The use of a polymer inclusion membrane in flow injection analysis for the on-line separation and determination of zinc

This paper reports the first use of a polymer inclusion membrane (PIM) for on-line separation in flow injection analysis (FIA) involving simultaneous extraction and back-extraction. The FIA system containing the PIM separation module was used for the determination of Zn(II) in aqueous samples in the presence of Mg(II), Ca(II), Cd(II), Co(II), Ni(II), Cu(II), and Fe(III). The Fe(III) and Cu(II) interferences were eliminated by off-line precipitation with phosphate and on-line complexation with chloride, respectively. The concentration of Zn(II) was determined spectrophotometrically using 4-(2-pyridylazo) resorcinol (PAR). The optimal composition of the PIM consisted of 40% (m/m) di(2-ethlyhexyl) phosphoric acid (D2EHPA) as carrier, 10% (m/m) dioctyl phthalate (DOP) as plasticizer and 50% (m/m) poly(vinyl chloride) (PVC) as the base polymer. The optimized FIA system was characterized by a linear calibration curve in the range from 1.0 to 30.0 mg L⁻¹ Zn(II), a detection limit of 0.05 mg L⁻¹ and a relative standard deviation of 3.4% with a sampling rate of 4 h⁻¹. Reproducible results were obtained for 20 replicate injections over a 5 h period which demonstrated a good membrane stability. The FIA system was applied to the determination of Zn(II) in pharmaceuticals and samples from the galvanizing industry and very good agreement with atomic absorption spectrometry was obtained.     

Facilitated Cd(II) transport across CTA polymer inclusion membrane using anion (Aliquat 336) and cation (D2EHPA) metal carriers

PIMs have been involved as affinity membranes for recovery of metals (Cd, Pb, Zn) by facilitated transport from aqueous solutions under different speciation forms, either anionic or cationic. The motivation of this work is to compare the efficiency of the recovery process in the case of Cd(II) using extractants such as D2EHPA and Aliquat 336 that can form complexes with the cation Cd²⁺ or the anions CdCl₃⁻ and CdCl₄²⁻, respectively. The maximal Cd(II) recovery factors obtained in 8 h are 97.5% and 91.8% with D2EHPA and Aliquat 336, respectively. Although the transport fluxes with both carriers are not strongly different (ca. 2 μmol m⁻² s⁻¹), the recovery process in case of mixture of metals is better achieved with Aliquat 336. PIMs have shown a very good stability and a constancy of the transmembrane transport flux over 12 replicate measurements, each one lasting for 8 h repeated every 24 h.     

Polymer inclusion membranes: The concept of fixed sites membrane revised

The mechanism of facilitated transport of metal ions across polymer inclusion membranes (PIMs) is revised on the basis of transport flux measurements and of new data brought by techniques sensitive to local inter-molecular interactions and molecular diffusion. Cellulose triacetate (CTA) membranes built with two types of inclusion carriers: a liquid one Aliquat 336 and a crystalline one Lasalocid A, both able to carry metal ions across PIMs and supported liquid membranes (SLMs) made of the same components, have been compared. Both PIM systems show similar effects for what concern the need of a carrier threshold concentration for the occurrence of a transport flux across PIM as revealed by flux and fluorescence correlation spectroscopy (FCS) measurements, and the dependence of the chemical nature of plasticizers on the metal ion flux. These systems also present similar Raman and far IR signatures of structural evolution of PIMs with the increase of the carrier concentration within the CTA matrix.

All the presented data are interpreted as concern PIMs, according to an evolution of chemical interactions between components of the polymeric membrane able to lead to a phase transition. This phase transition type of the carrier-plasticized polymer system is induced by the increase of carrier concentration in the polymer chains. The PIM progressively organizes itself like a liquid SLM because of the enhancement of preferential solvent interactions between the carrier and the plasticizer.

The main conclusion of this study is that the classically adopted “hopping” transport mechanism between fixed carrier sites in a PIM does not apply to such carrier chemically unbound to polymer membrane systems.     

On-line determination of mercury(II) by membrane separation flow injection analysis

A rapid and inexpensive gas-diffusion (GD) flow injection method for the on-line determination of Hg(II) in aqueous samples is described. The analytical procedure involves the injection of a Hg(II) sample into a 1.5 M H₂SO₄ carrier stream which is merged with a reagent stream containing 0.6% SnCl₂ and 1.5 M H₂SO₄. Under these conditions Hg(II) is reduced to metallic mercury which partially evaporates through a Teflon membrane into an acceptor stream containing 1.75×10⁻⁴ M KMnO₄ in 0.3 M H₂SO₄. The decrease in the absorbance of the acceptor stream at 528 nm corresponding to the absorption maximum of the permanganate anion can be related to the original concentration of Hg(II) in the sample. The method is characterized by a detection limit of 4 μg l⁻¹ and a sampling frequency of 8 h⁻¹. The flow system was successfully applied to the analysis of river samples spiked with Hg(II).     

