Preparation and properties of electrically conducting textiles by in situ polymerization of poly(3,4‐ethylenedioxythiophene)

Poly(3,4‐ethylenedioxythiophene) (PEDOT) was in situ polymerized on nylon 6, poly(ethylene terephthalate) (PET), and poly(trimethylene terephthalate) (PTT) fabrics using ferric p‐toluenesulfonic acid (FepTS) and ferric chloride (FeCl₃) as oxidants. The effect of the organic solvents used in the polymerization bath was investigated. Prepared PEDOT/nylon 6 composite fabrics have superior electrical conductivity (0.75 S/cm, in ethanol solvent) compared to those of the other PEDOT composite fabrics. In particular, after five cycles of polymerization, the electrical conductivity of the composite fabric reached about 2 S/cm. However, the nylon 6 fabric was damaged by EDOT radical cations and the strong acidity of FepTS during the polymerization process. It was concluded that PTT fabric, which has excellent elastic recovery and acid resistance, is a suitable substrate for in situ polymerization of PEDOT, because the PEDOT/PTT composite fabric was hardly damaged during the polymerization process and its electrical conductivity is comparatively good (0.36 S/cm, in butanol solvent). © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1326–1332, 2005     

Synthesis of poly(3,4‐ethylenedioxythiophene) nanoparticles via chemical oxidation polymerization

Poly(3,4‐ethylenedioxythiophene) (PEDOT) nanoparticles were synthesized via chemical oxidation polymerization using 3,4‐ethylenedioxythiophene as the starting monomer and ammonium peroxydisulfate (APS) as the oxidant. The effects of APS concentration, surfactant concentration and type of surfactant, namely dodecylbenzenesulfonic acid and sodium dodecylsulfate, were investigated. Distinct particle shapes were obtained: irregular, raspberry agglomerate, coralliform, orange‐peel, globular and plum shapes. The particle sizes and the electrical conductivity are in the ranges 60 to 900 nm and <1 to 153 S cm^?1, respectively, depending on the polymerization conditions. PEDOT synthesis in the absence of a surfactant yields a smaller particle size because a larger amount of initiator induces lower molecular weights and smaller PEDOT particles. The smaller PEDOT particles correspond to higher electrical conductivity because of the larger surface areas for electron transfer and a smaller amount of obstructing surfactant aliphatic segments. Moreover, particle size and shape can be varied, depending on surfactant type and concentration which dictate the micellar shapes in the polymerization reaction. This work is focused on the tailor‐made PEDOT shape and property relationship under synthesis conditions where several shapes have not been previously seen. © 2013 Society of Chemical Industry     

Effects of thermal imidization on mechanical properties of poly(amide‐co‐imide)/multiwalled carbon nanotube composite films

In this study, experimental and numerical studies were performed to investigate the relationship among the functionalization method, weight fraction of MWCNTs, thermal imidization cycle, and mechanical properties of various PAI/MWCNT composite films. Poly(amide‐co‐imide)/multiwalled carbon nanotube composite films were prepared by solution mixing and film casting. The effects of chemical functionalization and weight fraction of multiwalled carbon nanotubes on thermal imidization and mechanical properties were investigated through experimental and numerical studies. The time needed to achieve sufficient thermal imidization was reduced with increasing multiwalled carbon nanotube content when compared with that of a pure poly(amide‐co‐imide) film because multiwalled carbon nanotubes have a higher thermal conductivity than pure poly(amide‐co‐imide) resin. Mechanical properties of pure poly(amide‐co‐imide) and poly(amide‐co‐imide)/multiwalled carbon nanotube composite films were increased with increasing imidization time and were improved significantly in the case of the composite film filled with hydrogen peroxide treated multiwalled carbon nanotubes. Both the tensile strength and strain to failure of the multiwalled carbon nanotube filled poly(amide‐co‐imide) film were increased substantially because multiwalled carbon nanotube dispersion was improved and covalent bonding was formed between multiwalled carbon nanotubes and poly(amide‐co‐imide) molecules. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Effective electrochemically controlled process for perchlorate removal using poly(aniline‐co‐o‐aminophenol)/multiwalled carbon nanotubes

