Synthesis and application of water‐based urethane acrylate crosslinking agent containing unsaturated group

In this study, we synthesized 1,1,1‐trimethlyolpropane (TMP)‐based diol which has a pendant anionic group and a reactive double bond in the pendant cyclic ring. Then, a water‐based urethane acrylate crosslinking agent (CA) was prepared from isophrone diisocyanate (IPDI), 2‐hydroxyethyl acrylate (2‐HEA), and a low molecular weight diol bearing pendant carboxylic acid. The CA content was varied in order to investigate the influence of the added content on the mechanical and dynamic mechanical properties. The diol used in this study was TMP–cis‐1,2,3,6‐tetrahydrophthalic anhydride (TPA) which was synthesized from the esterification reaction of TMP with TPA. This diol was liquid at room temperature. As the CA increased, the initial modulus and elongation at break decreased. Also, increase of the rubbery plateau modulus was observed by dynamic mechanical analysis (DMA). This result was believed to result from an increase in the crosslinking density in the mixtures. Shift of the T_gh to a higher temperature was also observed by DMA. This is due to the increased hard segments and the phase separation. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 1216–1223, 2000     

Structure‐property relationship in polyurethane elastomers containing starch as a crosslinker

Polyurethane elastomers were synthesized using polypropylene glycol (PPG 2000) as the polyol and starch as the multifunctional crosslinker in varying concentrations. Thermal and mechanical properties were measured by DSC, DMA and tensile tests. The morphology was examined by SEM. The swelling behavior of the polyurethanes in various solvents was investigated and the solubility parameter was determined. All these properties were compared with those of polyurethanes containing 1,1,1 ‐trimethylol propane (TMP) as the crosslinker. Starch‐based polyurethanes exhibited better mechanical properties. The effect of varying the starch:TMP ratio on the mechanical strength was also studied. With increasing starch content, the tensile strength and elongation increased. The starch‐based PUs exhibited two glass transitions, whereas TMP‐based PUs exhibited one T_g. No significant difference in the T_gs of the two PUs was observed. The activation energy of St‐PU calculated from DMA was 69 kcal/mol. Soil degradation tests indicated greater biodegradability in polyurethanes containing starch than in those containing TMP.     

Properties and phase segregation of crosslinked PCL‐based polyurethanes

Polyurethane (PU) films were prepared from different types of poly(ε‐caprolactone) glycols and hexamethylene diisocyanate without using any other ingredients such as solvent, catalyst, or chain extender. Polymers were stabilized by crosslinking formed as allophanate and/or biuret linkages during the curing process. The effects of different components on the product properties such as chemical structure, microphase segregation, mechanical strength, thermo‐mechanical, thermal properties, and surface hydrophilicities were investigated by FTIR‐ATR, atomic force microscope, mechanical tester, dynamic mechanical analyses, thermogravimetric analyzer, differential scanning calorimetry, and contact angle measurements. Phase separation of hard and soft segments significantly varied depending on the type and molecular weight of diol and triol. Films containing urethane‐urea bonds displayed the maximum phase separation and the highest mechanical strength. Polyols having higher molecular weight increased hydrophilicity while urea bonds caused a reverse effect resulted by bidentate hydrogen bonds. Results showed PUs with various properties can be synthesized via environmentally friendly process without using any solvent or catalyst. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39758.     

Synthesis and characterization of biodegradable poly(ester‐urethanes) based on bacterial poly(R‐3‐hydroxybutyrate)

A series of poly(R‐3‐hydroxybutyrate)/poly(ε‐caprolactone)/1,6‐hexamethylene diisocyanate‐segmented poly(ester‐urethanes), having different compositions and different block lengths, were synthesized by one‐step solution polymerization. The molecular weight of poly(R‐3‐hydroxybutyrate)‐diol, PHB‐diol, hard segments was in the range of 2100–4400 and poly(ε‐caprolactone)‐diol, PCL‐diol, soft segments in the range of 1080–5800. The materials obtained were investigated by using differential scanning calorimetry, wide angle X‐ray diffraction and mechanical measurements. All poly(ester‐urethanes) investigated were semicrystalline with T_m varying within 126–148°C. DSC results showed that T_g are shifted to higher temperature with increasing content of PHB hard segments and decreasing molecular weight of PCL soft segments. This indicates partial compatibility of the two phases. In poly(ester‐urethanes) made from PCL soft segments of molecular weight (M_n ≥ 2200), a PCL crystalline phase, in addition to the PHB crystalline phase, was observed. As for the mechanical tensile properties of poly(ester‐urethane) cast films, it was found that the ultimate strength and the elongation at the breakpoint decrease with increasing PHB hard segment content. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 703–718, 2002     

