AlGaN/GaN槽栅HEMT模拟与实验研究

分析了栅槽深度对AlGaN/GaN HEMT特性的影响,并对不同栅槽深度的器件特性进行了模拟,得到了器件饱和电流、最大跨导和阈值电压随栅槽深度的变化规律.当槽栅深度增大,器件饱和电流逐渐下降,而最大跨导逐渐增大,阈值电压向X轴正方向移动.研制出不同栅槽深度的蓝宝石衬底AlGaN/GaN HEMT,用实验数据验证了得到的不同栅槽深度器件特性变化规律.从刻蚀损伤和刻蚀引入界面态的角度分析了模拟与实验规律产生差别的原因. 关键词： 高电子迁移率晶体管 AlGaN/GaN 槽栅器件     

AlGaN/GaN双异质结F注入增强型高电子迁移率晶体管

理论模拟了不同GaN沟道厚度的双异质结(AlGaN/GaN/AlGaN/GaN)材料对高电子迁移率晶体管(HEMT)特性的影响,并模拟了不同F注入剂量下用该材料制作的增强型器件的特性差异.采用双异质结材料,结合F注入工艺成功地研制出了较高正向阈值电压的增强型HEMT器件.实验研究了三种GaN沟道厚度制作的增强型器件直流特性的差异,与模拟结果进行了对比验证.采用降低的F注入等离子体功率,减小了等离子体处理工艺对器件沟道迁移率的损伤,研制出的器件未经高温退火即实现了较高的跨导和饱和电流特性.对14 nm GaN沟道厚度的器件进行了阈值电压温度稳定性和栅泄漏电流的比较研究,并且分析了双异质结器件的漏致势垒降低效应.     

具有高阈值电压和大栅压摆幅的常关型槽栅AlGaN/GaN金属氧化物半导体高电子迁移率晶体管

介绍了一种具有高阈值电压和大栅压摆幅的常关型槽栅AlGaN/GaN金属氧化物半导体高电子迁移率晶体管。采用原子层淀积(ALD)方法实现Al₂O₃栅介质的沉积。槽栅常关型AlGaN/GaN MOS-HEMT的栅长(L_g)为2 μm,栅宽(W_g)为0.9 mm(0.45 mm×2),栅极和源极(L_gs)之间的距离为5 μm,栅极和漏极(L_gd)之间的距离为10 μm。在栅压为－20 V时,槽栅常关型AlGaN/GaN MOS-HEMT的栅漏电仅为0.65 nA。在栅压为+12 V时,槽栅常关型AlGaN/GaN MOS-HEMT的栅漏电为225 nA。器件的栅压摆幅为－20~+12 V。在栅压V_gs=+10 V时,槽栅常关型AlGaN/GaN MOS-HEMT电流和饱和电流密度分别达到了98 mA和108 mA/mm (W_g=0.9 mm), 特征导通电阻为4 mΩ·cm²。槽栅常关型AlGaN/GaN MOS-HEMT的阈值电压为+4.6 V,开启与关断电流比达到了5×10⁸。当V_ds=7 V时,器件的峰值跨导为42 mS/mm (W_g=0.9 mm,V_gs=+10 V)。在V_gs=0 V时,栅漏间距为10 μm的槽栅常关型AlGaN/GaN MOS-HEMT的关断击穿电压为450 V,关断泄露电流为0.025 mA/mm。     

60Co γ射线辐射对AlGaN/GaN HEMT器件的影响

采用⁶⁰Co γ射线辐射源对非钝化保护的AlGaN/GaN高电子迁移率晶体管(HEMT)器件进行了1 Mrad(Si)的总剂量辐射,实验发现辐射累积剂量越大,器件尺寸越小,器件饱和漏电流和跨导下降越明显,同时辐射后器件栅泄漏电流明显增大,而阈值电压变化很小. 对辐射前后器件的沟道串联电阻和阈值电压变化的分析表明,辐射感生表面态负电荷的产生是造成AlGaN/GaN HEMT器件电特性退化的主要原因之一. 关键词： AlGaN/GaN HEMT器件 γ射线辐射 表面态     

