Influence of the ionic liquid/gas surface on ionic liquid chemistry

Applications such as gas storage, gas separation, NP synthesis and supported ionic liquid phase catalysis depend upon the interaction of different species with the ionic liquid/gas surface. Consequently, these applications cannot proceed to the full extent of their potential without a profound understanding of the surface structure and properties. As a whole, this perspective contains more questions than answers, which demonstrates the current state of the field. Throughout this perspective, crucial questions are posed and a roadmap is proposed to answer these questions. A critical analysis is made of the field of ionic liquid/gas surface structure and properties, and a number of design rules are mined. The effects of ionic additives on the ionic liquid/gas surface structure are presented. A possible driving force for surface formation is discussed that has, to the best of my knowledge, not been postulated in the literature to date. This driving force suggests that for systems composed solely of ions, the rules for surface formation of dilute electrolytes do not apply. The interaction of neutral additives with the ionic liquid/gas surface is discussed. Particular attention is focussed upon H(2)O and CO(2), vital additives for many applications of ionic liquids. Correlations between ionic liquid/gas surface structure and properties, ionic liquid surfaces plus additives, and ionic liquid applications are given.     

Bromodimethylsulfonium bromide (BDMS) in ionic liquid: a mild and efficient catalyst for Beckmann rearrangement

Bromodimethylsulfonium bromide (BDMS)-catalyzed Beckmann rearrangement of a variety of ketoximes has been carried out in the imidazolium-based ionic liquid [bmim]PF₆ under mild conditions without using any additional cocatalyst or solvent to afford excellent conversion and selectivity. The ionic liquid is recovered and reused for up to three runs without any loss of efficiency.     

A green approach for efficient synthesis of N-substituted pyrroles in ionic liquid under microwave irradiation

A rapid synthesis of N-substituted pyrroles has been described by the reaction of 4-hydroxyproline with isatins in ionic liquid under microwave irradiation. The recovered ionic liquid was reused for six cycles. The reaction proceeds without the addition of any acid promoter     

Catalytic asymmetric hydrogenation in a room temperature ionic liquid using chiral Rh-complex of ionic liquid grafted 1,4-bisphosphine ligand

Introduction of imidazolium ionic liquid pattern to the catalyst not only avoided catalyst leaching but also increased the stability of catalyst in ionic liquid, and thus, the Rh-complex of 1,4-bisphosphine bearing two imidazolium salt moieties was successfully immobilized in an ionic liquid and reused several times for the hydrogenation of an enamide without significant loss of catalytic efficiency.     

A novel task-specific ionic liquid for Beckmann rearrangement: a simple and effective way for product separation

Under mild conditions and without any additional organic solvents, Beckmann rearrangement of ketoximes was performed in a novel task-specific ionic liquid consisting sulfonyl chloride. Especially for the conversion of cyclohexanone oxime to ε-caprolactam, ε-caprolactam has good solubility in water while the task-specific ionic liquid is immiscible with water, therefore, ε-caprolactam could be easily separated from the reaction system by water extraction.     

Palladium-catalyzed regiospecific aminocarbonylation of alkynes in the ionic liquid [bmim][Tf2N

[Structure: see text] Regiospecific construction of 2-substituted acrylamides was achieved by palladium-catalyzed aminocarbonylation of alkynes in the ionic liquid [bmim][Tf2N] without any acid additive under relatively mild conditions. The ionic liquid was used as the reaction medium and also acted as a promoter. Acrylamides were obtained in moderate to excellent yields, and an important feature is that the catalyst system can be recycled five times without loss of catalytic activity.     

Transparent,flexible and solid-state supercapacitors based on room temperature ionic liquid gel

This paper describes a novel strategy to make fully transparent, solid-state and flexible supercapacitors based on room temperature ionic liquid (RTIL) gel and ITO electrodes coated on transparent polymer substrate without a separator, which enables the roll-to-roll technique for fabrication of such supercapacitors as printable devices. This is the first type of transparent electrochemical double layer capacitor (EDLC) based on ionic liquid gel.     

Mono- and multi-layer adsorption of an ionic liquid on Au(110)

Ultraviolet photoelectron spectroscopy (UPS), work function measurements, low energy electron diffraction (LEED) and scanning tunnelling microscopy (STM) have been used to study the adsorption and desorption of 1-ethyl-3-methylimidazolium bis[(trifluoromethyl)sulfonyl]imide, [C(2)C(1)Im][Tf(2)N], on the (1×2) clean surface reconstruction of Au(110) in the temperature range 100-674 K. The ionic liquid adsorbed without decomposition, and desorbed without leaving any residue on the surface. For adsorption at room temperature a monolayer of strongly bound ionic liquid was formed with four interface states visible in UP spectra. STM at 100 K showed that the monolayer consisted of well-ordered rows of adsorbed ionic liquid aligned parallel to the close packed rows of surface gold atoms (the [110] direction) with a separation of ×2 (the same as the clean surface reconstruction) between the rows in the orthogonal [001] direction. Multilayer adsorption at room temperature occurred by droplet formation followed by smoothing of the droplets to a layered morphology with time. Heating caused multilayer desorption at temperatures in the 363-383 K range, followed by partial monolayer desorption at 548 K to produce a Au(110)-(1×3) reconstructed surface with sub-monolayer domains of ionic liquid. Desorption of the remaining ionic liquid at 600 K caused the gold surface to reconstruct back to the clean (1×2) reconstruction.     

