Formation of a cohesive floodplain in a dynamic experimental meandering river

Field studies suggest that a cohesive floodplain is a necessary condition for meandering in contrast to braided rivers. However, it is only partly understood how the balance between floodplain construction by overbank deposition and removal by bank erosion and chutes leads to meandering. This is needed because only then does a dynamic equilibrium exist and channels maintain meandering with low width–depth ratios. Our objective is to understand how different styles of floodplain formation such as overbank deposition and lateral accretion cause narrower channels and prevent chute cutoffs that lead to meandering. In this study we present two experiments with a self‐forming channel in identical conditions, but to one we added cohesive silt at the upstream boundary. The effect of cohesive silt on bank stability was tested in auxiliary bank erosion experiments and showed that an increase in silt reduced erosion rates by a factor of 2. The experiment without silt developed to a braided river by continuous and extensive shifting of multiple channels. In contrast, in the meandering river silt deposits increased bank stability of the cohesive floodplain and resulted in a reduction of chute cutoffs and increased sinuosity by continuous lateral migration of a single channel. Overbank flow led to deposition of the silt and two styles of cohesive floodplain were observed: first, overbank vertical‐accretion of silt, e.g. levee, overbank sedimentation or splays; and second, lateral point bar accretion with silt on the scrolls and in the swales. The first style led to a reduction in bank erosion, while the second style reduced excavation of chutes. We conclude that sedimentation of fine cohesive material on the floodplain by discharge exceeding bankfull is a necessary condition for meandering. Copyright © 2013 John Wiley & Sons, Ltd.     

The impact of afforestation on stream bank erosion and channel form

Modification of the land use of a small catchment through coniferous afforestation is shown to have influenced stream bank erosion and channel form. Field mapping and erosion pin measurements over a 19-month period provides evidence of more active bank erosion along forested channel reaches than along non-forested. Extrapolation of downstream increases in bankfull width, bankfull depth, and channel capacity with increasing basin area for the non-forested catchment has demonstrated that afforestation of the lower part of the catchment has had a marked effect on channel form. Channel widths within the forest are up to three times greater than that predicted from the regression. These changes in bankfull width have led to stream bed aggradation and the development of wide shallow channels within the forest, and channel capacities within the forest are over two times that predicted from the basin area. The relationship between channel sinuosity and valley gradient for non-forested reaches of the river also indicated decreased sinuosity resulting from afforestation. These changes in channel form result from active bank erosion within the forest with coarse material being deposited within the channel as point-bars and mid-channel bars. Active bank erosion is largely attributed to the suppression by the forest of a thick grass turf and its associated dense network of fine roots, and secondly to the river attempting to bypass log jams and debris dams in the stream channel.     

Vegetation controls on channel stability in the Bell River,Eastern Cape,South Africa

Channel instability has occurred in the Bell River in the form of meander cutoffs, a number of which have occurred since 1952. Increased sediment loading from widespread gully erosion in the catchment has been proposed as the trigger for this instability. Willow species of the Salix family, in particular S. caprea, have been planted along the banks in an effort to prevent further channel shifting. This study reports the results of an investigation into the effect of vegetation on channel form and stability over a 17 km stretch of channel. Results indicate that riparian vegetation has significant effects on channel form which have implications for channel stability. Riparian vegetation increases bank stability and reduces channel cross-sectional area, thereby inducing stability at flows less than bankfull. Evidence indicates that narrow stable stretches are associated with relatively high levels of riparian vegetation. Wider, unstable channels are associated with relatively less riparian vegetation. The effectiveness of riparian vegetation relative to bank sediments was investigated. A dense growth of willows was found to have an equivalent effect to banks with a silt-clay ratio of about 70 per cent. The channel narrowing induced by vegetation may contribute to channel shifting at high flows. The reduced channel capacity is thought to result in more frequent overbank flooding which may ultimately lead to channel avulsion. Thus where increased sediment loading is pushing the channel towards instability, vegetation may be effective in imparting local stability, but it is unable to prevent long-term channel shifts, and may rather help to push the system towards more frequent avulsions. Copyright © 1999 John Wiley & Sons, Ltd.     

