Structural and electrochemical properties of a porous nanostructured SnO2 film electrode for lithium-ion batteries

A B₂O₃-doped SnO₂ thin film was prepared by a novel experimental procedure combining the electrodeposition and the hydrothermal treatment, and its structure and electrochemical properties were investigated by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) analysis, energy dispersive X-ray (EDX) spectroscopy and galvanostatic charge–discharge tests. It was found that the as-prepared modified SnO₂ film shows a porous network structure with large specific surface area and high crystallinity. The results of electrochemical tests showed that the modified SnO₂ electrode presents the largest reversible capacity of 676 mAh g^?1 at the fourth cycle, close to the theoretical capacity of SnO₂ (790 mAh g^?1); and it still delivers a reversible Li storage capacity of 524 mAh g^?1 after 50 cycles. The reasons that the modified SnO₂ film electrode shows excellent electrochemical properties were also discussed.     

Fabrication and electrochemical performance of nickel ferrite nanoparticles as anode material in lithium ion batteries

Nano-sized nickel ferrite (NiFe₂O₄) was prepared by hydrothermal method at low temperature. The crystalline phase, morphology and specific surface area (BET) of the resultant samples were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM) and nitrogen physical adsorption, respectively. The particle sizes of the resulting NiFe₂O₄ samples were in the range of 5–15 nm. The electrochemical performance of NiFe₂O₄ nanoparticles as the anodic material in lithium ion batteries was tested. It was found that the first discharge capacity of the anode made from NiFe₂O₄ nanoparticles could reach a very high value of 1314 mAh g⁻¹, while the discharge capacity decreased to 790.8 mAh g⁻¹ and 709.0 mAh g⁻¹ at a current density of 0.2 mA cm⁻² after 2 and 3 cycles, respectively. The BET surface area is up to 111.4 m² g⁻¹. The reaction mechanism between lithium and nickel ferrite was also discussed based on the results of cycle voltammetry (CV) experiments.     

Suppression of dendritic lithium formation by using concentrated electrolyte solutions

This study examined the electrochemical deposition and dissolution of lithium on nickel electrodes in a propylene carbonate (PC) electrolyte containing different LiN(SO₂C₂F₅)₂ concentrations. The electrolyte concentration was found to have a significant effect on the reactions occurring at the electrode. The poor cycleability of the electrodes in the low-concentration solutions was improved considerably by increasing the electrolyte concentration. Transmission electron microscopy (TEM) revealed that a high-concentration solution produces a thinner solid electrolyte interphase (SEI) on the electrodeposited lithium than a low-concentration solution, e.g., ∼35 nm in 1.28 mol kg⁻¹ vs. ∼20 nm in 3.27 mol kg⁻¹ solutions. Raman spectroscopy showed that the solvation number of lithium ions differed according to the electrolyte concentration. This suggests that the structure of solvated lithium ions is an important factor in suppressing dendritic lithium formation.     

Asymmetric electrochemical capacitor microdevice designed with vanadium nitride and nickel oxide thin film electrodes

Vanadium nitride thin film has been coupled with electrodeposited nickel oxide in order to design an electrochemical capacitor microdevice. VN has been used as negative electrode while NiO was used as the positive one in 1 M KOH electrolyte. VN exhibits a pseudo-capacitive behavior while NiO shows a faradaic behavior. This asymmetric microdevice has been operated between 0.5 and up to 1.8 V in aqueous based electrolyte (1 M KOH). Long term cycling ability (10,000 charge/discharge cycles) has been demonstrated with interesting energy (1.0 μW h cm^− 2) and power (40 mW cm^− 2) densities.     