Electrodeposition and stripping of zinc from an ionic liquid polymer gel electrolyte for rechargeable zinc-based batteries

In this paper, we report on zinc deposition and stripping in an ionic liquid polymer gel electrolyte on gold and copper substrates, respectively. The ionic liquid-based polymer gel electrolyte is prepared by combining the ionic liquid 1-butyl-1-methylpyrrolidinium trifluoromethylsulfonate ([Py_1,4]TfO), with Zn(TfO)₂ and poly(vinylidene fluoride-co-hexafluoropropylene) (PVdF-HFP). The ionic liquid polymer gel electrolyte exhibits good conductivity (2.2 mS cm^?1) and good mechanical stability. Zinc deposition and stripping in the ionic liquid polymer gel electrolyte were studied by cyclic voltammetry, potentiostatic, and galvanostatic cycling (charging/discharging) experiments. The gel electrolyte exhibits a promising electrochemical stability and allows a quasi-reversible zinc deposition/stripping. The morphology of the zinc deposits after 10 cycles of zinc deposition/stripping is compact and dense, and deposits without any dendrite formation can be obtained. The quasi-reversibility of the electrochemical deposition/stripping of zinc in this ionic liquid polymer gel electrolyte is of interest for rechargeable zinc-based batteries.     

Cyclotrimerization of an aliphatic aldehyde catalyzed by acidic ionic liquid

Without any additional organic solvent, the cyclotrimerization of aliphatic aldehyde could be catalyzed by acidic ionic liquid. Under optimum reaction conditions (298 K, 1 h, a molar ratio of 60:1 of isobutyraldehyde to ionic liquid), the conversion rate and selectivity for cyclotrimerization of isobutyraldehyde were 93.0 and 100%, respectively. The liquid product formed a separate phase that was decanted and the solid product could be separated by extraction. The ionic liquid could be easily reused after removal of water under vacuum.     

离子液体耦合有机过氧化物脱除二苯并噻吩的研究

以12-磷钨酸为催化剂,研究了离子液体耦合有机过氧化物脱除二苯并噻吩(DBT)。研究结果表明,单独使用离子[bmim]BF4、[bmim]PF6液体为萃取剂,脱硫率为27.78%~38.76%。以由等体积的H2O2与甲酸制成有机过氧化物为氧化剂,不使用催化剂和离子液体,温度70℃,反应时间6 h,DBT氧化为二苯并噻吩砜的比例为76.6%。在催化剂作用下,将离子液体与氧化剂耦合使用时,脱硫率明显提高。当催化剂与DBT的摩尔比为0.20∶1,氧化剂与DBT的体积比为10∶1,[bmim]PF6离子液体与DBT的体积比为1∶1,在70℃反应6 h后,脱硫率可达98.60%。耦合体系重复使用五次后,氧化脱硫活性没有明显降低。     

Selective extraction/isolation of hemoglobin with ionic liquid 1-butyl-3-trimethylsilylimidazolium hexafluorophosphate (BtmsimPF6)

Ionic liquid was for the first time employed for selective isolation of heme-protein species. Direct extraction of hemoglobin into ionic liquid without using any concomitant reagent or extractant was carried out. Hemoglobin at the level of 100 ng μL⁻¹ could readily be quantitatively extracted into ionic liquid (IL) 1-butyl-3-trimethylsilylimidazolium hexafluorophosphate (BtmsimPF₆) in the absence of any co-existing extractants/additives at pH 7, at the same time; however, the other protein species do not interfere and remain in the aqueous phase. A back extraction efficiency of ca. 80% for 20 ng μL⁻¹ hemoglobin in ionic liquid phase was achieved with sodium dodecyl sulfate (SDS) solution as stripping reagent. ⁵⁷Fe Mossbauer spectra and circular dichroism (CD) spectra indicated that the penta-coordinated ferrous atom in hemoglobin provide a vacant or free coordinating position, which could be occupied by the cationic Btmsim⁺ moiety. The interaction/coordination reaction between the iron atom in the heme group of hemoglobin and the cationic ionic liquid moiety furnishes the driving force for facilitating fast transfer of hemoglobin into BtmsimPF₆. The present system was applied for selective isolation of heme-protein, i.e., hemoglobin from human whole blood without any pretreatment, giving rise to satisfactory results.     

Catalysis by ionic liquid. A green protocol for the stereoselective debromination of vicinal-dibromides by [pmIm]BF4 under microwave irradiation

An easily accessible ionic liquid, 1-methyl-3-pentylimidazolium fluoroborate, [pmIm]BF4, has been demonstrated to be an efficient catalyst as well as reaction medium for the stereoselective debromination of a variety of structurally diverse vicinal-dibromides to the corresponding (E)-alkenes in high yields under microwave irradiation. This reaction does not require any organic solvent and any metal or any conventional reducing agent, and the ionic liquid is recycled without any appreciable loss of its catalytic efficiency.     

