Thermostimulative shape memory effect of linear low‐density polyethylene/polypropylene (LLDPE/PP) blends compatibilized by crosslinked LLDPE/PP blend (LLDPE–PP)

A novel linear low‐density polyethylene (LLDPE)/polypropylene (PP) thermostimulative shape memory blends were prepared by melt blending with moderate crosslinked LLDPE/PP blend (LLDPE–PP) as compatibilizer. In this shape memory polymer (SMP) blends, dispersed PP acted as fixed phase whereas continuous LLDPE phase acted as reversible or switch phase. LLDPE–PP improved the compatibility of LLDPE/PP blends as shown in scanning electron microscopic photos. Dynamic mechanical analysis test showed that the melt strengths of the blends were enhanced with increasing LLDPE–PP content. A shape memory mechanism for this type of SMP system was then concluded. It was found that when the blend ratio of LLDPE/PP/LLDPE–PP was 87/13/6, the blend exhibited the best shape memory effect at stretch ratio of 80%, stretch rate of 25 mm/min, and recovery temperature of 135°C. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Development of nanofibrous morphology in LDPE/LLDPE/PP blends and its effect on mechanical properties of blend films

Nanofibrous morphology has been observed in ternary blends of low density polyethylene (LDPE), linear low density polyethylene (LLDPE), and isotactic polypropylene (PP) when these were melt‐extruded via slit die followed by hot stretching. The morphology was dependent on the concentration of the component polymers in ternary blend LDPE/LLDPE/PP. The films were characterized by wide angle X‐ray diffraction (XRD), scanning electron microscopy (SEM), and testing of mechanical properties. The XRD patterns reveal that the β phase of PP is obtained in the as‐stretched nanofibrillar composites, whose concentration decreases with the increase of LLDPE concentration. The presence of PP nanofibrils shows significant nucleation ability for crystallization of LDPE/LLDPE blend. The SEM observations of etched samples show an isotropic blend of LDPE and LLDPE reinforced with more or less randomly distributed and well‐defined nanofibrils of PP, which were generated in situ. The tensile modulus and strength of LDPE/LLDPE/PP blends were significantly enhanced in the machine direction than in the transverse direction with increasing LLDPE concentration. The ultimate elongation increased with increasing LLDPE concentration, and there was a critical LLDPE concentration above which it increased considerably. There was a dramatic increase in the falling dart impact strength for films obtained by blow extrusion of these blends. These impressive mechanical properties of extruded samples can be explained on the basis of the formation of PP nanofibrils with high aspect ratio (at least 10), which imparted reinforcement to the LDPE/LLDPE blend. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

PP/LLDPE共混体系的研究

研究了聚丙烯(PP)／线性低密度聚乙烯(LLDPE)共混体系的形态结构与宏观性能之间的关系。对共混用的PP和LLDPE品种以及共混的工艺路线进行了选择；采用扫描电子显微镜(SEM)和偏光显微镜(PLY)观察了PP／LLDPE微观形态结构，并测试了力学性能和热性能。结果表明：屈服强度、拉伸模量、维卡软化点降低；当LLDPE用量增大时，随着LLDPE用量增加，材料的冲击强度增加，而拉伸共混体系形成互穿网络结构，具有良好的综合性能。     