Hydrogen bubble dynamic template synthesis of porous gold for nonenzymatic electrochemical detection of glucose

Gold (Au) films with open interconnected macroporous walls and nanoparticles have been successfully sculptured using the hydrogen bubble dynamic template synthesis followed by a galvanic replacement reaction. Copper (Cu) films with open interconnected macroporous walls and nanoparticles were synthesized using the electrochemically generated hydrogen bubbles as a dynamic template. Then through a galvanic replacement reaction between the porous Cu sacrificial templates and KAu(CN)₂ in solution, the porous Cu films were converted to porous Au films with the similar morphologies. Additional electrochemical dealloying process was introduced to remove the remaining Cu from the porous Au films. X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), Energy-dispersive X-ray (EDX), X-ray diffraction (XRD) and electrochemical methods were adopted to characterize the porous Au films. The resulted porous Au films show excellent catalytic activity toward the electrooxidation of glucose. A nonenzymatic glucose sensor based on those Au film electrodes shows a linear range from 2 to 10 mM with a sensitivity of 11.8 μA cm⁻² mM⁻¹, and a detection limit of 5 μM.     

Hierarchically ordered porous nickel oxide array film with enhanced electrochemical properties for lithium ion batteries

Hierarchically ordered porous nickel oxide array film was prepared by electrodeposition through monolayer polystyrene spheres template. The as-prepared film had a highly porous structure of interconnected macrobowls array possessing nanopores. As anode material for lithium ion batteries, the porous array NiO film exhibited weaker polarization, higher coulombic efficiency and better cycling performance in comparison with the dense NiO film. After 50 cycles, the discharge capacity of porous array NiO film was 518 mAh g^? 1 at 1 C rate, higher than that of the dense NiO film (287 mAh g^? 1). The enhancement of the electrochemical properties was due to the unique hierarchical porous architecture, which provided fast ion/electron transfer and alleviated the structure degradation during the cycling process.     

Using flowerlike polymer–copper nanostructure composite and novel organic–inorganic hybrid material to construct an amperometric biosensor for hydrogen peroxide

A new type of amperometric hydrogen peroxide biosensor was fabricated by entrapping horseradish peroxidase (HRP) in the organic–inorganic hybrid material composed of zirconia–chitosan sol–gel and Au nanoparticles (ZrO₂–CS–AuNPs). The sensitivity of the biosensor was enhanced by a flowerlike polymer–copper nanostructure composite (pPA–FCu) which was prepared from co-electrodeposition of CuSO₄ solution and 2,6-pyridinediamine solution. Several techniques, including UV–vis absorption spectroscopy, scanning electron microscopy, cyclic voltammetry, chronoamperometry and electrochemical impedance spectroscopy were employed to characterize the assembly process and performance of the biosensor. The results showed that this pPA–FCu nanostructure not only had excellent redox electrochemical activity, but also had good catalytic efficiency for hydrogen peroxide. Also the ZrO₂–CS–AuNPs had good film forming ability, high stability and good retention of bioactivity of the immobilized enzyme. The resulting biosensors showed a linear range from 7.80 × 10^?7 to 3.7 × 10^?3 mol L^?1, with a detection limit of 3.2 × 10^?7 mol L^?1 (S/N = 3) under optimized experimental conditions. The apparent Michaelis–Menten constant was determined to be 0.32 mM, showing good affinity. In addition, the biosensor which exhibits good analytical performance, acceptable stability and good selectivity, has potential for practical applications.     

Electrodeposited PbO2 thin film on Ti electrode for application in hybrid supercapacitor

PbO₂ thin films were prepared by pulse current technique on Ti substrate from Pb(NO₃)₂ plating solution. The hybrid supercapacitor was designed with PbO₂ thin film as positive electrode and activated carbon (AC) as negative electrode in the 5.3 M H₂SO₄ solution. Its electrochemical properties were determined by cyclic voltammetry (CV), charge–discharge test and electrochemical impedance spectroscopy (EIS). The results revealed that the PbO₂/AC hybrid supercapacitor exhibited large specific capacitance, high-power and stable cycle performance. In the potential range of 0.8–1.8 V, the hybrid supercapacitor can deliver a specific capacitance of 71.5 F g^?1 at a discharge current density of 200 mA g^?1(4 mA cm^?2) when the mass ratio of AC to PbO₂ was three, and after 4500 deep cycles, the specific capacitance remains at 64.4 F g^?1, or 32.2 Wh Kg^?1 in specific energy, and the capacity only fades 10% from its initial value.     