RETROGRESSIVE EROSION AND LONGITUDINAL PROFILE EVOLUTION IN NONCOHESIVE MATERIAL

1 INTRODUCTION A headcut, which is an abrupt break in the slope of a channel bed, is often called a “knickpoint” or “scarp” in the study of rivers and waterways. A headcut tends to retreat upstream as water flows over it. As a headcut passes a cross s…     

Length scales and statistical characteristics of outer bank roughness for large elongate meander bends: The influence of bank material properties,floodplain vegetation and flow inundation

This article explores the length scales and statistical characteristics of form roughness along the outer banks of two elongate bends on a large meandering river through investigation of topographic variability of the bank face. The analysis also examines how roughness varies over the vertical height of the banks and when the banks are exposed subaerially and inundated during flood stage. Detailed data on the topography of the outer banks were obtained subaerially using terrestrial LiDAR during low flow conditions and subaqueously using multibeam echo sounding (MBES) during near‐bankfull conditions. The contributions of various length scales of topographic irregularity to roughness for subaerial conditions were evaluated for different elevation contours on the bank faces using Hilbert–Huang Transform (HHT) spectral analysis. Statistical characteristics for discrete areas on the bank faces were determined by calculating the root‐mean‐square of normal distances from a triangulated irregular network (TIN) surface. Results of the HHT analysis show that the characteristics of roughness along bank faces composed primarily of non‐cohesive sediment, and eroding into cropland, vary with bank elevation and exhibit a dominant range of roughness length scales (~15–50 m). However, bank faces composed predominantly of cohesive material and carved into a forested floodplain have relatively uniform topographic roughness characteristics over the vertical extent of the bank face and do not exhibit a dominant roughness length scale or range of length scales. Additionally, comparison between local surface roughness for subaerial versus subaqueous conditions shows that roughness decreases considerably when the banks are submerged, most likely because of the removal of vegetation and eradication of small‐scale erosional features in non‐cohesive bank materials by flow along the bank face. Thus, roughness appears to be linked to the hydraulic conditions affecting the bank, at least relative to conditions that develop when banks are exposed subaerially. Copyright © 2017 John Wiley & Sons, Ltd.     

Three-dimensional modeling of bank erosion and morphological changes in the Shishou bend of the middle Yangtze River

This paper presents a three-dimensional (3-D) numerical model to simulate morphological changes in alluvial channels due to bank erosion. A method for the simulation of bank erosion is established. This is incorporated into a 3-D mathematical model for turbulent flow and non-uniform, non-equilibrium sediment transport. This model is applied to simulate morphological changes in the Shishou bend of the middle Yangtze River in China, where serious bank erosions occurred during the last two decades. The double-layer sediment structure of the riverbank on the middle Yangtze River is taken into account in the bank erosion module. Both cohesive and non-cohesive bank material in the different layers are considered. The bank erosion module also includes other factors affecting the rate of bank erosion, such as the longitudinal length of failed bank, the thickness of each layer in the double-layer structure, and the erosion-resisting effect of cohesive material from the top layer of failed bank. A locally-adaptive grid system is proposed to efficiently simulate the lateral migration of alluvial channel due to bank erosion. The predictive capability of the 3-D model is examined by laboratory data. Simulated processes of bank erosion agree with field observations in the Shishou bend during the period of October 1996–October 1998, and the bank erosion module plays a significant role in simulating morphological changes of the study reach. In addition, the equivalent channel-forming discharge, which is defined as a constant discharge that can create the same amount of bank erosion in an alluvial channel as that created by natural runoff processes during the same period of time, is proposed to improve calculation efficiency for feasibility studies.     

Modelling the effect of vegetation on channel pattern in bedload rivers

We modify a simple numerical stream‐pattern model to examine the effect of sediment stabilization by roots on the channel pattern of bedload rivers. In the model, vegetation enhances bank resistance to erosion, causing the development of a single channel instead of a rapidly changing, multiple channel (braided) pattern. Net aggradation resulting from a high sediment supply, however, causes frequent avulsions that destroy vegetation locally, leading to the development of a multiple‐channel pattern. A stability diagram representing multiple model runs predicts whether a river will exhibit single or multiple channels, based on plant‐enhanced bank strength, and on the time scale of plant development relative to a time scale for change in unvegetated channels. A second stability diagram predicts the way in which the amplitude and period of a fluctuating imposed sediment load influence whether a single or multiple‐channel pattern develops. Copyright © 2003 John Wiley & Sons, Ltd.     

