YBa2Cu3O7-δ/La0.6Pb0.4MnO3多层膜的制备及激光感生热电电压效应的研究

采用脉冲激光沉积法在倾斜LaAlO3(100)衬底上制备了(YBa2Cu3O7-δ/La0.6Pb0.4MnO)L(L为多层膜周期数)外延多层膜.X射线衍射谱显示(YBCO/LPMO)L多层膜沿c轴生长.观察到多层膜中有很大的激光感生热电电压(LITV)出现,与YBa2Cu3O7-δ(YBCO)和La0.6Pb0.4MnO3(LPMO)单层膜相比,多层膜的LITV信号有约一个数量级的增强.讨论了影响(YBCO/LPMO)L多层膜的LITV效应的因素.     

Y_2O_3缓冲层对YBCO超导转变温度的影响（英文）

超导薄膜所受的应力对其临界转变温度Tc具有重要的影响,研究应力对超导薄膜Tc的影响对获得更高Tc材料具有重要意义.本文采用溶胶-凝胶法,在LAO单晶基板上制备了Y2O3/YBCO薄膜,并研究了Y2O3缓冲层对不同厚度YBCO超导薄膜的临界转变温度的影响.研究发现,当YBCO薄膜厚度为90nm时,由于Y2O3和YBCO薄膜的晶格错配,在YBCO/Y2O3薄膜的a-b面内引入了压应力,增加了c轴的晶格常数,结果提高了YBCO薄膜的临界转变温度.当YBCO薄膜的厚度较大时(如230nm),由晶格错配引起的应力通过位错的形式得以释放,YBCO薄膜的Tc变化不大.     

前驱液成分对TFA-MOD法制备YBa2Cu3O7-x薄膜超导性能的影响

采用三氟乙酸盐-金属有机沉积法(TFA-MOD)在铝酸镧单晶基体上制备了YBa₂Cu₃O_7-x (YBCO)超导薄膜.通过改变前驱液的成分,研究了金属元素的不同化学计量比对YBCO薄膜的结构和性能的影响.结果表明,按照钇盐Y(CH₃COO)₃与钡盐Ba(CH₃COO)₂的比例为Y ∶Ba=1 ∶1.5时所制备的YBCO薄膜的临界电流密度比严 关键词： 三氟乙酸盐-金属有机沉积 钇钡铜氧薄膜 前驱液成分 磁通钉扎     

YBa2 Cu3 O7-δ/SrNb0.01 Ti0.99 O3 p-n结的制备及其特性

采用脉冲激光沉积技术,在n型SrNb0.01Ti0.99O3(SNTO)单晶基片上生长p型YBa2Cu3O7-δ(YBCO)薄膜,制备出YBCO/SNTO p-n结.YBCO薄膜是高度c轴织构的超导薄膜,且具有良好的超导电性.YBCO/SNTO p-n结具有较好的整流特性和很好的温度与磁场稳定性.     

YBa2Cu3O7－δ/SrNb0.01Ti0.99O3 p-n结的制备及其特性

采用脉冲激光沉积技术，在n型SrNb001Ti099O3(SNTO)单晶基片上生长p型YBa2Cu3O7-δ(YBCO)薄膜，制备出YBCO/SNTO p n结.YBCO薄膜是高度c轴织构的超导薄膜，且具有良好的超导电性.YBCO/SNTO p n结具有较好的整流特性和很好的温度与磁场稳定性. 关键词： YBa2Cu3O7-δ SrNb001Ti099O3 p n结     

YBa2Cu3O7-δ/LaAlO3和Tl2Ba2CaCu2O8/LaAlO3高温超导薄膜内的应变对其微波表面电阻影响的研究

YBa2Cu3O7-δ/LaAlO3 (YBCO/LAO) 超导薄膜是通过热蒸发沉积方法制备的,实验中使用的Tl2Ba2CaCu2O8/LaAlO3 (TBCCO/LAO) 超导薄膜是通过直流磁控溅射方法制备的.通过分析两片超导薄膜的XRD谱计算出了两片超导薄膜内的应变,ΔCY=4.8483×10-3;ΔCT=8.5272×10-5,结果显示YBCO超导薄膜内的应变要大于TBCCO超导薄膜内的应变.另外,采用共面谐振技术研究这两片超导薄膜内的微波表面电阻随温度的变化,结果表明YBCO超导薄膜具有更大的微波表面电阻.分析和讨论了应变对超导薄膜微波表面电阻的影响.     