Electrochemical fabrication of novel fluorescent polymeric film: Poly(pyrrole–pyrene)

We describe herein the electrochemical characterization and polymerization of 4-pyren-1-yl-butyric acid 11-pyrrol-1-yl-decyl ester (pyrrole–pyrene) in CH₃CN. The electrochemical oxidation of the pyrrole group at 0.77 V vs Ag/Ag + 10 mM in CH₃CN led to the first example of a fluorescent polypyrrole film. The mechanism of deposition on platinum electrode was studied by voltammetry and chronoamperometry. The optical properties of the polymeric films electrogenerated on ITO electrodes were examined by UV–visible spectroscopy and fluorescence microscopy indicating an increase in fluorescence properties by increased polymer thickness. The electrochemical oxidation of pyrenyl group linked to the polypyrrole backbone was carried out at 1.2 V. This additional polymerization was demonstrated by UV–visible spectroscopy and induced the loss of the fluorescence properties of the resulting polymeric film.     

Nanoparticles of nickel oxide and nickel hydroxide using lyophilisomes of fibrinogen as template

Stable lyophilisomes of fibrinogen at pH 7.5 have been prepared by the method of a rapid freezing–heating and annealing sequence. Reduction of the lyophilisomes of the nickel–fibrinogen complex coated on solid substrates and subsequent heating showed formation of nickel hydroxide and finally nickel oxide. Ultraviolet–visible spectroscopy has been used to monitor the thin films of pure fibrinogen microcapsules, as well as the subsequent nucleation and growth of nanoparticles within the supramolecular structure. Transmission electron microscopy showed initially a thread-like structure which disappeared on continued heating, resulting in nanoparticles ranging from 10 to 50 nm. Particle-size distribution of product was analyzed by using X-ray diffraction (XRD), transmission electron microscopy (TEM) and the corresponding selected area electron diffraction (SAED), and Brunauer–Emmett–Teller (BET) N₂ adsorption. The results suggest that the NiO particles have a body-centered cubic structure and are well dispersed. The particle-size distribution ranges from 10 to 50 nm with an average particle size about 28 nm, and the specific surface area is 34 m²/g. Magnetic study carried out on the prepared nanoparticles showed a ferromagnetic behavior.     

Electrochemical properties of Li(Li(1−x)/3CoxMn(2−2x)/3)O2 (0 ⩽ x ⩽ 1) solid solutions prepared by poly-vinyl alcohol (PVA) method

The whole range of solid solutions Li(Li_(1−x)/3Co_xMn_(2−2x)/3)O₂ (0 ⩽ x ⩽ 1) was firstly synthesized by an aqueous solution method using poly-vinyl alcohol as a synthetic agent to investigate their structure and electrochemical properties. X-ray diffraction results indicated that the synthesized solid solutions showed a single phase without any detectable impurity phase and have a hexagonal structure with some additional peaks caused by monoclinic distortion, especially in the solid solutions with a low Co amount. In the electrochemical examination, the solid solutions in the range between 0.2 ⩽ x ⩽ 0.9 showed higher discharge capacity and better cyclability than LiCoO₂ (x = 1) on cycling between 2.0 and 4.6 V with 100 mA g⁻¹ at 25 °C. For example, Li(Li_0.2Co_0.4Mn_0.4)O₂ (x = 0.4) exhibited a high discharge capacity of 180 mA h g⁻¹ at the 50th cycle. By synthesizing the solid solution between Li₂MnO₃ and LiCoO₂, the electrochemical properties of the end members were improved.     

Electrochemical supercapacitor application of pervoskite thin films

We have explored electrochemically deposited pervoskite nanocrystalline porous bismuth iron oxide (BiFeO₃) thin film electrode from alkaline bath for electrochemical supercapacitors. The pervoskite BiFeO₃ nanocrystalline thin film electrode showed comparable specific capacitance of 81 F g⁻¹ and electrochemical supercapacitive performance and stability in an aqueous NaOH electrolyte to that of commonly used ruthenium based pervoskites.     