The study on perchlorate removal from simulated wastewater was carried out using a conducting copolymer poly(aniline‐co‐o‐aminophenol) (PANOA) polymerized on multiwalled carbon nanotubes (MWNTs)‐modified glassy carbon (GC) electrode. The cyclic voltammograms demonstrated that the PANOA/MWNTs GC electrode in a NaCl solution containing NaClO₄ had a good redox activity, reversibility, and stability in a wide range of pHs tested (from pH <1 to 9.0). The ratio of ClO/Cl^? in PANOA/MWNTs was up to 80.8%, which was 10.0% in the solution, indicating that PANOA/MWNTs had a relatively high affinity to perchlorate. The result of X‐ray photoelectron spectroscopy revealed a fact that Cl^? ions can be strongly adsorbed on MWNTs, which resulted in an improvement in the electrical activity of PANOA and perchlorate removal. Therefore, it is possible to develop a green process for removing perchlorate from wastewater using PANOA/MWNTs. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Mechanical reinforcement of poly(1‐butene) using polypropylene‐grafted multiwalled carbon nanotubes

The mechanical properties of poly(1‐butene) reinforced by pristine multiwalled carbon nanotubes (MWNTs) and polypropylene‐grafted MWNTs (PP‐g‐MWNTs) were evaluated. The incorporation of pristine MWNTs to PB led to an improvement in stiffness, but not in strength, ductility, and toughness. In comparison, PP‐g‐MWNTs were able to improve the stiffness, strength, and toughness of PB significantly, without compromising the ductility. The mechanical properties of PB improved with increasing amount of PP‐g‐MWNTs up to an effective MWNT content of 1.5 wt%. Further increase in the effective MWNT content led to a downturn in mechanical properties due to the existence of MWNTs bundles as observed by microscopy. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis and properties of polymer from bis‐3,4‐ethylenedioxythiophene substituted acenaphthenequinoxaline

A new electrochoromic polymer poly(8,11‐bis(3,4‐ethylenedioxy thiophen‐2‐yl)acenaphtho[1,2‐b]‐quinoxaline) (PBEAQ) was synthesized by electrochemical polymerization of the corresponding monomer (BEAQ) in a 0.1 M tetraethylammonium tetrafluoroborate (TEABF₄) dichloromethane–acetonitrile (2 : 1, v : v) solution. The monomer and polymer were characterized by elemental analysis, ¹H‐NMR, IR, and UV‐vis spectroscopy. The electrochemical and optical properties of polymer were investigated by cyclic voltammetry and UV‐vis spectroscopy. Cyclic voltammetry and spectroelectrochemistry studies demonstrated that the polymer can be reversibly reduced and oxidized (both n‐ and p‐doped) between ?2 V and +1.5 V vs. Ag/Ag⁺. The polymer had a transmissive light blue color in the oxidized state and reddish color in the reduced state. Undoped polymer shows UV‐vis absorption peaks at 615 nm in solution, 650 nm in solid state, and has an optical band gap of 1.5 eV. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Effects of alcoholic solvents on the conductivity of tosylate‐doped poly(3,4‐ethylenedioxythiophene) (PEDOT‐OTs)

The effects of alcoholic solvents on the charge transport properties of tosylate‐doped poly(3,4‐ethylenedioxythiophene) (PEDOT‐OTs) are investigated. The use of different alcoholic solvents in the oxidative chemical polymerization of 3,4‐ethylenedioxythiophene (EDOT) with iron(III)‐p‐tosylate led to a change in the electrical conductivity of PEDOT‐OTs. For example, PEDOT‐OTs prepared from methanol shows a conductivity of 20.1 S cm^?1 which is enhanced by a factor of 200 as compared to PEDOT‐OTs prepared from hexanol. The variation of charge transport properties on the use of different alcoholic solvents is consistent with the data recorded by UV‐visible and electrospin resonance (ESR) measurements. From XPS experiments, the PEDOT‐OTs samples prepared from different alcoholic solvents were found to have almost the same doping level, suggesting that the number of charge carriers is not responsible for the change in conductivity. Supported by XRD results, it was found that the use of alcoholic solvents with shorter chain length induces more efficient packing of PEDOT chains. It is proposed that the alcoholic solvents associated with the counter ion of PEDOT via hydrogen bonding give rise to a change in the molecular ordering of PEDOT chains during the polymerization step, hence enhancing or depressing the inter‐chain hopping rate of the resulting PEDOT‐OTs. Copyright © 2005 Society of Chemical Industry     