Selective preconcentration and determination of iodine species in milk samples using polymer inclusion sorbent

A method to determine low levels of iodine species namely I⁻ and IO₃⁻ in aqueous samples was developed and applied to milk and milk powder samples. It is based on selective preconcentration of I⁻ in polymer inclusion sorbent (PIS) and neutron activation analysis (NAA) of I⁻ sorbed in PIS. The PIS was found to be highly selective for I⁻ in presence of IO₃⁻ and other anions commonly present in the milk samples. In order to preconcentrate total I⁻ + IO₃⁻ content in the PIS, IO₃⁻ was reduced to I⁻ using a mixture of acetic acid and ascorbic acid. It was found that total iodine content in milk could be determined with epithermal neutron activation analysis (ENAA). A scheme was developed to determine I⁻, IO₃⁻ and total iodine. The developed method was applied to milk reference materials (NIST SRM-1549 and IAEA-RM-153 milk powder) and a commercially available milk powder. The scheme for estimation of iodine in different forms was validated by using reference material NIST SRM-1549.     

Sequential injection spectrophotometric determination of orthophosphate in beverages, wastewaters and urine samples by electrogeneration of molybdenum blue using tubular flow-through electrodes

A novel and automated sequential injection procedure is proposed for the spectrophotometric determination of orthophosphate without requiring unstable chemical reducing species used in the classical molybdenum blue method. The flowing methodology is based on the on-line generation of the detectable species by electrochemical reduction of the 12-molybdophosphoric acid complex using a stainless steel tubular flow-through working electrode. The established method is linear up to 20 mg/l P, with coefficients of variation (n=10) of 2.4 and 1.8% for 2.0 and 10 mg/l P, respectively. The versatility of the sequential injection method to analyse samples containing high orthophosphate levels has been demonstrated by the implementation of a dilution chamber as well as flow-reversal techniques, yielding relative standard deviations (n=17) better than 2.0% for standards containing 200 and 800 mg/l P. The proposed analyser features an extremely wide dynamic range (viz., 0.3-800 mg/l) as well as improved tolerance to silicate interference, so that Si/P ratios higher than 50 are tolerated at the 5% level. Electrochemical conditions, reagent concentrations and physical variables have been thoroughly investigated. The method has been applied to the determination of orthophosphate in wastewaters as well as beverages and biological samples containing high concentrations of the target analyte. The t-test comparison of the means for the developed sequential injection system with electroreduction and both the molybdenum blue classical spectrophotometric batch procedure and inductively coupled plasma-optical emission spectrometric detection selected as external reference methods revealed that there is no evidence of significant differences between the obtained results at the 95% confidence level.     

The use of a polymer inclusion membrane in a paper-based sensor for the selective determination of Cu(II)

A disposable paper-based sensor (PBS) is described for the determination of Cu(II) in natural and waste waters at approximately 2 cents per measurement. The device makes use of a polymer inclusion membrane (PIM) to provide the selectivity for Cu(II). The PIM consists of 40 wt% di(2-ethlyhexyl) phosphoric acid (D2EHPA) as the carrier, 10 wt% dioctyl phthalate (DOP) as a plasticizer, 49.5 wt% poly(vinyl chloride) (PVC) as the base polymer and 0.5 wt% (m m⁻¹) 1-(2′-pyridylazo)-2-naphthol (PAN) as the colourimetric reagent. High selectivity under mildly acidic conditions (HCl, pH 2.0) is achieved for Cu(II) in the presence of frequently encountered metal ions in natural and waste waters such as Fe(III), Al(III), Zn(II), Cd(II), Pb(II), Ca(II), Mg(II), and Ni(II).     

Determination of oxytetracycline in milk samples by polymer inclusion membrane separation coupled to high performance liquid chromatography

The determination of oxytetracycline in milk samples using a polymer inclusion membrane concept with high performance liquid chromatography (HPLC) was studied. The membranes developed are composed by cellulose acetate as polymer base, Cyanex 923 as carrier and o-nitrophenyl octyl ether as plasticizer. In the optimal conditions, the method exhibits good linearity in the range 0.03–0.20 mg L⁻¹ with a limit of detection and quantification of 8.2 and 27.3 μg L⁻¹ respectively. The method was successfully applied to the analysis of milk samples with high selectivity.     

