Pd/C和Raney Ni催化剂的制备及其催化活性比较

制备了Pd/C和Raney Ni催化剂,其结构和性能经XRD,BET和SEM表征。并以呋喃加氢制备四氢呋喃为探针反应,对两种催化剂的催化活性进行了比较,探讨了反应温度、反应压力和催化剂用量对转化率和选择性的影响,结果表明:Raney Ni的催化活性优于Pd/C。     

甲烷在Ni/TiO2催化剂表面的活化

考察了Ni/TiO2催化剂甲烷部分氧化和二氧化碳重整制合成气的反应活性,实验表明,以TiO2为载体的镍系催化剂对于甲烷部分氧化制合成气反应具有较好的活性,尤其对H2的选择性较高,对二氧化碳重整制合成气反应具有较好的低温反应活性.采用脉冲-质谱在线分析等技术,在无气相氧条件下向Ni/TiO2催化剂脉冲CH4,发现甲烷在催化剂表面的活化（转化）及其氧化产物的选择性与金属催化剂表面氧的浓度密切相关.CH4与Ni/TiO2催化剂作用过程中存在明显的氢溢流和氧溢流现象,可能是这种溢流效应使得Ni/TiO2催化剂具有良好的反应活性和抗积碳性能.     

甲烷在Ni/TiO_2催化剂表面的活化

考察了Ｎｉ／ＴｉＯ２催化剂甲烷部分氧化和二氧化碳重整制合成气的反应活性,实验表明,以ＴｉＯ２为载体的镍系催化剂对于甲烷部分氧化制合成气反应具有较好的活性,尤其对Ｈ２的选择性较高,对二氧化碳重整制合成气反应具有较好的低温反应活性．采用脉冲－质谱在线分析等技术,在无气相氧条件下向Ｎｉ／ＴｉＯ２催化剂脉冲ＣＨ４,发现甲烷在催化剂表面的活化（转化）及其氧化产物的选择性与金属催化剂表面氧的浓度密切相关．ＣＨ４与Ｎｉ／ＴｉＯ２催化剂作用过程中存在明显的氢溢流和氧溢流现象,可能是这种溢流效应使得Ｎ／ＴｉＯ２催化剂具有良好的反应活性和抗积碳性能．     

Ni/ZrO2催化剂上甲烷水蒸气重整反应的研究

研究了Ni/ZrO2催化剂对甲烷水蒸气重整制合成气的反应性能。考察了催化剂的还原温度、载体焙烧温度以及反应温度、原料配比和空速等对催化剂性能的影响。利用XRD、TEM、XPS等手段对催化剂的织构形貌进行了表征。研究表明，Ni/ZrO2催化剂用于甲烷水蒸气重整制合成气不仅具有较高的活性，也具有较好的稳定性。水蒸气比增加，CH4转化率增大、CO选择性下降。CH4转化率及CO选择性均随空速增大而下降。使用10%Ni/ZrO2催化剂，在650 ℃、空速1.984×104 h－1、原料气配比H2O∶CH4∶N2=2∶1∶2.67的条件下，获得CH4转化率85%、CO选择性70%的结果。     

介孔Ni/MgO催化剂催化水蒸气重整生物质油制氢

采用水热法制备了介孔MgO作为催化剂的载体,并制备了介孔Ni/MgO催化剂。利用N_2吸附-脱附、XRD、H_2-TPR等对样品进行表征,并考察了介孔Ni/MgO催化水蒸气重整糠醛、生物质油模型物和两种商用生物质油制氢的活性。结果表明,在介孔Ni/MgO催化剂催化水蒸气重整糠醛制氢反应中,随着反应温度的提高,水蒸气重整糠醛中糠醛的转化率、氢气的产率和氢气的选择性,都呈现递增的趋势。在反应温度提高到600℃时,糠醛的转化率和氢气的产率分别达到94.9%和83.2%。Ni/MgO催化水蒸气重整二组分模拟生物质油,糠醛/乙酸、糠醛/羟基丙酮制氢的反应中,氢气的产率分别达到87.3%和86.8%,均高于水蒸气重整糠醛反应中氢气的产率。由此表明,乙酸或羟基丙酮的存在,提高了模拟生物质油中主要有机物组分糠醛的转化率,并相应地提高了氢气的产率。在水蒸气重整商用生物质油制氢反应中,随着反应物水碳比(S/C(molar ratio)=5、10、15、20、25)的提高,主要有机物的转化率、氢气的产率和选择性呈现出增加的趋势。在水碳比为20时,两种生物质油的主要有机物组分(糠醛、乙酸和羟基丙酮)的转化率均可达90%以上,氢气的产率也达到81.0%以上。由此可知,Ni催化剂对于水蒸气重整商用生物质油也具有较高的催化活性。     

