A new sorbent for europium nitrate extraction: phosphonic acid grafted on polystyrene resin

A new chelating polymeric sorbent has been developed using polystyrene resin grafted with phosphonic acid. After characterization by FTIR and elementary analysis, the new resin has been investigated in liquid–solid extraction of europium(III). The results indicated that phosphonic resin could adsorb Eu(III) ion effectively from aqueous solution. The adsorption was strongly dependent on pH of the medium with enhanced adsorption as the pH value of 6.5. The influence of other analytical parameters including contact time, amount of resin, metal ion concentration, and ionic strength were investigated. The maximum uptake capacity of Eu(III) ions was 122.6 mg/g grafted resin at ambient temperature, at an initial pH value of 6.50. The overall adsorption process was best described by pseudo first-order kinetic. When Freundlich and Langmuir isotherms were tested, the latter had a better fit with the experimental data. Furthermore, Eu(III) could be eluted by using 1.0 mol/L H₂SO₄ solution and the grafted resin could be regenerated and reused.     

A new sorbent for uranium extraction: Polyethyleniminephenylphosphonamidic acid

A new sorbent, polyethyleniminemethylenephosphonamidic acid (PEIPPA), was synthesized from commercially available polyethylenimine and P,P-dichlorophenylphosphine oxide. After characterization by (¹H, ¹³C, ³¹P) NMR and FTIR, the new ion-exchange polymer has been investigated in liquid-solid extraction of uranium. The extraction strongly depends on the pH, initial concentration of uranium, extractant to analyte ratio (mol/mol), ionic strength of the liquid medium and their mutual interactions. Such interactions were investigated through factorial 3³ experimental designs in order to achieve the best conditions of batch sorption procedure, obtaining the mutual interaction among variables and optimizing these variables. The recovery of U(VI) is almost quantitative.     

Sorption efficiency of a new sorbent towards uranyl: phosphonic acid grafted Merrifield resin

A novel sorbent resin consisting of a Phosphonic Acid grafted on Merrifield Resin (PA-MR) for the extraction of uranyl from nitrate media is described. The sorption behaviour of uranyl cation on PA-MR was investigated using batch equilibrium technique. The effects of parameters such as shaking speed, pH levels, contact time, metal concentrations, ionic strength and temperature were reported. The results show that the sorption capacity increases with increasing both initial uranyl ion concentration and temperature and decreases with increasing ionic strength. Therefore, the optimum condition for the present study should be using 6.6 mg adsorbent per 1.0 mg uranyl in solution with pH 3.6 and shaking at 250 rpm for 180 min. The adsorption behavior of the system was also investigated and found to be in line with Langmuir isotherm. The kinetic data was well described by the pseudo second-order. Thermodynamics data leads to endothermic process ∆H = + 31.03 kJ⁻¹ mol⁻¹, ∆S = + 146.64 J mol⁻¹ K⁻¹ and ∆G = −11.96 kJ mol⁻¹ at 20 K. ∆G decreased to negatives values with increasing temperature indicating that the process was more favoured at high temperature.     

A new diamantane functionalized tris(aryloxide) ligand system for small molecule activation chemistry at reactive uranium complexes

The diamantane functionalized triazacyclononane ligand (^DiaArOH)₃tacn (L₃) has been synthesized and the reactivity of its U(III) metallated product [((^DiaArO)₃tacn)U] (1) has been explored. Complex 1 promotes dichloromethane and azidotrimethylsilane activation to generate U(IV) complex [((^DiaArO)₃tacn)U(Cl)] (2) and U(V) complex [((^DiaArO)₃tacn)U(NTMS)] (3), respectively. Spectroscopic investigations of complexes 1, 2, and 3 will be discussed, along with molecular structures where possible.     

Solid-phase extraction of lead(II) ions using multiwalled carbon nanotubes grafted with tris(2-aminoethyl)amine

Multiwalled carbon nanotubes were grafted with tris(2-aminoethyl)amine (MWCNTs-TAA) and employed for solid phase extraction and preconcentration of trace lead ions prior to its determination by inductively coupled plasma optical emission spectrometry. The material was characterized by FT-IR and Raman spectroscopy, thermosgravimetric and elemental analysis. The effects of pH value, shaking time, sample volume, elution conditions and potentially interfering ions were investigated. Under the optimum conditions, the maximum adsorption capacity is 38?mg?g^?1 of Pb(II), the detection limit is 0.32?ng?mL^?1, the enrichment factor is 60, and the relative standard deviation is 3.5% (n?=?6). The method has been applied to the preconcentration of trace amounts of Pb(II) in environmental water samples with satisfactory results.