Rheological and thermal properties of glycidyl azide polyol‐based energetic thermoplastic polyurethane elastomers

The purpose of this study was to investigate the effects of polyol on glycidyl azide polyol (GAP)‐based energetic thermoplastic polyurethane elastomers (ETPEs). Briefly, a series of GAP/polyol‐based ETPEs (GAP/polyol ETPEs) with different copolyol ratios and hard segment contents were synthesized using GAP‐diol with common polyol and 4,4‐methylenebis(phenylisocyanate)‐extended 1,5‐pentanediol as soft and hard segments, respectively, by solution polymerization in dimethylformamide. The three types of polyols used were poly(tetramethylene ether) glycol (PTMG), polycarbonate‐diol (PCL‐diol) and polycaprolactone‐diol (PCD‐diol). The synthesized GAP/polyol ETPEs were identified and characterized using Fourier transform infrared and ¹H NMR spectroscopy, differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA) and rheometric mechanical spectrometry. For GAP/PCL ETPEs with lower hard segment content, DSC results showed that the GAP segment failed to interact with either the PCL segment or PCL melting. In addition, the results of DMA showed that the presence of PCL segments in ETPEs improved the storage modulus below the melting temperature of the PCL block. Further, the crystalline PCL segments were attributed to reinforcing the ETPEs in a manner similar to that of the hard domain. As the hard segment content increased in the GAP/polyol ETPEs, both GAP/PTMG ETPEs and GAP/PCL ETPEs exhibited microphase separation transitions, while rheological experiments demonstrated a sudden decrease in complex viscosity in neighboring microphase separation transitions. © 2012 Society of Chemical Industry     

Synthesis and characterization of chlorine‐containing flame‐retardant polyurethane nanocomposites via in situ polymerization

We have developed flame‐retardant polyurethanes (FRPUs) and polyurethane (PU) nanocomposites via in situ polymerization. Three series of thermoplastic elastomeric PUs were synthesized to investigate the effect of incorporating 3‐chloro‐1,2‐propanediol (CPD) and nanoclay on mechanical, thermal properties, and also resistance to burning. PU soft segments were based on poly(propylene glycol). Hard segments were based on either CPD or 1,4‐buthane diol (BDO) in combination with methyl phenyl di‐isocyanate named PU or FRPU, respectively. In the third series, CPD was used as chain extender also nanoclay (1% wt) and incorporated and named as flame‐retardant polyurethane nanocomposites (FRPUN). Mechanical properties and LOI of PUs and nanocomposites have been evaluated. Results showed that increasing the hard segment (chlorine content) leads to the increase in flame retardancy and burning time. Addition of nanoclay to CPD‐containing PUs leads to obtain self‐extinguish PUs using lower CPD contents, higher Young's modulus, and strength without any noticeable decrease in elongation at break. Investigation of the TGA results showed that copresence of nanoclay and chlorine structure in the PU backbone can change thermal degradation pattern and improve nanocomposite thermal stability. X‐ray diffraction and transmission electron microscopy studies confirmed that exfoliation and intercalation have been well done. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Diffusion and sorption of benzene vapor through polybutadiene‐, polybutadiene/styrene‐, and polybutadiene/acrylonitrile‐based polyurethanes

A series of polyurethane (PU) films made from toluene diisocyanate (TDI), 1,4‐butanediol (BDO), and hydroxyl‐terminated polybutadiene (HTPB), hydroxyl terminated polybutadiene/styrene (HTBS), or hydroxyl terminated polybutadiene/acrylonitrile (HTBN) was synthesized by solution polymerization. The absorption of benzene vapor was found mainly in the soft phase. The equilibrium adsorption (M_∞) was reduced with increasing hard segment content for all the PUs. The values of M_∞ were in the sequence of HTBN‐PUs > HTBS‐PUs > HTPB‐PUs, which could be explained by the different interaction parameters between soft segments and benzene. The HTBN‐PU film showed the lowest degree of phase segregation and had more hard segments intermixed in the soft phase, restricting the movement of soft segments, and therefore resulted to non‐Fickian behavior, while the HTPB‐PU is antithetical. FTIR and atomic force microscopy were utilized to identify the hydrogen bonding behavior and morphology change of the PU films before and after the absorption of benzene vapor. The tensile strength of the HTBN‐PUs showed a greater decrease than that of HTBS‐PUs and HTPB‐PUs after absorbing benzene vapor. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2984–2991, 2004     