Mechanical and thermal properties of calcium carbonate‐filled PP/LLDPE composite

Polymer blends typically are the most economical means to develop new resins for specific applications with the best cost/performance balance. In this paper, the mechanical properties, melting, glass transition, and crystallization behavoir of 80 phr polypropylene (PP) with varying weights of linear low density polyethylene (LLDPE) at 10, 20/ 20 wt % CaCO₃, 30, 40, and 50 phr were studied. A variety of physical properties such as tensile strength, impact strength, and flexural strength of these blends were evaluated. The compatibility of these composite was examined by differential scanning calorimetry (DSC) to estimate T_m and T_c, and by dynamic mechanical analysis (DMA) to estimate T_g. The fractographic analysis of these blends was examined by scanning electron microscopy (SEM). It has been confirmed that increasing the LLDPE content trends to decreases the tensile strength and flexural strength. However, increasing the LLDPE content led to increases in the impact strength of PP/LLDPE blends. It was also found that up to 40 phr the corresponding melting point (T_m) was not effected with increasing LLDPE content. Each compound has more than one T_g, which was informed that there is a brittle‐ductile transition in fracture nature of these blends, the amount of material plastically deformed on the failure surface seems to increase with the increasing the LLDPE content. And PP/LLDPE blends at temperature (23°C) showed a ductile fracture mode characterized by the co‐existence of a shear yielding process; whereas at lower temperature (−20°C) the fractured surfaces of specimens appear completely brittle. The specimens broke into two pieces with no evidence of stress whitening, permanent macroscopic deformation or yielding. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

PP/LLDPE交联共混物的力学性能研究

采用两步交联加工法制备出具有优良力学性能的PP／LLDPE共混物。实验表明：当m(PP)／m(LLDPE)／m(SBS)／m(交联剂)为80／20／10／3时，交联共混物的冲击强度、拉伸强度和断裂伸长率分别达到466．3J／m、27．1MPa和715．1％，比未交联的共混物分别提高262％、8．28％和115％；交联作用的存在使共混物的脆韧转变点明显提前；随交联剂用量的增加，共混物的力学性能不断提高，但增大趋势逐渐变小。     

Mechanical properties and morphology of polyethylene–polypropylene blends with controlled thermal history

The effect of time–temperature treatment on the mechanical properties and morphology of polyethylene–polypropylene (PE–PP) blends was studied to establish a relationship among the thermal treatment, morphology, and mechanical properties. The experimental techniques used were polarized optical microscopy with hot‐stage, scanning electron microscopy (SEM), differential scanning calorimetry (DSC), and tensile testing. A PP homopolymer was used to blend with various PEs, including high‐density polyethylene (HDPE), low‐density polyethylene (LDPE), linear low‐density polyethylene (LLDPE), and very low density polyethylene (VLDPE). All the blends were made at a ratio of PE:PP = 80:20. Thermal treatment was carried out at temperatures between the crystallization temperatures of PP and PEs to allow PP to crystallize first from the blends. A very diffuse PP spherulite morphology in the PE matrix was formed in partially miscible blends of LLDPE–PP even though PP was present at only 20% by mass. Droplet‐matrix structures were developed in other blends with PP as dispersed domains in a continuous PE matrix. The SEM images displayed a fibrillar structure of PP spherulite in the LLDPE–PP blends and large droplets of PP in the HDPE–PP blend. The DSC results showed that the crystallinity of PP was increased in thermally treated samples. This special time–temperature treatment improved tensile properties for all PE–PP blends by improving the adhesion between PP and PE and increasing the overall crystallinity. In particular, in the LLDPE–PP blends, tensile properties were improved enormously because of a greater increase in the interfacial adhesion induced by the diffuse spherulite and fibrillar structure. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 1151–1164, 2000     

Processing‐improved properties and morphology of PP/COC blends

The aim of this study was to improve mechanical properties of polypropylene/cycloolefin copolymer (PP/COC) blends by processing‐induced formation of long COC fibers. According to the available literature, the fibrous morphology in PP/COC blends was observed just once by coincidence. For this reason, we focused our attention on finding processing conditions yielding PP/COC fibrous morphology in a well‐defined, reproducible way. A number of PP/COC blends were prepared by both compression molding and injection molding (IM). Neat polymers were characterized by rheological measurements, whereas phase morphology of the resulting PP/COC blends was characterized by means of scanning electron microscopy (SEM). The longest COC fibers were achieved in the injection molded PP/COC blends with compositions 75/25 and 70/30 wt %. Elastic modulus and yield strength of all blends were measured as functions of the blend composition using an Instron tensile tester; statistically significant improvement of the yield strength due to fibrous morphology was proved. Moreover, two different models were applied in the analysis of mechanical properties: (i) the equivalent box model for isotropic blends and (ii) the Halpin‐Tsai model for long fiber composites. In all PP/COC blends prepared by IM, the COC fibers were oriented in the processing direction, as documented by SEM micrographs, and acted as a reinforcing component, as evidenced by stress–strain measurements. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Processability and mechanical properties for binary blends of PP and LLDPE produced by metallocene catalyst

