激光悬浮区熔定向凝固Al2O3/YAG/ZrO2三元过共晶合金的微观组织

利用自行研制的激光悬浮区熔设备制备了Al₂O₃/YAG/ZrO₂三元过共晶自生复合材料.在过共晶成分下获得了不含初生相的全共晶层片状组织.详细分析了固/液界面形貌形成原因,并由界面形貌出发阐述了Al₂O₃/YAG/ZrO₂三元过共晶组织织构化趋势.结果表明,低凝固速率下,三元过共晶成分下层片间距大于三元共晶成分下层片间距,而在高凝固速率下则相反,这主要是由于ZrO₂的加入影响了体系的传热及传质条件,通过经典非规则共晶模型综合分析了传输条件对层片间距的影响.过共晶平均层片间距(λ_av)与凝固速率（V）满足λ_avV^0.5=14.7μm^1.5·s^-0.5,符合JH模型.对于激光加工中经常出现的带状组织形成机理也进行了讨论.     

Lu2O3/TiO2/Nb2O5共稳定ZrO2热障涂层材料研究

采用Lu2O3/TiO2/Nb2O5作为ZrO2热障涂层材料的稳定剂,研究Lu2O3/TiO2/Nb2O5共稳定ZrO2(15%LTNSZ)热障涂层材料在900℃、40 mol%V2O5+60 mol%Na2SO4熔盐中的热腐蚀行为。结果表明:8%YSZ热障涂层材料热腐蚀2 h后,t相ZrO2全部相变为m相ZrO2,热腐蚀产物为尺寸较大的YVO4晶体;15%LTNSZ热障涂层材料热腐蚀20 h后,m相ZrO2的比例仅为5.5%,热腐蚀产物为尺寸较小的LuVO4晶体。与Y2O3稳定剂相比,Lu2O3/TiO2/Nb2O5稳定剂使ZrO2在40 mol%V2O5+60 mol%Na2SO4熔盐中的抗热腐蚀性能提高1个量级以上。     

CeO2对Al2O3基陶瓷涂层耐蚀性的影响

通过优化Al2O3基陶瓷涂层配方和工艺,并加入适量的稀土氧化物CeO2,对陶瓷涂层的界面形貌、组织结构、结合力和耐蚀性进行了研究。结果表明,添加适量的稀土氧化物CeO2,使Al2O3基陶瓷涂层致密性、结合力和耐蚀性得到提高。     

Y2O3含量对大气等离子喷涂Al2O3-Y2O3复合涂层微观结构和力学性能的影响

目的 探究掺杂不同质量分数Y₂O₃对Al₂O₃-Y₂O₃复合涂层微观结构及其力学性能的影响。方法 采用大气等离子喷涂制备Al₂O₃涂层,以及Y₂O₃质量分数分别为10%、20%、30%、40%的Al₂O₃-Y₂O₃复合涂层。利用SEM、EDS对粉末以及不同涂层的形貌、组织结构、元素分布进行分析。使用XRD表征粉末和涂层的物相。使用显微硬度仪、纳米压痕测试仪和电子万能试验机对涂层的显微硬度、弹性模量以及断裂韧性等力学性能进行测试分析。结果 Al₂O₃喷涂粉末的物相由α-Al₂O₃组成,而喷涂得到的Al₂O₃涂层则由α-Al₂O     

Al2O3弥散强化316L不锈钢粉末的高速火焰喷涂

采用高能球磨工艺制备了Al2O3弥散强化316L不锈钢喷涂粉末,并进行高速火焰喷涂(HVOF)试验.研究了弥散强化粉末及其喷涂层的微观组织结构和硬度.采用销-盘磨损试验机测试了涂层的耐磨性能.结果表明,球磨加工后,Al2O3颗粒尺寸大多小于1 μm,由微米级、亚微米级及纳米级粒子组成并均匀分布在316L不锈钢基体粉末中.随着球磨时间的增加,粉末的显微硬度提高.喷涂后球磨粉末的微观组织结构基本不变,喷涂层的硬度比对应球磨粉末硬度低,其耐磨性明显优于单纯不锈钢粉末涂层.     

过渡材料对等离子喷涂Al2O3梯度陶瓷涂层性能影响

针对Al2O3陶瓷涂层结合强度低、孔隙率高的实际,选择NiAl金属间化合物和金属铜粉作为过渡材料,利用等离子喷涂制备Al2O3梯度陶瓷涂层,并对梯度涂层进行组织形貌观察,测试结合强度和孔隙率.结果表明,梯度涂层的组织表现出宏观的不均匀性和微观连续性的分布特征,NiAl和Cu是金属基体与Al2O3涂层之间过渡层的理想材料,可以有效地提高涂层的结合强度,而Cu-Al2O3梯度涂层又比NiAl-Al2O3梯度涂层结合强度高;梯度涂层的孔隙率远低于双涂层的孔隙率,在Cu-Al2O3梯度涂层中随Al2O3含量的增加,涂层的孔隙率降低,而且孔隙率低于NiAl-Al2O3梯度涂层.     