Batch and dynamic extraction of uranium(VI) from nitric acid medium by commercial phosphinic acid resin,Tulsion CH-96

Batch and dynamic extractions of uranium(VI) in 10⁻³–10⁻²M concentrations in 3–4M nitric acid medium have been investigated using a commercially available phosphinic acid resin (Tulsion CH-96). The extraction of uranium(VI) has been studied as a function of time, batch factor (V/m), concentrations of nitric acid and uranium(VI) ion. Dual extraction mechanism unique to phosphinic acid resin has been established for the extraction of uranium(VI). Distribution coefficient (K _d ) of uranium(VI) initially decreases with increasing concentration of nitric acid, reaches a minimum value at 1.3M, followed by increases in K _d . A maximum K _d value of ∼2000 ml/g was obtained at 5.0M nitric acid. Batch extraction data has been fitted into the linearized Langmuir adsorption isotherm. The performance of the resin under dynamic extraction conditions was assessed by following the breakthrough behavior of the system. Effect of flow rate, concentrations of nitric acid and uranium ion in the feed on the breakthrough behavior of the system was studied and the data was fitted using Thomas model.     

A column system for the selective extraction of U(VI) and Th(IV) using a new chelating sorbent

A new method has been developed using (bis-3,4-dihydroxy benzyl)p-phenylene diamine functionalized to XAD-16 (a polystyrene divinyl benzene copolymer) matrix, to preconcentrate mainly U(VI) and Th(IV) from synthetic and real samples. The developed method is free from matrix interference due to alkali and alkaline metal ions and preconcentrates the actinides with a high degree of selectivity, with consistent trace recoveries. The new chelating resin provides dramatic improvement in metal exchange rate, with half value saturation time (t_1/2) of less than 1.6 min. The developed method was superior in its metal loading capacity for U(VI) and Th(IV), with values of 0.666 and 0.664 mmol g⁻¹, respectively. Various physio-chemical properties like effect of solution pH, kinetic studies, resin loading capacity, sample breakthrough volume, matrix effects etc., on metal ion sorption to sorbent phase, were studied using both batch and column method. The new chelatogen was applied to extract U(VI) from near neutral real water samples. Preconcentration and separation of metal ions were possible through pH variation and also by varying the eluant concentration. A high preconcentration factor value of 350 with a lower limit of detection of 20 and 30 ng cm⁻³ was obtained for U(VI) and Th(IV), respectively. The practical applicability of the developed resin was examined using synthetic and real samples such as sea/well water samples. The method provides low relative standard deviation values of <3.5% for all analytical measurements, reflecting on the reproducibility and accuracy of the developed method. The new resin is quite durable with recycling time >35 cycles, without any major change in its quantitative metal uptake nature.     

A new chelating sorbent for metal ion extraction under high saline conditions

A new chelating polymeric sorbent was developed by functionalizing Amberlite XAD-16 with 1,3-dimethyl-3-aminopropan-1-ol via a simple condensation mechanism. The newly developed chelating matrix offered a high resin capacity and faster sorption kinetics for the metal ions such as Mn(II), Pb(II), Ni(II), Co(II), Cu(II), Cd(II) and Zn(II). Various physio-chemical parameters like pH-effect, kinetics, eluant volume and flow rate, sample breakthrough volume, matrix interference effect on the metal ion sorption have been studied. The optimum pH range for the sorption of the above mentioned metal ions were 6.0–7.5, 6.0–7.0, 8.0–8.5, 7.0–7.5, 6.5–7.5, 7.5–8.5 and 6.5–7.0, respectively. The resin capacities for Mn(II), Pb(II), Ni(II), Co(II), Cu(II), Cd(II) and Zn(II) were found to be 0.62, 0.23, 0.55, 0.27, 0.46, 0.21 and 0.25 mmol g⁻¹ of the resin, respectively. The lower limit of detection was 10 ng ml⁻¹ for Cd(II), 40 ng ml⁻¹ for Mn(II) and Zn(II), 32 ng ml⁻¹ for Ni(II), 25 ng ml⁻¹ for Cu(II) and Co(II) and 20 ng ml⁻¹ for Pb(II). A high preconcentration value of 300 in the case of Mn(II), Co(II), Ni(II), Cu(II),Cd(II) and a value of 500 and 250 for Pb(II) and Zn(II), respectively, were achieved. A recovery of >98% was obtained for all the metal ions with 4 M HCl as eluting agent except in the case of Cu(II) where in 6 M HCl was necessary. The chelating polymer showed low sorption behavior to alkali and alkaline earth metals and also to various inorganic anionic species present in saline matrix. The method was applied for metal ion determination from water samples like seawater, well water and tap water and also from green leafy vegetable, from certified multivitamin tablets and steel samples.     