Processability at extrusion coating and mechanical properties of the films obtained are investigated by means of linear and nonlinear rheological measurements and tensile tests for blends of polypropylene (PP) and linear low‐density polyethylene (LLDPE). Both materials are produced by metallocene catalyst. The processability of PP is found to be improved by the addition of LLDPE; the blend shows low level of motor torque and head pressure in an extruder and small level of neck‐in as compared with pure PP. Further, the anisotropy of ultimate tensile strength, which is prominent for PP, is reduced by blending with LLDPE. As a result, the blend having 20 wt % of LLDPE shows appropriate properties in the molten state for extrusion coating and in the solid state as a film. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

An investigation on recycled PET/PP and recycled PET/PP‐EP compatibilized blends: Rheological,morphological, and mechanical properties

The effectiveness of P(E‐co‐MA‐co‐GMA) as a compatibilizer for recycled PET/PP and recycled PET/PP‐EP (polypropylene (ethylene‐propylene) heterophase copolymer) blends was investigated by means of morphological (scanning electron microscopy), rheological (small amplitude oscillatory shear), mechanical (tensile, flexural and impact tests), and thermal (differential scanning calorimetry) properties. Compatibilizer concentration ranged from 1 to 5 wt % with respect to the whole blend. All blends were obtained in a 90/10 composition using a twin screw extruder. Compatibilization effects for PETr/PP‐EP were more pronounced due to ethylene segments present in both PP‐EP and P(E‐co‐EA‐co‐GMA). PETr/PP‐EP has shown greater dispersed phase size reduction, a more solid‐like complex viscosity behavior and larger storage modulus at low frequencies in relation to PETr/PP blend. For both investigated blends, mechanical properties indicated an improvement in both elongation at break and impact strength with increasing compatibilizer content. PETr/PP‐EP blends showed improved performance for the same level of compatibilizer content. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41892.     

Effect of flexibility of ethylene vinyl acetate and crystallization of polypropylene on the mechanical properties of i‐PP/EVA blends

Polymer blend technology has been widely used for the past several years for the modification or enhancement of mechanical properties of polymers to obtain an overall balance of properties over those of the constituents. Despite its interesting mechanical and thermal properties, the impact strength of polypropylene leaves wide scope for improvement. A series of blends of ethylene vinyl acetate (EVA) copolymer with an impact grade of isotactic polypropylene (i‐PP) were prepared by single screw extrusion at 0–0.32 volume fraction of the dispersed phase. The mechanical properties such as tensile behavior, elongation‐at‐break, and impact strength of these blends systems as well as crystallinity were evaluated. Crystallinity data have been used in greater depth to support the mechanical properties. Differential scanning calorimetry studies conducted to study the modification in crystallinity of the crystalline component, i‐PP, of the blend revealed that the rubber component of the blend enhanced the crystallinity of i‐PP phase by providing sites for nucleation. Tensile modulus and strength decreased while the impact strength and breaking elongation enhanced with blending elastomer concentration. The improved properties of these PP/EVA blends are encouraging for carrying out further work on this system (composites) and suggest potential high impact strength applications for PP. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effects of compatibilization of oxidized polypropylene on PP blends of PP/PA6 and PP/talc

