Self-nucleation and enhanced nucleation of polymers. Definition of a convenient calorimetric “efficiency scale” and evaluation of nucleating additives in isotactic polypropylene (α phase)

A simple, convenient and reliable calorimetric efficiency scale is proposed for the evaluation of nucleating additives for polymers. The scale is based on conventional differential scanning calorimetry cooling runs and makes use of a crystallization range determined in self-nucleation experiments. It can be correlated with spherulite sizes, and indicates the potential range of improvement of nucleating additives. Typical nucleating agents for isotactic polypropylene are evaluated; at best they rate at 60 to ca. 70% on this efficiency scale. © 1993 John Wiley & Sons, Inc.     

Transformation of isotactic polypropylene droplets from the mesophase into the α‐phase

The structural transformation of homogeneously nucleated metastable mesophase of polypropylene (PP) particles was investigated in this study. We demonstrated the formation of heterogeneity‐free mesophase by slow cooling of the droplets unlike mesophase formation by quenching of the PP melt, which contained large number of bulk nuclei. Submicron size PP droplets were produced by thermal break up of PP and polystyrene layered film assembly. When cooled from melt, the PP droplets crystallized into mesophase at 44 °C revealing granular morphology. Subsequent heating thermogram of the PP particles showed a broad exotherm, which was attributed to the transformation of mesophase into α‐phase. This transformation was investigated during heating by annealing the PP particles at different temperatures. Annealed PP particles were analyzed by means of thermal, morphological and structural properties measurements. Results revealed a two step process for the transformation process. In the first step, the internal rearrangement of PP chains, as against melting and recrystallization of the mesophase, was observed. Since granular morphology was not affected significantly up to 120 °C, it was suggested that translational and rotational motions of PP helices produced ordered α‐phase. In the second step, increment in grain size distribution was observed, when the droplets were annealed at 140 °C. The results were attributed to enhanced chain mobility and merging of the grain boundaries. Annealing at 160 °C revealed the formation of short lamellar structures. Crystal thickening, melting and recrystallization of α‐phase were suggested at high temperature annealing. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Molecular deformation mechanisms of isotactic polypropylene in α‐ and β‐crystal forms by FTIR spectroscopy

The orientation behavior of isotactic polypropylene (iPP) in α‐ and β‐crystal form was investigated by rheo‐optical Fourier transformed infrared (FTIR) spectroscopy. This method enabled quantification of the degree of orientation as a feature of structural changes during uniaxial elongation in not only the crystalline phase but also the amorphous one. Molecular orientation mechanisms can be successfully derived from experimental results. Generally, three mechanisms were detected for iPP: (1) interlamellar separation in the amorphous phase, (2) interlamellar slip and lamellar twisting at small elongations, and (3) intralamellar slip at high elongations. The third mechanism was favored by α‐PP, whereas β‐PP favored the second mechanism, which, in fact, was responsible for the different mechanical properties of both materials at the macroscopic level. On the other hand, crystallization conditions may have significantly affected the amorphous orientation. Nevertheless, for both iPP types the chains in the amorphous phase always oriented less than did those in the crystalline phase. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4478–4488, 2004     

Crystallization and melting of isotactic polypropylene in response to temperature modulation

Isotactic polypropylene (iPP) was crystallized using temperature modulation in a differential scanning calorimeter (DSC) to thicken the crystals formed on cooling from the melt. A cool-heat modulation method was adopted for the preparation of the samples under a series of conditions. The effect of modulation parameters, such as temperature amplitude and period was monitored with the heating rate that followed. Thickening of the lamellae as a result of the crystallization treatment enabled by the cool-heat method lead to an increase in the peak melting temperature and the final traces of melting. For instance, iPP melting peak shifted by up to 3.5°C with temperature amplitude of 1.0°C while the crystallinity was increased from 0.45 (linearly cooled) to 0.53. Multiple melting endotherms were also observed in some cases, but this was sensitive to the temperature changes experienced on cooling. Even with a slower underlying cooling rate and small temperature amplitudes, some recrystallization and reorganization occurred during the subsequent heating scan. The crystallinity was increased significantly and this was attributed to the crystal perfection that occurred at the crystal growth surface. In addition, temperature modulated differential scanning calorimetry (TMDSC) has been used to study the melting of iPP for various crystallization treatments. The reversing and non-reversing contribution under the experimental time scale was modified by the relative crystal stability formed during crystallization. Much of the melting of iPP was found to be irreversible.This revised version was published online in November 2005 with corrections to the Cover Date.     

