异戊二烯在Nd(naph)_3-Al(i-Bu)_3-Al_2(C_2H_5)_3Cl_3催化体系作用下聚合动力学

本文研究了异戊二烯在稀土催化剂作用下聚合动力学的一般规律。通过稳态处理及分段聚合证明,体系的活性中心数目基本稳定。聚合转化率低于50％时,聚合速率与单体浓度呈一级关系,同催化剂浓度为1.7级关系。聚合表观活化能为9.0千卡/克分子。聚合物的特性粘数随转化率增加而增大的事实,说明本体系具有某些“活性”聚合的特性。     

COPOLYMERIZATION OF BUTADIENE AND ISOPRENE CATALYZED BY V(acac)_3-Al(i-Bu)_2Cl-Al_2Et_3Cl_3 CATALYST AND CHARACTERIZATION OF THE PRODUCTS

Copolymerization of butadiene and isoprene catalyzed by the catalyst system V(acac)_3-Al(i-Bu)_2Cl-Al_2Et_3Cl_3 has been studied. Composition, microstructure, crystallinity and melting point of the copolymer obtained were determined by PGC, IR, X-ray diffraction and DSC methods respectively. The results revealed that the product was a copolymer and not a blend. The butadiene units presented in the copolymer were of trans-1,4-configuration, while the isoprene units were of both trans-1,4-and 3,4-forms. The melting point and crystallinity of the copolymer decrcascd with increase of molar ratio of isoprene to hutadiene.     

在稀土体系催化下的丁二烯聚合动力学

本文应用键谷勤聚合动力学公式进行动力学研究。求出了活性中心数目,有关的动力学常数和聚合速度方程(R_p=k_p[C~*][M])并着重研究了聚合物活性链性质。 在链引发阶段,发现20℃和50℃聚合,属于迅速引发类型,在0℃时则是缓慢引发类型。聚合过程中,存在明显的链转移反应。Al(i-C_4H_9)_3是主要的链转移剂。在50℃聚合时,有活性中心失活现象发生,并表明其为双基终止。     

RADIATION-INDUCED EMULSION POLYMERIZATION OF STYRENE IN SOAP-FREE SYSTEM

Radiation-induced emulsion polymerization of styrene in soap-free system has beenstudied and the monodisperse polystyrene lattices were obtained. Both its purity and emulsionconversion are better than that of chemically initiated polymers.     

稀土催化体系Nd(napb)_3-AlEt_2Cl-Al(i-Bu)_3对双烯烃聚合的活性

分析了催化剂Nd(naph)_3-AlEt_2Cl-Al(i-Bu)_3三组分反应产物的组成,用动力学方法研究了其催化异戊二烯聚合的活性。催化剂各组分的配比及制备方法对其活性及利用率有显著影响。催化剂的利用率随它使用时浓度的减小而增大,最后达到恒定链终止反应由体系中过量的AlEt_2Cl吸附于活性体而发生。     

STUDIES ON THE KINETICS OF PROPYLENE POLYMERIZATION WITH THE COMPLEXTYPE TiCl_3 CATALYST

The active center concentration C_p, the rate constant k_p, and the activation energy of chain propagation E_p in the polymerization of propylene with complex-type TiCl_3-(C_2H_5)_2AlCl catalyst system were studied. The Mn was corrected by (?) value determined by GPC. The values thus obtained for C_p, k_p, and E_p at 50℃were 3.01 mol/mol Ti, 6.27 1/mol·sec, and 5.10 Kcal/mol respectively.The kinetic parameters were compared with those obtained from conventional TiCl_3·AlCl_2 catalyst, showing that the higher activity of the complex-type catalyst over the conventional catalyst is not only due to the higher C_p of the former, but to a greater extent due to the increase of the k_p value.     

KINETICS OF POLYMERIZATION OF METHYL METHACRYLATE INITIATED BY COPPER POLYPROPYLENE-BASED POLYAMIDOXIME-SODIUM SULFITE SYSTEM*

The aqueous polymerization of methyl methacrylate initiated by copper polypropylene-based polyamidoxime (PPAO-Cu) -sodium sulfite system was investigated. The overall rate of polymerization (R_p) isR_p=9.7 x 10~(12) e~(-21.200/RT) [MMA]~(O.88)[Na_2 SO_3]~(0.50)The length of the induction period (τ) is inversely proportional to the concentration of sodium sultite and independent of the amount of polymer supported copper and the concentration of monomer. It could be expressed as follows:1/τ=1.2x10~(12)e~(-15.600/RT)[Na_2SO_3]=K_τR_iThe polymerization is initiated by a primary radical generated from the redox reaction rather than induced by "coordination-proton transfer" mechanism.     

