多层平行裂隙型多孔介质通道内流体流动传热特性

基于Brinkman-extended Darcy模型和局部热平衡模型,对多层平行裂隙型多孔介质通道内的流动传热特性进行研究.获得了多层平行裂隙型多孔介质通道内各区域的速度场、温度场、摩擦系数及努塞尔数解析解,并分析了裂隙层数、达西数、空心率、有效热导率之比等对通道内流动传热特性的影响.结果表明:达西数较小时,通道多孔介质层内会出现不随高度变化的达西速度,此达西速度会随裂隙层数的增加而增大,但却不受各裂隙层下多孔介质层位置变化的影响.增加裂隙层数会减弱空心率对压降的影响,会使通道内流体压降升高,但升高程度会逐渐降低.增大热导率之比或减小空心率会使多裂隙通道内出现阶梯式温度分布,而在较小热导率之比或较大空心率时多裂隙情况下的温度分布曲线会趋于一致.此外,当热导率之比较小时,多层裂隙通道内的传热效果在任何空心率下都要优于单裂隙情况,当热导率之比较大时,存在临界空心率使各裂隙层数通道内的传热效果相同,且多裂隙通道内继续增加裂隙层数对传热强度影响不大.     

Linear and Weakly Nonlinear Stability Analyses of Two-Dimensional,Steady Brinkman–Bénard Convection Using Local Thermal Non-equilibrium Model

Effect of local thermal non-equilibrium (LTNE) on onset of Brinkman–Bénard convection and on heat transport is investigated. Rigid–rigid and free–free, isothermal boundaries are considered for investigation. The assumption of LTNE leads to an ‘advanced onset’ situation compared to that predicted by the local thermal equilibrium (LTE) assumption. This results in the ‘enhanced heat transport’ situation in the problem. Asymptotic analysis for small and large values of inter-phase heat transfer coefficient is also carried out on critical Rayleigh number, critical wave number and Nusselt number. In respect of boundary influences on onset and heat transport, it is found that classical results hold even under the LTNE assumption. The other parameters’ influences on onset and heat transport are qualitatively similar in LTNE and LTE cases.     

Effect of an Inserted Porous Layer Located at a Wall of a Parallel Plate Channel on Forced Convection Heat Transfer

A theoretical study is performed on heat and fluid flow in partially porous medium filled parallel plate channel. A uniform symmetrical heat flux is imposed onto the boundaries of the channel partially filled with porous medium. The dimensional forms of the governing equations are solved numerically for different permeability and effective thermal conductivity ratios. Then, the governing equations are made dimensionless and solved analytically. The results of two approaches are compared and an excellent agreement is observed, indicating correctness of the both solutions. An overall Nusselt number is defined based on overall thermal conductivity and difference between the average temperature of walls and mean temperature to compare heat transfer in different channels with different porous layer thickness, Darcy number, and thermal conductivity ratio. Moreover, individual Nusselt numbers for upper and lower walls are also defined and obtained. The obtained results show that the maximum overall Nusselt number is achieved for thermal conductivity ratio of 1. At specific values of Darcy number and thermal conductivity ratio, individual Nusselt numbers approach to infinity since the value of wall temperatures approaches to mean temperature.     

Numerical Simulation of Turbulent Flow and Heat Transfer in a Three-Dimensional Channel Coupled with Flow Through Porous Structures

This study investigates numerically the turbulent flow and heat transfer characteristics of a T-junction mixing, where a porous media flow is vertically discharged in a 3D fully developed channel flow. The fluid equations for the porous medium are solved in a pore structure level using an Speziale, Sarkar and Gatski turbulence model and validated with open literature data. Overall, two types of porous structures, consisted of square pores, are investigated over a wide range of Reynolds numbers: an in-line and a staggered pore structure arrangement. The flow patterns, including the reattachment length in the channel, the velocity field inside the porous medium as well as the fluctuation velocity at the interface, are found to be strongly affected by the velocity ratio between the transversely interacting flow streams. In addition, the heat transfer examination of the flow domain reveals that the temperature distribution in the porous structure is more uniform for the staggered array. The local heat transfer distributions inside the porous structure are also studied, and the general heat transfer rates are correlated in terms of area-averaged Nusselt number accounting for the effects of Reynolds number, velocity ratio as well as the geometrical arrangement of the porous structures.     

