Structural distribution and rigidity of the glass network determined by EPR of Cu

The linewidth-broadening of the EPR spectra of Cu²⁺ in silicate, borate and phosphate glasses was analyzed in terms of the distribution of g_| and A_| (δ_| and δA_|) and related to the distribution of the rigidity of the network structure. X- and K-band spectra were measured for the glasses doped with ⁶³Cu²⁺ (93% abundance). The linewidth of the HFS shoulders with parallel orientation to H increased linearly with increasing m or microwave frequency. δg_| and δA_| showed a marked dependence on glass composition. For example, in Na₂O---B₂O₃ glasses, on going from x (mol% of Na₂O) being small through intermediate to large, δg_| varied from small through large to negligibly small. In contrast to these glasses δg_| was extremely large for 75PbO · 25B₂O₃ glass. The large δg_| for the Na₂O---B₂O₃ glassesof intermediate x was attributed to the coexistence of various borate groups competitively coordinating to Cu²⁺. Negligibly small δg_| for 70Na₂O · 30B₂O₃ glass and extremely large δg_| for 75PbO ·25B₂O₃ glass, both with a narrower structural distribution, reflect regidity of the glass network. The Pb---O bonding is strong enough to distort the coordination of Cu²⁺-complex. The situation is the reverse in Na₂O---B₂O₃ glasses.     

An infrared study of crystallization in sodium-disilicate glasses containing iron oxides

The infrared absorption spectra of sodium-disilicate glasses containing various amounts of Fe₂O₃ ([Na₂O · 2 SiO₂]_1−x [Fe₂O₃]_x, where X = 0.05, 0.1 and 0.2) were investigated in the wavenumber range from 200–2000 cm⁻¹. The addition of Fe₂O₃ to the sodium-disilicate glass does not seem to introduce any new absorption band as compared with the spectrum of a pure sodium-disilicate glass; nevertheless, a general shift of the existing absorption bands toward lower wavenumbers is observed. The amount of shift is, in fact, proportional to the content of Fe₂O₃ in the glass. This observation is consistent with the recently proposed structural model for the bonding of Fe³⁺ ions in the iron-sodium-silicate glass system.

Annealing of 20 mol% iron oxide glasses at 550 and 580°C produced an extra sharp infrared absorption peak at about 610 cm⁻¹ wavenumber. This new peak is believed to be related to the crystallized particles of the glass as concluded from both a scanning electron micrograph and an electron diffraction pattern.     

Li conductivity in lithium niobate: silica glasses

Glasses of composition 65 mol% LiNbO₃:: 35 mol% SiO₂ have been shown to be Li⁺ ion conductors with a conductivity at 200°C > 1 × 10⁻⁵ (η cm)⁻¹ and an activation energy of 0.54 eV. The addition of approximately 0.1 mol% Fe₂O₃ leads to an enhancement of conductivity to ≈10⁻³ (η cm)⁻¹ at 200°C and an activation energy of 0.67 eV. The effect of Fe is shown to be in the control of microstructure in the glass, with Fe₂O₃ concentrations < 1 mol% acting as a grain growth inhibitors and larger concentrations acting as a nucleating agents. A model for this process based on the expected stoichiometry of the melt and the effect of Fe²⁺ and Fe³⁺ in charge compensation is in excellent agreement with experimental data from electron spin resonance.     

The effect of mixed alkaline earths on the diffusivity and the incorporation of iron in 5Na2O · xMgO · (15−x)CaO · yAl2O3 · (80−y)SiO2 melts

Diffusion coefficients of iron were measured in glass melts with the basic compositions 5Na₂O · xMgO · (15−x)CaO · yAl₂O₃ · (80−y)SiO₂ with x=5, 10 and y=0, 5, 7.5, 10 and 15. The melts were doped with 0.25 mol% Fe₂O₃ and studied in the temperature range from 1000 to 1600 °C using square-wave voltammetry. The voltammograms exhibited distinct peaks attributed to the reduction of Fe³⁺ to Fe²⁺, from which peak currents mixed diffusion coefficients of iron were calculated. Diffusion coefficients in all melt compositions which did not show crystallization could be fitted to Arrhenius equation. The diffusivities measured in different melt compositions were related to the same viscosity, i.e. not the same temperature. Increasing the alumina concentration from 5 to 10 mol% resulted in an increase of the viscosity corrected diffusivities. At further increasing alumina concentrations, the diffusivities get smaller again. This can be explained by the stabilizing effect of Na⁺ and Ca²⁺ on FeO⁻₄ and AlO⁻₄-tetrahedra, which strengthens the incorporation of Fe³⁺ into the glass structure.     