Preparation and characterization of multi‐walled carbon nanotubes/polymer gradient composite films

BACKGROUND: Recently, much work has focused on the efficient dispersion of carbon nanotubes (CNTs) throughout a polymer matrix for mechanical and/or electrical enhancement. However, there are still only few reports about gradient distribution of CNTs in polymer matrices. In the work reported here, CNTs embedded in a polymer film with a gradient distribution were successfully obtained and studied. RESULTS: For composite films with gradient distributions of CNTs, the upper surface behaves as an intrinsic insulator, while the lower one behaves as a semiconductor, or even as a conductor. It is also found that with an increase of 1 wt% CNTs, the resistance of the bottom surface decreases by 2–3 orders of magnitude, as compared with pure polyarylene ether nitrile; furthermore, when the proportion of CNTs increases up to 5 wt%, the resistance of the bottom surface shows only very little change. As a result, sufficient matrix conductivity of the bottom surface could be achieved at a lower filler concentration with CNTs in a gradient distribution. Meanwhile, the thermal stability, glass transition temperature and tensile properties of the matrix are maintained. CONCLUSION: There is considerable interest in such gradient composite films, which could be applied in the electrical engineering, electronics and aerospace fields, for their excellent mechanical properties, thermal stability and novel electrical properties. Copyright © 2008 Society of Chemical Industry     

In situ polymerization and photophysical properties of poly(p‐phenylene benzobisoxazole)/multiwalled carbon nanotubes composites

Poly(p‐phenylene benzobisoxazole)/multiwalled carbon nanotubes (PBO‐MWCNT) composites with different MWCNT compositions were prepared through in situ polymerization of PBO in the presence of carboxylated MWCNTs. The nanocomposite's structure, thermal and photophysical properties were investigated and compared with their blend counterparts (PBO/MWCNT) using Fourier transform infrared spectra, Raman spectra, Wide‐angle X‐ray diffraction, thermogravimetric analysis, UV‐vis absorption, and photoluminescence. The results showed that MWCNTs had a strong interaction with PBO through covalent bonding. The incorporation of MWCNTs increased the distance between two neighboring PBO chains and also improved the thermal resistance of PBO. The investigation of UV‐vis absorption and fluorescence emission spectra exhibited that in situ PBO‐MWCNT composites had a stronger absorbance and obvious trend of red‐shift compared with blend PBO/MWCNT composites for all compositions. This behavior can be attributed to the efficient energy transfer through forming conjugated bonding interactions in the PBO‐MWCNT composites. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Nucleation effect of hydroxyl‐purified multiwalled carbon nanotubes in poly(p‐phenylene sulfide) composites

To investigate the nucleation effect of hydroxyl‐purified multiwalled carbon nanotubes (MWNTs‐OH) in poly(p‐phenylenesulfide) (PPS), a series of composites were prepared by blending PPS with MWNTs‐OH at 1, 2, and 3 wt %, respectively. Under SEM observation MWNTs‐OH were found homogeneously dispersed in the PPS matrix. DSC thermograms revealed that the enthalpy (ΔH_c) of the composites increased with increasing MWNT‐OH content, whereas the crystallization temperature (T_c) decreased progressively. The decrease in T_c was in accordance with the smaller crystallite size determined with WXRD characterization, and the increase in ΔH_c was evidenced by FTIR and XPS analyses. The higher ΔH_c shows that MWNTs‐OH serves as a nucleating agent, providing sufficiently multiplied sites for crystal growth. The lowering of T_c was attributed not only to MWNTs‐OH network hindrance to PPS chain fusing rearrangement, but also to a poorer affinity between MWNTs‐OH and PPS; both effects coordinately govern T_c of PPS/MWNTs‐OH composites. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Transferring polypropylene into carbon nanotubes via combustion of PP/zeolites (H‐ZSM‐5 or H‐beta)/Ni2O3

