Effect of Y2O3 Additions on the Densification of an Al2O3–TiC Composite

The densification of Al₂O₃–30TiC (in weight percent) composite is investigated as a function of Y₂O₃ additions. It is observed that very small amounts of Y₂O₃ are effective in aiding the densification. The density was observed to pass through a maximum at 0.35 wt% of Y₂O₃. The gas-generating reaction of Al₂O₃ with TiC is likely to be suppressed by the addition of Y₂O₃.     

Sintering ZrO2/TiC Composites with TiH2: The Role of Transient Liquid Phase and of Substoichiometry

Sintering tetragonal ZrO₂ with 35 vol% TiC results in a microstructure where all grain facets are free of amorphous interfaces independent of sintering aids as TiH₂ or MgO/ Y₂O₃; grain sizes are below 1 μm. With substoichiometric TiC_1-x, a relative density of 95% and closed porosity are obtained at a lower sintering temperature than with stoichiometric TiC, but subsequent cladless hot isostatic pressing (HIP) is required to achieve 99% density. High densities of 98% accompanied by good mechanical properties become possible by pressureless sintering with the use of TiH₂. MgO/Y₂O₃ doping also promotes densification, but results in less transformable zirconia and increases the number and size of amorphous triple junctions. The consequences are a lower fracture toughness and strength.     

Low-Temperature High-Pressure Consolidation of Amorphous Al2O3–15 mol% Y2O3

This study examined pressure consolidation of amorphous Al₂O₃–15 mol% Y₂O₃ powders prepared by co-precipitation and spray pyrolysis. The two amorphous powders had similar true densities and crystallization sequences. Uniaxial hot pressing was carried out at 450°–600°C with a moderate pressure of 750 MPa. The co-precipitated powder could be hot pressed to a maximum relative density of 98% and remained amorphous. Pressure adversely affected the densification of the spray-pyrolyzed powder by favoring an early crystallization of γ-Al₂O₃ phase at 580°C. Plastic deformation of the amorphous phase is believed to be responsible for the large densification of the amorphous powders.     

Reactive Hot-Pressed Alumina–Boron Nitride Composites with Y2O3 Sintering Additive

The effect of Y₂O₃ addition (0–5 wt%) on the densification and properties of reactive hot-pressed alumina (Al₂O₃)–boron nitride composites based on the reaction between aluminum borate (2Al₂O₃·B₂O₃) and aluminum nitride (AlN) was investigated. The densification process was very sensitive to the amount of Y₂O₃. Compared with a low relative density of 79.3 theoretical density (TD)% for material with no Y₂O₃ addition, the material density reached 98.6 TD% with 0.25% Y₂O₃ addition. High Y₂O₃ additions resulted in the formation of a new phase Al₅Y₃O₁₂. The grain growth of the Al₂O₃ matrix was promoted by the Y₂O₃ addition. Owing to the high density and the small Al₂O₃ particle size the sample with 0.25% Y₂O₃ addition demonstrated the highest bending strength of 540 MPa.     

Strength-Toughness Relations in Sintered and Isostatically Hot-Pressed ZrO2-Toughened Al2O3

The fracture toughness of fine-grained undoped ZrO₂-toughened Al₂O₃ (ZTA) was essentially unchanged by postsintering hot isostatic pressing and increased monotonically with ZrO₂ additions up to 25 wt%. The strength of ZTA with 5 to 15 wt% tetragonal ZrO₂, which depended monotonically on the amount of ZrO₂ present before hot isostatic pressing, was increased by pressing but became almost constant between 5 and 15 wt% ZrO₂ addition. The strength appeared to be controlled by pores before pressing and by surface flaws after pressing; the size of flaws after pressing increased with ZrO₂ content. The strength of ZTA containing mostly monoclinic ZrO₂ (20 to 25 wt%) remained almost constant despite the noticeable density increase upon hot isostatic pressing because the strength was controlled by preexisting microcracks whose extent did not change on postsintering pressing. These strength-toughness relations in sintered and isostatically hot-pressed ZTA are explained on the basis of R -curve behavior. The importance of the contribution of microcracks to the toughness of ZTA is emphasized.     

