Hydrogen production from the methanolysis of ammonia borane by Pd-Co/Al2O3 coated monolithic catalyst

The aim of this study is to enable high hydrogen production yield from catalytic methanolysis of ammonia borane (AB) in the presence of a cordierite type ceramic monolithic. The monolithic channel surfaces were coated with Al₂O₃ by wash-coating method and then this layer was impregnated with 1 wt%Pd-2 wt%Co bimetallic catalyst. SEM-EDX and multi-point BET analysis were used in order to characterize the catalyst. The experimental studies were conducted in a continuous flow type reactor, which was used for the first time in this study. The reactions were carried on low temperature (40 °C), and with various AB feed concentrations and flow rates. It was found that the highest hydrogen production yield (88.5%) was obtained from AB flow rate of 3.3 mL/min, and AB feed concentration of 0.1 wt%. It was concluded that Pd-Co/Al₂O₃ coated monolithic, which is a stable, active and low-cost catalyst, was a very promising catalyst for on-board hydrogen production from the methanolysis of ammonia borane.     

Hydrogen release by thermolysis of ammonia borane NH3BH3 and then hydrolysis of its by-product [BNHx]

Ammonia borane (AB) is one of the most attractive hydrides owing to its high hydrogen density (19.5 wt%). Stored hydrogen can be released by thermolysis or catalyzed hydrolysis, both routes having advantages and issues. The present study has envisaged for the first time the combination of thermolysis and hydrolysis, AB being first thermolyzed and then the solid by-product believed to be polyaminoborane [NH₂BH₂]_n (PAB) being hydrolyzed. Herein we report that: (i) the combination is feasible, (ii) PAB hydrolyzes in the presence of a metal catalyst (Ru) at 40 °C, (iii) a total of 3 equiv. H₂ is released from AB and PAB-H₂O, (iv) high hydrogen generation rates can be obtained through hydrolysis, and (v) the by-products stemming from the PAB hydrolysis are ammonium borates. The following reactions may be proposed: AB → PAB + H₂ and PAB + xH₂O → 2H₂ + ammonium borates. All of these aspects as well as the advantages and issues of the combination of AB thermolysis and PAB hydrolysis are discussed.     

Hydrogen production from hydrolysis of ammonia borane with limited water supply

Effect of limited water supply to hydrolysis of ammonia borane for hydrogen evolution is studied over the cases in which the initial molar ratio of water to ammonia borane (H₂O/AB) is set at 1.28, 2.57 and 4.50. The conversion efficiency of ammonia borane to hydrogen is estimated from the accumulated volume of produced hydrogen gas and the quantitative analysis of hydrolysate by solid-state ¹¹B NMR. Characteristics of hydrogen evolution are significantly influenced by both water dosage and injection rate of water. In the case that water is a limiting agent, namely, H₂O/AB = 1.28, less hydrogen is produced than that predicted stoichiometrically. In contrast, conversion efficiency of ammonia borane reaches nearly 100% for the case with H₂O/AB = 4.50. Injection rate of water to ammonia borane also affect profoundly the produced volume and production rate of hydrogen, if water is used as a limiting agent in the hydrolysis of ammonia borane. Nonetheless, boric acid and metaboric acid are found to be the dominant products in the hydrolysate from XRD, FT-IR and solid-state ¹¹B NMR analysis. The hydrogen storage capacity using limited water supply in this work could reach as high as about 5.33 wt%, based on combined mass of reactants and catalyst.     

Efficient and highly rapid hydrogen release from ball-milled 3NH3BH3/MMgH3 (M = Na,K, Rb) mixtures at low temperatures

The stoichiometric reactions of ammonia borane (NH₃BH₃, AB) and selected alkali or alkaline-earth metal hydrides produce metal amidoboranes, which possess dehydrogenation property advantages over their parent AB. However, the losses of hydrogen capacity and chemical energy in the preparation process make metal amidoboranes less energy-effective for hydrogen storage application. In the present study, by combining the M⁺–Mg²⁺ double cations remarkably lowers the reactivity of the alkali metal hydrides toward AB. As a result, the starting Mg-based ternary hydrides MMgH₃ (M = Na, K, Rb) and AB phases are largely stable in the mechanical milling process, but transform to the corresponding mixed-cation amidoboranes in the subsequent heating process. Importantly, when the post-milled 3AB/MMgH₃ mixtures are isothermally heated at above 60 °C using water bath, the formation and decomposition processes of the mixed-cation amidoboranes can be favorably combined, giving rise to rapid and efficient dehydrogenation performances at the mild temperatures (60–80 °C). The results acquired may provide a generalized reactions coupling strategy for designing and synthesis other potentially efficient hydrogen storage system.     