Forced Convection Heat Transfer of Nanofluids in a Porous Channel

This article is concerned with the effects of flow and migration of nanoparticles on heat transfer in a straight channel occupied with a porous medium. Investigation of force convective heat transfer of nanofluids in a porous channel has not been considered completely in the literature and this challenge is generally considered to be an open research topic that may require more study. The fully developed flow and steady Darcy?CBrinkman?CForchheimer equation is employed in porous channel. The thermal equilibrium model is assumed between nanofluid and solid phases. It is assumed that the nanoparticles are distributed non-uniformly inside the channel. As a result the volume fraction distribution equation is also coupled with governing equations. The effects of parameters such as Lewis number, Schmidt number, Brownian diffusion, and thermophoresis on the heat transfer are completely studied. The results show that the local Nusselt number is decreased when the Lewis number is increased. It is observed that as the Schmidt number is increased, the wall temperature gradient is decreased and as a consequence the local Nusselt number is decreased. The effects of Lewis number, Schmidt number, and modified diffusivity ratio on the volume fraction distribution are also studied and discussed.     

Perturbation Analysis of the Local Thermal Non-equilibrium Condition in a Fluid-Saturated Porous Medium Bounded by an Iso-thermal Channel

This study focuses analytically on the local thermal non-equilibrium (LTNE) effects in the developed region of forced convection in a saturated porous medium bounded by isothermal parallel-plates. The flow in the channel is described by the Brinkman–Forchheimer-extended Darcy equation and the LTNE effects are accounted by utilizing the two-equation model. Profiles describing the velocity field obtained by perturbation techniques are used to find the temperature distributions by the successive approximation method. A fundamental relation for the temperature difference between the fluid and solid phases (the LTNE intensity) is established based on a perturbation analysis. It is found that the LTNE intensity ( $\Delta \textit{NE}$ ) is proportional to the product of the normalized velocity and the dimensionless temperature at LTE condition. Also, it depends on the conductivity ratio, Da number, and the porosity of the medium. The intensity of LTNE condition ( $\Delta \textit{NE}$ ) is maximum at the middle of the channel and decreases smoothly to zero by moving to the wall. Finally, the established relation for the intensity of LTNE condition is simple and fundamental for estimating the importance of LTNE condition and validation of numerical simulation results.     

The Use of Porous Fins for Heat Transfer Augmentation in Parallel-Plate Channels

In this study, a steady, fully developed laminar forced convection heat augmentation via porous fins in isothermal parallel-plate duct is numerically investigated. High-thermal conductivity porous fins are attached to the inner walls of two parallel-plate channels to enhance the heat transfer characteristics of the flow under consideration. The Darcy–Brinkman–Forchheimer model is used to model the flow inside the porous fins. This study reports the effect of several operating parameters on the flow hydrodynamics and thermal characteristics. This study demonstrates, mainly, the effects of porous fin thickness, Darcy number, thermal conductivity ratio, Reynolds number, and microscopic inertial coefficient on the thermal performance of the present flow. It is found that the highest Nusselt number is achieved at fully filled porous duct which requires the highest pumping pressure. The results show that using porous fins requires less pumping pressure with comparable high heat augmentation weight against fully filled porous duct. It is found that higher Nusselt numbers are achieved by increasing the microscopic inertial coefficient (A), the Reynolds number (Re), and the thermal conductivity of the porous substrate k ₂. The results show that heat transfer can be enhanced (1) with the use of high thermal conductivity fins, (2) by decreasing the Darcy number, and (3) by increasing microscopic inertial coefficient.     

Stationary Fingering Instability in a Non-equilibrium Porous Medium with Coupled Molecular Diffusion

Finger type double diffusive convective instability in a fluid-saturated porous medium is studied in the presence of coupled heat-solute diffusion. A local thermal non-equilibrium (LTNE) condition is invoked to model the Darcian porous medium which takes into account the energy transfer between the fluid and solid phases. Linear stability theory is implemented to compute the critical thermal Rayleigh number and the corresponding wavenumber exactly for the onset of stationary convection. The effects of Soret and Dufour cross-diffusion parameters, inter-phase heat transfer coefficient and porosity modified conductivity ratio on the instability of the system are investigated. The analysis shows that positive Soret mass flux triggers instability and positive Dufour energy flux enhances stability whereas their combined influence depends on the product of solutal Rayleigh number and Lewis number. It also reveals that cell width at the convection threshold gets affected only in the presence of both the cross-diffusion fluxes. Besides, asymptotic solutions for both small and large values of the inter-phase heat transfer coefficient and porosity modified conductivity ratio are found. An excellent agreement is found between the exact and asymptotic solutions.     