Crystallization and phase morphology of injection‐molded isotactic polypropylene (iPP)/syndiotactic polypropylene (sPP) blends

The crystallization and phase morphology of the injection‐molded isotactic polypropylene (iPP)/syndiotactic polypylenen (sPP) blends were studied, focusing on the difference between the skin layer and core layer. The distribution of crystallinity of PPs in the blends calculated based upon the DSC results shows an adverse situation when compared with that in the neat polymer samples. For 50/50 wt % iPP/sPP blend, the SEM results indicated that a dispersed structure in the skin layer and a cocontinuous structure in the core layer were observed. A migration phenomenon that the sPP component with lower crystallization temperature and viscosity move to the core layer, whereas the iPP component with higher crystallization temperature and viscosity move to the skin layer, occurred in the iPP/sPP blend during injection molding process. The phenomenon of low viscosity content migrate to the low shear zone may be due to the crystallization‐induced demixing based upon the significant difference of crystallization temperature in the sPP and iPP. This migration caused the composition inhomogeneity in the blend and influenced the accuracy of crystallinity calculated based upon the initial composition. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2948–2955, 2007     

Step‐like melting mechanisms of isothermally crystallized isotactic polypropylene

The complex melting behavior of isotactic polypropylene, after isothermal crystallization, was studied within the context of step‐like melting mechanisms which were previously proposed for high temperature polymers. The morphological characteristics of the melting process were also studied as a function of molecular weight, and close similarities were observed with respect to high temperature polymers. Positive birefringence crystals of low molecular weight samples developed double melting behavior in three steps. The first melting step was assigned to continuous melting of secondary crosshatch reversing lamellae, together with recrystallization of the remaining isothermal crystals. In the second melting step (first melting endotherm), crystals tended to lose their original coarse negative birefringence due to melting of secondary reversing branching. This effect rendered new, finer texture, but still negative birefringence crystals. In the third melting step (second melting endotherm), there was a combination of melting of two crystal populations, one consisting of the remaining fraction of reversing primary crystals, and the other consisting of nonreversing primary crystals. A crosshatch secondary branching model was therefore proposed to explain the overall results. Mixed birefringence spherulites of high molecular weight samples displayed similar, although proportional, behavior under identical crystallization and melting conditions corroborating the proposed melting mechanism. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2188–2200, 2008     

Isothermal crystallization behaviors of isotactic polypropylene nucleated with α/β compounding nucleating agents

Sodium 2,2′‐methylene‐bis(4,6‐di‐tert‐butylphenyl) phosphate (NA40) and N,N‐dicyclohexylterephthalamide (NABW) are high effective nucleating agents for inducing the formation of α‐isotactic polypropylene (α‐iPP) and β‐iPP, respectively. The isothermal crystallization kinetics of iPP nucleated with nucleating agents NABW, NA40/NABW (weight ratio of NA40 to NABW is 1:1) and NA40 were investigated by differential scanning calorimetry (DSC) and Avrami equation was adopted to analyze the experimental data. The results show that the addition of NABW, NA40/NABW and NA40 can shorten crystallization half‐time (t_1/2) and increase crystallization rate of iPP greatly. In these three nucleating agents, the α nucleating agent NA40 can shorten t_1/2 of iPP by the largest extent, which indicates that it has the best nucleation effect. While iPP nucleated with NA40/NABW compounding nucleating agents has shorter t_1/2 than iPP nucleated with NABW. The Avrami exponents of iPP and nucleated iPP are close to 3.0, which indicates that the addition of nucleating agents doesn't change the crystallization growth patterns of iPP under isothermal conditions and the crystal growth is heterogeneous three‐dimensional spherulitic growth. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 590–596, 2007     

Molecular weight dependency of crystallization and melting behavior of β‐nucleated isotactic polypropylene

Compounds of isotactic polypropylene (iPP) and β‐nucleating agent were used to investigate the relationship between the development of β phase and molecular weight in iPP under quiescent crystallization conditions by using wide angle X‐ray diffraction and differential scanning calorimetry techniques. In all cases, the dependency of the formation of β phase in iPP on molecular weight of iPP at a defined crystallization temperature range was found. The iPP with high molecular weight possessed a wide range of crystallization temperature in inducing rich β phase. However, poor or even no β phase was obtained for the samples with low molecular weight in the same range. In addition, an upper critical crystallization temperature of producing dominant β phase was found at 125 °C. Beyond this temperature, a phenomenon of prevailing α phase became obvious. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 1301–1308     