Hydrogen permeation through a Pd-based membrane and RWGS conversion in H2/CO2, H2/N2/CO2 and H2/H2O/CO2 mixtures

This study investigated the effect of gases such as CO₂, N₂, H₂O on hydrogen permeation through a Pd-based membrane −0.012 m² – in a bench-scale reactor. Different mixtures were chosen of H₂/CO₂, H₂/N₂/CO₂ and H₂/H₂O/CO₂ at temperatures of 593–723 K and a hydrogen partial pressure of 150 kPa. Operating conditions were determined to minimize H₂ loss due to the reverse water gas shift (RWGS) reaction. It was found that the feed flow rate had an important effect on hydrogen recovery (HR). Furthermore, an identification of the inhibition factors to permeability was determined. Additionally, under the selected conditions, the maximum hydrogen permeation was determined in pure H₂ and the H₂/CO₂ mixtures. The best operating conditions to separate hydrogen from the mixtures were identified.     

Structural transformation of layered hydrogen trititanate (H2Ti3O7) to TiO2(B) and its electrochemical profile for lithium-ion intercalation

The thermally-induced structural transformation of layered hydrogen trititanate (H₂Ti₃O₇) to TiO₂(B) has been systematically studied by means of in situ X-ray diffraction (XRD) over a wide temperature range from 170 to 450 °C. Our data indicate a structural transition realized via continuous loss of interlayer water, which results in a series of non-stoichiometric hydrogen titanate compounds (3TiO₂·δH₂O). Electrochemical analysis of hydrogen titanates for lithium-ion intercalation shows that reversible specific capacity increases as calcination temperature increases, whereas cycling stability decreases during the continuous dehydration process.     

Synergistic effect of Cu2O/TiO2 heterostructure nanoparticle and its high H2 evolution activity

Cu₂O/TiO₂ nanoparticles were prepared by solvothermal method, which formed the heterostructure of Cu₂O/TiO₂. Due to the heterostructure, the H₂ evolution rate under simulated solar irradiation was increasingly promoted. Meanwhile a certain amount of Cu particles which were confirmed by Transmission Electro Microscopy (TEM) and X-Ray Photoelectron Spectroscopy (XPS), formed on the surface of Cu₂O/TiO₂, and the photoactivity was accordingly further enhanced. The stabilized activity was maintained after many times irradiation. It is interesting that after a few hours irradiation the amount of Cu particles on the surface kept unchanged in the presence of Cu₂O and TiO₂. The Cu particles that formed during hydrogen generation reaction play a key role in the further enhancement of the hydrogen production activity. In this study, it is the first time to study the details on the formation of the stable ternary structure under simulated solar irradiation and their synergistic effect on the photoactivity of the water splitting.     

Electrospun nickel doped titanium dioxide nanofibers as an effective photocatalyst for the hydrolytic dehydrogenation of ammonia borane

In this study, Ni-doped titanium dioxide (TiO₂) electrospun nanofibers are introduced as novel material for dehydrogenation of ammonia borane (AB) complex. Hydrolysis experiments with introduced catalytic nanofibers are prevailed to rapidly release hydrogen from AB complex. Typically, Ni nanoparticles (NPs) behave as a catalyst, meanwhile the incorporation of nickel NPs lead to decrease in the electrons/holes recombination rate in TiO₂ which resulted in the increase of active ions in the solution to a rapid evolution of hydrogen gas at room temperature. The utilized physiochemical analyses indicate that the introduced Ni-doped TiO₂ nanofibers have a smooth surface and uniform diameters along their lengths. Under sunlight irradiation, the hydrogen production rate in case of utilizing Ni-doped TiO₂ nanofibers is rapidly increased compared to the pristine TiO₂ nanofibers, the maximum hydrogen equivalent in case of the doped nanofibers is 2.6 while the pristine one is 1.4. Both formulations exhibit almost equal low activity in daylight as the observed hydrogen equivalent is 0.4. Overall, this study proposes cheap, stable and effective material for AB dehydrogenation at room temperature.     

Hot-pressed Li0.33La0.57TiO3

The electrical and mechanical properties of hot-pressed versus sintered Li_0.33La_0.57TiO₃ at temperature of 1050 °C were investigated. It was observed that hot-pressed Li_0.33La_0.57TiO₃ exhibited a higher total Li-ion conductivity (∼20×) and hardness (∼11×) compared to sintered Li_0.33La_0.57TiO₃ as a result of its higher density. Hot-pressed Li_0.33La_0.57TiO₃ had a similar relative density and total Li-ion conductivity when compared to Li_0.33La_0.57TiO₃ sintered at 1250 °C, where significant Li₂O loss occurs. These results suggest that hot-pressing can be used as a consolidation method to reduce Li₂O loss to obtain dense Li_0.33La_0.57TiO₃.     