具有高阈值电压和大栅压摆幅的常关型槽栅AlGaN/GaN金属氧化物半导体高电子迁移率晶体管（英文）

介绍了一种具有高阈值电压和大栅压摆幅的常关型槽栅AlGaN/GaN金属氧化物半导体高电子迁移率晶体管。采用原子层淀积(ALD)方法实现Al_2O_3栅介质的沉积。槽栅常关型AlGaN/GaN MOS-HEMT的栅长(Lg)为2μm,栅宽(Wg)为0.9 mm(0.45 mm×2),栅极和源极(Lgs)之间的距离为5μm,栅极和漏极(Lgd)之间的距离为10μm。在栅压为-20 V时,槽栅常关型AlGaN/GaN MOS-HEMT的栅漏电仅为0.65 nA。在栅压为+12 V时,槽栅常关型AlGaN/GaN MOS-HEMT的栅漏电为225 nA。器件的栅压摆幅为-20~+12V。在栅压V_(gs)=+10 V时,槽栅常关型AlGaN/GaN MOS-HEMT电流和饱和电流密度分别达到了98 mA和108 mA/mm(Wg=0.9 mm),特征导通电阻为4 mΩ·cm2。槽栅常关型AlGaN/GaN MOS-HEMT的阈值电压为+4.6 V,开启与关断电流比达到了5×108。当V_(ds)=7 V时,器件的峰值跨导为42 mS/mm(Wg=0.9 mm,V_(gs)=+10 V)。在V_(gs)=0 V时,栅漏间距为10μm的槽栅常关型AlGaN/GaN MOS-HEMT的关断击穿电压为450 V,关断泄露电流为0.025 mA/mm。     

3 MeV质子辐照对AlGaN/GaN高电子迁移率晶体管的影响

研究了AlGaN/GaN 高电子迁移率晶体管(HEMT)的质子辐照效应. 在3 MeV质子辐照下, 当辐照剂量达到1× 10¹⁵ protons/cm²时, 漏极饱和电流下降了20%, 最大跨导降低了5%. 随着剂量增加, 阈值电压向正向漂移, 栅泄露电流增加. 在相同辐照剂量下, 1.8 MeV质子辐照要比3 MeV质子辐照退化严重. 从SRIM软件仿真中得到不同能量质子在AlGaN/GaN异质结中的辐射损伤区, 以及在一定深度形成的空位密度. 结合变频C-V测试结果进行分析, 表明了质子辐照引入空位缺陷可能是AlGaN/GaN HEMT器件电学特性退化的主要原因.     

Al2O3绝缘层的AlGaN/GaN MOSHEMT器件研究

在研制AlGaN/GaN HEMT器件的基础上,采用ALD法制备了Al2O3 AlGaN/GaN MOSHEMT器件.通过X射线光电子能谱测试表明在AlGaN/GaN异质结材料上成功淀积了Al2O3薄膜.根据对HEMT和MOSHEMT器件肖特基电容、器件输出以及转移特性的测试进行分析发现:所制备的Al2O3,薄膜与AlGaN外延层间界面态密度较小,因而MOSHEMT器件呈现出较好的栅控性能;其次,该器件的栅压可以加至 3 V,此时的最大饱和电流达到800 mA/mm,远远高于肖特基栅HEMT器件的最大输出电流;而且栅漏反偏状态下的泄漏电流却减小了两个数量级,提高了器件的击穿电压,通过进一步分析认为泄漏电流主要来源于Fowler-Nordheim隧穿.     

60Co γ射线辐射对AlGaN/GaN HEMT器件的影响

采用60 Co γ射线辐射源对非钝化保护的AlGaN/GaN高电子迁移率晶体管(HEMT)器件进行了1 Mrad(Si)的总剂量辐射,实验发现辐射累积剂量越大,器件尺寸越小,器件饱和漏电流和跨导下降越明显,同时辐射后器件栅泄漏电流明显增大,而阈值电压变化很小. 对辐射前后器件的沟道串联电阻和阈值电压变化的分析表明,辐射感生表面态负电荷的产生是造成AlGaN/GaN HEMT器件电特性退化的主要原因之一.     

高场应力及栅应力下AlGaN/GaN HEMT器件退化研究

采用不同的高场应力和栅应力对AlGaN/GaN HEMT器件进行直流应力测试,实验发现：应力后器件主要参数如饱和漏电流,跨导峰值和阈值电压等均发生了明显退化,而且这些退化还是可以完全恢复的;高场应力下,器件特性的退化随高场应力偏置电压的增加和应力时间的累积而增大;对于不同的栅应力,相对来说,脉冲栅应力和开态栅应力下器件特性的退化比关态栅应力下的退化大.对不同应力前后器件饱和漏电流,跨导峰值和阈值电压的分析表明,AlGaN势垒层陷阱俘获沟道热电子以及栅极电子在栅漏间电场的作用下填充虚栅中的表面态是这些不同应 关键词： AlGaN/GaN HEMT器件 表面态(虚栅) 势垒层陷阱 应力     

