Carbon black oxidation mechanism in loose and tight contacts with Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and CeO<Subscript>2</Subscript> catalysts

The catalytic combustion of carbon black was investigated in the presence of CeO₂ and Al₂O₃. The influence of contact type between carbon particles and these oxides was examined by thermal analysis, the BET specific area, and EPR spectroscopy. For tight contact carbon black-catalyst mixtures, a new paramagnetic species is observed and can be considered as a fingerprint of the contact between the two solids. These new paramagnetic species increase the reactivity of the catalytic reaction of carbon black (CB) combustion and take part in the oxidation mechanism of CB. Published in Russian in Kinetika i Kataliz, 2007, Vol. 48, No. 6, pp. 899–904. This article was submitted by the authors in English.     

Kinetic studies on the hydrogenation of nitrate in water using Rh/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and Rh-Cu/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts

Liquid-phase reduction NO ₃ ⁻ using monometallic and bimetallic catalysts (5% Rh/Al₂O₃, 5% Rh-0.5% Cu/Al₂O₃, 5% Rh-1.5% Cu/Al₂O₃, 5% Rh-5% Cu/Al₂O₃ and a physical mixture of 5% Rh/Al₂O₃ and 1.5% Cu/Al₂O₃) was studied in a slurry reactor operating at atmospheric pressure. Kinetic measurements were performed for a low concentration of nitrate (0.4 × 10⁻³−3.2 × 10⁻³ mol dm⁻³) and the temperature range 293–313 K. From the experimental data, it was found that the reduction of nitrate is first order with respect to nitrate. On the basis of the rate constants, the apparent activation energy was established using a graphic method. Published in Russian in Kinetika i Kataliz, 2007, Vol. 48, No. 6, pp. 881–886. This article was submitted by the authors in English.     

Reactivation of CoMo/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> hydrotreating catalysts with chelating agents

Effect of various chelating components, multibasic carboxylic acids and glycols, used to prepare hydrotreating catalysts on the activity regeneration of calcined hydrotreating catalysts was studied. Reactivated catalyst samples were tested in a model reaction of hydrodesulfurization of dibenzothiophene. It was shown that the treatment of calcined catalysts with the chelating components leads to an increase in the catalytic activity. The best catalytic characteristics are observed for the catalyst reactivated with a solution containing citric acid and triethylene glycol.     

Co-Mo/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and Ni-W/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts: Potential and prospects for use in hydrotreating of light cycle oil from catalytic cracking

Со-Мо/Al₂O₃ and Ni-W/Al₂O₃ catalysts were tested in hydrotreating of light cycle oil from catalytic cracking, of the straight-run gasoil, and of their mixture under typical hydrotreating conditions used in industry. The catalysts prepared using PMo₁₂ and PW₁₂ heteropoly acids exhibit high catalytic activity. The Со-Мо/Al₂O₃ catalyst is more active in hydrodesulfurization and hydrogenation of olefin and diene hydrocarbons, whereas the Ni-W/Al₂O₃ catalysts are more active in hydrogenation of mono- and polycyclic aromatic hydrocarbons. Comparison of the quality characteristics of the hydrogenizates obtained with the requirements of the technical regulations shows that the required levels of the sulfur content and cetane number of the hydrogenizates at practically accessible process parameters can be reached for mixtures of the straight-run gasoil and light cycle oil from catalytic cracking with high content of the latter component only when the process with the Со-Мо/Al₂O₃ system and Ni-W/Al₂O₃ catalysts is performed in two steps.     

Thermal stability of Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>

Differential thermal analysis (DTA) and thermogravimetric analysis (TGA) of an α-Bi₂O₃ sample revealed staged phase transitions in the range 720–800°C (at 720, 780, and 800°C) and the elimination of oxygen to the composition Bi₂O_2.967 during heating to 895°C in air at 16 K/min. In dynamic vacuum (p = 1.33 Pa) at 780–800°C, Bi₂O₃ consecutively transforms to a phase with the cubic γ-Bi₂O₃ structure and tetragonal Bi₂O_2.3?2.4. In the latter, electron diffraction in a transmission electron microscope (ED/TEM) shows a superstructure with the superstructure vector q ₁₁₀ ≈ 1/9, which indicates an ordered arrangement of oxygen vacancies.     