THE EFFECT AND FUNCTION OF AliBu_2OR'''' ON BUTADIENE-PROPYLENE ALTERNATING COPOLYMERIZATION CATALYZED BY VO(OR)_2Cl-AIiBu_3 SYSTEM

Four kinds of AliBu_2OB' with different R' were synthesized. The effect of AliBu_2OR'/AliBu_3 mole ratio on the conversion, the [η] of copolymer and catalytic efficiency were studied. The conversion was increased obviously and the catalytic efficiency was 2.7 times higher than before. The effect of the amount of AliBu_2OR' on the valence state of vanadium ion and the change of the valence state of vanadium ion with reaction temperature and time were studied. The VIS and IR spectra of the trinary-component catalyst system were measured. The model of active center including AliBu_2OR' was proposed. The function of AliBu_2OB was explained.     

甲基丙烯酸丁酯的Nd（Oct）3—Al（i—Bu）3配合催化聚合

甲基丙烯酸丁酯(BMA)在2-乙基己酸钕[Nd(Oct)_3]和三异丁基铝[Al(i-Bu)_3]配合催化下的聚合反应结果表明。以正己烷和石油醚为溶剂的聚合转化率高于甲苯和四氢呋喃体系。4种不同配体的钕盐的聚合转化率差别不大。但是,以Nd(Oet)_3-Al(i-Bu)_3为催化剂时聚甲基丙烯酸丁酯的分子量最高。聚合反应速度与单体浓度和催化剂浓度均成一次方关系。甲基丙烯酸丁酯的聚合反应活化能为47.40kJ/mol。     

STUDIES ON THE POLYMERIZATION OF β-CYCLODEXTRIN WITH EPICHLOROHYDRIN*

Different proportions of β-cydodextrin and epichlorohydrin were used to prepare a group of β-cyclodextrin polymers. The relationship between the reaction extent and the molar ratios of reactants was discussed according to the results of ~1H-NMR, ~(13) C-NMR spectra and elemental analysis. Especially, high resolution ~1H-NMR spectra were usd for studying the reaction active sites and the extent of reaction. The solubility of oil soluble drugs in water was largely improved in the presence of water-soluble β-cyclodextrin polymer.     

POLYMERIZATION OF OCTAMETHYLCYCLOTETRASILOXANE WITH HEXAMETHYLDISILAZYL-LITHIUM AS INITIATOR*

 This work focused on the anionic polymerization of octamethylcyclotetrasiloxane (D₄, D = Me₂SiO_2/2) initiated by a new kind of initiator hexamethyldisilazyl-lithium (MM^NLi). ²⁹Si-NMR spectroscopy and gas chromatography (GC) were used to characterize the polymerization products. The process was accelerated by adding a small amount of high activity monomer D₃ and by raising the polymerization temperature. At the end of polymerization more than 95% of the monomer was converted to polymer and only a very small amount ofD₄ and D₅ remained in the polymers.     

NEW CATALYTIC SYSTEMS FOR THE FIXATION OF CO2 Ⅲ.INFLUENCE OF ADDITIVES AND REACTION MEDIUM ON THE COPOLYMERIZATION OF CARBON DIOXIDE-EPICHLOROHYDRIN IN THE PRESENCE OF Nd (P204)3-Al(i-Bu)3*

Copolymerization of carbon dioxide with epichlorohydrin was successfully carried out by usingNd(P_(204))_3-Al(i-Bu)_3 as catalyst (P_(204))=(RO)_2 POO--,R=CH_3 (CH_2),CH(C_2H_5) CH_2--). Addi-tion of carbonyl compounds into the catalyst decreased the carbon dioxide content of the copoly-mer to some extent. Compared to nonpolar solvents, ethereal and moderate polar solvents werefavourable to obtaining higher carbon dioxide content copolymer. The coincidence of these resultswith the assumed copolymerization scheme clearly indicated that the copolymerization proceeds via coordinate anionic mechanism.     

THE POLYCONDENSATION OF TEREPHTHALOYL CHLORIDE AND p-PHENYLENEDIAMINE HYDROCHLORIDE IN NMP-CaCl_2 SOLVENT SYSTEM

The solution polycondensation of 1,4-phenylenediamine hydrochloride and terephthaloyl chlo-ride with introducing a tertiary amine in NMP-CaCl_2 solvent system were studied in detail.Effect of reactant concentration, the content of CaCl_2, in NMP solvent and the kinds of tertiary amineon inherent viscosity of PPTA polymer have been studied. High molecular weight PPTA withinherent viscosity over 5 was obtained at 0.35Mol/L of reactant concentration in a solvent of NMP-CaCl_2 with the presence of α-picoline.     