Aliphatic polycarbonate‐based polyurethane elastomers and nanocomposites. II. Mechanical,thermal, and gas transport properties

Thermal, thermomechanical, tensile and gas transport properties of aliphatic polycarbonate‐based polyurethanes (PC‐PUs) and their nanocomposites with bentonite for organic systems were studied. Hard segments are formed from hexamethylene diisocyanate and butane‐1,4‐diol. All PC‐PUs and their nanocomposites feature high degree of the phase separation. Three phase transitions were detected by temperature‐modulated differential scanning calorimetry (TMDSC) and dynamic mechanical thermal analysis. TMDSC revealed the filler affinity both to soft and hard segments, even though the affinity to hard segments is much stronger. Elongation‐at‐break at ambient temperatures is mostly over 700%, which leads together with high tensile strength (in some cases) to very high toughness values (over 200 mJ/mm³). The addition of 1 wt % of bentonite does not practically affect mechanical properties implying its very good incorporation into the PU matrix. Permeabilities and other gas transport properties depend on regularity of PC‐diol and on hard segment content, but the variations are insignificant. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Effect of microphase‐separation promoters on the shape‐memory behavior of polyurethane

A series of segmented polyurethanes (PUs) with novel thermosensitive shape‐memory behavior were synthesized via the in situ addition of a small amount of 1‐octadecanol (ODO) to a PU system. For comparison, liquid paraffin (LP) modified PUs were also synthesized. The effects of a small amount of ODO or LP on the PU suprastructure and the thermosensitive shape‐memory properties were studied with X‐ray diffraction, differential scanning calorimetry, dynamic mechanical analysis, and shape‐memory studies. The results indicated that the in situ addition of a small amount of ODO (e.g., 0.3 wt %) remarkably promoted microphase separation, facilitating the ordered packing of soft segments and the formation of perfect hard‐segment domains and thus significantly improving the shape‐memory properties. In contrast, LP had less significant influence on the shape‐memory behavior because of the macrophase separation of these nonpolar alkyl chains from the PU system. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:5224–5231, 2006     

Synthesis of CNT‐polyurethane nanocomposites using ester‐based polyols with different molecular structure: Mechanical,thermal, and electrical properties

Polyurethanes (PUs) were prepared by in situ polymerization of three diisocyanate with three synthesized low cost ester‐based polyols. The effect of diisocyanate type, diol structure, and molar ratio of diisocyanate to polyol on the mechanical properties was examined and the optimum chemical structure was introduced regarding the superior mechanical properties. Also, in presence of well dispersed hydroxylated multiwalled carbon nanotubes (CNT), PU/CNT nanocomposites were synthesized and fully characterized. The results showed that PU synthesized based on 1,4‐butane diol (BDO) has the best mechanical properties and thermal stability. Also, the PU samples synthesized from 1,6‐hexamethylene diisocyanate (HDI) were more profitable than aromatic diisocyanate structures due to higher crystallinity and microstructure packing. The nanocomposite sample containing 1.5% CNT was the optimum composition for the maximum tensile strength and electrical conductivity. This result was related to the uniform dispersion and bonding of CNTs to PU chains at this composition, while aggregates were formed at higher concentration of CNTs which increased the defects and reduced the uniformity of the structure. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44567.     

Thermal and mechanical properties of multiple‐component aliphatic degradable polyurethanes

Macroscopic thermal and mechanical properties of complex aliphatic polycarbonate‐based polyurethane (PU) films containing degradable ester units in PU backbone were studied by a combination of several experimental techniques. Differential scanning calorimetry (DSC) revealed that the synthesized oligomeric diol (DL‐L) contributes (in addition to polycarbonate diol) to the formation of soft‐segment domains, while the hard‐segment domains are formed from 1,6‐diisocyanatohexane (HDI) and butane‐1,4‐diol (BD). Three main phase transitions were detected by DSC and by dynamic mechanical thermal analysis. Thermogravimetric analysis (TGA) of two‐component PUs showed that the PU made from DL‐L and HDI is the least thermostable product, while the PU made from polycarbonate diol and HDI is the most stable one. The differences in the thermal stability of different four‐component PUs are not important. Tensile properties very sensitively reflect the changes in composition and in microstructure of PU samples; the best tensile properties exhibits the degradable sample containing the equimolar ratio of hydroxyl groups of macrodiol, oligomeric diol DL‐L and butane‐1,4‐diol. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41872.     