三峡工程运用后城陵矶-武汉河段河床调整及崩岸特点

为研究近期城汉河段河床调整及崩岸特点,利用实测水沙及地形等资料,采用河段平均的方法,计算了城汉河段断面形态的调整过程,主要包括平滩河槽形态调整及其与前期水沙条件之间的关系.计算结果表明：城汉河段平滩河宽由2003年的1710 m增加至2016年的1732 m,增幅为1.28%,平滩水深由2003年的16.47 m增加至2016年的17.95 m,增幅为9.0%;白螺矶、界牌、簰洲及武汉等河段河床调整以纵向冲深为主,但陆溪口河段河床调整横向展宽与纵向冲深同步发展;2006-2016年城汉河段多年平均崩退速率为5.5 m/a,崩岸总长19.6 km,占岸线总长的8.3%,右岸占55.3%.簰洲河段岸线崩长占城汉河段岸线崩退总长的75.9%.此外还分析了河床边界与水沙条件等因素对重点河段（簰洲河段）崩岸过程的影响,来水来沙条件占主导地位,局部区域崩岸的发生依赖于河床边界条件;建立了典型断面平滩河宽与前期水沙条件之间的经验关系,较好地反映了水沙条件变化对崩岸过程的影响.     

Sedimentation of overbank floods in the confined complex channel–floodplain system of the Lower Yellow River,China

The channel boundary conditions along the Lower Yellow River (LYR) have been altered significantly since the 1950s with the continual reinforcement and construction of both main and secondary dykes and river training works. To evaluate how the confined complex channel–floodplain system of the LYR responds to floods, this study presents a detailed investigation of the relationship between the tempo‐spatial distribution of sedimentation/erosion and overbank floods occurred in the LYR. For large overbank floods, we found that when the sediment transport coefficient (ratio of sediment concentration of flow to flow discharge) is less than 0.034, the bankfull channel is subject to significant erosion, whereas the main and secondary floodplains both accumulate sediment. The amount of sediment deposited on the main and secondary floodplains is closely related to the ratio of peak discharge to bankfull discharge, volume of water flowing over the floodplains, and sediment concentration of overbank flow, whereas the degree of erosion in the bankfull channel is related to the amount of sediment deposited on the main and secondary floodplains, water volume, and sediment load in flood season. The significant increase in erosion in the bankfull channel is due to the construction of the main and secondary dykes and river training works, which are largely in a wide and narrow alternated pattern along the LYR such that the water flowing over wider floodplains returns to the channel downstream after it drops sediment. For small overbank floods, the bankfull channel is subject to erosion when the sediment transport coefficient is less than 0.028, whereas the amount of sediment deposited on the secondary floodplain is associated closely with the sediment concentration of flow. Over the entire length of the LYR, the situation of erosion in the bankfull channel and sediment deposition on the main and secondary floodplains occurred mainly in the upper reach of the LYR, in which a channel wandering in planform has been well developed.     

Computer program for stability analysis of steep,cohesive riverbanks

The ability to predict the stability of eroding riverbanks is a prerequisite for modelling alluvial channel width adjustment and a requirement for predicting bank erosion rates and sediment yield associated with bank erosion. Mass‐wasting of bank materials under gravity occurs through a variety of specific mechanisms, with a separate analysis required for each type of failure. This paper presents a computer program for the analysis of the stability of steep, cohesive riverbanks with respect to planar‐type failures. Planar‐type failures are common along stream channels destabilized by severe bed degradation. Existing stability analyses for planar‐type failures have a number of limitations that affect their physical basis and predictive ability. The computer program presented here is based on an analysis developed by Darby and Thorne. The software takes account of the geotechnical characteristics of the bank materials, the shape of the bank profile, and the relative elevations of the groundwater and surface water to estimate stability with respect to mass failure along a planar‐type failure surface. Results can be displayed either in terms of a factor of safety (ratio of resisting to driving forces), or probability of failure. The computer analysis is able to determine the relative amounts of bed degradation and bank‐toe erosion required to destabilize an initially stable bank. Data for the analysis are supplied in the form of either HEC‐2 hydrographic survey data files or user‐supplied bank profile data, in conjunction with user‐supplied geotechnical parameter values. Some examples, using data from the Upper Missouri River in Montana, are used to demonstrate potential applications of the software. Copyright © 2000 John Wiley & Sons, Ltd.     