The effect of MgO on the thermodynamics of the Fe/Fe-redox equilibrium and the incorporation of iron in soda-magnesia-aluminosilicate melts

Melts with the basic compositions 10Na₂O · 10MgO · xAl₂O₃ · (80−x)SiO₂ (x=0, 5, 10, 15 and 20), 10Na₂O · xMgO · 10Al₂O₃ · (80−x)SiO₂ (x=5, 10, 15 and 20) and xNa₂O · 10MgO · 10Al₂O₃ · (80−x)SiO₂ (x=5, 10 and 15) all doped with 0.25 mol% Fe₂O₃ were studied using square-wave voltammetry. The temperatures applied were in the range of 1000–1600 °C. The square-wave voltammograms recorded show peaks caused by the reduction of Fe³⁺ to Fe²⁺. The attributed peak potentials measured decreased linearly with decreasing temperatures. Increasing the MgO-concentration led to more negative peak potentials. Introducing alumina in the melt first resulted in less negative peak potentials. If the molar Al₂O₃-concentration is equal to that of Na₂O (=10 mol%) the peak potentials are least negative. Further increase of the Al₂O₃-concentration led to more negative peak potentials. The variation of the Na₂O-concentration led to a maximum in the peak potentials at an Na₂O-concentration of 10 mol%. An empirical formula which allows the calculation of standard potentials from the chemical composition is proposed. Furthermore, a structural explanation for the effect of the chemical composition is given. Especially, the incorporation of Al₂O₃ as AlO₄⁻-tetrahedra at [Al₂O₃] < [Na₂O] and as network modifier at larger concentrations was structurally explained by the similarities of Fe²⁺ and Mg²⁺, with respect to cation radii and metal–oxygen bond lengths.     

Structural and thermal properties of some tellurite glasses

Tellurium oxide glasses were prepared by the hammer and anvil technique. The glass systems are (0.85TeO₂ + 0.15Z), where Z = K₂O, TiO₂, V₂O₅, MnO, Fe₂O₃, CoO, NiO or CuO. A second group is a ternary system 0.85TeO₂+(0.15 − x)TiO₂ + xFe₂O₃) with x=0.0, 0.05, 0.1, 0.15 mol. X-ray diffraction, infrared spectroscopy and differential thermal analysis measurements were carried out. The present study showed the different glass-forming groups, the glass transition and crystallization temperatures as well as the crystallization processes.     

The vanadyl ion as a spectroscopic probe:: Measurement of optical basicity in the visible / near-infrared region

Previously optical basicity was always measured using s-p absorption spectra of Tl⁺, Pb²⁺ and Bi³⁺, but since these spectra are in the UV region, media containing oxides of transition metal aons have been excluded from such measurements. The present work shows that for VO²⁺ the d-d transition ²B₂ → ²E red-shifts with increasing optical basicity, and a study in the Na₂O---P₂O₅ glass system allows comparison with results obtained previously with Tl⁺ and other probe ions. It is shown that under controlled conditions determination of optical basicity with VO²⁺ is viable, and since the ²B₂ → ²E spectral band occurs in the visible / near-IR region, UV transparency of the medium is no longer necessary. The VO²⁺ probe therefore offers a means of obtaining optical basicities of glasses containing e.g. PbO, or of metallurgica slags containing e.g. Fe₂O₃ or MnO.     

Structure and magnetic properties of lead vanadate glasses

X-ray photoelectron spectroscopy (XPS) has been used to obtain structural information on the xPbO · (1−x)V₂O₅ glass system where x=0.22, 0.35, 0.43, and 0.54. The binding energies from the Pb 4f_7/2 and Pb 4f_5/2 core levels decrease with increasing PbO content while the full-width at half-maximum of these peaks increase. The O 1s spectra show an asymmetry for samples having composition x<0.5, which results from oxygen atoms in the V–O–V configuration (bridging oxygens) and from oxygen atoms in the V–O–Pb and Pb–O–Pb configurations (non-bridging oxygens). The number of non-bridging oxygens was found to increase from 81% to 92% with increasing PbO content. For x=0.54, the O 1s spectrum was symmetric indicating that all three oxygen configurations have essentially the same binding energy. This behavior in addition to the decreasing binding energies of the Pb 4f levels with increasing PbO content suggest that the Pb–O bonds are becoming more covalent in nature and that eventually PbO changed its role from a glass modifier to a glass former for x>0.5. The asymmetric V 2p_3/2 peaks for the x<0.4 glasses indicate the presence of a small concentration of V⁴⁺ ions in addition to V⁵⁺ ions, while the symmetric V 2p_3/2 peaks for the more concentrated PbO vanadate glasses indicate only V⁵⁺ being present. The concentration of V⁴⁺ ions (0–4%) from the XPS data is consistent with determinations from magnetic susceptibility measurements on the same glass samples. In addition to the paramagnetic contribution (Curie–Weiss temperature-dependent behavior) from the V⁴⁺ ions, the susceptibility for these oxide glasses consisted of a positive, constant contribution arising from the temperature-independent paramagnetic V₂O₅ exceeding the diamagnetism from the core ions.     