掺杂Y2O3和BaCeO3提高MOD-YBCO超导性能的研究

本文通过在前驱液中添加过量钇盐和铈的有机盐,采用三氟乙酸盐-金属有机沉积法(TFA-MOD) 在铝酸镧单晶基体上制备了含有纳米氧化钇和纳米铈酸钡的YBCO薄膜. 与纯YBCO薄膜相比,掺杂Y₂O₃/BaCeO₃的YBCO膜的临界转变温度几乎保持不变,为91 K左右. 而掺杂Y₂O₃/BaCeO₃的YBCO膜的临界电流密度达到5.0 MA/cm² (77 K, 0T), 是纯YBCO膜临界电流密度的1.5倍.薄膜中的Y₂O₃和BaCeO₃可能在YBCO内部起到了 有效的钉扎磁通作用. 关键词： 钇钡铜氧薄膜 2O₃和纳米BaCeO₃')" href="#">纳米Y₂O₃和纳米BaCeO₃ 磁通钉扎 三氟乙酸盐-金属有机沉积     

快速前处理TFA-MOD制备YBCO超导薄膜的研究

三氟乙酸盐金属有机物沉积(TFA-MOD)方法是制备YBa2Cu3O7(YBCO)超导薄膜最有应用前景的方法之一。采用快速前处理TFA-MOD的方法在LaAlO3单晶基片上生长YBCO薄膜并与常规的TFA-MOD方法进行对比研究。XRD分析表明用快速前处理TFA-MOD方法制备的YBCO薄膜的c轴取向一致性,没有常规的TFA-MOD制备的YBCO薄膜好。SEM的分析表明快速前处理TFA-MOD制备的YBCO超导薄膜表面有孔洞和YBCO(103)取向生长的晶粒,常规方法制备的YBCO薄膜表面比较光滑,孔洞较少。虽然较常规方法制备的薄膜的临界电流密度(JC)低,但超导电性能分析表明,快速前处理方法制备的YBCO薄膜JC达到1mA/cm2以上,且前处理时间大幅缩短,对于提高YBCO薄膜制备的效率非常有效。     

湿度对YBCO薄膜微观结构和超导性能的影响

文中采用无氟高分子辅助金属有机物沉积法( PA - MOD)在不同湿度条件下在LaAlO3单晶基底上制备了一系列YBCO超导薄膜.X射线衍射、扫描电镜和物性测量的结果表明,在成相热处理过程中气氛湿度对YBCO薄膜的结构和超导性能的有明显影响.干燥气氛成相的YBCO薄膜织构较好,表面较平整、致密,超导性能也较高,其临界超...     

PVP辅助低氟溶液法制备YBa_2Cu_3O_(7-x)厚膜研究(英文)

传统的化学溶液法制备微米级YBa2Cu3O7-x(YBCO)涂层导体过程中,需要反复多次镀膜和热分解过程才能使膜厚达到1μm以上。本研究以独特的先进低氟溶液为YBCO前驱溶液,通过添加聚吡咯烷酮(PVP)作为增稠剂,提高了YBCO胶体的粘度,并提高了最终YBCO薄膜的厚度及致密性。单次镀膜获得的YBCO薄膜厚度达到了600nm。77K,0T条件下,临界电流密度Jc达到1MA/cm2以上。这种高分子改性的低氟YBCO前驱溶液沉积技术有望在未来涂层导体开发中发挥作用.     

Conversion behavior comparison of TFA–MOD and non-fluorine solution-deposited YBCO films

The densification behavior during conversion of YBa₂Cu₃O_7−x (YBCO) films formed by the trifluoroacetate (TFA)-based metal–organic deposition (MOD) technique was compared to a non-fluorine oxycarbonate-based MOD process and nitrate-based polymer-assisted deposition (PAD). The critical current densities obtained in all processes exceeded 10⁶ A/cm² in films at least 300 nm thick. Rapid densification of films was observed in all processes, beginning at 700 °C in the TFA and PAD processes and 650 °C in the oxycarbonate process. YBCO nucleation occurred shortly after densification began in all processes. Residual carbon measurements were performed using wavelength dispersive spectroscopy (WDS). Carbon persisted in films from all processes until after densification began, but it was reduced to background levels soon after YBCO nucleation. Film density and second phase morphology were controlled through adjustments to the ambient oxygen partial pressure. Morphological evidence of extensive transient liquid phase formation was observed in PAD films and is consistent with the densification and nucleation behavior. The common behavior between the PAD, oxycarbonate–MOD, and TFA–MOD processes suggests that a melt forms in all systems, but the extent of this melt varies.     

化学溶液沉积快速制备YBCO超导薄膜研究

用传统的三氟乙酸盐—金属有机化合物热解法（简称TFA-MOD）来制备YBCO超导薄膜,由于制备时间长,不利于工业化.本文通过加入高沸点螯合剂二乙醇胺来改善前驱液性质,然后采用高温烧结一步法快速制备出完整的YBCO超导薄膜.制备的YBCO超导薄膜致密、几乎无a轴晶粒,YBCO（00l）峰具有立方取向,没有其他杂相峰.同时...     

Strongly enhanced flux pinning in the YBa_2Cu_3O_(7-X) films with the co-doping of Ba TiO_3 nanorod and Y_2O_3 nanoparticles at 65 K

YBa2Cu3O7-x(YBCO) films with co-doping BaTiO3(BTO) and Y2O3 nanostructures were prepared by metal organic deposition using trifluoroacetates(TFA-MOD). The properties of the BTO/Y2O3co-doped YBCO films with different excess yttrium have been systematically studied by x-ray diffraction(XRD), Raman spectra, and scanning electron microscope(SEM). The optimized content of yttrium excess in the BTO/Y2O3co-doped YBCO films is 10 mol.%, and the critical current density is as high as ~ 17 mA/cm2(self-field, 65 K) by the magnetic signal. In addition, the Y2Cu2O5 was formed when the content of yttrium excess increases to 24 mol.%, which may result in the deterioration of the superconducting properties and the microstructure. The unique combination of the different types of nanostructures of BTO and Y2O3 in the doped YBCO films, compared with the pure YBCO films and BTO doped YBCO films, enhances the critical current density(JC) not only at the self-magnetic field, but also in the applied magnetic field.     

