水/油型微乳液中球形及棒状钛酸锶钡纳米粒子的控制合成

Barium strontium titanate nanoparticles with spherical and rod-like morphologies were synthesized in water/Triton X-100/n-hexanol/cyclohexane quaternary reverse microemulsion solution. The influences of the molar ratio of water to surfactant (ω₀) and the concentration of reactants on the morphology and size of barium strontium titanate nanoparticles were studied. The structure, compositions and morphology of the prepared products were characterized by XRD, SAED, ICP, EDS and TEM. The results show that the obtained Ba_0.7Sr_0.3TiO₃ spherical nanoparticles with diameters of 20～100 nm and the Ba_0.7Sr_0.3TiO₃ nanorods with diameters of 70～120 nm and lengths up to 600～800 nm are a single crystal, with a cubic phase. The molar ratio for barium, strontium and titanate in products is about 0.7:0.3:1.     

钛酸锌的制备及其对高氯酸铵热分解的催化性能

ZnTiO₃ nanocrystals were prepared by sol-gel method, using Zn(NO₃)₂ and Ti(C₄H₉O)₄ in the topic. The as-prepared ZnTiO₃ nanocrystals were characterized by XRD, FTIR and TEM, and the catalytic performance of ZnTiO₃ nanocrystals of different contents for the ammonium perchlorate(AP)decomposition was investigated by thermal analysis. The results indicate that ZnTiO₃ with pure cube structure can be synthesized at 600 ℃ by this procedure,which was spheroid with particle size of about 60~100 nm. The results expressed that the low temperature decomposition peaks of AP is advanced by 17 ℃ and the high temperature decomposition peaks of AP is advanced by 24 ℃ when adding 5% nanoparticle ZnTiO₃ powder. The catalytic effects of ZnTiO₃ powders on the high temperature decomposition of AP are less than that of nanometer metal powders, but all the micron metal powders decrease the low decomposition temperature of AP.     

La2O2S∶Mn2+荧光粉的微波合成及其荧光特性

Using La₂(SO₄)3 and the active carbon powder as reactants, La₂O₂S∶Mn²⁺ red phosphor was synthesized by microwave radiation method. The phosphor was characterized by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), laser-diffraction size analyzer and fluorospectrophotometer. The XRD analysis showed that the phosphor was pure phase La₂O₂S. The phosphor of La₂O₂S∶Mn²⁺ showed hexagonal crystal structure with diverse shapes, such as spherical and rod, with average particle size of 10.22 μm. The emission and excitation spectra of the phosphor were determined by fluorospectrophotometer and the results showed that the excitation spectrum of the phosphor under 600 nm emission wavelength was excitation bands between 250 nm and 350 nm with a peak value of 303 nm. Then ,when exicited under UV 303 nm, the phosphor showed broad band emission of 550~700 nm with a peak at 607 nm. In addition, the optimal effects were obtained for the phosphor preparation when the concentration of the activator Mn²⁺ was x_Mn=0.01, the ratio of C and O (n_C / n_O) in the reactants was 0.6∶1, and the time of reaction was about 1 h. La₂O₂S∶Mn²⁺ has strong absorption of UV spectrum and can emit bright red light.     

溶胶凝胶法制备Nd2O3改性钛酸钡陶瓷的研究

The technological condition for the preparation of BaTiO₃ ceramics doped with Nd₂O₃ by Sol-Gel was deter-mined through orthogonal experiment. When n_Ba(Ac)2∶n_Ti(OC4H9)4∶n_Nd2O3∶n_{CH3(CH2)2CH2OH}∶n_H2O=1.00∶1.00∶0.003∶7.30∶37.04, pH=3.5,T=25℃,the light-yellow-transparent-stable solution and thorough transparent gel was generat-ed, the transforming time of solution to gel was 25h. The crystal structure and particle size of BaTiO₃ ceramics doped with Nd₂O₃ were studied by SEM and X-ray respectively, the type of the crystal was tetragonal, the particle size was about 24.7nm. The dielectric constant (ε) and dielectric loss (tanδ) of BaTiO₃ ceramics doped with Nd₂O₃ were determined between 10⁴～10⁶Hz, and the results showed that the dielectric constant was increased obviously, the dielectric loss was decreased clear and the resistivity (ρ_V) was also decreased noticeably.     