In a simple device, two kinds of zeolites were successfully used as synergistic additive to promote formation of the multi‐walled carbon nanotubes (MWNTs) from polypropylene (PP) via combustion. More importantly, this kind of process may potentially act as a new approach for recycling plastic wastes, because it could effectively transfer polyolefin wastes into valuable carbon materials. Experimental results demonstrated that the higher quality of MWNTs can be obtained from the mixture (PP/H‐Beta/Ni₂O₃) than that from the mixture (PP/H‐ZSM‐5/Ni₂O₃). At the same time, the yield of MWNTs from PP/H‐ZSM‐5/Ni₂O₃ system is much lower than that from PP/H‐Beta/Ni₂O₃ under the same condition. The reason for the different effects of both types of zeolites on the morphology and the yield of the MWNTs was analyzed. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Poly (N‐methylaniline)/multi‐walled carbon nanotube composites—Synthesis,characterization, and electrical properties

This study described the synthesis of hydrochloric acid (HCl)‐doped poly (N‐methylaniline) (PNMA) with carboxylic groups containing multi‐walled carbon nanotubes (c‐MWNTs) via in situ polymerization. Based on the π–π electron interaction between c‐MWNTs and the N‐methylaniline monomer and the hydrogen bond interaction between the carboxyl groups of c‐MWNTs and imine groups of N‐methylaniline monomers, N‐methylaniline molecules were adsorbed on the surface of c‐MWNTs and polymerized to form PNMA/c‐MWNT composites. Scanning electron microscopy images showed that both the thinner fibrous phase and the larger block phase could be observed. The individual fibrous phases had diameters from several tens to hundreds of nanometers, depending on the PNMA content. Transmission electron microscopy proved that PNMA/c‐MWNTs composite fibrous phases were core (c‐MWNT)‐shell (PNMA) tubular structures. The structure of PNMA/c‐MWNT composites was characterized by FTIR, UV–vis spectra, and X‐ray diffraction patterns. The electrical conductivities of PNMA/c‐MWNT composites were much higher than that of PNMA without c‐MWNTs. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2356–2361, 2006     

Comparative study of poly(vinyl alcohol)‐based support materials for the immobilization of glucose oxidase

BACKGROUND: The performances of four types of glucose oxidase (GOD) immobilization materials based on poly(vinyl alcohol) (PVA) were compared. The matrices of interest were chemically‐linked PVA, freeze‐thawed PVA cryogel, tetramethoxysilane (TMOS) sol‐gel‐PVA hybrid material, and alumina sol‐gel‐PVA hybrid material. RESULTS: Overall, the membranes showed good sensitivity except for the chemically cross‐linked PVA. However, the main differences with the enzyme immobilization methods were enzyme leakage and values of K_m^app. CONCLUSION: Freeze‐thawed PVA‐GOD membranes and TMOS‐PVA, which showed satisfactory sensitivity and adequate value of K_m^app, were quite promising as support materials for immobilizing GOD. Copyright © 2007 Society of Chemical Industry     

Preparation and characterization of poly(vinylidene fluoride) nanocomposites containing multiwalled carbon nanotubes