The influence of compatibilization on the dynamic mechanical properties of polypropylene (PP) binary blends with polyamide‐6 (PA6), Talc, and oxidized PP (OPP) was investigated. The oxidation of PP homopolymer was performed in a internal mixer by using air as a oxidizing agent (under atmospheric pressure) and dodecanol‐1 as an accelerator at 180°C for 6½ h [Abdouss, M.; Sharifi‐Sanjani, N.; Bataille, P. J Appl Polym Sci 1999, 36, 10]. In the blends, OPP was used as a blend component and compared with PP over the whole concentration range. Pressed film blends of PP/OPP, PP/OPP/Talc, and PP/OPP/PA6 were examined by dynamic mechanical analyzer, thermal gravimetry analysis, and scanning electron microscopy. Mechanical properties such as tensile strength, modulus of elasticity, elongation, melt flow index, and hardness of the blends were measured. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2871–2883, 2004     

Morphology and properties of PP/EPDM binary blends and PP/EPDM/nano‐CaCO3 ternary blends

In this article, the morphology, crystallization, and rheological behaviors of polypropylene (PP)/ethylene‐propylene‐diene terpolymer (EPDM) binary blend and PP/EPDM/calcium carbonate nanoparticles (nano‐CaCO₃) ternary blend were investigated. Two processing methods, i.e., direct extrusion and two‐step extrusion, were employed to prepare the PP/EPDM/CaCO₃ blend. The influence of EPDM and nano‐CaCO₃ respectively on phase morphology and properties of PP/EPDM blend and PP/EPDM/CaCO₃ blend were characterized by scanning electron microscopy (SEM), differential scanning calorimetry (DSC) and dynamic rheometer. The crystallinity and crystallization temperature of PP/EPDM blend were improved in comparison to pure PP due to addition of EPDM, but kept invariable with the increased EPDM loading. As the EPDM content was increased, the mobility of PP molecular chains was weakened. Compared with direct extruded blend, less and finer nano‐CaCO₃ was dispersed in matrix of two‐step extruded blend. Accordingly, the increased nano‐CaCO₃ in matrix gave rise to a weaker increment in crystallinity and crystallization temperature of two‐step extruded blend, and a later platform of tanδ curve. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Thermoplastic Elastomers Derived from Scrap Rubber Powder/LLDPE Blend with LLDPE‐graft‐(Epoxidized Natural Rubber) Dual Compatibilizer

Summary: Attempts were made to prepare thermoplastic elastomers (TPE) from scrap rubber powder (SRP) and linear low‐density polyethylene (LLDPE) as thermoplastic polymer matrix. The solid‐phase grafted copolymer of LLDPE (LLDPE‐g‐VM) and epoxidized natural rubber (ENR) were used as dual compatibilizers to improve the interfacial adhesion between SRP and LLDPE. The compatibilized SRP/LLDPE blends had obviously improved the interfacial properties between SRP particles and LLDPE. Using this method, thermoplastic elastomer was prepared successfully. The mechanical properties especially elongation at break was improved significantly. SEM and TEM studies showed that the ENR/LLDPE‐g‐VM dual compatibilizer improved the distribution state of SRP particles in LLDPE and the adhesion between SRP and LLDPE. DSC results showed a distinct glass transition at 74 °C of the interfacial region. The improvement in mechanical properties was attributed to the enhanced interfacial properties of the blend.

Surface of SRP particles of the composites compatibilized by the dual compatibilizer.     

Covulcanization of LLDPE/EMA blends using dicumyl peroxide

The effect of dicumyl peroxide (DCP) content on the gel fraction, mechanical, dynamic mechanical, and thermal properties of linear low‐density polyethylene (LLDPE)/ethylene‐co‐methyl acrylate (EMA) blends were studied. Gel content of the blends increases with increasing DCP content, and EMA is more prone to crosslinking than LLDPE. Wide‐angle X‐ray diffraction (WAXD) and differential scanning calorimetry (DSC) were used to study the effect of DCP crosslinking on percent crystallinity and crystalline structure of the blends and individual components. At lower level of DCP loading, crosslinking process does not have significant effect on the crystalline structure of the LLDPE, which was confirmed from the percent crystallinity and lattice distance value. However, at higher DCP content, percent crystallinity decreases significantly. At lower EMA concentration (<50%), percent crystallinity and lattice distance remain unchanged up to 2 wt % of DCP. For EMA contents of more than 50 wt %, increasing DCP content reduces the crystallinity of the blends and increases the lattice distance. The highest level of mechanical and dynamic mechanical properties was observed for 60/40 LLDPE/EMA blends at 2 wt % DCP. Addition of LLDPE‐g‐MA (3 wt %) as a compatibilizer enhances the properties of the vulcanizates. Blends crosslinked with DCP up to 0.3 wt % can easily be reprocessed. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Mechanical properties and morphology of PP/ABS blends compatibilized with PP‐g‐2‐HEMA