Ultrasonic spray pyrolysis synthesis of Ag/TiO2 nanocomposite photocatalysts for simultaneous H2 production and CO2 reduction

Simultaneous photocatalytic hydrogen production and CO₂ reduction (to form CO and CH₄) from water using methanol as a hole scavenger were investigated using silver-modified TiO₂ (Ag/TiO₂) nanocomposite catalysts. A simple ultrasonic spray pyrolysis (SP) method was used to prepare mesoporous Ag/TiO₂ composite particles using TiO₂ (P25) and AgNO₃ as the precursors. The material properties and photocatalytic activities were compared with those prepared by a conventional wet-impregnation (WI) method. It was found that the samples prepared by the SP method had a larger specific surface area and a better dispersion of Ag nanoparticles on TiO₂ than those prepared by the WI method, and as a result, the SP samples showed much higher photocatalytic activities toward H₂ production and CO₂ reduction. The optimal Ag concentration on TiO₂ was found to be 2 wt%. The H₂ production rate of the 2% Ag/TiO₂–SP sample exhibited a six-fold enhancement compared with the 2% Ag/TiO₂–WI sample and a sixty-fold enhancement compared with bare TiO₂. The molar ratio of H₂ and CO in the final products can be tuned in the range from 2 to 10 by varying the reaction gas composition, suggesting a viable way of producing syngas (a mixture of H₂ and CO) from CO₂ and water using the prepared Ag/TiO₂ catalysts with energy input from the sun.     

Photocatalytic hydrogen production from aqueous methanol solution with CuO/Al2O3/TiO2 nanocomposite

The photocatalytic hydrogen production from aqueous methanol solution was investigated with ZnO/TiO₂, SnO/TiO₂, CuO/TiO₂, Al₂O₃/TiO₂ and CuO/Al₂O₃/TiO₂ nanocomposites. A mechanical mixing method, followed by the solid-state reaction at elevated temperature, was used for the preparation of nanocomposite photocatalyst. Among these nanocomposite photocatalysts, the maximal photocatalytic hydrogen production was observed with CuO/Al₂O₃/TiO₂ nanocomposites. A variety of components of CuO/Al₂O₃/TiO₂ photocatalysts were tested for the enhancement of H₂ formation. The optimal component was 0.2 wt% CuO/0.3 wt% Al₂O₃/TiO₂. The activity exhibited approximately tenfold enhancement at the optimum loading, compared with that with pure P-25 TiO₂. Nano-sized TiO₂ photocatalytic hydrogen technology has great potential for low-cost, environmentally friendly solar-hydrogen production to support the future hydrogen economy.     

Noncatalytic hydrothermolysis of ammonia borane

Hydrolysis of ammonia borane (AB) is attractive as a chemical method for hydrogen storage. The use of catalysts is, however, usually required. In the present paper, two new methods for releasing hydrogen from AB and water are investigated which do not involve any catalyst. One method is based on combustion of AB mixtures with nanoscale aluminum powder and gelled water. It is shown experimentally that these mixtures, upon ignition, exhibit self-sustained combustion with hydrogen release from both AB and water. The other method involves external heating of aqueous AB solutions to temperatures 120 °C or higher, under argon pressure to avoid water boiling. To clarify the reaction mechanism, isotopic experiments using D₂O instead of H₂O were conducted. It is shown that heating AB/D₂O solution to temperatures 117–170 °C releases 3 equiv. of hydrogen per mole AB, where 2–2.1 equiv. originate from AB and 0.9–1 equiv. from water. The prospects of both methods for hydrogen storage are discussed.     

Experimental and numerical investigation of low-pressure laminar premixed synthetic natural gas/O2/N2 and natural gas/H2/O2/N2 flames

The oxidation of laminar premixed natural gas flames has been studied experimentally and computationally with variable mole fractions of hydrogen (0, 20, and 60%) present in the fuel mixture. All flames were operated at low pressure (0.079 atm) and at variable overall equivalence ratios (0.74<?<1.0) with constant cold gas velocity. At the same global equivalence ratio, there is no significant effect of the replacement of natural gas by 20% of H₂. The small differences recorded for the intermediate species and combustion products are directly due to the decrease of the amount of initial carbon. However, in 60% H₂ flame, the reduction of hydrocarbon species is due both to kinetic effects and to the decrease of initial carbon mole fraction. The investigation of natural gas and natural gas/hydrogen flames at similar C/O enabled identification of the real effects of hydrogen. It was shown that the presence of hydrogen under lean conditions activated the H-abstraction reactions with H atoms rather than OH and O, as is customary in rich flames of neat hydrocarbons. It was also demonstrated that the presence of H₂ favors CO formation.     