The effect of the counter anion on the transport of thiourea in a PVC-based polymer inclusion membrane using Capriquat as carrier

This paper describes the effect of four counter anions (CH₃COO⁻, Cl⁻, NO₃⁻, ClO₄⁻) of the trioctylmethylammonium (TOMA) cation on the rate of solvent extraction of thiourea and its transport across poly(vinyl chloride) (PVC)-based polymer inclusion membranes (PIMs). The membranes also contained 2-nitrophenyl octyl ether (NPOE) as the plasticizer while chloroform was used as diluent in the solvent extraction studies. It is demonstrated that the counter anion affects substantially the rate of membrane transport and the degree of extraction follows the order: CH₃COO⁻ > Cl⁻ > NO₃⁻ ? ClO₄⁻. The transport rate is negligible for the perchlorate anion. This order is consistent with thiourea interacting with the counter anion through hydrogen bonding to form a heteroconjugate anion.     

On-line coupling of flow injection displacement sorption preconcentration to high-performance liquid chromatography for speciation analysis of mercury in seafood

A simple and cost-effective method for speciation analysis of trace mercury in seafood was developed by on-line coupling flow injection microcolumn displacement sorption preconcentration to high-performance liquid chromatography (HPLC) with UV detection. The methodology involved the presorption of the Cu-PDC (pyrrolidine dithiocarbamate) chelate onto a microcolumn packed with a cigarette filter sorbent, simultaneous preconcentration of Hg(II), methylmercury (MeHg), ethylmercury (EtHg), and phenylmercury (PhHg) onto the microcolumn through a displacement reaction with the presorbed Cu-PDC, and their subsequent elution from the microcolumn for on-line HPLC separation. Interferences from heavy metal ions with lower stability of their PDC chelates relative to Cu-PDC were minimized without the need of any masking agents. With the consumption of 4.0 ml of sample solution, the enrichment factors were about 80. The detection limits were 10-25 ng g(-1) (as Hg) in fresh tissue. Precision (R.S.D. (%), n = 5) ranged from 2 to 3% at the 500 microg l(-1) (as Hg) level. The developed technique was validated by analyzing a certified reference material (DORM-2, dogfish-muscle), and was shown to be useful for mercury speciation in real seafood samples.     

基于碘离子选择性电极的流动注射分析系统构建

碘硫(IS)热化学循环分解水是目前最有前景的核能制氢技术.在IS循环研究中,I-浓度的在线分析对于实现过程反应条件的监测控制以及进行有关反应动力学研究非常重要.以碘离子选择性电极为检测器,针对IS循环物料组成体系组装了一套流动注射分析系统,考察了样品温度、氢离子浓度、离子强度等因素对电极性能的影响,对FLA装置的栽流流...     

Design of a field flow system for the on-line spectrophotometric determination of phosphate, nitrite and nitrate in natural water and wastewater

This study describes the design and optimisation of a field flow system for the in-situ collection and on-line determination of phosphate, nitrate and nitrite by flow injection analysis-spectrophotometry. The method is based on the initial determination of phosphate as its phosphoantimonylmolybdenum blue complex which is then oxidized on-line by nitrite and the decrease in absorbance is monitored at 880 nm. Nitrate is determined as the difference between total and initial nitrite content in a separate flow after reduction to nitrite in a cadmium reductive column. The calibration curves were linear in the range 0–2.00 mg L⁻¹ P-phosphate, 0–10.00 mg L⁻¹ nitrite and 0–7.00 mg L⁻¹ nitrate with correlation coefficients of 0.9979, 0.9993 and 0.9995, respectively. The detection limits, calculated as 3S/N, were 0.15 mg L⁻¹ for P-phosphate, 0.17 mg L⁻¹ for nitrite and 0.09 mg L⁻¹ for nitrate. The reproducibility was below 3.0% (n = 7). Method validation in the analysis of natural water and wastewater samples revealed that it can efficiently be applied to the determination of the target analytes, with recoveries in the range of 92–108%. Correspondence: Athanasios G. Vlessidis, Laboratory of Analytical Chemistry, Department of Chemistry, University of Ioannina, Ioannina 45110, Greece     

Simultaneous determination of silicate and phosphate in boiler water at power plants based on series flow cells by using flow injection spectrophotometry