Thermal stability and catalytic properties of the composite amorphous Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-nanocrystals ZrO<Subscript>2</Subscript>

Catalytic properties in relation to the hydrogen oxidation reaction and thermal stability of materials based on the nanocomposite amorphous Al₂O₃-nanocrystalline ZrO₂ were studied.     

Gold catalysts supported on ZnO/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> for low-temperature CO oxidation

Gold catalysts with loadings ranging from 0.5 to 7.0 wt% on a ZnO/Al₂O₃ support were prepared by the deposition–precipitation method (Au/ZnO/Al₂O₃) with ammonium bicarbonate as the precipitation agent and were evaluated for performance in CO oxidation. These catalysts were characterized by inductively coupled plasma-atom emission spectrometry, temperature programmed reduction, and scanning transmission electron microscopy. The catalytic activity for CO oxidation was measured using a flow reactor under atmospheric pressure. Catalytic activity was found to be strongly dependent on the reduction property of oxygen adsorbed on the gold surface, which related to gold particle size. Higher catalytic activity was found when the gold particles had an average diameter of 3–5 nm; in this range, gold catalysts were more active than the Pt/ZnO/Al₂O₃ catalyst in CO oxidation. Au/ZnO/Al₂O₃ catalyst with small amount of ZnO is more active than Au/Al₂O₃ catalyst due to higher dispersion of gold particles.     

Thermal synthesis of the CeO<Subscript>2</Subscript>-PrO<Subscript>2</Subscript>-Nd<Subscript>2</Subscript>O<Subscript>3</Subscript>pigments

Summary The synthesis of new compounds based on the CeO₂-PrO₂-Nd₂O₃system, which can be used as pigments for colouring of ceramic glazes, is investigated in our laboratory. The optimum conditions for the syntheses of these compounds have been estimated. The methods of thermal analysis provided first information about the temperature region of the formation of the pigments investigated. The synthesis of these compounds was followed by thermal analysis using STA 449/C Jupiter (Netzsch, Germany).     

Hydrogenolysis of glycerol to propanediols over heteropolyacids promoted AgCu/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts

Various amounts and different types of heteropolyacids promoted 5Ag15Cu/Al₂O₃ catalysts were prepared by impregnation method and analyzed through many techniques. The synthesized catalysts were evaluated for hydrogenolysis of glycerol to propanediols. The results demonstrated that heteropolyacids loading facilitated the reduction, promoted the dispersion, enhanced the acidity, and increased Broensted acid sites of the AgCu catalysts, which benefited the generation of 1,3-propanediol. Compared with phosphotungstic acid and phosphomolybdic acid, silicotungstic acid promoted AgCu catalyst had a better performance for 1,3-propanediol due to the better Cu dispersion and higher Broensted acidity. In addition, when the reaction was performed at 220 °C under 3.5 MPa for 8 h, the chosen 5Ag15Cu-10HSiW/Al₂O₃ achieved a 69.6% glycerol conversion with 35.6% 1,2-propanediol selectivity and 21.5% 1,3-propanediol selectivity.     

One-pot synthesis of Nb-modified Al<Subscript>2</Subscript>O<Subscript>3</Subscript> support for NiMo hydrodesulfurization catalysts

The effect of Nb as a support modifier on the NiMo₆/Al₂O₃–Nb₂O₅(x) (x?=?0, 1, 4, and 8?wt% Nb) catalysts was studied. The supports were prepared by one-pot coprecipitation from soluble precursors. The XRF analysis of the catalysts showed that the contents of Mo and Ni increased slightly with the presence of Nb. Micropore area and pore volume augmented importantly with Nb content, resulting in pore diameters between 5.3 and 9.3?nm. XPS analysis showed that the presence of Nb decreases the active metal–support interaction, improving the Mo and Ni sulfidation degree. The Raman spectra of sulfided catalysts suggested an increase in the number of layers of MoS₂ in the presence of Nb. Generally, the thiophene HDS activity at normal pressure of sulfided NiMo₆/Al₂O₃–Nb₂O₅(8) was greater than that of the sulfided catalysts with x?=?0, 1, and 4?wt% Nb, which can be attributed to the Nb promotion that would have an effect on the type of active site (Brønsted or Lewis acidic sites), since the number of sites by CO chemisorption for sulfided NiMo₆/Al₂O₃–Nb₂O₅(x) did not show correlation with the catalytic activity. The high-pressure HDS activity of dibenzothiophene was also greater in the presence of Nb, and the hydrogenation route was preferred for the Nb-promoted solid, while the unpromoted one showed a larger yield of direct desulfurization products.