Al2O3颗粒直径对1 vol%的Al2O3/Cu基复合材料组织和性能的影响

采用粉末冶金法+热压工艺制备了不同Al₂O₃颗粒直径的1 vol%Al₂O₃/Cu基复合材料,使用光学显微镜和扫描电镜(SEM)观察了复合材料的显微组织,利用电子拉伸试验机测试了复合材料的力学性能。基于弹/塑性理论推导出了复合材料中颗粒周边的弹性区宽度的表达式。结果表明：Al₂O₃颗粒直径对Al₂O₃/Cu基复合材料强度及基体晶粒尺寸有着较大的影响;Al₂O₃颗粒直径越大,Al₂O₃/Cu基复合材料的抗拉强度、屈服强度越小;当Al₂O₃颗粒直径为5μm时,Al₂O₃/Cu基复合材料的抗拉强度和屈服强度分别为207和90 MPa,是铜试样的95.8%和95.7%。     

水环境中等离子喷涂纳米/微米喂料Al2O3/TiO2涂层的摩擦学行为

利用纳米结构和常规喂料用大气等离子喷涂方法制备了Al2O3/TiO2涂层,研究了水环境中两种涂层与不锈钢对磨时的摩擦磨损性能.结果表明：水环境中,两种涂层摩擦因数变化不大,但是纳米喂料涂层耐磨性能明显优于常规涂层,同时其对偶的磨损率仅为常规涂层对偶磨损率的1/3～1/5,磨损率随载荷的增加不断增加.讨论了水环境中两种涂层的磨损机制.     

不同基体对连续Al2O3f/Al复合材料纤维损伤的影响

采用真空气压浸渗法制备了增强体为Al₂O₃纤维,基体合金分别为1A99、ZL210A、ZL301及7075铝合金的连续Al₂O_3f/Al复合材料,并用NaOH溶液提取出Al₂O₃纤维,研究了不同基体对Al₂O_3f/Al复合材料纤维损伤的影响。结果表明,在同样的制备工艺下,不同的基体对Al₂O₃纤维的损伤程度不同。Al₂O₃纤维与纯铝及ZL210A基体界面反应程度微弱,纤维表面光滑,未发现界面反应产物,纤维剩余强度分别为1 746 MPa和1 658 MPa; Al₂O₃纤维与ZL301发生界面反应生成了MgAl₂O₄(镁铝尖晶石),纤维表面较为粗糙,剩余强度为1 584 MPa; Al₂O₃纤维与...     

CeO2掺杂对ZrO2-Y2O3纳米涂层性能的影响

在45钢基体表面等离子弧喷涂制备了掺杂不同含量CeO2纳米ZrO2涂层,运用XRD,SEM对涂层的组织结构进行了分析,测试了涂层的结合强度和显微硬度,考察了涂层与铝青铜对磨时的摩擦磨损性能．结果表明,CeO2增加了ZrO2涂层的致密性、结合强度和显微硬度．纳米ZrO2涂层中加入CeO2后,增加了ZrO2涂层／铝青铜摩擦副的摩擦系数,增强了纳米ZrO2涂层,耐磨能力．涂层与铝青铜对磨时,随着CeO2含量的增加,ZrO2涂层粘着磨损形式增强,而涂层脆性断裂脱落的趋势减轻．     

三元共晶成分Al2O3/YAG/ZrO2粉体及陶瓷的制备与组织性能研究

本文采用醇水共沉淀法制备了三元共晶成分Al₂O₃/YAG/ZrO₂粉体,在600-1350_oC温度范围煅烧后研究其物相转变过程。经1300_oC煅烧后Al₂O₃/YAG/ZrO₂共晶成分粉体的物相由α-Al₂O₃、c-ZrO₂和YAG构成,且具有α-Al₂O₃相包裹c-ZrO₂相的特殊结构。将煅烧粉体在1550_oC下热压烧结,制备具有内晶型结构的共晶成分Al₂O₃/YAG/ZrO₂复相陶瓷,其致密度、室温抗弯强度、断裂韧性和高温(1000_oC)抗弯强度分别为98.8%、420 MPa、3.69 MPa.m_1/2和464 MPa,并对复相陶瓷组织结构的形成机理进行了探讨。     