Polytriazoles based on alkyne terminated polybutadiene with and without urethane segments: Morphology and properties

Alkyne terminated polybutadiene with urethane segments (PUPB), a well‐controlled macromolecule, is synthesized with a two‐step routine and characterized by ¹H NMR, IR spectroscopy as well as gel permeation chromatograph. Alkyne terminated polybutadiene without urethane segments (PTPB) is also synthesized and characterized. The two alkyne terminated polybutadiene are cured to generate corresponding polytriazoles. It is found that the mechanical properties of PUPB based polytriazoles are superior to that of PTPB. The fractured surfaces of PTPB based polytriazoles exhibit smooth microstructures whereas PUPB based polytriazoles show the rough microstructures. The atomic force microscopy images reveal well‐established microphase‐separated morphology in polytriazoles with the promotion of urethane segments. Thus, the strong hydrogen bonding interaction existed in urethane has a remarkable effect on the morphology and then the mechanical properties of the as‐prepared polytriazoles. In addition, dioctyl sebacate can serve as an excellent plasticizer to PUPB based polytriazoles, lowering the glass transition temperature (T_g) and improving the ductility. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45178.     

Relationship between carbon dioxide transport,free volume and morphology of polyolefin‐based polyurethanes

A series of polyurethane (PU) films, produced from toluene diisocyanate, 1,4‐butane diol and either hydroxyl‐terminated polybutadiene (HTPB), hydroxyl‐terminated polybutadiene/acrylonitrile (HTBN) or hydroxyl‐terminated polybutadiene/styrene (HTBS), was synthesized by solution polymerization. Differential scanning calorimetry (DSC), Fourier‐transform infrared (FT‐IR) spectroscopy, and positron annihilation lifetime (PAL) spectroscopy were used to investigate the morphologies and free volumes of these polyolefin‐based polyurethanes. The free volumes were closely related to the morphologies of such PUs. HTBN‐based PUs showed the lowest degree of phase separation, the smallest fraction of free volume and smallest hole radius among the three types of polyolefin‐based PUs, while the HTPB‐based PUs displaying the largest values. The diffusion and permeation coefficients decreased with decreasing degree of phase separation and increasing content of hard segments. The transport data were in relation to the free volume and fitted the Fujita free‐volume model. Copyright © 2004 Society of Chemical Industry     

Effects of hard-segment compositions on properties of polyurethane–nitrolignin films

Segmented polyurethane (PU) films from castor-oil-based PU prepolymer with different hard-segment compositions and nitrolignin (NL) were synthesized. Diisocyanates (DIs), such as 2,4-tolylene DI (TDI) and 4,4′-diphenylmethane DI (MDI), 1,4-butanediol (BDO) as a chain extender, and trimethanol propane (TMP) as a crosslinker were used to obtain PU films containing NL (UL) which were named as UL–TB for TDI and BDO, UL–TT for TDI and TMP, UL–MB for MDI and BDO, and UL–MT for MDI and TMP, respectively. The mechanical properties and thermal stability of the films were characterized by a tensile test and thermogravimetric analysis, respectively. The MDI-based UL films exhibited a higher tensile strength (σ_b) and thermal stability than TDI-based UL. However, the recoverability of the TDI-based UL films was better than that of others. The UL films with TMP (UL–TT and UL–MT) had higher σ_b and lower breaking elongation (ϵ_b) than the UL films with BDO (UL–TB and UL–MB), caused by enhancement in the crosslinking network of hard segments and microphase separation between soft and hard segments. The values of σ_b and ϵ_b of the UL films that contained NL were much higher than those of the PU films, which indicates that the introduction of NL increased the interaction between hard segments by crosslinking. The hydrogen bonding in the UL films was studied by infrared spectroscopy, which indicated that MDI favored the formation of hydrogen bonds, especially in the ordered domain. Differential scanning calorimetry, dynamic mechanical analysis, and wide-angle X-ray diffraction indicated that the UL films were compatible as a whole, but microphase separation existed between soft and hard segments and significantly affected the mechanical properties. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 3251–3259, 2001     