具有高开启/关断电流比的Al2O3/AlGaN/GaN金属氧化物半导体高电子迁移率晶体管

采用原子层淀积(ALD)方法,制备了Al₂O₃为栅介质的高性能AlGaN/GaN金属氧化物半导体高电子迁移率晶体管(MOS-HEMT)。在栅压为-20 V时,MOS-HEMT的栅漏电比Schottky-gate HEMT的栅漏电低4个数量级以上。在栅压为+2 V时,Schottky-gate HEMT的栅漏电为191μA;在栅压为+20 V时,MOS-HEMT的栅漏电仅为23.6 nA,比同样尺寸的Schottky-gate HEMT的栅漏电低将近7个数量级。AlGaN/GaN MOS-HEMT的栅压摆幅达到了±20 V。在栅压V_gs=0 V时, MOS-HEMT的饱和电流密度达到了646 mA/mm,相比Schottky-gate HEMT的饱和电流密度(277 mA/mm)提高了133%。栅漏间距为10μm的AlGaN/GaN MOS-HEMT器件在栅压为+3 V时的最大饱和输出电流达到680 mA/mm,特征导通电阻为1.47 mΩ·cm²。Schottky-gate HEMT的开启与关断电流比仅为10⁵,MOS-HEMT的开启与关断电流比超过了10⁹,超出了Schottky-gate HEMT器件4个数量级,原因是栅漏电的降低提高了MOS-HEMT的开启与关断电流比。在V_gs=-14 V时,栅漏间距为10μm的AlGaN/GaN MOS-HEMT的关断击穿电压为640 V,关断泄露电流为27μA/mm。     

Enhancement-mode AlGaN/GaN high electronic mobility transistors with thin barrier

An enhancement-mode (E-mode) AlGaN/GaN high electron mobility transistor (HEMTs) was fabricated with 15-nm AlGaN barrier layer. E-mode operation was achieved by using fluorine plasma treatment and post-gate rapid thermal annealing. The thin barrier depletion-HEMTs with a threshold voltage typically around --1.7 V, which is higher than that of the 22-nm barrier depletion-mode HEMTs (--3.5 V). Therefore, the thin barrier is emerging as an excellent candidate to realize the enhancement-mode operation. With 0.6-μ m gate length, the devices treated by fluorine plasma for 150-W RF power at 150 s exhibited a threshold voltage of 1.3 V. The maximum drain current and maximum transconductance are 300 mA/mm, and 177 mS/mm, respectively. Compared with the 22-nm barrier E-mode devices, V_T of the thin barrier HEMTs is much more stable under the gate step-stress.     

AlGaN/GaN异质结Ni/Au肖特基表面处理及退火研究

采用O₂等离子体及HF溶液对AlGaN/GaN异质结材料进行表面处理后，Ni/Au肖特基接触特性比未处理有了明显改善，反向泄漏电流减小3个数量级.对制备的肖特基接触进行200—600℃ 5min的N₂气氛退火，发现退火冷却后肖特基反向泄漏电流随退火温度增大进一步减小.N₂气中600℃退火后肖特基二极管C-V特性曲线在不同频率下一致性变好，这表明退火中Ni向材料表面扩散减小了表面陷阱密度；C-V特性曲线随退火温度增大向右移动，从二维电子气耗尽电压绝对值减小反映了肖特基势垒的提高. 关键词： AlGaN/GaN 肖特基接触 表面处理 退火     

The effects of 60Co γ-ray irradiation on the DC characteristics of enhancement-mode AlGaN/GaN high-electron-mobility transistors

The effects of 60Co γ-ray irradiation on the DC characteristics of AlGaN/GaN enhancement-mode high-electron-mobility transistors (E-mode HEMTs) are investigated. The results show that having been irradiated by 60Co γ-rays at a dose of 3 Mrad (Si), the E-mode HEMT reduces its saturation drain current and maximal transconductance by 6% and 5%, respectively, and significantly increases both forward and reverse gate currents, while its threshold voltage is affected only slightly. The obvious performance degradation of E-mode AlGaN/GaN HEMTs is consistent with the creation of electronegative surface state charges in the source-gate spacer and gate-drain spacer after being irradiated.     

The effects of ⁶⁰Co γ-ray irradiation on the DC characteristics of enhancement-mode AlGaN/GaN high-electron-mobility transistors

The effects of 60Co γ-ray irradiation on the DC characteristics of AlGaN/GaN enhancement-mode high-electron-mobility transistors (E-mode HEMTs) are investigated. The results show that having been irradiated by 60Co γ-rays at a dose of 3 Mrad (Si), the E-mode HEMT reduces its saturation drain current and maximal transconductance by 6% and 5%, respectively, and significantly increases both forward and reverse gate currents, while its threshold voltage is affected only slightly. The obvious performance degradation of E-mode AlGaN/GaN HEMTs is consistent with the creation of electronegative surface state charges in the source-gate spacer and gate-drain spacer after being irradiated.     