Crystallization and melting behaviors of isotactic polypropylene nucleated with compound nucleating agents

Crystallization and melting behaviors of isotactic polypropylene (iPP) nucleated with compound nucleating agents of sodium 2,2′‐methylene‐bis (4,6‐di‐tert‐butylphenyl) phosphate (hereinafter called as NA40)/dicyclohexylterephthalamide (hereinafter called as NABW) (weight ratio of NA40 to NABW is 1:1) were studied by differential scanning calorimetry and wide‐angle X‐ray diffraction (WAXD), the relative β‐amount of iPP nucleated with these compound nucleating agents was also calculated in Turner‐Jones equation by using wide‐angle X‐ray diffraction data. Under isothermal crystallization, there exists a temperature range favorable for formation of β‐iPP. When the concentration of compound nucleating agents is 0.2 wt %, the temperature range is from 100 to 140 °C. While in nonisothermal crystallization, lower cooling rate is favorable for form of β‐iPP and the relative β‐amount of iPP increases with the decreasing of cooling rate in crystallization process. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 911–916, 2008     

The influences of α/β compound nucleating agents based on octamethylenedicarboxylic dibenzoylhydrazide on crystallization and melting behavior of isotactic polypropylene

The influences of α/β compound nucleating agents based on octamethylenedicarboxylic dibenzoylhydrazide on crystallization and melting behavior of isotactic polypropylene (iPP) were analyzed. It is found that the crystallization temperatures of nucleated iPP were increased by above 11.0°C and the relative contents of β‐crystals (K_β ) in iPP reached above 0.40 after addition of compound nucleating agents. The K_β values depend on cooling rate, crystallization temperature in isothermal crystallization, and the difference between the crystallization temperatures of iPP nucleated by two individual nucleating agents. The nonisothermal crystallization kinetics were studied by Caze method and Mo method, respectively. The effective activation energy was calculated by the Friedman's method. The results illustrate that the half crystallization time was shortened and the crystallization rate was increased obviously after addition of nucleating agents, and the effective activation energy was increased with the relative crystallinity.     

Nucleation of isotactic polypropylene crystallization by gold nanoparticles

Nucleation of isotactic polypropylene (iPP) crystallization by gold (Au) nanoparticles was studied. Regardless of their size, 4.3, 8.8, 28.3, and 84.5 nm, all particles were able to nucleate spherulites when deposited on the iPP surface. However, when added and melt‐mixed with iPP, only the smallest particles affected significantly the iPP bulk crystallization. Au nanoparticles larger than 4.3 nm, at the concentration of 0.001 wt %, did not influence the crystallization of iPP. Contrary to this, 0.001 and 0.005 wt % of Au nanoparticles having the size of 4.3 nm increased crystallization temperature of the iPP by 7–8 °C and decreased markedly the sizes of polycrystalline aggregates. Aggregation of Au nanoparticles in the polymer matrix was evidenced by electron microscopy and contributed to their decreased effectiveness in the nucleation of iPP crystallization. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 469–478, 2010     

The β‐crystalline form of isotactic polypropylene in blends of isotactic polypropylene and polyamide‐6/clay nanocomposites

Blends of isotactic polypropylene and polyamide‐6/clay nanocomposites (iPP/NPA6) were prepared with an internal batch mixer. A high content of the β‐crystalline form of isotactic polypropylene (β‐iPP) was observed in the injection‐molded samples of the iPP/NPA6 blends, whereas the content of β‐iPP in the iPP/PA6 blends and the iPP/clay composite was low and similar to that of neat iPP. Quiescent melt crystallization was studied by means of wide‐angle X‐ray diffraction, differential scanning calorimetry, and polarized optical microscopy. We found that the significant β‐iPP is not formed during quiescent melt crystallization regardless of whether the sample used was the iPP/NPA6 blend or an NPA6 fiber/iPP composite. Further characterization of the injection‐molded iPP/NPA6 revealed a shear‐induced skin–core distribution of β‐iPP and the formation of β‐iPP in the iPP/NPA6 blends is related to the shear flow field during cavity‐filling. In the presence of clay, the deformation ability of the NPA6 domain is decreased, as evidenced by rheological and morphological studies. It is reasonable that the enhanced relative shear, caused by low deformability of the NPA6 domain in the iPP matrix, is responsible for β‐iPP formation in the iPP/NPA6 blends. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3428–3438, 2004     