Aryl C-glycosylation using an ionic liquid containing a protic acid

Aryl C-glycosylation of several glycosyl donors, including unprotected sugars, with phenol and naphthol derivatives in an ionic liquid containing a protic acid proceeded effectively and stereoselectively to give the corresponding aryl C-glycosides in good to high yields. Because the ionic liquid was nonvolatile, the reaction could be carried out under reduced pressure; in addition, the ionic liquid could be reused without loss of effectiveness. These features contribute to the significant advantages of this novel aryl C-glycosylation reaction.     

Palladium nanoparticles supported onto ionic carbon nanotubes as robust recyclable catalysts in an ionic liquid

Palladium nanoparticles have been deposited onto imidazolium bromide-functionalized ionic MWCNTs through hydrogen reduction of Na2PdCl4 in water without aid of surfactants under extremely mild conditions, and combined with an ionic liquid to create a new recyclable ionic liquid-based catalytic system allowing up to 50 times recycling.     

Electrochemical synthesis and the functionalization of few layer graphene in ionic liquid and redox ionic liquid

Electrochemical reductive exfoliation of graphite to few layered graphene(FLG) in presence of 1-ethyl-2,3-dimethyl imidazolium bis(trifluoromethylsulfonyl) imide ionic liquid and redox ionic liquid based ferrocene has been investigated. Thus, by applying a mild negative potential(-2.7 V vs. Fc/Fc~+) to carbon electrode in ionic liquid graphene flakes could be generated. The generated materials have been characterized by X-ray photoelectron spectroscopy, Raman spectroscopy, high resolution transmission electron microscopy and atomic force microscopy. XPS and Raman analysis show that the electrochemical reductive exfoliation provides the formation of FLG. The thickness of the resulting FLG was found to be ranged between 4 and1 nm. HR-TEM images reveal the formation of few graphene layers and in some cases single graphene layer was observed.Moreover, this electrochemical route conduces to the formation of ionic liquid functionalized FLG. Finally, the reductive exfoliation was further investigated in the presence of redox ionic liquid. XPS and electrochemical measurements confirm the presence of ferrocene.     

Poly(basic ionic liquid) coated magnetic nanoparticles: High-loaded supported basic ionic liquid catalyst

A novel poly(ionic liquid) (PIL) coated magnetic nanoparticle was synthesized by distillation-precipitation-polymerization of 1-vinyl-3- ethyl imidazolium in the presence of surface modified magnetic nanoparticles. The resulting catalyst was used as magnetic heterogeneous base catalyst for the synthesis of 4H-benzo[b]pyrans in water. The separation of the catalyst from the reaction mixture was readily achieved by simple magnetic decantation and the catalyst could be easily recycled without appreciable loss of catalytic activity. Because of polymer layers coated the surface of the magnetic nanoparticles, the catalyst has a high loading level of ionic liquid.     

A solvent and transition metal-free,highly efficient Brønsted acidic ionic liquid promoted one-potthree-component reactions for the synthesis of tetrasubstituted pyrroles

Abstract

The present protocol describes a highly efficient, transition metal and solvent-free one-pot annulation of amines, dialkyl acetylenedicarboxylates and β-nitrostyrene using imidazolium Brønsted acidic ionic liquid for the synthesis of tetrasubstituted pyrroles. A diverse functionalized tetrasubstituted pyrroles derivatives were obtained with excellent yields under transition metal and solvent-free conditions. The Brønsted acidic ionic liquid can be easily recovered and reused for the next reaction without any effects on the yields of the products. This green protocol provides structurally complex, medicinally important tetrasubstituted pyrroles with various substitution patterns in a one-pot operation.     

Synthesis,characterization, and application of silica supported ionic liquid as catalyst for reductive amination of cyclohexanone with formic acid and triethyl amine as hydrogen source

A silica supported ionic liquid was synthesized and characterized by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy, X-ray diffraction, N2 adsorption-desorption, and thermogravimetric analysis. All these techniques, especially SEM results indicated the presence of well-defined spherical particles having diameters larger than the pristine silica particles, confirming the successful immobilization of the ionic liquid. The prepared silica supported ionic liquid was used in the reductive amination of cyclohexanone under different conditions with different azeo-tropic mixtures of formic acid and triethyl amine as a hydrogen source. The catalyst showed effi-cient catalytic performance and excellent yields of N-cyclohexyl amine derivatives in the range of 58%to 84%at 30 °C. After completion of the reaction, the catalyst was easily recovered by simple filtration and reused for another five cycles without any significant impact on product yields. The obtained catalytic performance indicates that the present catalyst is green, very active, and reusable for the reductive amination of cyclohexanone.     

Hydrotalcite catalysis in ionic liquid medium: a recyclable reaction system for heterogeneous Knoevenagel and nitroaldol condensation

Knoevenagel condensation proceeds efficiently in recyclable [bmim]PF₆ and [bmim]BF₄ without any catalyst, and hydrotalcites in ionic liquid serve as a safe and recyclable reaction system for both Knoevenagel as well as nitroaldol condensations.