn²⁺ system, the luminescence intensity was enhanced 18%, and the decay time was shortened sharply (about 31%).     

Synthesis and luminous characteristics of Ba2MgSi2−xAlxO7: 0.1Eu, 0.1Mn phosphor for WLED

The shift of the emission band to longer wavelength (yellow-orange) of the Ba₂MgSi_2−xAl_xO₇: 0.1Eu²⁺ phosphor under the 350-450 nm excitation range has been achieved by adding the codoping element (Mn²⁺) in the host. The single-host silicate phosphor for WLED, Ba₂MgSi_2−xAl_xO₇: 0.1Eu²⁺, 0.1Mn²⁺ was prepared by high-temperature solid-state reaction. It was found experimentally that, its three-color emission peaks are situated at 623, 501 and 438 nm, respectively, under excitation of 350-450 nm irradiation. The emission peaks at 438 and 501 nm originate from the transition 5d to 4f of Eu²⁺ ions that occupy the two Ba²⁺ sites in the crystal of Ba₂MgSi_2−x Al_xO₇, while the 623 nm emission is attributed to the energy transfer from Eu²⁺ ions to Mn²⁺ ions. The white light can be obtained by mixing the three emission colors of blue (438 nm), green (501 nm) and red (623 nm) in the single host. When the concentrations of the Al³⁺, Eu²⁺ and Mn²⁺ ions were 0.4, 0.1 and 0.1 mol, respectively, the sample presented intense white emission. The addition of Al ion to the host leads to a substantial change of intensity ratio between blue and green emissions. White light could be obtained by combining this phosphor with 405 nm light-emitting diodes. The near-ultraviolet GaN-based Ba₂MgSi_1.7 Al_0.3O₇: 0.1Eu²⁺, 0.1Mn²⁺ LED achieves good color rendering of over 85.     

The luminescence enhancement of Eu3+ ion and SnO2 nanocrystal co-doped solben gel SiO2 films

SnO₂ nanocrystal and rare-earth Eu³⁺ ion co-doped SiO₂ thin films are prepared by sol-gel and spin coating methods. The formation of tetragonal rutile structure SnO₂ nanocrystals with a uniform distribution is confirmed by X-ray diffraction and transmission electron microscopy. Fourier transform infrared spectroscopy is used to investigate the densities of the hydroxyl groups, and it is found that the emission intensity from the ⁵D₀-⁷F₂ transitions of the Eu³⁺ ions is enhanced by two orders of magnitude due to energy transfer from the oxygen-vacancy-related defects of the SnO₂ nanocrystals to nearby Eu³⁺ ions. The influences of the amounts of Sn and the post-annealing temperatures are systematically evaluated to further understand the mechanism of energy transfer. The luminescence intensity ratio of Eu³⁺ ions from electric dipole transition and magnetic dipole transition indicate the different probable locations of Eu³⁺ ions in the sol-gel thin film, which are further discussed based on temperature-dependent photoluminescence measurements.     

Luminescence enhancement by energy transfer from Ce ions in Ba1.6Ca0.4P2O7:Ce:Tb phosphor

The optical properties of Ba_1.6Ca_0.4P₂O₇ doped with Ce³⁺ and Tb³⁺ are investigated. Under excitation at 280 nm the emission spectrum of Ba_1.6Ca_0.4P₂O₇:Ce³⁺ consists of a peak at 370 nm and a shoulder at the longer wavelength side. The emission spectra of Ba_1.6Ca_0.4P₂O₇:Tb³⁺ shows the well-known emission lines due to ⁵D₄-⁷F_J transitions of Tb³⁺. The green emissions of Tb³⁺ ions are enhanced upon UV excitation through energy transfer from Ce³⁺ to Tb³⁺ ions. The efficiency of such an energy transfer is estimated based on spectroscopic data. The dependence of photoluminescence (PL) intensities of Ce³⁺ and Tb³⁺ emissions on Ce³⁺ or Tb³⁺ concentrations in the systems (Ba_1.6Ca_0.4P₂O₇:0.04Ce³⁺,xTb³⁺ and Ba_1.6Ca_0.4P₂O₇:xCe³⁺,0.04Tb³⁺) and the temperature dependence of PL emission spectra of Ba_1.6Ca_0.4P₂O₇:0.06Ce³⁺,0.04Tb³⁺ is also investigated.     

Fluorescence emission spectrum and energy transfer in Eu and Mn co-doped Ba2Ca(BO3)2 phosphors

Eu²⁺ and Mn²⁺ co-doped Ba₂Ca(BO₃)₂ phosphors yield two emission bands consisting of green and red components under the excitation of 360 nm, which shows a great potential for white LEDs. Effective energy transfer occurs in Eu²⁺/Mn²⁺ co-doped Ba₂Ca(BO₃)₂ host due to the large spectral overlap between the emission of Eu²⁺ and the excitation of Mn²⁺. The energy transfer from Eu²⁺ to Mn²⁺ is thoroughly investigated by their excitation, emission and photoluminescence decay behaviors, and is demonstrated to be via the dipole–quadrupole interaction.     

Optical properties of nanocrystalline-coated Y2O3:Er, Yb obtained by mechano-chemical and combustion synthesis

Y₂O₃:Er³⁺, Yb³⁺ nanocrystals have been obtained by ball milling and using a combustion synthesis procedure. In both cases the nanocrystals have been successfully coated with SiO₂ following the Stöber method. The average size of the as-synthesized nanoparticles has been estimated from X-ray diffraction patterns and transmission electron microscopy images. The dependence of the optical properties of these samples on synthesis procedure or dopant concentration has been investigated. Emission, excitation and lifetime measurements have been carried out. Upconversion luminescence has been detected in all samples and an enhancement of the red to green emission ratio has been observed in all samples after infrared compared to visible excitation. The mechanisms responsible for the upconversion phenomena have been discussed.