A novel extractant-impregnated resin containing carminic acid for selective separation and pre-concentration of uranium(VI) and thorium(IV)

The present work proposes the use of a novel extractant-impregnated resin (EIR) as an adsorbent in trace separation and pre-concentration of U(VI) and Th(IV) ions. The new EIR was prepared by impregnating carminic acid onto Amberlite XAD-16 resin beads. The morphology of new EIR was studied by BET surface area measurements and SEM micrographs. A column packed with CA/XAD-16 was used for selective separation and pre-concentration of the metal ions. Maximum adsorption of Th(IV) and U(VI) ions occurred at pHs of 3.50–5.75 and 3.75–6.50, respectively. The adsorbed metals could be eluted sequentially using 0.55?mol?L^?1 HCl for U(VI) and 2.25?mol?L^?1 HCl for Th(IV). The dynamic capacity of EIR was found to be 0.832 and 0.814?mmol?g^?1 for Th(IV) and U(VI), respectively. The tolerance limit of some foreign ions was also studied. The proposed method showed a good performance in analyzing geological reference materials and a synthetic seawater sample. Furthermore, the above procedure was successfully employed for the analysis of natural water samples.     

Efficient procedure for the preparation of (vinyl)polystyrene resin

(Vinyl)polystyrene resin is prepared in one step by treatment of Merrifield resin with an excess dimethylsulfonium methylide.     

混合模式吸附剂固相萃取-气相色谱-质谱法测定皮革中的磷酸三（2-氯乙基）酯

磷酸三（2-氯乙基）酯（TCEP）是一种皮革生产中常用的加工助剂,其具有致癌、神经毒性和生殖毒性,被欧洲化学品管理局列入禁用的第二批授权物质清单。由于皮革产品基质复杂,采用常用的固相萃取（SPE）方法提取对TCEP的回收率不高。Silica-WCX是一种自制的含有羧基与烷基的新型混合模式吸附剂。研究表明,通过在酸性条件下使其羧基保持质子化状态,能有效增强Silica-WCX对极性化合物TCEP的萃取性能,使TCEP的回收率得到明显提高。本文以Silica-WCX为SPE材料,建立了测定皮革中TCEP的SPE-GC-MS方法。该方法的线性范围为0.10~100.0 μg/L,定量限（S/N=10）为44.46 ng/kg,不同添加水平下TCEP的平均回收率在91.45%~99.98%之间,相对标准偏差（RSD）在4.33%~5.97%之间。该方法简便快捷,灵敏度高,定量限低于欧盟《化学品的注册、评估、授权和限制》（registration,evaluation,authorization and restriction of chemicals,REACH）法规的限量要求,适用于皮革及其制品中TCEP的测定。     

Enrichment of Pb(II) ions using phthalic acid functionalized XAD-16 resin as a sorbent

A simple and reliable method has been developed using polymeric material containing phthalic acid as a chelating agent to concentrate ultratrace amounts of lead ions in aqueous solutions. After characterization by CHN, IR, and thermal studies, the static and dynamic sorption behavior of Pb(II) ions onto new synthetic resin has been investigated. The sorption has been optimized with respect to pH, shaking speed, and contact time between the two phases. Maximum sorption is achieved from solution of pH 5-8 after 10 min agitation time. The lowest concentration for quantitative recovery is 5.8 ng cm(-3) with a preconcentration factor of approximately 850. The kinetics of sorption follows the first-order rate equation with the rate constant k=0.58+/-0.04 min(-1). The variation of the equilibrium constant K(c) with temperature between 10 and 50 degrees C yields values of DeltaH, 52.4+/-1.65 kJmol(-1), DeltaS, 186+/-5.21 Jmol(-1)K(-1), and DeltaG(303K), -4.15+/-0.002 kJmol(-1). The sorption data of Pb(II) ions in the concentration range from 2.41x10(-6) to 1.44x10(-4) molL(-1) follows the Langmuir, Freundlich, and Dubinin-Radushkevich (D-R) isotherms at all temperatures investigated. The sorption of Pb(II) ions onto synthesized resin in the presence of common anions and cations has also been measured. The possible sorption mechanism of Pb(II) ions onto phthalic acid modified XAD-16 is also discussed. The sorption procedure is utilized to preconcentrate Pb(II) ions prior to their determination in automobile exhaust particulates by atomic absorption spectrometry using direct and standard addition methods.     