Investigations of g-value correlations associated with the g = 4.3 ESR signal of Fe in glass

The g = 4.3 ESR signal of Fe³⁺ in glass is usually attributed to a “fully rhombic” distortion characterized by E = D/3, where E and D are the splitting constants belonging to the second-order rhombic and axial terms, respectively, of the crystal-field interaction. An alternate statistical approach to the origin of this signal has been given by Peterson et al. on the basis of axial symmetry and broad overlapping distribution of g_| and g that are correlated in opposition (negatively) resulting in spiking at g 4.3. The present paper reports detailed computer studies of the distribution of effective g value produced by large variations in both D and E to test whether negative g-value correlations leading to spiking at g 4.3 are generable from site dependent fluctuations in the second-order crystal-field terms. It is found that the ESR line arising from the middle Kramer's doublet in the fully rhombic limit (E → D/3, |D| > hν) uniquely generates the negative g-value correlation required for spiking at g 4.3.     

B NMR investigations in xV2O5–B2O3 and xV2O5–B2O3–PbO glasses

11B (I=3/2) MAS NMR in the binary glass system xV₂O₅–B₂O₃ (x=0.053, 0.43) and the ternary glass system xV₂O₅–B₂O₃–PbO (0.1x1.5) has been investigated at room temperature. In the xV₂O₅–B₂O₃ glasses, one NMR line due to BO₃ unit was observed. Meanwhile in the xV₂O₅–B₂O₃–PbO, two NMR lines which arise from BO₃ and BO₄ units were detected, where the appearance of BO₄ units is produced by the presence of PbO. From the computer-simulation of the ¹¹B NMR central transition line (m=−1/2↔1/2), the quadrupole parameters (e²qQ/h and η) for BO₃ units in xV₂O₅–B₂O₃, and those for BO₃ and BO₄ units in xV₂O₅–B₂O₃–PbO were obtained as a function of x. As the V₂O₅ content increases in xV₂O₅–B₂O₃–PbO, the e²qQ/h and η values of the BO₃⁻ associated resonance are found to slightly decrease and increase, respectively. Meanwhile, the e²qQ/h and η values of BO₄⁻ associated resonance in xV₂O₅–B₂O₃–PbO are found to slightly increase and decrease, respectively. By comparing the intensities of the total transitions (m=−3/2↔−1/2,m=−1/2↔1/2, and 1/2↔3/2) for the ¹¹B NMR line of BO₃ and BO₄ units contained in xV₂O₅–B₂O₃–PbO with those of respective standard samples of 0.053V₂O₅–B₂O₃ and NaBH₄, the quantitative fractions of BO₃ and BO₄ in xV₂O₅–B₂O₃–PbO were obtained as a function of x.     

Electronic traps in mixed Si1−xGexO2 films

Thermally stimulated luminescence (TSL) and infrared (IR) spectroscopy were measured in plasma grown Si_1−xGe_xO₂ (x=0, 0.08, 0.15, 0.25, 0.5) with different thicknesses (12–40 nm). A comparison with the TSL properties of thermally grown SiO₂ and GeO₂ was also performed. A main IR absorption structure was detected, due to the superposition of the peaks related to the asymmetric O stretching modes of (i) Si–O–Si (at ≈1060 cm⁻¹) and (ii) Si–O–Ge (at 1001 cm⁻¹). Another peak at ≈860 cm⁻¹ was observed only for Ge concentrations, x>0.15, corresponding to the asymmetric O stretching mode in Ge–O–Ge bonds. A TSL peak was observed at 70°C, and a smaller structure at around 200°C. The 70°C peak was more intense in all Ge rich layers than in plasma grown SiO₂. Based on the thickness dependence of the signal intensity we propose that at Ge concentrations 0.25x0.5 TSL active defects are localised at interfacial regions (oxide/semiconductor, Ge poor/Ge rich internal interface, oxide external surface/atmosphere). Based on similarities between TSL glow curves in plasma grown Si_1−xGe_xO₂, thermally grown GeO₂ and SiO₂ we propose that oxygen vacancy related defects are trapping states in Si_1−xGe_xO₂ and GeO₂.     

ESR and Mössbauer studies of dispersed states of Fe ions in silica gels

0.01Fe₂O₃---0.99SiO₂ gels were prepared by three different sol-gel methods and the effects of the heat-treatment temperature of the gels on the ESR and Mössbauer parameters were investigated to obtain information about the change in the state of iron ions in the gel. All the gels were found to be amorphous under 600 °C, and among these three methods, the best dispersed state of Fe³⁺ ions was obtained by the method where TEOS was partially hydrolyzed with the same mole content of water before the addition of Fe(OEt)₃. It was indicated that the reaction at the sol-stage plays an important role in the degree of dispersal of Fe³⁺ ions in this system.     