Enhanced hydrogen generation from methanol aqueous solutions over Pt/MoO3/TiO2 under ultraviolet light

The photocatalytic activity in hydrogen production from methanol reforming can be significantly enhanced by Pt/MoO₃/TiO₂ photocatalysts. Compared with Pt/P25, the photocatalytic activity of optimized Pt/MoO₃/TiO₂ shows an evolution rate of 169 μmol/h/g of hydrogen, which is almost two times higher than that of Pt/P25. XRD and Raman spectra show that MoO₃ are formed on the surface of TiO₂. It is found that with the bulk MoO₃ just formed, the catalyst shows the highest activity due to a large amount of heterojunctions and the high crystallinity of MoO₃. The HRTEM image showed a close contact between MoO₃ and TiO₂. It is proposed that the Z-scheme type of heterojunction between MoO₃ and TiO₂ is responsible for the improved photocatalytic activity. The heterojunction structure of MoO₃/TiO₂ does not only promote the charge separation, but also separates the reaction sites, where the oxidation (mainly on MoO₃) and reduction (on TiO₂) reactions occurred.     

TiO2 nanotubes for hydrogen generation by photocatalytic water splitting in a two-compartment photoelectrochemical cell

Highly ordered TiO₂ nanotube arrays for hydrogen production have been synthesized by electrochemical anodization of titanium sheets. Under solar light irradiation, hydrogen generation by photocatalytic water splitting was carried out in the two-compartment photoelectrochemical cell without any external applied voltage. The hydrogen gas and oxygen generated on Pt side and on TiO₂ nanotubes side respectively were efficiently separated. The effect of anodization time on the morphology structures, photoelectrochemical properties and hydrogen production was systematically investigated. Due to more charge carrier generation and faster charge transfer, a maximum photoconversion efficiency of 4.13% and highest hydrogen production rate of 97 μmol h⁻¹cm⁻² (2.32 mL h⁻¹cm⁻²) were obtained from TiO₂ nanotubes anodized for 60 min.     

Understanding the effect of TiO2, VCl3, and HfCl4 on hydrogen desorption/absorption of NaAlH4

The main objective of this work was to investigate the different effects of transition metals (TiO₂, VCl₃, HfCl₄) on the hydrogen desorption/absorption of NaAlH₄. The HfCl₄ doped NaAlH₄ showed the lowest temperature of the first desorption at 85 °C, while the one doped with VCl₃ or TiO₂ desorbed at 135 °C and 155 °C, respectively. Interestingly, the temperature of desorption in subsequent cycles of the NaAlH₄ doped with TiO₂ reduced to 140 °C. On the contrary, in the case of NaAlH₄ doped with HfCl₄ or VCl₃, the temperature of desorption increased to 150 °C and 175 °C, respectively. This may be because Ti can disperse in NaAlH₄ better than Hf and V; therefore, this affected segregation of the sample after the desorption. The maximum hydrogen absorption capacity can be restored up to 3.5 wt% by doping with TiO₂, while the amount of restored hydrogen was lower for HfCl₄ and VCl₃ doped samples. XRD analysis demonstrated that no Ti-compound was observed for the TiO₂ doped samples. In contrast, there was evidence of Al–V alloy in the VCl₃ doped sample and Al–Hf alloy in the HfCl₄ doped sample after subsequent desorption/absorption. As a result, the V- or Hf-doped NaAlH₄ showed the lower ability to reabsorb hydrogen and required higher temperature in the subsequent desorptions.     

Improvement in desorption kinetics of NaAlH4 catalyzed with TiO2 nanopowder

NaAlH₄ has been homogeneously mixed with micron- and nano-sized TiO₂ powders by high-energy ball milling and their sorption properties have been investigated during hydrogen absorption/desorption cycles. NaAlH₄ with TiO₂ nanopowder exhibits as good desorption kinetics as NaAlH₄ with TiCl₃, whereas poor desorption kinetics is observed with micron-sized TiO₂ powder. NaAlH₄ with TiO₂ nanopowder also provides improved cyclic property compared to NaAlH₄ with TiCl₃ in terms of both desorption rate and hydrogen capacity. X-ray diffraction analysis shows that micron-sized TiO₂ remains stable with NaAlH₄ after milling, although thermodynamic calculation predicts that TiO₂ reacts with NaAlH₄.     