A new flow injection spectrophotometric method is described for the simultaneous determination of silicate and phosphate. Effects on the sensitivity of the method of the wavelength, temperature, length of reaction coils, pump rates, acidity, sampling volume, concentration of the chromogenic reagent, etc. were also investigated. The optimum conditions were ascertained.The principle of the method is that total concentration of silicate plus phosphate is determined when a injected sample plug is passing through the first flow cell and then the concentration of silicate is serially) determined at a second flow cell of the same detector after continuously masking the yellow molybdophosphate in the sample zone. Finally, the concentration of phosphate is obtained by difference.Silicate and phosphate are determined in boiler water at power plants; 60-120 samples h⁻¹ be analyzed. Determination ranges are 0.05-22 mg l⁻¹ for silicate and 0.1-24 mg l⁻¹ for phosphate. Relative standard deviations for metasilicate and orthophosphate were ≤1.2 and 1.3%, respectively. Recovery ranges of silicate and phosphate in the samples are 98-103%.     

11-Molybdobismuthophosphate—A new reagent for the determination of ascorbic acid in batch and sequential injection systems

The guanidinium salt of the new heteropolymolybdate 11-molybdobismuthophosphate Gua₆PBiMo₁₁O₄₀ (11-MBP) was synthesized, characterized and used as a reagent for batch spectrophotometric (SP) and sequential injection determination of ascorbic acid (AsA). When compared to other Keggin's heteropolyanions, the reduction of 11-MBP with AsA is both fast and maximal within a pH range of 1.6-2.0. The stoichiometry of the reaction was determined using molar ratio and continuous variation methods and was shown to be 1:1. The molar absorptivity of the reduced form of 11-MBP was 6.0 × 10³ L mol⁻¹ cm⁻¹ at 720 nm. The reaction is also specific for AsA. Only cysteine, hydroquinone and hydroxyacids were found to interfere with the reaction, while no interference was observed with the common reducing agents, including reducing sugars, catecholamines, nitrite, sulfite and iron(II) ions. Batch SP and sequential injection analysis (SIA) systems were developed for the determination of AsA, with calibration ranges of the SP methods at 2 × 10⁻⁶-8 × 10⁻⁵ M for a 10 mm cell and 5 × 10⁻⁷-3 × 10⁻⁵ M for a 50 mm cell and a limit of detection at 3 × 10⁻⁷ M. The linear range of the SIA method was 6 × 10⁻⁶-5 × 10⁻⁴ M, with a detection limit of 2 × 10⁻⁶ M and a sample throughput of 15 h⁻¹. The proposed methods were successfully used for the determination of AsA in both pharmaceuticals and fruit juices, and the results were consistent with those provided by the 2,6-dichlorophenolindophenol method.     

Ultra-simple adaptor to convert batch cells with mercury drop electrodes in voltammetric detectors for flow analysis

A simple, robust and fast-responding flow adaptor for mercury drop electrodes (MDEs) is described. An L-shaped PTFE tube with an internal diameter of 0.5 mm is fixed with a silicone ring on the glass capillary of a MDE, in such a way as to direct the outcoming flow onto the mercury drop, from a distance of about 0.5 mm. Any commercial or laboratory-made batch cell, provided with an MDE, serves for the purpose. The level of supporting electrolyte in the cell is maintained constant through a siphon or a lateral draining orifice. The adaptor is compatible with all the different brands and operating modes of the MDEs (free dropping, controlled drop time, renewable static drop, hanging drop or sessile drop). Flow injection experiments were conducted with the following amperometric detection modes: sampled-DC, reverse pulse amperometry (RPA), and anodic stripping voltammetry (ASV). The FIA-RPA peaks presented a R.S.D.<0.8% for 1.0×10⁻⁵ mol l⁻¹ lead(II) (N=30, V_sample=100 μl). The response time (0-63% of the signal maximum) to a concentration step is 1.2 s for 500 μl injections of 0.1 mmol l⁻¹ ascorbic acid in acetate buffer at a flow rate of 1 ml min⁻¹, which corresponds to a response volume of 20 μl. As an example of practical application, copper(II) was determined in fertilizers by RPA using the standard addition method, at an analytical frequency of 90 injections per h.     

Development of a flow method for the determination of phosphate in estuarine and freshwaters—Comparison of flow cells in spectrophotometric sequential injection analysis

A sequential injection system with dual analytical line was developed and applied in the comparison of two different detection systems viz; a conventional spectrophotometer with a commercial flow cell, and a multi-reflective flow cell coupled with a photometric detector under the same experimental conditions. The study was based on the spectrophotometric determination of phosphate using the molybdenum-blue chemistry. The two alternative flow cells were compared in terms of their response to variation of sample salinity, susceptibility to interferences and to refractive index changes. The developed method was applied to the determination of phosphate in natural waters (estuarine, river, well and ground waters). The achieved detection limit (0.007 μM PO₄³⁻) is consistent with the requirement of the target water samples, and a wide quantification range (0.024–9.5 μM) was achieved using both detection systems.     