Partial melting and recrystallization of isotactic polypropylene

<正>A relatively high predetermined crystallization temperature(135℃) was chosen to grow well developed iPP spherulites,then the partial melting was carried out at a temperature of 165℃,where the preformed spherulites were seen to only decrease their size but not completely melted.The crystallization behavior of partially melted isotactic polypropylene (iPP) has been carefully examined by different scanning calorimetry(DSC) and polarized light microscopy(PLM).The experimental results show that at a special annealing temperature(165℃) the melting behavior of iPP includes two parts with different mechanism,one part is the melting of iPP spherulite outside,another is the partial lamellae perfection during longer annealing time in the unmelted spherulite.The conformational orders of the iPP melt decrease with the increase of the annealing temperature.     

Fractionated crystallization of α‐ and β‐nucleated polypropylene droplets

A layer multiplying coextrusion process was used to produce multilayered polypropylene/polystyrene (PP/PS) films with various nucleating agents. When heated into the melt, the thin PP layers broke up into submicron PP droplets that exhibited fractionated crystallization. If the initial PP layers were 20 nm or less, the resulting droplets exhibited exclusively homogeneous nucleation. If a nucleating agent was added, the systematic departure from homogeneous nucleation provided insight into the nature of the heterogeneous nucleation. In this study, we used thermal analysis, atomic force microscopy (AFM), and wide angle X‐Ray scattering (WAXS) to examine the effect of two nucleating agents. We confirmed with WAXS and AFM that a soluble sorbitol nucleating agent for the PP α‐form operates in three concentration regimes as proposed in a previous study. Morphologically, homogeneous nucleation of the submicron droplets produced a granular texture. The correlation length from small‐angle X‐Ray scattering (SAXS) suggested that the grains contained 1–3 mesophase domains. Drawing on classical nucleation theory, the critical size nucleus of an individual mesophase domain was estimated to be about 2 nm³, which was considerably smaller than the mesophase domain. This pointed to mesophase crystallization that included the processes of nucleation and growth. Additional experiments were performed with nucleating agents for the PP β‐form. However, they were not effective in nucleating crystallization of the droplets, presumably because they were essentially insoluble in PP and the nucleating particles were too large to be accommodated in the PP droplets. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Features of the hedritic morphology of β‐isotactic polypropylene studied by atomic force microscopy

The lamellar organization of melt‐crystallized β‐isotactic polypropylene was studied by atomic force microscopy (AFM) after permanganic etching. Hedritic objects grown at a high crystallization temperature (140–143 °C) were investigated. Essential features of the hedritic development were revealed by the characteristic projections exposed at the sample surface. A three‐dimensional view of the morphology was obtained by AFM. Hedritic growth proceeded mainly by branching around screw dislocations resulting in new lamellae that further developed. Successive lamellar layers often diverged. Deviation from the planar lamellar habit was observed, varying with the position within the hedrite. Twisting of the lamellae also was observed occasionally in the vicinity of the screw dislocations. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 672–681, 2000     

Crystallinity changes in plastically deformed isotactic polypropylene evaluated by x‐ray diffraction and differential scanning calorimetry methods

The crystallinity of isotactic polypropylene (iPP), when deformed with plastic plane‐strain compression, was studied with wide‐angle X‐ray scattering (WAXS) and differential scanning calorimetry (DSC) techniques. A comparison of the obtained crystallinity data with annealed iPP samples was performed. The material used in this study was commercial iPP (weight‐average molecular weight = 117.400 g/mol; number‐average molecular weight = 17.300 g/mol). A significant decrease in the crystallinity was observed with increasing deformation pressure when the X‐ray method was employed, whereas only a small decrease was registered when the DSC method of crystallinity determination was used. However, the annealed iPP samples demonstrated a slight crystallinity increase when evaluated by both techniques. The reason for the difference between WAXS and DSC crystallinity results is discussed. This study of iPP specimens subjected to large deformation led us to the conclusion that the WAXS method provides accurate crystallinity values for the deformed material, whereas the values obtained by the DSC method do not reproduce the real crystallinity of the deformed material. This is due to the inherent heating process of the method, which causes a relaxation process and a significant change in the crystallinity of the deformed material, providing values nearer to its intrinsic equilibrium state. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 896–903, 2002     