Pulse Electric Current Sintering of Al2O3/3 vol% ZrO2 with Constrained Grains and High Strength

The pulse electric current sintering technique (PECS) was demonstrated to be effective in rapid densification of fine-grained Al₂O₃/3Y-ZrO₂ using available commercial powders. The composites attained full densification (>99% of TD) at 1450°C in less than 5 min. The composites sintered at a high heating rate had a fine microstructure. The incorporation of 3 vol% 3Y-ZrO₂ substantially increased the average fracture strength and the toughness of alumina to as high as 827 MPa and 6.1 MPa·m^1/2, respectively. A variation in the heating rate during the PECS process influenced grain size, microstructure, and strength, though there was little or no variation in the fracture toughness.     

Postsintering Hot Isostatic Pressing of Ceria-Doped Tetragonal Zirconia/Alumina Composites in an Argon–Oxygen Gas Atmosphere

Ceria-doped tetragonal zirconia (Ce-TZP)/alumina (Al₂O₃) composites were fabricated by sintering at 1450° to 1600°C in air, followed by hot isostatic pressing (postsintering hot isostatic pressing) at 1450°C and 100 MPa in an 80 vol% Ar–20 vol% O₂ gas atmosphere. Dispersion of Al₂O₃ particles into Ce-TZP was useful in increasing the relative density and suppressing the grain growth of Ce-TZP before hot isostatic pressing, but improvement of the fracture strength and fracture toughness was limited. Postsintering hot isostatic pressing was useful to densify Ce-TZP/Al₂O₃ composites without grain growth and to improve the fracture strength and thermal shock resistance.     

Effect of Alkali Metal Oxide Addition on the Sinterability of MgO–B2O3–Al2O3 Glass–Al2O3 Filler Composites

The sintering of a composite of MgO–B₂O₃–Al₂O₃ glass and Al₂O₃ filler is terminated due to the crystallization of Al₄B₂O₉ in the glass. The densification of a composite of MgO–B₂O₃–Al₂O₃ glass and Al₂O₃ filler using pressureless sintering was accomplished by lowering the sintering temperature of the composite. The sintering temperature was lowered by the addition of small amounts of alkali metal oxides to the MgO–B₂O₃–Al₂O₃ glass system. The resultant composite has a four-point bending strength of 280 MPa, a coefficient of thermal expansion (RT—200°C) of 4.4 × 10⁻⁶ K⁻¹, a dielectric constant of 6.0 at 1 MHz, porosity of approximately 1%, and moisture resistance.     

Densification and Grain Growth of Al2O3 Nanoceramics During Pressureless Sintering

α - Al₂O₃ nanopowders with mean particle sizes of 10, 15, 48, and 80 nm synthesized by the doped α-Al₂O₃ seed polyacrylamide gel method were used to sinter bulk Al₂O₃ nanoceramics. The relative density of the Al₂O₃ nanoceramics increases with increasing compaction pressure on the green compacts and decreasing mean particle size of the starting α-Al₂O₃ nanopowders. The densification and fast grain growth of the Al₂O₃ nanoceramics occur in different temperature ranges. The Al₂O₃ nanoceramics with an average grain size of 70 nm and a relative density of 95% were obtained by a two-step sintering method. The densification and the suppression of the grain growth are achieved by exploiting the difference in kinetics between grain-boundary diffusion and grain-boundary migration. The densification was realized by the slower grain-boundary diffusion without promoting grain growth in second-step sintering.     

SiC-Whisker-Reinforced Al2O3 Composites by Free Sintering of Coated Powders

SiC whiskers were coated with a thick cladding of finegrained Al₂O₃ powder by controlled heterogeneous precipitation in a concentrated suspension of whiskers. After calcination, the coated whiskers were compacted by cold isostatic pressing and sintered at a constant heating rate of 5°C/min in a helium atmosphere. The parameters which control the coating process and the sintering characteristics of the consolidated powders are reported. Starting with an initial matrix density of 40–45% of the theoretical, composites containing up to ≅20 vol% whiskers (aspect ratio ≅15) were sintered freely to nearly theoretical density below 1800°C. By comparison, a similar composite formed by mechanical mixing of the whiskers and the precipitated Al₂O₃ powder reached a density of only 68% of the theoretical after sintering under identical conditions. For a fixed whisker content, the sinterability of the composites formed from the coated whiskers shows a fairly strong dependence on the whisker aspect ratio.     