Polypropylene (PP) and acrylonitrile–butadiene–styrene blends of different composition were prepared using a single‐screw extruder. The binary blend of PP/ABS was observed to be incompatible and shows poor mechanical properties. PP‐g‐2‐hydroxyethyl methacrylate (2‐HEMA) was used as a compatibilizer for the PP/ABS blends. The ternary compatibilized blends of PP/ABS/PP‐g‐2‐HEMA showed improvement in the mechanical properties. Electron micrographs of these blends showed a homogeneous and finer distribution of the dispersed phase. The mechanical performance increased particularly in the PP‐rich blend. The 2.5‐phr (part per hundred of resin) compatibilizer was observed to bring improvement to the properties. The suitability of various existing theoretical models for the predication of the tensile moduli of these blends was examined. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 72–78, 2003     

Effect of clay type and polymer matrix on microstructure and tensile properties of PLA/LLDPE/clay nanocomposites

Polylactide (PLA)/linear low‐density polyethylene (LLDPE), (PLA/LLDPE), blends and nanocomposites were prepared by melt mixing process with a view to fine tune the properties. Two different commercial‐grade nanoclays, Cloisite® 30B (30B) and Cloisite® 15A (15A) were used. A terpolymer of ethylene, butylacrylate (BA) and glycidylmethacrylate (GMA) was used as a reactive compatibilizer. The influence of type of clay on the morphology and mechanical properties of two PLA‐rich and LLDPE‐rich blend systems was studied. Morphological analysis using X‐ray diffraction, transmission electron microscopy, and scanning electron microscopy revealed that the organoclay layers were dispersed largely at the interface of PLA/LLDPE. Decreasing the PLA content changed the morphology from droplet‐in matrix to coarse co‐continuous. In comparison with 30B, due to less affinity of 15A towards compatibilizer and PLA phase, the reduction of the size of dispersed phase was less than that of the equivalent 30B composites. The mechanical results demonstrated that the composites containing both types of organoclay exhibited higher modulus but lower elongation and tensile strength as compared to the neat blends. The injection molded nanocomposites were shown to have the sequential fracture behavior during tensile test. The tensile testing results on the neat blends and nanocomposites showed significant increase in elongation at break and decrease in the modulus as compared with the neat PLA. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 749‐758, 2013     

Dynamically cured polypropylene/Novolac blends compatibilized with maleic anhydride‐g‐polypropylene

In this article, the dynamic vulcanization process was applied to polypropylene (PP)/Novolac blends compatibilized with maleic anhydride‐grafted PP (MAH‐g‐PP). The influences of dynamic cure, content of MAH‐g‐PP, Novolac, and curing agent on mechanical properties of the PP/Novolac blends were investigated. The results showed that the dynamically cured PP/MAH‐g‐PP/Novolac blend had the best mechanical properties among all PP/Novolac blends. The dynamic cure of Novolac improved the modulus and stiffness of the PP/Novolac blends. The addition of MAH‐g‐PP into dynamically cured PP/Novolac blend further enhanced the mechanical properties. With increasing Novolac content, tensile strength, flexural modulus, and flexural strength increased significantly, while the elongation at break dramatically deceased. Those blends with hexamethylenetetramine (HMTA) as a curing agent had good mechanical properties at HMTA content of 10 wt %. Scanning electron microscopy (SEM) analysis showed that dynamically cured PP/MAH‐g‐PP/Novolac blends had finer domains than the PP/MAH‐g‐PP/Novolac blends. Thermogravimetric analysis (TGA) results indicated that the incorporation of Novolac into PP could improve the thermal stability of PP. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Studies on the engineering properties of LCP‐Vectra B 950/PP blends with the variations of EAA content