添加Dy_2O_3的YBa_2Cu_3O_(7-δ)的临界电流密度特征

掺入Dy2O3的YBa2Cu3O7-δ(YBCO)粉末样品采用固相反应方法制备获得。XRD的Rietveld精修和SEM都显示Dy2O3和YBCO并存。随着添加相成分的增加,YBCO的开始转变温度Ton、超导临界温度Tc和零电阻温度Tc0都单调减小。对于某一固定的磁场,温度为77K,当x=0.05时,样品的临界电流密度Jc有最大值。磁场中,微量的Dy2O3的添加,使得YBCO临界电流密度增大。Jc的这些特征行为来自D2O3的添加导致的两方面的共同作用,一方面是超导性的变化,另一方面纳米尺寸范围内的空间分布的非均匀性。     

单源进液金属有机化学气相沉积法工作气压对YBCO薄膜制备的影响研究

基于金属有机化学气相沉积法(MOCVD),在沉积有Y2O3/YSZ/ CeO2( YYC)多层过渡层的Ni - W_at.5％金属基带上沉积YBa2Cu3O7-x(YBCO)超导薄膜.通过对单源进液系统的优化,使金属有机源连续稳定地输送到蒸发皿进行闪蒸.优化总气压并通入N2O气氛,以获得高质量的YBCO薄膜.在优化的温...     

利用微带谐振技术研究MgB_2/Al_2O_3和YBa_2Cu_3O_(7-x)/LaAlO_3超导薄膜的微波性质(英文)

利用微带谐振技术研究了MgB2/A12O3和YBa2Cu3o7-X/LaAlO3(YBCO/LAO)超导薄膜的微波性质.一个颗粒尺寸模型被用来分析超导薄膜的穿透深度和表面电阻.结果表明,对于高质的YBCO/LAO,微波性质主要由颗粒决定.对于低质的MgB2/Al2O3,该薄膜的微波性质主要由颗粒边界决定.     

Relationship between crystallization process and superconducting properties of YBCO films by TFA–MOD method using starting solution with various compositions

We have investigated the influence of partial pressure of water vapor [P(H₂O)] in the crystallization process on the superconducting properties of YBa₂Cu₃O_7−y (YBCO) films fabricated by a trifluoroacetate–metal organic deposition (TFA–MOD) method. The starting solution with different compositions of Y: Ba:Cu = 1.0:2.0:3.0 and 1.0:1.5:2.0 were studied. The critical current density (J_c) values of YBCO films fabricated from Y:Ba:Cu = 1.0:2.0:3.0 starting solution significantly increase (1.71 → 2.55 MA/cm²) with increasing P(H₂O) from 12.3 to 47.4 kPa. In the YBCO films fabricated from Y:Ba:Cu = 1.0:1.5:2.0 starting solution, high J_c values of over 2.5 MA/cm² were recognized in a wide range of P(H₂O) (12.3–47.4 kPa). One of the reason for J_c improvement is the suppression of coarsening of the secondary phases grains such as Y₂Cu₂O₅ and CuO due to increase in growth rate of YBCO layer in the crystallization process. The J_c values of all YBCO films decreased as P(H₂O) increased up to 70.1 kPa. This degradation of J_c values may be caused by difference of crystal growth mechanism in high growth rate.     

对靶溅射技术制备的La2/3Ca1/3MnO3/YBa2Cu4O8/La2/3Ca1/3MnO3薄膜中Tc的降低

本文用对靶溅射技术制备了La2/3Ca1/3MnO3/YBa2Cu4O8/La2/3Ca1/3MnO3薄膜.与YBCO单层薄膜相比,由于超导/铁磁系统中的磁性邻近效应,三层薄膜表现出较低的超导转变温度.薄膜的R～T测量曲线显示出超磁阻(CMR)效应和超导转变,预示着超导和铁磁特性共存于LCMO/YBCO/LCMO三文治结构.     

Strong flux pinning enhancement in YBa2Cu3O7-x films by embedded BaZrO3 and BaTiO3 nanoparticles

YBa2Cu3O7-x (YBCO) films with embedded BaZrO3 and BaTiO3 nanoparticles were fabricated by metalorganic deposition using trifluoroacetates (TFA-MOD). Both X-ray diffraction and transmission electron microscopy revealed that these BaZrO3 and BaTiO3 nanoparticles had random orientations and were distributed stochastically in the YBCO matrix. The unique combined microstructure enhances the critical current density (Jc) of the BaZrO3/BaTiO3 doped-YBCO films, while keeping the critical transition temperature (Tc) close to that in the pure YBCO films. These results indicate that BaZrO3 and BaTiO3 nanoparticles provide strong flux pinning in YBCO films.