Poly(vinylidene fluoride) (PVDF) nanocomposites with different loadings of multiwalled carbon nanotubes (MWNT) were prepared by melt‐compounding technique. A homogeneous dispersion of MWNT throughout PVDF matrix was observed on the cryo‐fractured surfaces by scanning electron microscopy. Thermogravimetric analysis results indicated that the thermal stability of neat PVDF was improved with the incorporation of MWNT. Dynamic mechanical analysis showed a significant improvement in the storage modulus over a temperature range from ?125 to 75°C with the addition of MWNT. The melt‐rheological studies illustrated that incorporating MWNT into PVDF matrix resulted in higher complex viscosities (|η*|), storage modulus (G′), loss modulus (G″), and lower loss factor (tan δ) than those of neat PVDF. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Morphology,crystallization, and mechanical properties of poly(ethylene terephthalate)/multiwalled carbon nanotubes composites

Poly(ethylene terephthalate)/multiwalled carbon nanotubes (PET/MWCNTs) with different MWCNTs loadings have been prepared by in situ polymerization of ethylene glycol (EG) containing dispersed MWCNTs and terephthalic acid (TPA). From scanning electronic microscopy images of nanocomposites, it can be clearly seen that the PET/MWCNTs composites with low‐MWCNTs contents (0.2 and 0.4 wt %) get better MWCNTs dispersion than analogous with high‐tube loadings (0.6 and 0.8 wt %). The nonisothermal crystallization kinetics was analyzed by differential scanning calorimetry using Mo kinetics equation, and the results showed that the incorporation of MWCNTs accelerates the crystallization process obviously. Mechanical testing shows that, in comparison with neat PET, the Young's modulus and the yield strength of the PET nanocomposites with incorporating 0.4 wt % MWCNTs are effectively improved by about 25% and 15%, respectively. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Fabrication of poly(3,4‐ethylenedioxythiophene)‐polysaccharide composites

Poly(3,4‐ethylenedioxythiophene) (PEDOT) doped with a series of anionic polysaccharides such as carboxymethyl cellulose, sodium hyaluronate, xanthan gum, pectin, gellan gum were prepared by electropolymerization in aqueous solutions. Some other dopants of potassium nitrate, potassium sulfate, sodium poly(styrenesulfonate), and sodium polyacrylate were used in comparison with the anionic polysaccharides. The electrochemical properties and stability of the obtained PEDOT films were also investigated. It was found that indium tin oxide (ITO) conductive glass could be used as the working electrode of the electropolymerization of EDOT and that the dopant had a great influence on polymerization potential and overoxidation potential. These charged biomolecules of anionic polysaccharides were found to facilitate electropolymerization of EDOT instead of common doping anions as counterion. The electroactive PEDOT films doped with anionic polysaccharides showed stable electrochemical properties, good texture, and adhesion properties to the ITO conductive glass. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Crystallization behavior of poly(ethylene terephthalate)/multiwalled carbon nanotubes composites

Crystallization behavior of poly(ethylene terephthalate)/multiwalled carbon nanotubes (PET/MWNTs) composites have been investigated under isothermal conditions and in comparison with the conventional nucleating agents, sodium benzoate, and micrometric carbon/glass fibers. In the PET/MWNTs composites, MWNTs promote the crystallization of PET as a heterogeneous nucleating agent, and the nucleation efficiency is greatly enhanced when MWNTs was homogeneously dispersed in PET matrix. In comparison with pure PET, spherulites size of PET/MWNTs composites is significantly reduced, and the shape becomes quite irregular. TEM images indicate that MWNTs bundles locate in the center of spherulites of PET and act as nuclei. Fold surface free energy during nucleation process for MWNTs nucleated PET is just half of pure PET, suggesting that MWNTs are efficient nucleating agents for PET. The sequence of nucleating ability of is given as follows: sodium benzoate>MWNTs>talc>carbon fibers≈glass fibers. The nucleation in the presence of sodium benzoate is a chemical nucleation process that may cause severe degradation of PET, but MWNTs nucleate PET through “particle effect,” which does not affect the molecular weight of PET. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Functionalization of multiwalled carbon nanotubes with amphiphilic poly(aspartic acid)