Determination of phosphate in hydroponic nutrient solutions using flow injection potentiometry and a cobalt-wire phosphate ion-selective electrode

The direct flow injection potentiometric (FIP) analysis of phosphate in hydroponic nutrient solution has been carried out using a cobalt-wire ion-selective electrode (ISE). Synthetic hydroponic nutrient solution, commercial hydroponic nutrient solution and working hydroponic farm nutrient solution were analysed for phosphate using the FIP technique. It is shown that FIP results compare favourably to standard methods of analysis such as spectrophotometry and indirect photometric ion-pair chromatography. Reproducible FIP response curves with a slope of −(47.57±0.03) mV per decade and intercept of −(169.7±0.1) mV were obtained for four separate calibrations in the concentration range 5.0×10⁻⁴–1.0×10⁻² M H₂PO₄⁻. Anion corrections for interferences by Cl⁻, NO₃⁻ and SO₄²⁻ were applied to all samples using the selectivity coefficients determined independently using a fixed interference method. Nevertheless, it was found that anion corrections were not necessary, as the deviations fell within the bounds of experimental error for the cobalt-wire ISE technique (i.e.±2–5% R.S.D.). The proposed FIP method enables the direct determination of phosphate in hydroponic nutrient solutions.     

Development of a flow injection method for monitoring cell membrane damage of wine lactic acid bacteria

A flow injection analysis (FIA) system was developed for the determination of phosphate efflux from wine lactic acid bacteria (Oenococus oeni and Lactobacillus hilgardii) as an indication of cell membrane damage. The system allowed the direct injection of the cell suspension, avoiding the filtration step, with minimum sample treatment and minimized reagent consumption. The developed system is characterized by a linear concentration zone between 3.23 × 10⁻⁵ and 4.84 × 10⁻⁴ mol L⁻¹ PO₄ ³⁻ and repeatability better than 2.9%. Bacterial suspensions were exposed to a chemical stress with phenolic acids and injected in the FIA system at regular intervals. The extracellular concentration of phosphate was measured spectrophotometrically. The experimental results obtained indicate that hydroxycinnamic acids (p-coumaric, ferulic and caffeic) induced faster phosphate leakage rates than hydroxybenzoic acids (vanillic and p-hydroxybenzoic) in both strains tested, which could be related to their higher lipophilic character.     

An automatic flow injection analysis procedure for photometric determination of ethanol in red wine without using a chromogenic reagent

An automatic reagentless photometric procedure for the determination of ethanol in red wine is described. The procedure was based on a falling drop system that was implemented by employing a flow injection analysis manifold. The detection system comprised an infrared LED and a phototransistor. The experimental arrangement was designed to ensure that the wine drop grew between these devices, thus causing a decrease in the intensity of the radiation beam coming from the LED. Since ethanol content affected the size of the wine drop this feature was exploited to develop an analytical procedure for the photometric determination of ethanol in red wine without using a chromogenic reagent. In an attempt to prove the usefulness of the proposed procedure, a set of red wines were analysed. No significant difference between our results and those obtained with a reference method was observed at the 95% confidence level. Other advantages of our method were a linear response ranging from 0.17 up to 5.14 mol L⁻¹ (1.0 up to 30.0%) ethanol (R=0.999); a limit of detection of 0.05 mol L⁻¹ (0.3%) ethanol; a relative standard deviation of 2.5% (n=10) using typical wine sample containing 2.14 mol L⁻¹ (12.5%) ethanol; and a sampling rate of 50 determinations per hour.     

Development of a tubular fluoride potentiometric detector for flow analysis: evaluation and analytical applications

In this work a construction procedure for tubular fluoride electrode to be used in flow systems is outlined. The electrode was constructed from a commercially available, LaF₃ single crystal. Principal advantages of the flow detector presented include simplicity of construction, robustness, durability, low cost and easy coupling into any point of a flow manifold.Evaluation of the intrinsic working characteristics of the potentiometric detector in a low dispersion manifold is presented with respect to analytical and dynamic parameters. The constructed detector has similar working characteristics to those of the conventional fluoride electrodes, namely the detection limit, lower limit of linear response and operational pH range.The analytical usefulness of the constructed device was assessed in a flow system developed for fluoride determination in toothpaste, tablet, collutory and water samples for which the reference procedures suggest the determination of fluoride ion with a conventional ion selective electrode.