Open image in new window

     

Composition of the gas phase over Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and the enthalpies of atomization of AlO,Al<Subscript>2</Subscript>O,and Al<Subscript>2</Subscript>O<Subscript>2</Subscript>

The A1, O, AlO, A1₂O, Al₂O₂, WO₂, and WO₃, partial pressures in the vapor over Al₂O₃ in a tungsten Knudsen effusion cell between 2300 and 2600 K were derived from A1⁺, O⁺, AlO⁺, A1₂O⁺, Al₂O₂⁺, WO₂⁺, and WO₃⁺, ion intensities. The mass spectrometer was calibrated against the equilibrium constant of the WO₃(g) = WO₂(g) + O(g) reaction. Refined values of the ionization cross sections of AlO and A1₂O₂ were used in the partial pressure calculations. The enthalpies of atomization of aluminum suboxides were determined to be Δ_at H ^o(AlO, g, 0) = 510.7 ± 3.3 kJ mol⁻¹, Δ_at H ^o(Al₂O, g, 0) = 1067.2 ± 6.9 kJ mol⁻¹, and Δ_at H ^o(Al₂O₂, g, 0) = 1556.7 ± 9.9 kJ mol⁻¹.     

Reaction of indoles with ethyl bromopropynoate over Al<Subscript>2</Subscript>O<Subscript>3</Subscript> surface

1H-Indole and 2-methyl-1H-indole reacted with ethyl 3-bromopropynoate over aluminum oxide to give mixtures of the corresponding ethyl 3-(1H-indol-3-yl)propynoates and ethyl 3,3-bis(1H-indol-3-yl)-acrylates, the latter prevailing.     

Investigation of macro-/mesoporous Re<Subscript>2</Subscript>O<Subscript>7</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts prepared by a particle-template method for butylene metathesis

Macro-/mesoporous Al₂O₃ supports were prepared by using monodisperse polystyrene (PS) microspheres as a template. The pore volume and BET surface area of the Al₂O₃ supports increased considerably with increasing amounts of the PS microspheres; further investigation showed that PS template only increased the volume of macro-pores but did not change the volume of meso-pores or micro-pores. Macro-/mesoporous Re₂O₇/Al₂O₃ metathesis catalysts were prepared through loading Re₂O₇ onto the as-prepared macro-/mesoporous Al₂O₃ supports, and their catalytic performance was tested in a fixed-bed tubular reactor using the metathesis of normal butylenes as a probe reaction. The results showed that the prepared macro-/mesoporous Re₂O₇/Al₂O₃ catalyst had high activity with consistent selectivity; propylene and pentene accounted for more than 90 wt% of the metathesis products, while the amount of ethylene plus hexane was less than 10 wt%, the majority of which was hexane. These Re₂O₇/Al₂O₃ catalysts had not only higher activity, but also longer working life span and higher tolerance to carbon residues than conventional Re₂O₇/Al₂O₃ catalysts.     

Laser-induced luminescence associated with surface hydroxide groups in Al<Subscript>2</Subscript>O<Subscript>3</Subscript>

Laser-induced luminescence of OH_s groups for undoped Al₂O₃ oxides of various phase compositions was excited by pulsed nitrogen laser radiation at 337.1 nm. The luminescence band at 500–650 nm assigned to hydroxide groups of Al₂O₃, actually, consists of several lines at 500–515, 553, 567, 577, 607, and 633 nm; these constituent bands can be assigned to various types of OH_s surface groups. In the low-temperature phases of the γ→δ→θ-Al₂O₃ series, excitation at a wavelength of 337.1 nm gave rise to a characteristic luminescence band associated with surface hydroxide groups of Al₂O₃ that appeared at 770 nm.     