Multiscale approach to the morphology,structure, and segmental dynamics of complex degradable aliphatic polyurethanes

A multiscale approach spanning from the segmental (subnanometer) up to micrometer level was applied for detailed study of the self‐assembly of aliphatic block polyurethane (PU) elastomers. To understand the principles of the self‐organization of hard and soft segments in the complex multi‐component systems, several two‐component model PU samples, that is, the products of 1,6‐diisocyanatohexane (HDI) with three diols differing in the length and constitution were also prepared, characterized, and investigated: (i) polycarbonate‐based macrodiol (MD), (ii) biodegradable oligomeric diol (DL‐L; product of butane‐1,4‐diol and D,L‐lactide), and (iii) butane‐1,4‐diol (BD). The study (particularly ¹³C‐¹H PILGRIM NMR spectra) reveals complex internal organization and interesting (application appealing) behavior of multi‐component PUs. Hard segments (HDI+BD products) feature self‐assembled and significantly folded chain conformations with interdomain spacing 15–22 nm (small‐angle X‐ray scattering analysis). The small domains are hierarchically assembled in various structural formations of µm size (spherulites) depending on PU composition, as detected by transmission electron microscopy and atomic force microscopy. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41590.     

Synthesis and characterization of permanently antistatic polyurethanes containing ionic liquids

An in situ embed ionic liquid method is designed and employed in thermoplastic polyurethanes (PUs). Unlike the traditional physically incorporated antistatic polymers where conductive fillers do not firmly combined with the matrix. This permanently antistatic PUs are successfully synthesized by using a novel polyester diol bonded with ionic liquids (ILs), which are obtained by an esterification. The ILs and novel polyester polyol are successfully synthesized and subsequently characterized by Fourier transform infrared spectroscopy (FTIR) and nuclear magnetic resonance spectrum (¹H NMR), respectively. The effects of ILs content, temperature, and relative humidity (RH) on the surface resistivity of PUs are studied by surface resistivity tests. It is found that the surface resistivity of PUs dramatically decreases with the increment of ILs and are insensitive to surrounding environment. The surface resistivity of PUs with 5.96 wt% ILs reaches 10¹⁰ Ω cm^?2 order of magnitude. The crystalline properties, thermal decomposition behaviors and mechanical properties of synthesized PUs are investigated by X‐ray diffraction (XRD), thermal gravimetric analysis (TGA) and tensile test respectively. The crystallinity of PUs with ILs is lower than that of pure PUs. Moreover, we also investigate the effect of ILs on the surface morphology of the PUs. POLYM. ENG. SCI., 56:629–635, 2016. © 2016 Society of Plastics Engineers     

Effect of chain extender on microphase structure and performance of self-healing polyurethane and poly(urethane-urea)

In this work, four aliphatic chain extenders, hexanediol (HDO), hexane diamine (HDA), cystamine (CY), and cystine dimethyl ester (CDE), were chosen to synthesize four kinds of polyurethane and poly(urethane-urea)s (PUs), respectively. HDO extended polyurethanes, HDA extended poly(urethane-urea), CY extended poly(urethane-urea), and CDE extended poly(urethane-urea) were denoted as OPU, APU, CPU, and SPU, respectively. The effect of chain extender type on microphase structure and performance of four PUs was investigated. Our research showed that mechanical strength increased in the following order: OPU < SPU < CPU < APU, and self-healing performance increased in the opposite direction. This result is attributed to the increasing degree of microphase separation: OPU < SPU < CPU < APU. The optimal sample SPU has not only excellent mechanical properties (tensile strength of 27.1 MPa and elongation at break of 397.7%), but also exhibits superior self-healing performance (self-healing efficiencies of 95.3% and 93.5% based on tensile strength and elongation at break). The moderate degree of microphase separation between the soft segments and the hard segments, the introduction of disulfide bonds and low degree of hydrogen bonding are responsible for preparing a polyurethane or poly(urethane-urea) system with high mechanical strength and excellent self-healing performance simultaneously. This work provides useful information for us to develop self-healing polyurethane or poly(urethane-urea) materials in the future.     