Numerical Study of Heat Transfer in a Rectangular Channel with Porous Covering Obstacles

A numerical study is performed to analyze steady laminar forced convection in a channel in which discrete heat sources covered with porous material are placed on the bottom wall. Hydrodynamic and heat transfer results are reported. The flow in the porous medium is modeled using the Darcy–Brinkman–Forchheimer model. A computer program based on control volume method with appropriate averaging for diffusion coefficient is developed to solve the coupling between solid, fluid, and porous region. The effects of parameters such as Reynolds number, Prandtl number, inertia coefficient, and thermal conductivity ratio are considered. The results reveal that the porous cover with high thermal conductivity enhances the heat transfer from the solid blocks significantly and decreases the maximum temperature on the heated solid blocks. The mean Nusselt number increases with increase of Reynolds number and Prandtl number, and decrease of inertia coefficient. The pressure drop along the channel increases rapidly with the increase of Reynolds number.     

Thermodynamically Consistent Limiting Forced Convection Heat Transfer in a Asymmetrically Heated Porous Channel: An Analytical Study

Fluid transport and the associated heat transfer through porous media is of immense importance because of its numerous practical applications. In view of the widespread applications of porous media flow, the present study attempts to investigate the forced convective heat transfer in the limiting condition for the flow through porous channel. There could be many areas, where heat transfer through porous channel attain some limiting conditions, thus, the analysis of limiting convective heat transfer is far reaching. The primary aim of the present study is focused on the limiting forced convection analysis considering the flow of Newtonian fluid between two asymmetrically heated parallel plates filled with saturated porous media. Utilizing a few assumptions, which are usually employed in the literature, an analytical methodology is executed to obtain the closed-form expression of the temperature profile, and in the following the expression of the limiting Nusselt numbers. The parametric variations of the temperature profile and the Nusselt numbers in different cases have been shown highlighting the influential role of different performance indexing parameters, like Darcy number, porosity of the media, and Brinkman number of forced convective heat transfer in porous channel. In doing so, the underlying physics of the transport characteristics of heat has been delineated in a comprehensive way. Moreover, a discussion has been made regarding an important feature like the onset of point of singularity as appeared on the variation of the Nusselt number from the consideration of energy balance in the flow field, and in view of second law of thermodynamics.     

Free Convection Heat Transfer From A Sphere In A Porous Medium Using A Thermal Non-equilibrium Model

This work studies the free convection heat transfer from a sphere with constant wall temperature embedded in a fluid-saturated porous medium using a thermal non-equilibrium model. The governing equations are transformed into boundary-layer partial differential equations by the coordinate transform, and the obtained governing equations are then solved by the cubic spline collocation method. The temperature distributions for fluid and solid phases are shown for different values of the porosity scaled thermal conductivity ratio, the interphase heat transfer parameter, and the streamwise coordinate. The effects of the porosity scaled thermal conductivity ratio and the interphase heat transfer parameter between solid and fluid phases on the local Nusselt numbers for fluid and solid phases are examined. Results show the local Nusset number for the porous medium can be increased by increasing the porosity scaled thermal conductivity ratio. Moreover, the thermal non-equilibrium effect is more significant for low values of the porosity scaled thermal conductivity ratio or the interphase heat transfer parameter.     

Lattice Boltzmann Pore Scale Simulation of Natural Convection in a Differentially Heated Enclosure Filled with a Detached or Attached Bidisperse Porous Medium

In this research, pore scale simulation of natural convection in a differentially heated enclosure filled with a conducting bidisperse porous medium is investigated using the thermal lattice Boltzmann method. For the first time, the effect of connection of the bidisperse porous medium to the enclosure walls is studied by considering the attached geometry in addition to the detached one. Effect of most relevant parameters on the streamlines and isotherms as well as hot wall average Nusselt number is studied for two of the bidisperse porous medium configurations. It is observed that effect of geometrical and thermo-physical parameters of the bidisperse porous medium on the heat transfer characteristics is more complicated for the attached configuration. To assess the validity of the local thermal equilibrium condition in the micro-porous media, the pore scale results are used to compute the percentage of the local thermal non-equilibrium for two of the bidisperse porous medium configurations. It is concluded that for the detached configuration, the local thermal equilibrium condition is confirmed in the entire micro-porous media for the ranges of the parameters studied here. However, for the attached geometry, it is shown that departure from the local thermal equilibrium condition is observed for the higher values of the Rayleigh number, micro-porous porosity, solid–fluid thermal conductivity ratio, and the smaller values of the macro-pores volume fraction.     