Significantly improved dehydrogenation of LiAlH4 catalysed with TiO2 nanopowder

The effects of TiO₂ nanopowder addition on the dehydrogenation behaviour of LiAlH₄ have been studied. The 5 wt.% TiO₂-added LiAlH₄ sample showed a significant improvement in dehydrogenation rate compared to that of undoped LiAlH₄, with the dehydrogenation temperature reduced from 150 °C to 60 °C. Kinetic desorption results show that the added LiAlH₄ released about 5.2 wt% hydrogen within 30 min at 100 °C, while the as-received LiAlH₄ just released below 0.2 wt.% hydrogen within same time at 120 °C. From the Arrhenius plot of the hydrogen desorption kinetics, the apparent activation energy is 114 kJ/mol for pure LiAlH₄ and 49 kJ/mol for the 5 wt.% TiO₂ added LiAlH₄, indicating that TiO₂ nanopowder adding significantly decreased the activation energy for hydrogen desorption of LiAlH₄. X-ray diffraction and Fourier transform infrared analysis show that there is no phase change in the cell volume or on the Al-H bonds of the LiAlH₄ due to admixture of TiO₂ after milling. X-ray photoelectron spectroscopy results show no changes in the Ti 2p spectra for TiO₂ after milling and after dehydrogenation. The improved dehydrogenation behaviour of LiAlH₄ in the presence of TiO₂ is believed to be due to the high defect density introduced at the surfaces of the TiO₂ particles during the milling process.     

High photocatalytic hydrogen production over the band gap-tuned urchin-like Bi2S3-loaded TiO2 composites system

A new system using Bi₂S₃-loaded TiO₂ photocatalysts (Bi₂S₃/TiO₂) was developed to enhance the production of hydrogen. The Bi₂S₃ (5, 10, 15 wt%) particles in an urchin-like morphology with a length of about 2∼3 μm and a diameter of 15–20 nm, which can absorb all wavelengths in UV–visible radiation, were prepared by solvothermal method and loaded onto nano-sized TiO₂ (10∼15 nm) for photocatalysis on hydrogen production. The evolution of H₂ from methanol/water (1:1) photo splitting over the Bi₂S₃/TiO₂ composite in the liquid system was enhanced, compared with that over pure TiO₂ and Bi₂S₃. In particular, 14.2 ml of H₂ gas was produced after 12 h when 0.5 g of a 10 wt% Bi₂S₃/TiO₂ composite was used. On the basis of cyclic voltammetry (CV) results, the high photoactivity was attributed to the increase of band gap in the Bi₂S₃/TiO₂ composite, due to the decreased recombination between the excited electrons and holes.     

Cobalt doped TiO2: A stable and efficient photocatalyst for continuous hydrogen production from glycerol: Water mixtures under solar light irradiation

Glycerol is the main by-product during the trans-esterification of vegetable oils to biodiesel. In this study, we investigate the process of photocatalytic hydrogen production from glycerol aqueous solution, with the use of cobalt doped TiO₂ photocatalyst under solar light irradiation. Cobalt doped TiO₂ photocatalysts are prepared by impregnation method and these catalysts are characterized by XRD, EDAX, DRS, TEM, EPR and XPS techniques. DRS studies clearly show the expanded photo response of TiO₂ into visible region on impregnation of Co²⁺ ions on surface of TiO₂. XPS studies also show change in the binding energy values of O1s, Ti 2p and Co 2p, indicating that Co²⁺ ions are in interaction with TiO₂. Maximum hydrogen production of 220 μ mol h⁻¹ g⁻¹ is observed on 2 wt% cobalt doped TiO₂ catalysts in pure water under solar irradiation. A significant improvement in hydrogen production is observed in glycerol: water mixtures; and maximum hydrogen production of 11,021 μ mol h⁻¹ g⁻¹ is obtained over 1 wt% cobalt doped TiO₂ in 5% glycerol aqueous solutions. Furthermore, to evaluate some reaction parameters such as cobalt wt% on TiO₂, glycerol concentration, substrate effect (alcohols) and pH of the solution on the hydrogen production activity are systematically investigated. When the catalysts are examined under UV irradiation, a 3–4 fold increase in activity is observed where this activity seems to decrease with time; however, a continuous activity is observed under solar irradiation on these catalysts. The decreased activity could be ascribed the loss of cobalt ions under UV irradiation, as evidenced by EDAX and TEM analysis. A possible explanation for the stable and continuous activity of cobalt doped TiO₂ photocatalysts under solar irradiation is proposed.