Effect of heat treatment on magnetic MgFe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanoparticles

MgFe₂O₄ (Mg-ferrite) nanoparticles encapsulated in amorphous SiO₂ were prepared by the wet chemical method. The particle sizes were estimated, based on the X-ray diffraction peaks, to be between 3 and 8 nm, depending on the annealing temperature. The particle size increased as the annealing temperature increased. From the magnetization measurements, the blocking temperature, T _b, was found to be between 30 and 60 K. The magnetization values varied with the annealing or quenching conditions. To clarify the process of crystal growth, thermogravimetric and differential thermal analysis (TG-DTA) measurements were performed and the results were compared with the X-ray diffraction patterns.     

Molecular mechanism of formation of supported platinum catalysts of the Pt/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> family

Certain stages of the classical procedure for preparing aluminum-platinum catalysts, whose understanding is important from both the basic and practical viewpoints, are considered on the molecular level. Properties of both participants (active component precursor solution and oxide surface) are shown to be inhomogeneous, which can affect interaction of the components at the fixing stage. Existing views (and their evolution) on the mechanism of adsorption of platinum complexes from aqueous solutions on aluminum oxide surface are discussed. The role of chemical processes on the stage of fixing precursor on the electronic and structural properties of the supported metal is demonstrates. Strong metal-support interaction is shown to endow platinum with specific adsorption and catalytic properties in hydrocarbon transformation reactions.     

Selective oxidation of carbon monoxide in hydrogen-containing gas on CuO-CeO<Subscript>2</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts prepared by surface self-propagating thermal synthesis

The CuO-CeO₂/Al₂O₃ catalysts for the selective oxidation of CO in hydrogen-containing mixtures were prepared by surface self-propagating thermal synthesis (SSTS) with the use of cerium nitrate Ce(NO₃)₃, the ammonia complex of copper acetate [Cu(NH₃)₄](CH₃COO)₂, and citric acid C₆H₈O₇ as a fuel additive. The effect of the C₆H₈O₇/Ce(NO₃)₃ molar ratio on the catalyst activity and selectivity for oxygen was studied. The catalyst samples were studied by X-ray diffraction (XRD) analysis, temperature-programmed reduction (TPR-H₂), IR spectroscopy of adsorbed CO, and transmission electron microscopy (TEM). It was found that an increase in the C₆H₈O₇/Ce(NO₃)₃ ratio resulted in an increase in the degree of dispersion of the resulting CeO₂ phase. The greatest amount of dispersed CuO particles, which are responsible for catalytic activity in the oxidation of CO, was formed at C₆H₈O₇/Ce(NO₃)₃ = 1.     

Thermal analysis of binary system Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-SnO<Subscript>2</Subscript> obtained by sol-gel technique

Summary A series of Al₂O₃-SnO₂ catalysts with Al₂O₃ to SnO₂ molar ratio of 1:1, 1:0.5, 1:0.2 and 1:0.1 were synthesized by sol-gel technique and characterized by thermal analysis and FTIR. In the case of binary gels - addition of tin component leads to better crosslinking than in pure alumina gel and as a result to a much uniform texture structure.     

A comparative study of Ir/Ga<Subscript>2</Subscript>O<Subscript>3</Subscript>, Pt/Ga<Subscript>2</Subscript>O<Subscript>3</Subscript>, and Ru/Ga<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts in selective hydrogenation of crotonaldehyde

Catalytic performance of gallia-supported iridium catalysts in the reaction of selective hydrogenation of crotonaldehyde in the gas phase was studied and compared to that of platinum and ruthenium catalysts. The best catalytic properties in terms of the selectivity to crotyl alcohol are shown by 5 wt % Pt/α-Ga₂O₃ and 5 wt % Ir/α-Ga₂O₃ catalysts prepared from nonchlorine precursors: Pt(acac)₂ and Ir(acac)₃, but for the 5 wt % Pt/α-Ga₂O₃ a very high selectivity of 75% at the high conversion (ca. 60%) is observed. A high selectivity of galia-supported iridium and platinum catalysts was explained by the surface reducibility of gallium oxide leading to covering (decoration) of platinum and iridium by gallium suboxides and the promoting effect of gallium.