A new tris(ferrocenylamine) ditertiary phosphine: Synthesis and co-ordination studies

The new tris(ferrocenylamine) ditertiary phosphine 1,1′-{FcCH₂N(CH₂PPh₂)CH₂(η⁵-C₅H₄)}₂Fe [Fc = (η⁵-C₅H₅)Fe(η⁵-C₅H₄)] has been prepared along with two coordination complexes. All compounds have been characterised by a combination of spectroscopic and analytical methods. The single crystal X-ray structure of the pentametallic Ru₂Fe₃ complex 5 has been determined.     

Ultrathin poly(N-isopropylacrylamide) grafted layer on polystyrene surfaces for cell adhesion/detachment control

We investigated physicochemical properties of two types of poly(N-isopropylacrylamide) (PIPAAm)-grafted tissue culture polystyrene (TCPS) surfaces, to elucidate the influential factors for thermally regulated cell adhesion and detachment to PIPAAm-grafted surfaces. The two types of PIPAAm-grafted surfaces were prepared by the electron beam polymerization method. Attenuated total reflection Fourier transform infrared spectroscopy revealed that amounts of the grafted polymers were 1.4 +/- 0.1 microg/cm2 for PIPAAm-1.4 and 2.9 +/- 0.1 microg/cm2 for PIPAAm-2.9. Both PIPAAm-grafted surfaces showed hydrophobic/hydrophilic property alterations in response to temperature. However, PIPAAm-1.4 surfaces were more hydrophobic (cos theta = 0.21 at 37 degrees C and cos theta = 0.35 at 20 degrees C) than PIPAAm-2.9 (cos theta = 0.42 at 37 degrees C and cos theta = 0.50 at 20 degrees C) both above and below the PIPAAm's transition temperature. Thicknesses of the grafted PIPAAm layers were estimated to be 15.5 +/- 7.2 nm for PIPAAm-1.4 and 29.5 +/- 8.4 nm for PIPAAm-2.9, by the use of UV excimer laser and atomic force microscope. Bovine carotid artery endothelial cells (ECs) adhere to the surfaces of PIPAAm-1.4 and proliferate to form confluent cell monolayers. The cell monolayers were harvested as single cell sheets by temperature decrease from 37 to 20 degrees C. On the contrary, ECs did not adhere to the surfaces of PIPAAm-2.9. This phenomenon was correlated with an adsorption of cell adhesion protein, fibronectin, onto surfaces ofPIPAAm-1.4 and -2.9. In the case of nano-ordered thin grafted surfaces, the surface chain mobility is strongly influenced by the thickness of PIPAAm grafted layers because dehydration of PIPAAm chains should be enhanced by the hydrophobic TCPS surfaces. PIPAAm graft amounts, that is, thickness of the PIPAAm grafted layers, play a crucial role in temperature-induced hydrophilic/hydrophobic property alterations and cell adhesion/detachment behavior.     

Polyaniline-coated Fe(3) O(4) nanoparticles: An anion exchange magnetic sorbent for solid-phase extraction

In this study, the capability of the prepared polyaniline-coated Fe(3) O(4) nanoparticles for magnetic solid-phase extraction of three parabens from environmental wastewater, cream, and toothpaste samples is presented. Synthesized Fe(3) O(4) nanoparticles were coated with sulfate-doped polyaniline via polymerization of aniline in the presence of Fe(3) O(4) nanoparticles and sulfuric acid. Here, polyaniline-coated Fe(3) O(4) nanoparticles are presented as anion exchange sorbent, which extract anionic form of parabens via anion exchange with dopant of polyaniline. The experimental conditions affecting extraction efficiency were further studied and optimized. The experimental results showed that maximum extraction efficiency can be obtained at 70 mL sample solution of pH 8, extraction and desorption times of 2 and 1 min, respectively, 100 μL of 3% (v/v) acetic acid in acetonitrile as eluent, and 100 mg of the adsorbent. Under these conditions, the linear dynamic ranges were 0.5-100 μg/L with good correlation coefficients (0.998-0.999). The detection limits were in the range of 0.3-0.4 μg/L and the relative standard deviations were less than 2.4 (n = 5) for the three parabens. Finally, this fast and efficient method was further employed for determination of target analytes in cream, toothpaste, and environmental wastewater samples and satisfactory results were obtained.     

A hyperbranched polyamidoamine dendrimer grafted onto magnetized graphene oxide as a sorbent for the extraction of synthetic dyes from foodstuff

Microchimica Acta - Graphene oxide nanosheets were modified with magnetite nanoparticles, and a hyperbranched polyamidoamine dendrimer was then covalently attached to their surface. The resulting...