Synthesis,characterization of novel dihydrazide containing polyurethanes based on N1,N2‐bis[(4‐hydroxyphenyl)methylene]ethanedihydrazide and various diisocyanates

Four novel types of polyurethanes (PUs) were prepared from N¹,N²‐bis[(4‐hydroxyphenyl)methylene]ethanedihydrazide with two aromatic diisocyanates (4,4′‐diphenylmethane diisocyanate and tolylene 2,4‐diisocyanate) and two aliphatic diisocyanates (isophorone diisocyanate and hexamethylene diisocyanate). The chemical structure of both diol and PUs was confirmed by UV–vis, fluoroscence, FTIR, ¹H NMR, and ¹³C NMR spectral data. DSC data show that PUs have multiple endotherm peak. X‐ray diffraction revealed that the PUs contained semicrystalline and amorphous regions that varied with the nature of the backbone structures. PUs were soluble in polar aprotic solvents. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Composition,preparation procedure and physical properties of linear homogeneous polyurethanes for membranes

Linear polyurethanes (PUs) were prepared in solution in two steps. In the first step, toluene‐diisocyanate (TDI) 80:20 (T) was reacted with a short‐chain poly(oxypropylene) diol (V) to obtain prepolymers characterized by various ratios of R = [T]°/[V]°. In the second step, the prepolymers were reacted with the extender 1,4‐cyclohexanedimethanol (E) with various extension ratios R_E = (R ? 1)[V]°/[E]°. The PU properties were analyzed by various techniques. In particular, the molecular weights determined by gel permeation chromatography (GPC), the thermal properties such as glass transition temperature T_g and specific heat variation ΔC_p measured by differential scanning calorimetry (DSC), the chemical composition of the PUs and the various types of hydrogen bonds present in the polymers evidenced by Fourier‐transform infrared (FTIR) spectroscopy, the monophasic structure evidenced by small‐angle X‐ray scattering (SAXS), and the existence of only one T_g confirmed that these PUs were linear, amorphous and monophasic. Positron annihilation lifetime spectroscopy (PALS) analysis showed that the mean volume of the nanoholes increased with increasing temperature, but was not dependent on the composition, as expected for a monophasic system. A stoichiometric semi‐empirical model was proposed that relates the PU blocks' micro‐composition to the R and R_E macro‐parameters, chosen for the synthesis. The polymer assumes various expressions of the general formula X? [(TV)_k? (TE)_n]_m? X for different values of the R and R_E ratios. The micro‐parameters k and m have a direct connection with the experimental mean molecular weights of the prepolymer and the polymer, respectively: n depends only on R. The model could foresee the density of hydrogen bonds and distinguished the bonds connected to either V or E, which could be shown by FTIR analysis. This paper shows that, when using stereo‐irregular diols and blends of 2,4‐ and 2,6‐TDI, non‐stereoregular PUs are obtained. If low‐molecular‐weight diols are used and R < 3.3, it is quite improbable that the PU blocks separate into macrophases and therefore monophasic amorphous PUs are obtained. Monophasic PUs can be useful for applications such as in the field of membrane gas and vapour separation. Copyright © 2005 Society of Chemical Industry     

Use of short isobornyl methacrylate building blocks to improve the heat and oil resistance of thermoplastic elastomers via RAFT emulsion polymerization

Triblock copolymer (TCP)‐based thermoplastic elastomers (TPEs) were designed via reversible addition–fragmentation chain‐transfer emulsion polymerization. Short isobornyl methacrylate (IM) building blocks in the two ends of molecular chain were incorporated to guarantee the mechanical properties of the TPEs at high temperature (i.e., heat resistance) because of the high glass‐transition temperature (T_g) of poly(isobornyl methacrylate) (PIM; ～180 °C). The microphase separation, tensile properties at different temperatures, dynamic mechanical properties, oil resistance, and thermal stability of the TPEs were extensively characterized. The TPEs had distinct microphase separation with a wide inter‐T_g interval (150–185 °C). The tensile strength and elongation at break of the TPEs decreased with increasing temperature from 25 to 100 °C because of the reduced interactions in the phase domain. Even so, the TPEs had a high elongation at break beyond 200% and little change in the tensile strength even at 100 °C together with a wide quasi‐platform stage between the T_g values in dynamic mechanical analysis; this indicated good heat resistance. Meanwhile, the TPEs had an enhanced oil resistance and a thermal stability higher than 300 °C. These TCP‐based TPEs with heat and oil resistance broaden the application potential in practical fields. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45379.