A combined electrochemical route to fabricate large-area and free-standing inverse opaline film

A combined electrochemical route involving electrophoresis and electrodeposition is developed to fabricate a large-area unsupported nickel inverse opaline film with thickness less than 10 μm. A vertical electrophoresis allows for the packing of 495 nm polystyrene microspheres on an ITO-coated glass to form a colloidal crystal with significantly reduced defects. Subsequently, a nickel electrodeposition is employed to fill the interstitial voids among the close-packed polystyrene microspheres, followed by the removal of the colloidal template in a two-stage process, leaving a robust nickel skeleton with hexagonally arranged pores and interconnected pore channels. This nickel skeleton is then detached from the ITO-coated glass via a liquid nitrogen treatment, rendering a free-standing nickel inverse opaline film in 2 × 2 cm². Porometer measurements indicate a narrow pore size distribution consistent with images from scanning electron microscope. We determine that the intensity ratio of (111)/(100) diffraction peak is an indicator for the strength of the Ni inverse opals, and thus affects its structural integrity upon detachment from the ITO-coated glass.     

A study on solution deposited CuSCN thin films: Structural,electrochemical, optical properties

A cost-effective successive ionic layer adsorption and reaction (SILAR) method was used to deposit copper (I) thiocyanate (CuSCN) thin films on glass and steel substrates for this study. The deposited thin films were characterized for their structural, morphological, optical and electrochemical properties using X-ray diffraction (XRD), scanning electron microscopy (SEM), UV–visible spectroscopy and VersaSTAT potentiostat. A direct band gap of 3.88 eV and 3.6 eV with film thickness of 0.7 μm and 0.9 μm was obtained at 20 and 30 deposition cycles respectively. The band gap, microstrain, dislocation density and crystal size were observed to be thickness dependent. The specific capacitance of the CuSCN thin film electrode at 20 mV/s was 760 F g⁻¹ for deposition 20 cycles and 729 F g⁻¹ for deposition 30 cycles.     

Synthesis of nanoporous activated iridium oxide films by anodized aluminum oxide templated atomic layer deposition

Iridium oxide (IrOx) has been widely studied due to its applications in electrochromic devices, pH sensing, and neural stimulation. Previous work has demonstrated that both Ir and IrOx films with porous morphologies prepared by sputtering exhibit significantly enhanced charge storage capacities. However, sputtering provides only limited control over film porosity. In this work, we demonstrate an alternative scheme for synthesizing nanoporous Ir and activated IrOx films (AIROFs). This scheme utilizes atomic layer deposition to deposit a thin conformal Ir film within a nanoporous anodized aluminum oxide template. The Ir film is then activated by potential cycling in 0.1 M H₂SO₄ to form a nanoporous AIROF. The morphologies and electrochemical properties of the films are characterized by scanning electron microscopy and cyclic voltammetry, respectively. The resulting nanoporous AIROFs exhibit a nanoporous morphology and enhanced cathodal charge storage capacities as large as 311 mC/cm².     

A Li3V2(PO4)3/C thin film with high rate capability as a cathode material for lithium-ion batteries

A monoclinic lithium vanadium phosphate (Li₃V₂(PO₄)₃) and carbon composite thin film (LVP/C) is prepared via electrostatic spray deposition. The film is studied with X-ray diffraction, scanning and transmission electron microscopy and galvanostatic cell cycling. The LVP/C film is composed of carbon-coated Li₃V₂(PO₄)₃ nanoparticles (50 nm) that are well distributed in a carbon matrix. In the voltage range of 3.0–4.3 V, it exhibits a reversible capacity of 118 mA h g^?1 and good capacity retention at the current rate of 1 C, while delivers 80 mA h g^?1 at 24 C. These results suggest a practical strategy to develop new cathode materials for high power lithium-ion batteries.     