Effects of wet meadow riparian vegetation on streambank erosion. 2. Measurements of vegetated bank strength and consequences for failure mechanics

We measured the effect of wet meadow vegetation on the bank strength and failure mechanics of a meandering montane meadow stream, the South Fork of the Kern River at Monache Meadow, in California's Sierra Nevada. Streambanks colonized by ‘wet’ graminoid meadow vegetation were on average five times stronger than those colonized by ‘dry’ xeric meadow and scrub vegetation. Our measurements show that strength is correlated with vegetation density indicators, including stem counts, standing biomass per unit area, and the ratio of root mass to soil mass. Rushes appear better than sedges at stabilizing coarse bar surfaces, while sedges are far more effective at stabilizing actively eroding cut banks. Wet meadow floodplain vegetation creates a composite cut bank configuration (a cohesive layer overlying cohesionless materials) that erodes via cantilever failure. Field measurements and a geotechnical model of cantilever stability show that by increasing bank strength, wet meadow vegetation increases the thickness, width, and cohesiveness of a bank cantilever, which, in turn, increases the amount of time required to undermine, detach, and remove bank failure blocks. At Monache Meadow, it takes approximately four years to produce and remove a 1 m wide wet meadow bank block. Wet meadow vegetation limits bank migration rates by increasing bank strength, altering bank failure modes, and reducing bank failure frequency. Copyright © 2002 John Wiley & Sons, Ltd.     

Channel erosion along the Carmel river,Monterey county,California

Historic maps, photographs, and channel cross-sections show that the channel of the Carmel River underwent massive bank erosion, channel migration, and aggradation in a major flood in 1911, then narrowed and incised by 1939. The channel was stable until 1978 and 1980, when bank erosion affected some reaches but not others. The narrowing and incision were in response to a lack of major floods after 1914 and construction in 1921 of a dam that cut off sediment supply from the most actively eroding half of the basin. Localized erosion in 1978 and 1980 occurred during low magnitude events along reaches whose bank strength had been reduced by devegetation. These events illustrate that the stability of a fluvial system can be disrupted either by application of a large erosive force in a high magnitude event (the 1911 flood) or in a low magnitude event, by reducing the resistance to erosion (bank devegetation). The Carmel River is a potentially unstable system. Its discharge and slope characteristics place it near the threshold between meandering and braided. On the Lower Carmel, the presence of bank vegetation can make the difference between a narrow, stable meandering channel and a wide shifting channel with braided reaches.     

Morphodynamic effects of vegetation life stage on experimental meandering channels

Previous studies have demonstrated that riparian vegetation leads to channel transformation from a multi-bar to a single-thread channel planform. However, it still remains unclear how the presence of pioneer and mature vegetation affects the morphodynamics of single-thread meandering rivers. In this study, we therefore investigated the effects of vegetation strength on the morphodynamic evolution of an experimental meandering channel. Three physical laboratory experiments were conducted using alfalfa sprouts in different life stages – no vegetation, immature vegetation, and mature vegetation – to simulate different floodplain vegetation strengths. Our results demonstrate that vegetation plays a key role in mediating bank erosion and point-bar accretion, and that this is reflected in both the evolution of the channel bed as well as the sediment flux. The presence of mature vegetation maintained a deep, single-thread channel by reducing bank erosion, thereby limiting both channel widening and sediment storage capacity. Conversely, an unvegetated floodplain led to channel widening and high sediment storage capacity. Channel evolution in the unvegetated scenario showed that the active sediment supply from outer bank erosion led to slightly delayed point-bar accretion on the inner banks due to helical flow, deflecting the surface flow toward the outer banks and causing further erosion. In contrast, in the immature vegetation scenario, the outer banks were also initially eroded, but point-bar accretion did not clearly progress. This led to a greater width-to-depth ratio, resulting in a transition from a single- to a multi-thread channel with minor flow paths on the floodplain. The experimental results suggest that the eco-morphodynamic effects of young (low-strength) and mature (high-strength) vegetation are different. Notably, low-strength, early-stage vegetation increases channel complexity by accelerating both channel widening and branching, and therefore might promote the coexistence of multi-bars and pioneer vegetation.     