Validation of the Local Thermal Equilibrium Assumption in Forced Convection of Non-Newtonian Fluids through Porous Channels

In this paper, we assess the validity of the local thermal equilibrium assumption in the non-Newtonian forced convection flow through channels filled with porous media. For this purpose, the problem is solved numerically using local thermal non-equilibrium and non-Darcian models. Numerical solutions obtained over broad ranges of representative dimensionless parameters are utilized to map conditions at which the local thermal equilibrium assumption can or cannot be employed. The circumstances of a higher modified Peclet number, a lower modified Biot number, a lower fluid-to-solid thermal conductivity ratio, a lower power-law fluid index, and a lower microscopic and macroscopic frictional flow resistance coefficients, are identified as unfavorable circumstances for the local thermal equilibrium (LTE) condition to hold. Quantitative LTE validity maps that reflect the proportional effect of each parameter as related to others are presented.     

Mixed Convection Heat Transfer in the Annulus Between Two Concentric Vertical Cylinders Using Porous Layers

A numerical investigation of the steady-state, laminar, axi-symmetric, mixed convection heat transfer in the annulus between two concentric vertical cylinders using porous inserts is carried out. The inner cylinder is subjected to constant heat flux and the outer cylinder is insulated. A finite volume code is used to numerically solve the sets of governing equations. The Darcy–Brinkman–Forchheimer model along with Boussinesq approximation is used to solve the flow in the porous region. The Navier–Stokes equation is used to describe the flow in the clear flow region. The dependence of the average Nusselt number on several flow and geometric parameters is investigated. These include: convective parameter, λ, Darcy number, Da, thermal conductivity ratio, K _r, and porous-insert thickness to gap ratio (H/D). It is found that, in general, the heat transfer enhances by the presence of porous layers of high thermal conductivity ratios. It is also found that there is a critical thermal conductivity ratio on which if the values of Kr are higher than the critical value the average Nusselt number starts to decrease. Also, it found that at low thermal conductivity ratio (K _r ≈ 1) and for all values of λ the porous material acts as thermal insulation.     

Modeling and Simulation of Local Thermal Non-equilibrium Effects in Porous Media with Small Thermal Conductivity

The two-equation model in porous media can describe the local thermal non-equilibrium (LTNE) effects between fluid and solid at REV scale, with the temperature differences in a solid particle neglected. A multi-scale model has been proposed in this study. In the model, the temperature differences in a solid particle are considered by the coupling of the fluid energy equation at REV scale with the heat conduction equation of a solid particle at pore scale. The experiments were conducted to verify the model and numerical strategy. The multi-scale model is more suitable than the two-equation model to predict the LTNE effects in porous media with small thermal conductivity. The effects of particle diameter, mass flow rate, and solid material on the LTNE effects have been investigated numerically when cryogenic nitrogen flows through the porous bed with small thermal conductivity. The results indicate that the temperature difference between solid center and fluid has the same trend at different particle diameters and mass flow rates, while the time to reach the local thermal equilibrium is affected by solid diameter dramatically. The results also show that the temperature difference between solid center and surface is much greater than that between solid surface and fluid. The values of \( \rho {\text{c}} \) for different materials have important influence on the time to reach the local thermal equilibrium between solid and fluid.     

Fully-developed conjugate heat transfer in porous media with uniform heating

We propose a computational method for approximating the heat transfer coefficient of fully-developed flow in porous media. For a representative elementary volume of the porous medium we develop a transport model subject to periodic boundary conditions that describes incompressible fluid flow through a uniformly heated porous solid. The transport model uses a pair of pore-scale energy equations to describe conjugate heat transfer. With this approach, the effect of solid and fluid material properties, such as volumetric heat capacity and thermal conductivity, on the overall heat transfer coefficient can be investigated. To cope with geometrically complex domains we develop a numerical method for solving the transport equations on a Cartesian grid. The computational method provides a means for approximating the heat transfer coefficient of porous media where the heat generated in the solid varies “slowly” with respect to the space and time scales of the developing fluid. We validate the proposed method by computing the Nusselt number for fully developed laminar flow in tubes of rectangular cross section with uniform wall heat flux. Detailed results on the variation of the Nusselt number with system parameters are presented for two structured models of porous media: an inline and a staggered arrangement of square rods. For these configurations a comparison is made with literature on fully-developed flows with isothermal walls.     