木质素降解模型化合物愈创木酚及苯酚原位加氢制备环己醇

以Raney Ni为催化剂,研究了甲醇水相重整制氢与木质素降解模型化合物愈创木酚／苯酚加氢的耦合反应.考察了反应前冷压、反应温度、反应时间、物料配比等条件对木质素降解模型化合物原位加氢反应性能的影响,并对影响机制进行了讨论.结果表明,在反应温度为220 ℃、反应前冷压0 MPa(表压)、物料比水／甲醇／模型化合物为20∶5∶0.8的条件下,反应7 h后愈创木酚转化率与环己醇选择性分别达99.00％和93.74％,反应12 h后苯酚的转化率与环己醇选择性分别达90.50％和99.29％.采用原位加氢反应,木质素降解的酚类模型化合物转化率和选择性明显优于外部供氢反应的转化率和选择性,同时,避免了外部供氢反应存在的氢气制备、储存、传输及加氢条件苛刻等问题,为木质素解聚产物制备化工品提供了新思路与实验基础.     

Ni-Fe/蒙脱土催化剂催化乙醇水蒸气重整制氢的研究

采用浸渍法制备了一系列Ni-Fe/蒙脱土(MMT)催化剂,并应用于乙醇水蒸气重整制氢反应(ESR)。采用X射线衍射(XRD)、N_2吸附脱附分析和H_2-程序升温还原(H_2-TPR)表征手段对催化剂的物理化学性质、还原性能、碳沉积等进行了研究。结果表明,Ni-Fe/MMT催化剂中,Ni、Fe高度分散在载体MMT层间及表面,而且Fe的加入降低了Ni颗粒的粒径,增强了Ni~(2+)与载体的相互作用力。以10Ni5Fe/MMT为催化剂,在反应温度为500℃、水醇比为3∶1、空速为12 h~(-1),反应进行30 h后,乙醇转化率为100%,氢气选择性仍保持72%,副产物CO和CH_4含量明显降低。这是因为催化助剂Fe的引入,一方面,提高了Ni的分散度,使得ESR低温活性较好;另一方面,减小了Ni颗粒粒径,小颗粒的Ni有利于抑制甲烷的生成,并且Fe的加入加强了甲烷重整和水煤气变换反应,提高产物中氢气的选择性。     

Ni-B/SiO2非晶态催化剂应用于硝基苯液相加氢制苯胺

 考察了Ni－B／SiO2非晶态催化剂在高压液相硝基苯加氢制苯胺反应中的催化活性和选择性．研究表明,该催化剂不仅具有很高的催化活性,而且对苯胺的选择性较高,优于RaneyNi以及其它Ni基催化剂．晶化导致催化剂失活．载体的存在不仅能提高催化剂的分散度,而且能对非晶态结构起稳定化作用;将催化剂保存在乙醇中可保持其活性不变．结合催化剂的表征,讨论了Ni－B／SiO2非晶态催化剂的催化性能与其结构的关系．     

Cu/ZrO2催化剂上乙醇水蒸气重整反应的研究Ⅰ催化剂性能及其制备参数的影响

研究了Cu/ZrO2催化剂在乙醇水蒸气重整反应中的催化性能。用常规沉淀法、醇凝胶法制备了ZrO2载体;用浸渍法或共沉淀法制备了Cu/ZrO2催化剂。考察了ZrO2载体的制备方法以及Cu/ZrO2的制备参数对催化剂性能的影响。采用BET、XRD、TEM及XRF等方法对催化剂的比表面积、孔容、晶相、表面形貌以及活性组分等进行了表征。同时,制备并比较了Ni/ZrO2、Cu/10MgO-90ZrO2和Cu/10CaO-90ZrO2催化剂的性能,考察了活性组分Cu、Ni的差异以及ZrO2载体的影响。在Cu/ZrO2催化剂(Cu的质量分数为8%)上,500 ℃~600 ℃乙醇转化率达到98%~100％、H2选择性为2.0~2.6（摩尔比）。 Cu/ZrO2与Ni/ZrO2机械混合有助于H2选择性的提高。在催化剂载体中添加MgO、CaO碱性物质可以使H2选择性提高1.3倍~2.0倍。浸渍法制备的Cu/ZrO2催化剂的性能优于共沉淀法。     