Self-healing characteristic of praseodymium conversion coating on AZNd Mg alloy studied by scanning electrochemical microscopy

Application of rare earth conversion coatings as a surface treatment for magnesium has been the subject of several studies revealing the potential to act as an effective passivating layer. Herein a mechanistic study is presented on the formation of a rare earth conversion layer based on Pr(NO₃)₃ on AZ80X magnesium alloy in simulated biological (buffered) solution. Scanning electrochemical microscopy (SECM) was used to investigate the insulating properties and degradation behaviour of the Pr conversion layer. The self-healing properties of the conversion layer in the presence of Pr^3 + were also studied using SECM. Results revealed the self-healing characteristic of the Pr conversion film in the presence of active, Pr^3 +, species. The Pr conversion layer provided passivation in the short term by producing an electrochemically inert and insulating layer. SECM results in potentiometric mode elucidated the role of near surface pH in the formation of the conversion coating.     

Fabrication and electrochemical properties of the Sn–Ni–P alloy rods array electrode for lithium-ion batteries

A new ternary Sn–Ni–P alloy rods array electrode for lithium-ion batteries is synthesized by electrodeposition with a Cu nanorods array structured foil as current collector. The Cu nanorods array foil is fabricated by heat treatment and electrochemical reduction of Cu(OH)₂ nanorods film, which is grown directly on Cu substrate through an oxidation method. The Sn–Ni–P alloy rods array electrode is mainly composed of pure Sn, Ni₃Sn₄ and Ni–P phases. The electrochemical experimental results illustrate that the Sn–Ni–P alloy rods array electrode has high reversible capacity and excellent coulombic efficiency, with an initial discharge capacity and charge capacity of 785.0 mAh g^?1 and 567.8 mAh g^?1, respectively. After the 100th discharge–charge cycling, capacity retention is 94.2% with a value of 534.8 mAh g^?1. The electrode also performs with an excellent rate capacity.     

Effects of electron beam irradiation on the photoelectrochemical properties of TiO2 film for DSSCs

TiO₂ has been widely utilized for various industrial applications such as photochemical cells, photocatalysts, and electrochromic devices. The crystallinity and morphology of TiO₂ films play a significant role in determining the overall efficiency of dye-sensitized solar cells (DSSCs). In this study, the preparation of nanostructured TiO₂ films by electron beam irradiation and their characterization were investigated for the application of DSSCs. TiO₂ films were exposed to 20–100 kGy of electron beam irradiation using 1.14 MeV energy acceleration with a 7.46 mA beam current and 10 kGy/pass dose rates. These samples were characterized using X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM), and X-ray photoelectron spectroscopy (XPS) analysis. After irradiation, each TiO₂ film was tested as a DSSC. At low doses of electron beam irradiation (20 kGy), the energy conversion efficiency of the film was approximately 4.0% under illumination of simulated sunlight with AM 1.5 G (100 mW/cm²). We found that electron beam irradiation resulted in surface modification of the TiO₂ films, which could explain the observed increase in the conversion efficiency in irradiated versus non-irradiated films.     

Polyaniline nanotubes for impedimetric triglyceride detection

Polyaniline nanotubes (PANI-NT) based film electrophoretically deposited onto indium–tin–oxide (ITO) coated glass plate has been utilized for covalent immobilization of lipase (LIP), via glutaraldehyde (Glu), for triglyceride detection using impedimetric technique. It is shown that fatty acid molecules produced during triglyceride hydrolysis result in change in charge transfer resistance (R_CT) of PANI-NT film with varying triglyceride concentration. LIP/Glu/PANI-NT/ITO bioelectrode has linearity as 25–300 mg dL^?1, sensitivity as 2.59 × 10^?3 KΩ^?1 mg^?1 dL, response time as 20 s and regression coefficient as 0.99. A low value of apparent Michaelis–Menten constant (～0.62 mM) indicates high enzyme affinity to tributyrin. The LIP/Glu/PANI-NT/ITO bioelectrode has been utilized to estimate triglyceride in serum samples.