国外多孔基体氧化铝/氧化铝复合材料工程应用进展

氧化铝/氧化铝复合材料(Al2O3/Al2O3)是20世纪90年代兴起的一类连续陶瓷纤维增强陶瓷基复合材料,已经发展为与SiC/SiC、C/SiC等非氧化物陶瓷基复合材料并列的一类陶瓷基复合材料。与非氧化物陶瓷基复合材料相比,Al2O3/Al2O3具有长时抗氧化、高温耐腐蚀、低成本等独特优势,已经在航空发动机、地面燃气轮机等军民两用热结构材料领域展现出广阔的应用前景。本文从材料应用的角度出发,系统分析阐述了目前在Al2O3/Al2O3占主导地位的多孔基体Al2O3/Al2O3(P-Al2O3/Al2O3)的增韧机制、成型工艺和性能特点,重点归纳了国外近年来P-Al2O3/Al2O3的工程化应用进展及前景,最后指出了P-Al2O3/Al2O3存在的局限性并展望了未来发展方向,旨在为国内Al2O3/Al2O3体系发展提供借鉴和参考。     

CVD deposition and characterization of coloured Al2O3/ZrO2 multilayers

Coloured Al₂O₃/ZrO₂ multilayers have been deposited onto WC-Co based inserts by a CVD process. Through physical as well as optical analysis of such multilayers, colour is believed to originate from interference. The coatings are obtained with good process reproducibility. It was found that the ZrO₂ process used in the multilayer, with ZrCl₄ as the only metal chloride precursor, results in a mixture of tetragonal and monoclinic ZrO₂ phases. However by adding a relatively small amount of AlCl₃ during such a process results in ZrO₂ layers being composed of predominantly tetragonal ZrO₂ phase. Corresponding multilayers seem to have a more fine grained and smoother morphology whereas multilayers containing monoclinic ZrO₂ phase seem to be less perfect with existence of larger grains of ZrO₂ which are believed to scatter light and alter the reflectance of such a multilayer. In addition to this, such multilayers were found to be free of or with greatly reduced amount of thermal cracks, normally present in pure CVD grown Al₂O₃ layers.It is believed that, in the studied Al₂O₃/ZrO₂ multilayers, the observed tetragonal ZrO₂ phase is the result of a size effect, where small enough ZrO₂ crystallites energetically favor the tetragonal phase. However as the ZrO₂ crystallite size distribution is shifted to larger sizes it is believed that a mixture of crystallites with both stable and metastable tetragonal phases as well as a stable monoclinic phase is obtained. The proposed metastable tetragonal ZrO₂ phase may in fact explain the absence of thermal cracks in such multilayers through a transformation toughening mechanism, well known in ZrO₂ based ceramics.     

Cu+B复合钎料配比对Al2O3/TC4合金钎焊接头界面组织的影响

分别以不同配比的铜和硼混合粉末作为钎料,在钎焊温度930℃,保温时间10min条件下钎焊连接Al2O3与TC4合金,并结合SEM与EDS观察对钎焊接头的连接状况及组织结构进行分析．结果表明,A12O3／TC4合金钎焊接头的界面组织为Al2O3,／Ti3（Cu,A1）3O／Ti2Cu＋Ti2（Cu,Al）／Ti＋Ti2（Cu,Al）＋Ti（Cu,Al）＋AlCu2Ti＋Ti2Cu／Ti2Cu＋AICu：Ti＋TiB／Ti＋Ti2Cu／TC4合金．钎焊过程中,复合钎料中的铜与TC4合金中的钛发生互扩散,在连接层与TC4合金界面形成不同成分的Cu-Ti化合物．硼与液相中的钛反应,在接头中原位生成TiB晶须,且主要分布在Ti2Cu和AlCu2Ti上．随TiB生成量的增加,Ti2（Cu,Al）生成量增加,并逐渐变得连续,同时向Al2O3侧移动．     

预处理对阴极等离子电解沉积制备Al_2O_3涂层性能的影响

采用阴极等离子电解沉积法在镍基高温合金K418上制备Al_2O_3陶瓷层,为降低沉积过程中的电流密度,研究了950℃预处理对涂层微观组织、物相组成、力学性能及沉积过程中电流密度-电压曲线的影响。结果表明:预处理对涂层的表面、截面形貌和物相组成没有明显影响。当预处理时间延长至300 min,涂层抗超声振荡性能和抗热冲击性能分别提高了106.36%和90.13%。拉伸法测定涂层结合强度结果显示,经950℃预处理30 min的试样结合力可由未经预处理时的24.60 MPa提高至37.32 MPa。这些特性主要归因于预制氧化膜使合金基体表面导电性下降,有效地将电流密度-电压曲线第一个峰值由未经预处理的1.84 A/cm~2降至0.26 A/cm~2,同时氧化膜的存在为后续等离子放弧均匀化提供基础,从而提高了涂层与基体之间的结合力。     