Using a historical aerial photograph analysis to inform trout habitat restoration efforts

Restoration of the upper Strawberry River included bank stabilization techniques because it was assumed that excessive bank erosion was degrading spawning habitat for Bonneville cutthroat trout (BCT). Using a long‐term aerial photograph record, the historical range of variability in bank erosion rates and channel geometry was determined, and this information was used to assess present‐day conditions and the rationale for restoration. Relative to historical variability, the channel planform was relatively stable and bank erosion rates were the lowest recorded in the post‐disturbance era. Although a historical loss of riparian vegetation coincided with a shift to a wider and more sinuous channel, lateral migration rates declined and the channel narrowed as riparian cover increased in the decades before restoration, indicating a process of natural recovery. Furthermore, it was found that the percentage of fine sediment in the streambed before restoration was insufficient to affect BCT spawning success. Together these results suggest that bank erosion and fine sediment did not affect the quality of spawning habitat or the abundance of BCT on the upper Strawberry River. The results highlight how a historical analysis can be used to identify the sources of habitat degradation and inform the selection of restoration goals and strategies. Copyright © 2011 John Wiley & Sons, Ltd.     

Modelling of meander migration in an incised channel

An updated linear computer model for meandering rivers with incision has been developed. The model simulates the bed topography, flow field, and bank erosion rate in an incised meandering channel. In a scenario where the upstream sediment load decreases （e.g., after dam closure or soil conservation）, alluvial river experiences cross section deepening and slope flattening. The channel migration rate might be affected in two ways： decreased channel slope and steeped bank height. The proposed numerical model combines the traditional one-dimensional （1D） sediment transport model in simulating the channel erosion and the linear model for channel meandering. A non-equilibrium sediment transport model is used to update the channel bed elevation and gradations. A linear meandering model was used to calculate the channel alignment and bank erosion/accretion, which in turn was used by the 1D sediment transport model. In the 1D sediment transport model, the channel bed elevation and gradations are represented in each channel cross section. In the meandering model, the bed elevation and gradations are stored in two dimensional （2D） cells to represent the channel and terrain properties （elevation and gradation）. A new method is proposed to exchange information regarding bed elevations and bed material fractions between 1D river geometry and 2D channel and terrain. The ability of the model is demonstrated using the simulation of the laboratory channel migration of Friedkin in which channel incision occurs at the upstream end.     

Geomorphic response of the Jingjiang Reach to the Three Gorges Project operation

Upstream damming often causes significant downstream geomorphic adjustments. Remarkable channel changes have occurred in the Jingjiang Reach of the Middle Yangtze River, since the onset of the Three Gorges Project (TGP). Therefore, it is important to investigate the variations in different fluvial variables, for better understanding of the channel evolution characteristics as an example of the Jingjiang Reach. Recent geomorphic adjustments in the study reach have been investigated quantitatively, including variations in sediment rating curve, fluvial erosion intensity, channel deformation volume and bankfull channel geometry. These fluvial variables adjusted in varying degrees in response to the altered flow and sediment regime caused by the TGP operation. A focus of this study has been especially on variation in the bankfull channel geometry. Calculated bankfull dimensions at section‐ and reach‐scale indicate that: (i) there were significant bank‐erosion processes in local regions without bank‐protection engineering, with empirical relations being developed to reproduce the variation in bankfull widths at four typical sections; (ii) the variation in the reach‐scale channel geometry occurred mainly in the component of bankfull depth, owing to the construction of large‐scale bank‐revetment works, with the depth increasing from 13.7 m in 2002 to 15.0 m in 2014, and with an increase in the corresponding bankfull area of about 11%; and (iii) the reach‐scale bankfull channel dimensions responded to the previous 5‐year average fluvial erosion intensity during flood seasons at Zhicheng, with higher correlations for the depth and area being obtained when calibrated by the measurements in 2002–2012. Furthermore, these relations developed for the section‐ and reach‐scale bankfull channel geometry were also verified by the observed data in 2013–2014, with encouraging results being obtained. Copyright © 2016 John Wiley & Sons, Ltd.     

Stochastic erosion of composite banks in alluvial river bends

The erosion of composite river banks is a complex process involving a number of factors including fluvial erosion, seepage erosion, and cantilever mass failure. To predict the rate of bank erosion with these complexities, a stochastic bank erosion model is suitable to define the probability distribution of the controlling variables. In this study, a bank erosion model in a river bend is developed by coupling several bank erosion processes with an existing hydrodynamic and morphological model. The soil erodibility of cohesive bank layers was measured using a submerged jet test apparatus. Seasonal bank erosion rates for four consecutive years at a bend in the Brahmaputra River, India, were measured by repeated bankline surveys. The ability of the model to predict erosion was evaluated in the river bend that displayed active bank erosion. In this study, different monsoon conditions and the distribution functions of two variables were considered in estimating the stochastic bank erosion rate: the probability of the soil erodibility and stochastic stage hydrographs for the nth return period river stage. Additionally, the influences of the deflection angle of the streamflow, longitudinal slope of river channel, and bed material size on bank erosion rate were also investigated. The obtained stochastic erosion predictions were compared with the observed distribution of the annual‐average bank erosion rate of 45 river bends in the Brahmaputra River. The developed model appropriately predicted the short‐term morphological dynamics of sand‐bed river bends with composite banks. Copyright © 2014 John Wiley & Sons, Ltd.     