High-electric-field-stress-induced degradation of SiN passivated AlGaN/GaN high electron mobility transistors

AlGaN/GaN high electron mobility transistors (HEMTs) are fabricated by employing SiN passivation, this paper investigates the degradation due to the high-electric-field stress. After the stress, a recoverable degradation has been found, consisting of the decrease of saturation drain current I_Dsat, maximal transconductance g_m, and the positive shift of threshold voltage V_TH at high drain-source voltage V_DS. The high-electric-field stress degrades the electric characteristics of AlGaN/GaN HEMTs because the high field increases the electron trapping at the surface and in AlGaN barrier layer. The SiN passivation of AlGaN/GaN HEMTs decreases the surface trapping and 2DEG depletion a little during the high-electric-field stress. After the hot carrier stress with V_DS=20 V and V_GS=0 V applied to the device for 10⁴ sec, the SiN passivation decreases the stress-induced degradation of I_Dsat from 36% to 30%. Both on-state and pulse-state stresses produce comparative decrease of I_Dsat, which shows that although the passivation is effective in suppressing electron trapping in surface states, it does not protect the device from high-electric-field degradation in nature. So passivation in conjunction with other technological solutions like cap layer, prepassivation surface treatments, or field-plate gate to weaken high-electric-field degradation should be adopted.     

Impact of oxygen in electrical properties and hot-carrier stress-induced degradation of GaN high electron mobility transistors

The role of the oxygen in AlGaN/GaN high electron mobility transistors (HEMTs) before and after semi-on state stress was discussed. Comparing with the electrical characteristics of the devices in vacuum, air, and oxygen atmosphere, it is revealed that the oxygen has significant influence on the electric characteristics and the hot-carrier-stress-induced degradation of the device. Comparing with the situation in vacuum, the gate leakage increased an order of magnitude in oxygen and air atmosphere. Double gate structure was used to separate the barrier leakage and surface leakage of AlGaN/GaN HEMT it is found that surface leakage is the major influencing factor in gate leakage of SiN-passivated devices before and after semi-on state stress. During semi-on state stress in the oxygen atmosphere, the electric-field-driven oxidation process promoted the oxidation of the nitride layer, and the oxidation layer in the SiN/AlGaN interface leads to the decreasing of the surface leakage.     

Fluorine-plasma treated AlGaN/GaN high electronic mobility transistors under off-state overdrive stress

Influences of off-state overdrive stress on the fluorine-plasma treated AlGaN/GaN high-electronic mobility transistors (HEMTs) are experimentally investigated. It is observed that the reverse leakage current between the gate and source decreases after the off-state stress, whereas the current between the gate and drain increases. By analyzing those changes of the reverse currents based on the Frenkel-Poole model, we realize that the ionization of fluorine ions occurs during the off-state stress. Furthermore, threshold voltage degradation is also observed after the off-state stress, but the degradations of AlGaN/GaN HEMTs treated with different F-plasma RF powers are different. By comparing the differences between those devices, we find that the F-ions incorporated in the GaN buffer layer play an important role in averting degradation. Lastly, suggestions to obtain a more stable fluorine-plasma treated AlGaN/GaN HEMT are put forwarded.     

AlGaN/GaN high-electron-mobility transistors with transparent gates by Al-doped ZnO

AlGaN/GaN high-electron-mobility transistors （HEMTs） with Al-doped ZnO （AZO） transparent gate electrodes are fabricated, and Ni/Au/Ni-gated HEMTs are produced in comparison. The AZO-gated HEMTs show good DC characteristics and Schottky rectifying characteristics, and the gate electrodes achieve excellent transparencies. Compared with Ni/Au/Ni-gated HEMTs, AZO-gated HEMTs show a low saturation current, high threshold voltage, high Schottky barrier height, and low gate reverse leakage current. Due to the higher gate resistivity, AZO-gated HEMTs exhibit a current-gain cutoff frequency （fT） of 10 GHz and a power gain cutoff frequency （fmax） of 5 GHz, and lower maximum oscillation frequency than Ni/Au/Ni-gated HEMTs. Moreover, the C-V characteristics are measured and the gate interface characteristics of the AZO-gated devices are investigated by a C-V dual sweep.     

Effect of heavy ion irradiation on the interface traps of AlGaN/GaN high electron mobility transistors

AlGaN/GaN high electron mobility transistors (HEMTs) were irradiated with heavy ions at various fluences. After irradiation by 2.1 GeV¹⁸¹ Ta³²⁺ ions, the electrical characteristics of the devices significantly decreased. The threshold voltage shifted positively by approximately 25% and the saturation currents decreased by approximately 14%. Defects were induced in the band gap and the interface between the gate and barrier acted as tunneling sites, which increased the gate current tunneling probability. According to the pulsed output characteristics, the amount of current collapse significantly increased and more surface state traps were introduced after heavy ion irradiation. The time constants of the induced surface traps were mainly less than 10 μs.