Polypropylene (PP) was melt blended with Vectra B‐950 [a thermotropic liquid crystalline polymer (LCP)], in a single screw extruder in presence of different doses of ethylene acrylic acid (EAA) copolymer, as modifier. The effect of incorporation in different proportions of EAA at a fixed dose of 5% LCP, on mechanical, thermal, morphological, and rheological properties of such blends was studied and the same were compared with that of pure PP and amongst themselves. Mechanical analysis (tensile properties) of the prepared blends exhibited improvements in ultimate tensile strength (UTS), modulus, toughness, hardness, and impact strength of PP matrix with the incorporation of EAA. The improvement in mechanical properties is associated with the formation of LCP fibrils as evidenced by scanning electron microscopy (SEM). A strong interaction through H‐bonding between the segments of Vectra B‐950 and EAA was established by FTIR study. Differential scanning calorimetry (DSC) studies indicated substantial increase in melting point of the blends, and thermogravimetric analysis (TGA) showed that the thermal stability of PP was improved with the addition of LCP and EAA. Rheological properties showed that LCP and EAA drop down the melt viscosity of PP and thus facilitate processibility of blends. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Mechanical properties and morphology of crosslinked PP/PE blends and PP/PE/propylene–ethylene copolymer blends

Blending is an effective method for improving polymer properties. However, the problem of phase separation often occurs due to incompatibility of homopolymers, which deteriorates the physical properties of polyblends. In this study, isotactic polypropylene was blended with low-density polyethylene. Crosslinking agent and copolymers of propylene and ethylene (either random copolymer or block copolymer) were added to improve the interfacial adhesion of PP/LDPE blends. The tensile strength, heat deflection temperature, and impact strength of these modified PP/PE blends were investigated. The microstructures of polyblends have been studied to interpret the mechanical behavior through dynamic viscoelasticity, wide-angle X-ray diffraction, differential scanning calorimetry, picnometry, and scanning electron microscopy. The properties of crosslinked PP/PE blends were determined by the content of crosslinking agent and processing method. For the material blended by roll, a 2% concentration of peroxide corresponded to a maximum tensile strength and minimum impact strength. However, the mechanical strength of those products blended by extrusion monotonously decreased with increasing peroxide content because of serious degradation. The interfacial adhesion of PP/PE blends could be enhanced by adding random or block copolymer of propylene and ethylene, and the impact strength as well as ductility were greatly improved. Experimental data showed that the impact strength of PP/LDPE/random copolymer ternary blend could reach as high as 33.3 kg · cm/cm; however, its rigidity and tensile strength were inferior to those of PP/LDPE/block copolymer blend.     

A study of LLDPE functionalized through ultraviolet irradiation and interfacial interaction of PA66/functionalized LLDPE blends

Some oxygen‐containing groups, such as C? O? C, C? OH, C?O, C(?O)O, and C(?O)OH, were introduced onto linear low‐density polyethylene (LLDPE) chains during ultraviolet irradiation under air, without adding any monomers and auxiliaries and without environmental pollution. After ultraviolet irradiation, the molecular weight of LLDPE decreased and its distribution became wider. The melting temperature and crystallinity of irradiated LLDPE decreased with irradiation time. The copolymer LLDPE‐g‐PA66 was formed by reaction between oxygen‐containing groups of irradiated LLDPE and amine or carboxyl end groups and amide linkage of polyamide 66 (PA66) during preparation of PA66/irradiated LLDPE blends. Compared with PA66/LLDPE blend, the mechanical properties of PA66/irradiated LLDPE blends were improved greatly because of the improved interface interaction and dispersion. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006