A new method to functionalize multiwalled carbon nanotubes (MWNTs) with amphiphilic poly(aspartic acid) was investigated. The amphiphilic polymer (PASP‐C16) was synthesized by thermal condensation and aminolysis by hexadecylamine, followed by hydrolysis of the remaining succinimide units in the polymer backbone. The functionalization of MWNTs was achieved by physical adsorption of the biopolymer onto the surfaces of MWNTs. Ultraviolet‐visible ( UV‐vis) spectra showed that the functionalized MWNTs had a good aqueous dispersity and solubility. The interaction of PASP‐C16 with MWNTs was investigated by analyzing X‐ray diffraction (XRD) patterns, circular dichroism (CD), spectra and high‐resolution transmission electron microscopy ( HRTEM ). From the XRD patterns, it can be known that the aggregate of PASP‐C16 due to intermolecular interaction between hexadecyl chains has been reduced when the polymer interacting with MWNTs. CD spectra indicated that the interaction of hexadecyl chains of PASP‐C16 with the wall of MWNTs is the major interaction between PASP‐C16 and MWNTs, and MWNTs were covered by the poly(aspatic acid) backbone. © 2010 American Institute of Chemical Engineers AIChE J, 2011     

Thermal degradation behaviour of multi‐walled carbon nanotube‐reinforced poly(L‐lactide) nanocomposites

BACKGROUND: Polymer/multi‐walled carbon nanotube (MWCNT) composites are one of the most promising alternatives to conventional polymer composites filled with micrometre‐sized fillers. This approach can also be applied for the improvement of mechanical properties and thermal stability of biodegradable aliphatic polyesters, such as poly(L ‐lactide) (PLLA), which have been receiving increasing attention due to environmental concerns. Thermal degradation behaviour provides useful information for the determination of the optimum processing conditions and for identification of potential applications of final products. RESULTS: The PLLA/MWCNT composites investigated showed a higher thermal degradation peak temperature and onset temperature of degradation along with a higher amount of residue at the completion of degradation than neat PLLA. Moreover, PLLA/MWCNT composites with a greater MWCNT content showed higher activation energy of thermal degradation than those with a lower MWCNT loading, which confirmed the positive effect of MWCNT incorporation on the enhancement of PLLA thermal stability. CONCLUSION: This study explored the thermal degradation behaviour of PLLA/MWCNT composites by observing the weight loss, molecular weight and mechanical properties during non‐isothermal and isothermal degradation. The incorporation of MWCNTs into the PLLA matrix enhanced considerably the mechanical properties and thermal stability. Copyright © 2009 Society of Chemical Industry     

Synthesis and electrochemical capacitance of core-shell poly (3,4-ethylenedioxythiophene)/poly (sodium 4-styrenesulfonate)-modified multiwalled carbon nanotube nanocomposites

A noncovalent method was used to functionalize multiwalled carbon nanotubes with poly (sodium 4-styrene sulfonate). And then, the core-shell poly (3,4-ethylenedioxythiophene)/functionalized multiwalled carbon nanotubes (PEDOT/PSS-CNTs) nanocomposite was successfully realized via in situ polymerization under the hydrothermal condition. In the process, PSS served for not only solubilizing and dispersing CNTs well into an aqueous solution, but also tethering EDOT monomer onto the surface of CNTs to facilitate the formation of a uniform PEDOT coating. Fourier transform infrared spectroscopy (FT-IR) and transmission electron microscopy (TEM) were used to characterize the resultant PEDOT/PSS-CNTs. In addition, the PEDOT/PSS-CNTs nanocomposite (50 wt.% PEDOT) had a specific capacitance (SC) of 198.2 F g⁻¹ at a current density of 0.5 A g⁻¹ and a capacitance degradation of 26.9% after 2000 cycles, much better than those of pristine PEDOT and PEDOT/CNTs (50 wt.% PEDOT). The enhanced electrochemical performance of the PEDOT/PSS-CNTs nanocomposite (50 wt.% PEDOT) should be attributed to the high uniform system of the nanocomposite, resulting in the large surface easily contacted by abundant electrolyte ions through the three-dimensional conducting matrix.