Bank erosion and channel width change in a tropical catchment

Catchment sediment budget models are used to predict the location and rates of bank erosion in tropical catchments draining to the Great Barrier Reef lagoon, yet the reliability of these predictions has not been tested due to a lack of measured bank erosion data. This paper presents the results of a 3 year field study examining bank erosion and channel change on the Daintree River, Australia. Three different methods were employed: (1) erosion pins were used to assess the influence of riparian vegetation on bank erosion, (2) bench‐marked cross‐sections were used to evaluate annual changes in channel width and (3) historical aerial photos were used to place the short term data into a longer temporal perspective of channel change (1972–2000). The erosion pin data suggest that the mean erosion rate of banks with riparian vegetation is 6·5 times (or 85%) lower than that of banks without riparian vegetation. The changes measured from cross‐section surveys suggest that channel width has increased by an average of 0·74 (±0·47) m a^?1 over the study period (or ～0·8% yr^?1). The aerial photo results suggest that over the last 30 years the Daintree River has undergone channel contraction of the order of 0·25 m a^?1. The cross‐section data were compared against modelled SedNet bank erosion rates, and it was found that the model underestimated bank erosion and was unable to represent the variable erosion and accretion processes that were observed in the field data. The reach averaged bank erosion rates were improved by the inclusion of locally derived bed slope and discharge estimates; however, the results suggest that it will be difficult for catchment scale sediment budget models to ever accurately predict the location and rate of bank erosion due to the variation in bank erosion rates in both space and time. Copyright © 2008 John Wiley & Sons, Ltd.     

Prediction of tension crack location and riverbank erosion hazards along destabilized channels

Riverbank erosion, associated sedimentation and land loss hazards are a land management problem of global significance and many attempts to predict the onset of riverbank instability have been made. Recently, Osman and Thorne (1988) have presented a Culmann-type analysis of the stability of steep, cohesive riverbanks; this has the potential to be a considerable improvement over previous bank stability theories, which do not account for bank geometry changes due to toe scour and lateral erosion. However, in this paper it is shown that the existing Osman-Thorne model does not properly incorporate the influence of tension cracking on bank stability since the location of the tension crack on the floodplain is indirectly determined via calculation or arbitrary specification of the tension crack depth. Furthermore, accurate determination of tension crack location is essential to the calculation of the geometry of riverbank failure blocks and hence prediction of land loss and bank sediment yield associated with riverbank instability and channel widening. In this paper, a rational, physically based method to predict the location of tension cracks on the floodplain behind the eroding bank face is presented and tested. A case study is used to illustrate the computational procedure required to apply the model. Improved estimates of failure block geometry using the new method may potentially be applied to improve predictions of bank retreat and floodplain land loss along river channels destabilized as a result of environmental change.     

Improving bank erosion modelling at catchment scale by incorporating temporal and spatial variability

Bank erosion can contribute a significant portion of the sediment budget within temperate catchments, yet few catchment scale models include an explicit representation of bank erosion processes. Furthermore, representation is often simplistic resulting in an inability to capture realistic spatial and temporal variability in simulated bank erosion. In this study, the sediment component of the catchment scale model SHETRAN is developed to incorporate key factors influencing the spatio‐temporal rate of bank erosion, due to the effects of channel sinuosity and channel bank vegetation. The model is applied to the Eden catchment, north‐west England, and validated using data derived from a GIS methodology. The developed model simulates magnitudes of total catchment annual bank erosion (617–4063 t y^‐1) within the range of observed values (211–4426 t yr^‐1). In addition, the model provides both greater inter‐annual and spatial variability of bank eroded sediment generation when compared with the basic model, and indicates a potential 61% increase of bank eroded sediment as a result of temporal flood clustering. The approach developed within this study can be used within a number of distributed hydrologic models and has general applicability to temperate catchments, yet further development of model representation of bank erosion processes is required. © 2017 The Authors. Earth Surface Processes and Landforms published by John Wiley & Sons Ltd.