Ni/TiO2-SiO2上光催化重整葡萄糖以低CO选择性制H2（英文）

Nano-sized Ni particles on TiO2-SiO2 were synthesized by the two methods of photo-assisted deposition(PAD) and impregnation.H2,which is a promising energy carrier,with a low CO concentration was produced by the photocatalytic reforming of glucose(a model biomass) on the Ni/TiO2-SiO2 catalyst.The supported Ni enhanced the rate of H2 production while it suppressed CO selectivity.The catalysts were characterized by X-ray diffraction,X-ray absorption fine structure,transmission electron microscope,and nitrogen adsorption analysis.Both H2 production and CO selectivity were strongly dependent on the preparation method,and PAD-Ni/TiO2-SiO2 was the better catalyst for H2 production with the lowest CO concentration.     

H_2 production with low CO selectivity from photocatalytic reforming of glucose on metal/TiO_2 catalysts

H2 with low CO concentration is produced via photocatalytic reforming of glucose (as a representative of biomass component) on metal/TiO2 catalyst (metals: Pt, Rh, Ru, Ir, Au, Ni, Cu). It is shown that the loaded metals generally enhance the rate of H2 production, while they depress the CO selectivity. Both H2 production and CO selectivity are strongly dependent on the kind of deposited metals on TiO2. For example, Rh/TiO2 catalyst is found to be most active for H2 production while with the most extremely low CO concentration from the photocatalytic reforming of glucose.     

Ni/TiO_2-SiO_2上光催化重整葡萄糖以低CO选择性制H_2(英文)

Nano-sized Ni particles on TiO2-SiO2 were synthesized by the two methods of photo-assisted deposition(PAD) and impregnation.H2,which is a promising energy carrier,with a low CO concentration was produced by the photocatalytic reforming of glucose(a model biomass) on the Ni/TiO2-SiO2 catalyst.The supported Ni enhanced the rate of H2 production while it suppressed CO selectivity.The catalysts were characterized by X-ray diffraction,X-ray absorption fine structure,transmission electron microscope,and nitrogen adsorption analysis.Both H2 production and CO selectivity were strongly dependent on the preparation method,and PAD-Ni/TiO2-SiO2 was the better catalyst for H2 production with the lowest CO concentration.     

Characterization and Catalytic Properties of a Rapidly Quenched Ni-RE-P-AL Catalyst

IntroductionAmorphous.alloy has been found to have superior catalytic properties["']. However, asan applied catalyst, its small surface area and low thermal stability during the catalytic processare the encountered problems usually.In the previous study, we found that addition of a small amount of rare earth element effectively stabilized the amorphous phase in a Ni--P alloyL'~'j, and the surface area of the amorphous Ni--RE--P alloy could be greatly enlarged by introducing Al into the Ni-…     

ZnO纳米线负载Pd1单原子催化剂催化若干反应性能的考察

将孤立的Pd原子分散到ZnO纳米线(NWs)上作为单原子催化剂(SACs),并考察了它们在若干反应中的催化性能.Pd1/ZnO SAC对甲醇蒸汽重整制氢反应表现出高的活性、稳定性和CO2选择性.该催化剂体系对CO和H2的氧化也具有高活性,但在富氢物料中CO优先氧化反应中的催化剂性能较差,这主要是由于在ZnO负载的Pd1原子上H2氧化的强竞争反应所致.常压下在Pd1/ZnO SAC上就可发生逆水汽变换反应.该系列催化反应测试结果清楚地表明,选择合适金属与载体对开发分子催化转化用单原子催化剂至关重要.     

还原剂对Au-Pd/CeO2催化剂甲醇部分氧化性能的影响

以PVP为保护剂,乙醇(ER)、乙二醇(GR)和水合肼(HR)为还原剂制备了一系列Au-Pd/CeO2催化剂,考察了还原剂对甲醇部分氧化性能的影响,并运用XRD、TPD和TPR等手段对催化剂进行了表征。结果表明,Au-Pd/CeO2(ER)催化剂具有较大的比表面积,形成的AuxPdy量较多、粒径较小、分散度较高、活性组分与载体的相互作用较强,同时对甲醇的吸附量较大和吸附温度较低。因此,该催化剂具有较高的催化活性和氢气选择性以及较低的CO质量分数。     

Development of a Ni–Pd/CeZrO<Subscript>2</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalyst for the effective conversion of methane into hydrogen-containing gas