单分散超细ZnO粉体的制备与表征

Monodispersed superfine ZnO powders with particle size of about 200～400nm were successfully prepared by the decompressed distillation process with n-butyl alcohol as the solvent. The starting materials were Zn(NO₃)2·6H₂O and NH₃·H₂O. TG-DSC， XRD， TEM and BET surface areas techniques were used to characterize the precursor and as-prepared superfine ZnO powders. In the preparation process of superfine ZnO powders， two techniques including the decompressed distillation with n-butyl alcohol and washing with absolute ethanol were used to avoid agglomeration. It is showed that the decompressed distillation process has a better effect in avoiding ag-glomeration than washing with absolute ethanol. The precursor obtained by the decompressed distillation technique has a lower calcination temperature than the one obtained by washing with absolute ethanol. Zincite phase of ZnO with some impurities was obtained when the precursor was calcined at 200℃ for 2h. After it was calcined at 300℃ for 2h， pure superfine ZnO powder was obtained.     

微波辐照方式对CdS和Bi2S3纳米粒子结晶度的影响

The effect of traveling microwave irradiation on the crystallinities of CdS nanoparticles and Bi₂S₃ nanorods was studied. Results showed that as compared with stationary microwave irradiation the crystallinities and the crystal growth of sulfide nanoparticles were improved. Traveling microwave irradiation can supply narrower frequency distribution and stronger power density of irradiation， CdS nanoparticles and Bi₂S₃ nanorods obtained are better in crystallinities and larger in size than under stationary microwave irradiation.     

简捷水热前驱物技术制备钛酸钡纳米棒与纳米球

A facile synthesis route has been developed to prepare barium titanate nanoparitcles via a low temperature (120 ℃) hydrothermal decomposition of single-source metal-organic precursor. A mixture of tetramethylammonium hydroxide (TMAH) and distilled water was used as reaction media, and Barium titanium ethyl-hexano- isoproxide [BaTi(O₂CC₇H₁₅)(OC₃H₇)₅] was used as precursor. The architecture of products can be selectively controlled from nanorods to nanospheres by adjusting the precursor′s concentration in the reaction system. Powder X-ray diffraction (XRD) analysis indicated that the products were in cubic phase. Transmission electronic microscopy (TEM) observation showed that the nanospheres were 30～50 nm in diameter, and the nanorods were 5～10 nm in diameter and 100～600 nm in length, respectively. Phase transformation behavior of the as-prepared products was also investigated.     

结晶碳酸钕的水热合成、外观形貌及其组成

Crystalline neodymium carbonates were prepared by treating the amorphous precipitate formed from the reaction between neodymium chloride and ammonium bicarbonate under hydrothermal condition. Their composition, morphology and crystal phase were identified by means of elemental analysis, SEM and XRD. It was found that Nd₂(CO₃)₃·2.5H₂O with tengerite-type structure and sheet morphology was obtained when the feed molar ratio(FMR=n_(NH4)2CO2/n_NdCl3)was 2 or 1.8 and hydrothermally treated at 150 ℃ for 12h. However, orthogonal NdOHCO₃ particles agglomerated with long rod crystals were formed when lowering FMR to 1.5 under the same hydrothermal condition. Phase transformation from tengerite-type Nd₂(CO₃)₃·2.5H₂O to orthogonal NdOHCO₃ was occurred when increasing hydrothermal temperature or prolonging hydrothermal time, which is beneficial to the preparation of neodymium hydroxyl-carbonate with neodymium oxide content higher than 70%.     

反相微乳液法合成SrTiO3纳米棒

SrTiO₃ nanorods were synthesized in cetanyl trimethyl ammonium bromide (CTAB) reverse microemulsion containing CTAB, n-hexanol, n-octane and water with Ba(OH)₂ as reactants. The effects of different conditions such as ω₀ [ω₀=n_H2O/ n_CTAB], aging time and the concentration of reactants on the formation of the nanorods were studied. Transmission electron microscope (TEM), electron diffraction (ED) and X-ray diffraction(XRD)were used to characterize the morphology and the structure of the synthesized nanorods. The results show that SrTiO₃ nanorods with a length of 260～2 000 nm and a diameter of 50～100 nm belonging to single crystal are single cubic system. The molar ratio of Sr to Ti of products is 1.0 as determinded by ICP.     

VOx / Titanate复合材料纳米棒的水热合成及其电化学性能研究

Vanadium oxide/titanate composites nanorods (VO_x/ Titanate-CNRs) were synthesized in high yield by using titanate nanotubes as templates and V₂O₅·nH₂O sol as the precursors under hydrothermal conditions (200 ℃, 48 h). Samples were characterized with X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and energy dispersive analysis by X-ray (EDAX). X-ray diffraction structure determination showed that this new phase had the composition of V₃O₇·H₂O and crystallized with orthorhombic symmetry. SEM and TEM tests showed that the samples were uniform straight rods with the diameter range from around 100 to 300 nm and the length over 10 μm. The chemical compositions of the samples were determined with EDXA. The electrochemical tests of samples (titanates nanotubes, V₂O₅ and VO_x/ Titanate-CNRs) prove that VO_x/ Titanate-CNRs exhibit a better electrochemical performance.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.