La2O3含量对Al2O3/Cu基复合材料组织与性能的影响

以La₂O₃粉、Al粉、CuO粉为反应物原料、纯铜为基体,采用原位合成技术和近熔点铸造法制备颗粒增强Cu基复合材料,研究La₂O₃对Al-CuO体系制备的Cu基复合材料组织及性能的影响。结果表明：添加La₂O₃可获得纳米Al₂O₃颗粒,且弥散分布于Cu基体中,制备的材料组织更加细小、均匀,其材料的电导率及摩擦磨损性能明显提高。当添加0.6%wtLa₂O₃,复合材料的电导率达到90.2%IACS,磨损量达到最小,相比未添加La₂O₃,其导电率提高10.1%,磨损量减小36.6%。     

Mechanochemical synthesis of Al2O3-TiB2 nanocomposite powder from Al-TiO2-H3BO3 mixture

Alumina-titanium diboride nanocomposite (Al₂O₃-TiB₂) was produced using mixtures of titanium dioxide, acid boric and pure aluminum as raw materials via mechanochemical process. The phase transformation and structural characterization during mechanochemical process were utilized by X-ray diffractometry (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), and thermogravimetric analyses (TG-DTA) techniques. A thermodynamic appraisal showed that the reaction between TiO₂, B₂O₃ and Al is highly exothermic and should be self-sustaining. XRD analyses exhibited that the Al₂O₃-TiB₂ nanocomposite was formed after 1.5 h milling time. The results indicate that increasing milling time up to 40 h had no significant effect other than refining the crystallite size.     

Microstructure and mechanical properties of Al2O3-Cr2O3 composite coatings produced by atmospheric plasma spraying

Al₂O₃, Al₂O₃-Cr₂O₃ and Cr₂O₃ coatings were deposited by atmospheric plasma spraying. Phase composition of powders and as-sprayed coatings was determined by X-ray diffraction. Electron probe microanalyzer was employed to investigate the polished and fractured surface morphologies of the coatings. Mechanical properties including microhardness, fracture toughness and bending strength were evaluated. The results indicate that the addition of Cr₂O₃ is conducive to the stabilization of α-Al₂O₃. Compared with the pure Al₂O₃ and Cr₂O₃ coatings, Al₂O₃-Cr₂O₃ composite coatings show lower porosities and denser structures. Heterogeneous nucleation of α-Al₂O₃ occurs over the isostructural Cr₂O₃ lamellae and partial solid solution of Al₂O₃ and Cr₂O₃ might be occurring as well. Furthermore, grain refining and solid solution strengthening facilitate the mechanical property enhancement of Al₂O₃-Cr₂O₃ composite coatings.     

Synthesis and characterization of Al2O3-Ce0.5Zr0.5O2 powders prepared by chemical coprecipitation method

Al₂O₃-Ce_0.5Zr_0.5O₂ catalytic powders were synthesized by the coprecipitation (ACZ-C) and mechanical mixing (ACZ-M) methods, respectively. As-synthesized powders were characterized by XRD, Raman spectroscopy, surface area and thermogravimetric analyses. It was found that the mixing extent of Al³⁺ ions affected the phase development, texture and oxygen storage capacity (OSC) of the Ce_0.5Zr_0.5O₂ powder. Single phase of ACZ-C could be maintained without phase separation and inhibit α-Al₂O₃ formation up to 1200 °C. The specific surface area value of ACZ-C (81.5 m²/g) was larger than that of ACZ-M (62.1 m²/g) and Ce_0.5Zr_0.5O₂ (17.1 m²/g) powders, which were calcined at 1000 °C. In comparison with ACZ-C and Al₂O₃, which were calcined at high temperature (900–1200 °C), it was found that the degradation rate of specific surface area of ACZ-C was lower than that of Al₂O₃. ACZ-C sample showed a higher thermal stability to resist phase separation and crystallite growth, which enhanced the oxygen storage capacity property for Ce_0.5Zr_0.5O₂ powders.     

Scratching of Al2O3 under pre-stressing

Pre-stressing scratching tests have been preformed on polished surfaces of Al₂O₃ ceramic under a Rockwell diamond indenter which moved with uniform speed and constant normal load to investigate how the pre-stress contributes to the material removal mechanism. With the measurement of acoustic emission signals as well as indenter tangential forces, surface damages and cross-section of grooves of Al₂O₃ ceramic were evaluated under the action of different values of pre-stress. It was found that the scratched groove width was increased with the increasing of pre-stress when same normal loads were applied. The existence of pre-stress tends to restrain the crack propagation along the direction of pre-stress, and obvious plastic deformation at the bottom of scratched groove has been observed. Moreover, the fluctuation of tangential force was obviously enhanced, and the magnitude of tangential force in the test of pre-stress was higher than that of without pre-stress. The acoustic emission signals showed that fewer damages were produced in the process of scratching with an appropriate pre-stress. However, the continuing increase of pre-stress would aggravate the machining process.