Sintering, Crystallization, and Properties of B2O3/P2O5-Doped Li2O·Al2O3·4SiO2 Glass-Ceramics

Sintering, crystallization, microstructure, and thermal expansion of Li₂O·Al₂O₃·4SiO₂ glass-ceramics doped with B₂O₃, P₂O₅, or (B₂O₃+ P₂O₅) have been investigated. On heating the glass powder compacts, the glassy phase first crystallized into high-quartz s.s., which transformed into β-spodumene after the crystallization process was essentially complete. The effects of dopants on the crystallization of glass to high-quartz s.s. and the subsequent transformation of high-quartz s.s. to β-spodumene were discussed. The major densification occurred only in the early stage of sintering time due to the rapid crystallization. All dopants were found to promote the densification of the glass powders. The effect of doping on the densification can fairly well be explained by the crystallization tendency. All samples heated to 950°C exhibited a negative coefficient of thermal expansion ranging from about −4.7 × 10^-6 to −0.1 × 10^-6 K^-1. Codoping of B₂O₃ and P₂O₅ resulted in the highest densification and an extremely low coefficient of thermal expansion.     

Spark Plasma Sintering of Sol–Gel Derived Amorphous ZrW2O8 Nanopowder

Dense ZrW₂O₈ was prepared by spark plasma sintering (SPS), using amorphous ZrW₂O₈ nanopowder as a raw material, at 873 K for 10 min. We investigated the effects of SPS conditions, such as sintering temperature, heating rate, and the discharge power that is expressed as the product of pulsed direct current and voltage, on the densification process of ZrW₂O₈. The relative density and microstructure of ZrW₂O₈ prepared by SPS were compared with those of ZrW₂O₈ prepared by hot pressing (HP). The relative density of ZrW₂O₈ prepared by HP at 873 K for 1 h was 63.1%. On the contrary, the relative density of ZrW₂O₈ prepared by SPS at 873 K for 10 min at a heating rate of 50 K/min was 98.6%. These results show that the discharge pressure that is proportional to discharge power enhances the densification and grain growth of ZrW₂O₈ in the SPS process.     

Al2O3─SiC Composites from Aluminosilicate Precursors

Al₂O₃ and SiC composite materials have been produced from mixtures of aluminosilicates (both natural minerals and synthetic) and carbon as precursor materials. These composites are produced by heating a mixture of kaolinite (or synthetic aluminosilicates) and carbon in stoichiometric proportion above 1550°C, so that only Al₂O₃ and SiC remain as the major phases. A similar process has also been used for synthesizing other composite powders having mixtures of Al₂O₃, SiC, TiC, and ZrO₂ in different proportions (all compounds together or selective mixtures of some of them), as desired. The microstructure of hot-pressed dense compacts, produced from these powders, revealed that the SiC phase is distributed very homogeneously, even occasionally within Al₂O₃ grains on a nanosize scale. The homogeneous distribution of SiC particles within the system produced high fracture toughness of the hot-pressed material (K_IC∼ 7.0 MPa · m^1/2) and having Vicker's hardness values greater than 2000 kgf/mm².     

Pressureless Sintering of Alumina-Titanium Carbide Composites

The densification of Al₂O₃-TiC composites is detrimentally affected by chemical reactions between Al₂O₃ and TiC. These reactions must be suppressed in order to promote sintering. In this study, the specific reactions occurring in Al₂O₃-TiC composites were modeled, using thermodynamic calculations, and verified by experiments. The reaction between Al₂O₃ and TiC was suppressed by the use of specially prepared embedding powders allowing pressureless sintering to closed porosity. The Al₂O₃-TiC composites were subsequently hot isostatically pressed to > 99% of theoretical density without encapsulation. Typical flexural strength and fracture toughness of Al₂O₃-30 wt% TiC composites were 690 MPa and 4.3 MPa · m^1/2, respectively.     

Hot Isostatic Processing of Shocked Si3N4 Powder

To enhance the sinter ability of Si₃N₄, powders mixed with 0, 2, and 5 wt% Y₂O₃ were explosively shock-treated. Compacts of these powders were encapsulated in 96% silica glass containers and isostatically hot-pressed. The shocked Si₃N₄ with 5 wt% Y₂O₃ was pressed to a density of 3.09 g/cm³ (95.4% of theoretical) at 1400°C under 430 MPa for 3 h, whereas the unshocked material attained only 82.4% of theoretical density under the same hot isostatic pressing conditions.     