Pd(PBu 3 t ) Adducts of Os3(CO)12. Synthesis and Structures of Pd2Os3(CO)12(PBu 3 t )2 and Pd3Os3(CO)12 (PBu 3 t )3

Two new compounds Pd₂Os₃(CO)₁₂ , 13 and Pd₃Os₃(CO)₁₂ , 14 have been obtained from the reaction of with Os₃(CO)₁₂ at room temperature. The products were formed by the addition of two and three groups to the Os–Os bonds of Os₃(CO)₁₂. Compounds 13 and 14 interconvert between themselves by intermolecular exchange of the groups in solution. Compounds 13 and 14 have been characterized by single crystal X-ray diffraction analyses.Dedicated to Professor Brian F. G. Johnson on the occasion of his retirement – 2005.     

在Nd(OCt)3*-HAl(i-Bu)2-CH2-CHCH2Cl均相催化体系下的丁二烯聚合动力学

本文研究了丁二烯在2-乙基己酸钕-氢化二异丁基铝-烯丙基氯均相催化体系下的聚合动力学。实验结果表明,聚合速率对单体浓度和主催化剂浓度均为一级关系,对氢化二异丁基铝浓度呈1/3级关系。测得了丁二烯在本体系中聚合的表观与增长活化能以及活性中心数目。     

PLASMA POLYMERIZATION OF HEXAMETHYLCYCLOTRISILOXANE

In a capacitively coupled RF discharge system with external electrodes ,hexamethyicyclotrisiloxane was polymerized, and the effects of discharge power and plasma gas on polymer deposition rate were studied. The polymer structures and properties were studied by IR spectroscopy, XPS measurement, PGC/MS combined technique, TG analysis and contact angle measuring. The results showed that the polymers prepared in H_2 or O_2 have higher C/Si ratio in comparison with those prepared in inert gases. PGC/MS results revealed the existence of many short carbon chains in the polymer structure .TG analysis suggested that the polymers prepared in the inert gas would possess better thermal stabilities.     

Nd(O-i-Pr)3-Al(i-Bu)3配位催化甲基丙烯酸甲酯聚合反应的研究

甲基丙烯酸甲酯(MMA)能以自由基引发聚合,也能以格氏试剂、烷基锂或烷基铝引发阴离子聚合[1].六十年代来,ABE等人研究了Ti、V、Cr、Co、Mn等的Ziegler-Natta催化剂的催化聚合反应,提高聚合物的规整性[2].近年来出现了稀土配位催化聚合MMA及其它丙烯酸酯的报道[2～7],但较少有Nd(O-i-Pr)3配位催化MMA聚合的报道.     

MoCl4-(i-Bu)2AlOAr体系引发丁二烯聚合的研究

 由MoCl₄为主催化剂,(i-Bu)_3Al与酚类反应的产物(i-Bu)₂AlOAr为助催化剂所组成的催化体系,在加氢汽油中引发丁二烯聚合,研究酚类结构对聚合反应的影响。结果表明,带有推电子基团的酚类,可以提高丁二烯岵,聚合速度,其顺序为双酚A>间甲酚间>β-萘酚>苯酚>对氯酚。测定了丁二烯聚合的表现活化能E_α,催化剂利用率α,活性中心浓度[P*],和活性中心的平均寿期L。     

CONFIGURATION OF VO(OR)_2Cl-Al(i-Bu)_3 CATALYST SYSTEM AND CHARGE DISTRIBUTION OF VANADIUM CENTRAL ION

According to the caiculation of quantum chemistry it come be deduced that conngurauons or the catalysts VO(OR)_2Cl-Al (i-Bu)_3, for the alternating Copolymerization of butadiene with propene, the highest reactive configuration was A. When the catalyst complex forms the configuration A, the energy of the system was the lowest; the central vanadium atom had relatively high positive charge and whose frontier orbital overlapped easily with the frontier orbital of butadiene to form coordination complex, so it was concluded from the experimental results and calculations that the configuration of the catalyst of relatively high activity was A.     

THE ROTATION BARRIER OF ELECTRON SPIN PROBE IN THE STUDY OF POLYMER SYSTEM

In the study of molecular motion of polymer by means of ESR in combination with spin probe, owing to that the ESR spectrum depicts only the behavior of spin probe, the information obtained is of indirect nature. Hence the relationship between them must first be investigated before any conclusion could be drawn. In this paper, two parameters T_R and C_R are introduced to characterize the changing of tumbling rate of spin probe, and the concept of rotation barrier of spin probe is proposed. It is considered that the magnitude of the rotation barrier is determined by the internal cavity size and distribution in polymer. When the temperature is raised, the size and distribution of the cavities change accordingly, thus the tumbling of spin probe changes gradually from a slower to a higher rate.