Analysis of fluid flow and heat transfer in a channel with intermittent heated porous blocks

A numerical study of forced convection enhancement in a channel intermittently heated is presented in this work. The use of porous blocks mounted on the heated parts of the channel to improve thermal performance is investigated. In order to account for the inertia, drag and boundary effects, the Brinkman-Forchheimer-extended Darcy model is adopted for the flow inside the porous regions. The effects of several parameters such as Darcy number, the block dimensions, the number of blocks and the thermal conductivity ratio are documented. The results show that the blocks may alter substantially the flow pattern depending on the permeability of the porous medium, and may improve the heat transfer and reduce the wall temperature under certain circumstances. Received on 9 June 1997     

Natural Convection in a Cavity Filled with Porous Layers on the Top and Bottom Walls

Natural convection in a partially filled porous square cavity is numerically investigated using SIMPLEC method. The Brinkman-Forchheimer extended model was used to govern the flow in the porous medium region. At the porous-fluid interface, the flow boundary condition imposed is a shear stress jump, which includes both the viscous and inertial effects, together with a continuity of normal stress. The thermal boundary condition is continuity of temperature and heat flux. The results are presented with flow configurations and isotherms, local and average Nusselt number along the cold wall for different Darcy numbers from 10⁻¹ to 10⁻⁶, porosity values from 0.2 to 0.8, Rayleigh numbers from 10³ to 10⁷, and the ratio of porous layer thickness to cavity height from 0 to 0.50. The flow pattern inside the cavity is affected with these parameters and hence the local and global heat transfer. A modified Darcy–Rayleigh number is proposed for the heat convection intensity in porous/fluid filled domains. When its value is less than unit, global heat transfer keeps unchanged. The interfacial stress jump coefficients β ₁ and β ₂ were varied from  −1 to +1, and their effects on the local and average Nusselt numbers, velocity and temperature profiles in the mid-width of the cavity are investigated.     

Effect of rotation on ferromagnetic porous convection with a thermal non-equilibrium model

The effect of rotation on the onset of thermal convection in a horizontal layer of ferrofluid saturated Brinkman porous medium is investigated in the presence of a uniform vertical magnetic field using a local thermal non-equilibrium (LTNE) model. A two-field model for temperature representing the solid and fluid phases separately is used for energy equation. The condition for the occurrence of stationary and oscillatory convection is obtained analytically. The stability of the system has been analyzed when the magnetic and buoyancy forces are acting together as well as in isolation and the similarities as well as differences between the two are highlighted. In contrast to the non-rotating case, it is shown that decrease in the Darcy number Da and an increase in the ratio of effective viscosity to fluid viscosity Λ is to hasten the onset of stationary convection at high rotation rates and a coupling between these two parameters is identified in destabilizing the system. Asymptotic solutions for both small and large values of scaled interphase heat transfer coefficient H _t are presented and compared with those computed numerically. Besides, the influence of magnetic parameters and also parameters representing LTNE on the stability of the system is discussed and the veracity of LTNE model over the LTE model is also analyzed.     

An experimental study of steam injection into a uniform water flow through porous media

An experimental study of steam injection into a porous media was carried out in a 2-dimensional plane porous channel. The steam was injected into a uniform downward water flow in a vertically aligned porous channel. The steam-water interface was carefully observed to understand the underlying physics. Two steam injection rate bounds were found for a given water flow rate and water subcooling. The upper bound is the steam flow rate at which the steam zone grows without limit and the lower bound is the steam flow rate at which a steam zone is just initiated. The bounds were determined experimentally for a porous channel with different permeabilities and thermal conductivities. For large particle size, chaotic oscillation of steam water interface was observed. The oscillation is believed to enhance heat and momentum transfer mechanisms. The steam zone size and shape were measured to evaluate heat transfer characteristics. The average Nusselt number is presented in terms of steam and water Reynolds numbers and the Stefan number.