Field-Assisted Densification of Superhard B6O Materials with Y2O3/Al2O3 Addition

B₆O is a possible candidate of superhard materials with a hardness of 45 GPa measured on single crystals. Up to now, densification of these materials was only possible at high pressure. However, recently it was found that Al₂O₃ can be utilized as an effective sintering additive, similar to the addition of Y₂O₃/Al₂O₃ that was used in this work. The densification behavior of the material as a function of applied pressure, its microstructure evolution, and the resulting mechanical properties were investigated. A strong dependence of the densification with increasing pressure was found. The material revealed characteristic triple junctions filled with amorphous residue composed of B₂O₃, Al₂O₃, and Y₂O₃, while no amorphous grain-boundary films were observed along internal interfaces. Mechanical testing revealed on average a hardness of 33 GPa, a fracture toughness of 4 MPa·m^1/2, and a strength value of 520 MPa.     

Preparation and Microstructure of Multi-Wall Carbon Nanotubes-Toughened Al2O3 Composite

With multi-wall carbon nanotubes (MWNTs) as reinforcement, a 12 vol% MWNTs/alumina (Al₂O₃) ceramic composite was obtained by hot pressing. A fracture toughness of 5.55±0.26 MPa·m^1/2, 1.8 times that of pure Al₂O₃ ceramics, was achieved. Experimental results showed that the enveloping of carbon nanotubes (CNTs) with sodium dodecyl sulfate (SDS) is effective in changing the hydrophobicity of CNTs to hydrophilicity and improving the dispersion of CNTs in aqueous solution. Enveloped with SDS, CNTs can be homogeneously mixed with Al₂O₃ at a microscopic level by heterocoagulation. This mixing method can obviously improve the chemical compatibility between CNTs and Al₂O₃, which is important for enhancement of interfacial strength between them.     

Sintering of Partially Stabilized Zirconia by Microwave Heating Using ZnO–MnO2–Al2O3 Plates in a Domestic Microwave Oven

Partially stabilized zirconia (PSZ) powders were fully densified by microwave heating using a domestic microwave oven. Pressed powder compacts of PSZ were sandwiched between two ZnO–MnO₂–Al₂O₃ ceramic plates and put into the microwave oven. In the first step, PSZ green pellets were heated by self-heating of ZnO–MnO₂–Al₂O₃ ceramics (1000°C). In the second step, the heated PSZ pellets absorbed microwave energy and self-heated up to a higher temperature (1250°C), leading to densification. The density of PSZ obtained by heating in the microwave oven for 16 min was 5.7 g/cm³, which was approximately equal to the density of bodies sintered at 1300°C for 4 h or 1400°C for 16 min by the conventional method. The average grain size of the sample obtained by this method was larger than the average grain size of samples sintered by the conventional method with a similar heating process.     

Effect of Processing Parameters on the Mechanical and Microstructural Behavior of Ultra-Fine Al2O3– (ZrO2+8%Mol Y2O3) Bioceramic, Densified By High-Frequency Induction Heat Sintering

High-frequency induction heat sintering (HFIHS) is a comparatively new technique that consolidates metals and ceramics very rapidly to full density. In this work, superfast densification behavior and the attendant microstructural features of Al₂O₃–(ZrO₂+8% mol Y₂O₃) composites processed by HFIHS were investigated. The effects of processing parameters such as sintering temperatures, pressures, and heating rate, on the mechanical and microstructural properties were studied. The results indicated that HFIHS was effective in the preparation of fine-grained, nearly fully dense Al₂O₃–8YSZ ceramics from the powder with a smaller particle size by optimizing the overall processing parameters.     

Electroconductive Al2O3–NbN Composites

Electroconductive Al₂O₃–NbN ceramic composites were prepared by hot pressing. Dense sintered bodies of ball-milled Al₂O₃–NbN composite powders were obtained at 1550°C and 30 MPa for 1 h under a nitrogen atmosphere. The bending strength and fracture toughness of the composites were enhanced by incorporating niobium nitride (NbN) particles into the Al₂O₃ matrix. The electrical resistivity of the composites decreased with increasing amount of NbN phase. For a 25 vol% NbN–Al₂O₃ composite, the values of bending strength, fracture toughness, Vickers hardness, and electrical resistivity were 444.2 MPa, 4.59 MPa·m^1/2, 16.62 GPa, and 1.72 × 10⁻²Ω·cm, respectively, making the composite suitable for electrical discharge machining.