The effects of the Pd content (0–1 wt %) and the synthesis method (joint impregnation with Ni + Pd and Pd/Ni or Ni/Pd sequential impregnation) on the physicochemical and catalytic properties of Ni–Pd/CeZrO₂/Al₂O₃ were studied in order to develop an efficient catalyst for the conversion of methane into hydrogen-containing gas. It was shown that variation in the palladium content and a change in the method used for the introduction of an active constituent into the support matrix make it possible to regulate the redox properties of nickel cations but do not affect the size of NiO particles (14.0 ± 0.5 nm) and the phase composition of the catalyst ((γ + δ)-Al₂O₃, CeZrO₂ solid solution, and NiO). It was established that the activity of Ni–Pd catalysts in the reaction of autothermal methane reforming depends on the method of synthesis and increases in the following order: Ni + Pd < Ni/Pd < Pd/Ni. It was found that, as the Pd content of the Ni–Pd/CeZrO₂/Al₂O₃ catalyst was decreased from 1 to 0.05 wt %, the ability for self-activation, high activity, and operational stability of the catalyst under the conditions of autothermal methane reforming remained unaffected: at 850°C, the yield of hydrogen was ~70% at a methane conversion of ~100% during a 24-h reaction.     

常压两步法催化丙三醇脱水-加氢制备 1,2-丙二醇

 在常压 H2 气氛下催化丙三醇脱水-加氢制备了 1,2-丙二醇. 首先在 220 oC 和常压 H2 条件下, 以 Cu/Al2O3 为催化剂催化丙三醇脱水生成中间体丙酮醇, 其选择性高达 86%. 考察了 Cu 负载量、反应温度和反应气氛对催化剂性能的影响. 在随后的丙酮醇加氢反应中, Raney Ni 催化剂显示出优异的催化性能, 在 120 oC 和常压 H2 条件下, 1,2-丙二醇选择性可达 99% 以上, 催化剂连续使用 5 h 未出现失活现象. 考察了反应温度、空速及反应时间对催化剂性能的影响.     

Ni-Fe/La2O2CO3催化乙醇水蒸气重整制氢的研究

采用La2(CO3)3空气焙烧法制备了La2O2CO3载体、采用浸渍法制备了Ni,Fe不同比例的Ni-Fe双金属催化剂及Ni/La2O2CO3,Fe/La2 O2 CO3催化剂,考察了各催化剂从300～700℃催化乙醇水蒸气重整反应的性能,并用BET,XRD,TPR等技术对催化剂进行表征。结果表明,相对单一金属催化剂,Ni-Fe双金属催化剂均表现出更高的活性,这可能是因为高分散的Ni,Fe和LaFeyNi1-yO3的共存作用。其中Ni含量为10%,Fe含量为5%时的Ni-Fe/La2O2CO3表现出最高的活性,400℃时乙醇的转化率为100%,H2的选择性最高达到94.1%,而CO的选择性则低至1.2%。     

水溶性钯膦络合物催化1-辛烯的氢羧基化反应

利用水溶性配体TPPTS与Pd（OAc）2在水相中催化1-辛烯的氢羧基化反应,能实现有机相产物与水相催化剂的清洁分离和催化剂的循环利用．分别考察了钯浓度、表面活性剂（CTAB）、酸助剂、反应时间、CO压力以及温度对该反应的影响．在H2O=16mL,C（Pd）=2．0mmol／L,C（TPTS）／c（Pd）=25,C（p...     

A MEMS methanol reformer heated by decomposition of hydrogen peroxide

This paper presents the design, fabrication and evaluation of a micro methanol reformer complete with a heat source. The micro system consists of the steam reforming reactor of methanol, the catalytic decomposition reactor of hydrogen peroxide, and a heat exchanger between the two reactors. In the present study, catalytic decomposition of hydrogen peroxide is used as a process to supply heat to the reforming reactor. The decomposition process of hydrogen peroxide produces water vapor and oxygen as a product that can be used efficiently to operate the reformer/PEMFC system. Cu/ZnO was selected as a catalyst for methanol steam reforming and Pt for the decomposition of hydrogen peroxide. Incipient wetness method was used to load catalysts on a porous support. Catalyst loaded supports were inserted in the cavity made on the glass wafer. The performance of the methanol steam reforming system was measured at various test conditions and the optimum operation condition was sought. At the optimum condition, the hydrogen selectivity was 86.4% and the thermal efficiency was 44.8%. The product gas included 74.1% H(2), 24.5% CO(2) and 1.4% CO and the total volume production rate was 23.5 ml min(-1). This amount of hydrogen can produce 1.5 W of power on a typical PEMFC.