Crystallization behavior and morphology of β‐nucleated isotactic polypropylene with different stereo‐defect distribution

Aiming at further investigating the combination effect of concentration of β‐nucleating agent (β‐NA) and stereo‐defect distribution on the crystallization behavior of β‐nucleated isotactic polypropylene (β‐iPP), in this study, the crystallization behavior and polymorphic morphology of twoβ‐iPP resins with nearly same average isotacticity (PP‐A and PP‐B) but different uniformities of stereo‐defect distribution were investigated by differential scanning calorimetry (DSC), wide angle X‐ray diffraction (WAXD) and polarized optical microscopy (POM). The results of DSC and WAXD showed that the addition of TMB‐5 increases the crystallization temperature and decreases the spherulite sizes of both PP‐A and PP‐B, and reduces their crystallization energy barriers as well; however, the polymorphic behaviors of PP‐A and PP‐B exhibit different dependence on the TMB‐5 concentration. For PP‐A with less uniform distribution of stereo‐defects, β‐phase can be observed only when the TMB‐5 concentration is no less than 0.1 wt.%, while for PP‐B with more uniform stereo‐defect distribution, addition of 0.01 wt.% TMB‐5 can induce the formation of β‐phase. Moreover, the analysis of POM indicated that the crystalline morphologies of both PP‐A and PP‐B change greatly with the TMB‐5 concentration, and the variation features of PP‐A and PP‐B are quite different from each other. PP‐B with more uniform stereo‐defect distribution was more favorable for the formation of large amount of β‐phase in the presence of wide concentration range of TMB‐5. The different polymorphic behaviors and their different dependences on the β‐NA concentration were related to the different uniformities of stereo‐defect distribution of the samples, since the distribution of stereo‐defects could restrain the regular insertion of molecular chains during crystallization and thus determine the tendency the α‐phase crystallization of the sample. Copyright © 2014 John Wiley & Sons, Ltd.     

Annealing induced microstructure and fracture resistance changes in isotactic polypropylene/ethylene‐octene copolymer blends with and without β‐phase nucleating agent

Previous work showed that annealing induced the great improvement of fracture resistance of β‐iPP, relating to the decreased number of chain segments in the amorphous region. To further prove the rationality of this observation, in this work, the ethylene‐octene copolymer (POE) toughened isotactic polypropylene (iPP) blends with or without β‐phase nucleating agent (β‐NA) were adopted and the changes of microstructure and fracture resistance during the annealing process were further investigated comparatively. The results showed that, whether for the α‐phase crystalline structure (non‐nucleated) or for the β‐phase crystalline structure (β‐NA nucleated) in iPP matrix, annealing can induce the dramatic improvement of fracture resistance at a certain annealing temperature (120–140 °C for β‐NA nucleated blends whereas 120–150 °C for non‐nucleated blends). Especially, non‐nucleated blends exhibit more apparent variations in fracture resistance compared with β‐NA nucleated blends during the annealing process. The phase morphology of elastomer, supermolecular structure of matrix, the crystalline structure including the degree of crystallinity and the relative content of β‐phase, and the relaxation of chain segments were investigated to explore the toughening mechanism of the samples after being annealed. It was proposed that, even if the content of elastomer is very few, the excellent fracture resistance can be easily achieved through adjusting the numbers of chain segments in the amorphous phase by annealing. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

The mechanism for fracture resistance in β‐nucleated isotactic polypropylene

The effects of molecular weight (MW) of isotactic polypropylene (iPP), the content of β‐PP, the size of its spherulites and the morphology of its α‐phase and β‐phase (α‐ and β‐PP) on the impact strength, with different contents of β‐nucleating agent, were investigated by two ways. The results show that the impact strength of iPPs increased initially, and then decreased with the content of β‐nucleating agent (maximum at 0.1 wt%). The impact strength was related to the size of β‐spherulites and had no apparent correlation with the content of β‐PP. The morphology of the bundle shape and intercrossing boundaries of β‐spherulites were dominant in improving impact strength with low content of β‐nucleating agent, while the MW of iPP was dominant with high content of β‐nucleating agent. Copyright © 2009 John Wiley & Sons, Ltd.