New solvents for the growth of substituted BaFe12O19 single crystals from high-temperature solutions

The solubility of a series of hexaferrite derivatives of BaFe₁₂O₁₉ in solvents of the system Na₂O-B₂O₃ with oxide ratios of 7:3 and 3:2 has been investigated. The temperature dependences of the saturation concentration in these solvents are determined for ferrites with the nominal compositions Ba_0.8Pb_0.2Fe₁₂O₁₉, BaFe₁₀Ga₂O₁₉, BaFe₁₀Al₂O₁₉ and BaFe₈Mn₂ Ti₂O₁₉. Single crystals of BaFe₁₂O₁₉, in which part of the metal ions are replaced by various amounts of Pb²⁺, Ga³⁺, Al³⁺ and Mn²⁺ + Ti⁴⁺ ions, are g rown from the solutions by the slow cooling technique. The distribution coefficients of the substituting ions and the compositions of the crystals obtained are established by microprobe analysis (EPMA). Information on the position of substitution is obtained from the Mössbauer spectra.     

Study of electrical properties of MoO3–Fe2O3–P2O5 and SrO–Fe2O3–P2O5 glasses by impedance spectroscopy. II

The electrical and dielectric properties for three series of MoO₃–Fe₂O₃–P₂O₅ and one series of SrO–Fe₂O₃–P₂O₅ glasses were measured by impedance spectroscopy in the frequency range from 0.01 Hz to 3 MHz and over the temperature range from 303 to 473 K. It was shown in Part I that the MoO₃ is incorporated into phosphate network and the structure/properties are strongly influenced by the overall O/P ratio. The Fe₂O₃ content and Fe(II)/Fe_tot ratio in these glasses have significant effects on the electrical conductivity and dielectric permittivity. With decreasing Fe₂O₃ content in MoO₃–Fe₂O₃–P₂O₅ glasses with O/P at 3.5 the dc conductivity, σ_dc(ω) decreases for two orders of magnitude, which indicates that the conductivity for these glasses depends on Fe₂O₃ and is independent of the MoO₃ content. Also, the dielectric properties such as ^′(ω), ^″(ω) and σ_ac(ω) and their variation with frequency and temperature indicates a decrease in relaxation intensity with increase in the concentration of MoO₃. On the other hand, the dc conductivity for MoO₃–Fe₂O₃–P₂O₅ glasses with O/P > 3.5 increases with the substitution of MoO₃ which has been explained by an increase in the number of non-bridging oxygens and formation of Fe–O–P bonds that are responsible for formation of small polarons. The increase in the dielectric permittivity, ^′(ω) with increasing MoO₃ content is attributed to the increase in the deformation of glass network with increasing bonding defects. For SrO–Fe₂O₃–P₂O₅ glasses the conductivity and dielectric permittivity remained constant with increasing SrO.     

铁离子掺杂对铜铬黑颜料呈色性能的影响

为改善CuCr₂O₄黑色颜料呈色性能,将Fe³⁺掺杂进入CuCr₂O₄晶体中,采用共沉淀法制备CuCr_2-xFe_xO₄(x=0,0.04,0.05,0.06,0.07),并对所制备样品进行TG-DTA、XRD、SEM、Raman、XPS、UV-Vis吸收光谱和色度值的测试与表征。结果表明,Fe以三价态固溶进入Cr³⁺位置,未出现杂质相,得到的CuCr_2-xFe_xO₄晶粒细小、分散均匀。Fe³⁺掺杂可减小CuCr₂O₄的禁带宽度,从1.25 eV减小到1.08 eV,禁带宽度的减小是由于2p(O^2-)→3d(Fe³⁺)和Fe³⁺的d-d(⁶A_1g→⁴T_1g和 ⁶A_1g→⁴T_2g)电荷跃迁引起的。禁带宽度的减小使得黑色颜料对可见光(380~780 nm)的吸收率提高,L^*值减小,呈现出良好的黑度。得到的最佳黑色颜料为CuCr_1.95Fe_0.05O₄,L^*=17.63,a^*=-0.77,b^*=-1.61。     

Chemical diffusion and crystalline nucleation during oxidation of ferrous iron-bearing magnesium aluminosilicate glass

Rutherford backscattering spectroscopy (RBS) and transmission electron microscopy (TEM) have been used to evaluate the mechanism and kinetics of oxidation of a Fe²⁺-doped MgO---Al₂O₃---SiO₂ glass (with nominal composition along the enstatite-cordierite-liquid divariant) which was heat treated in air under the time and temperature ranges 10–150 h and 700–800°C, respectively. The results clearly demonstrate that oxidation occurs by a cation diffusion process: specifically, the divalent cations diffuse from the interior of the glass to the free surface where they subsequently react with environmental oxygen to form a two-phase, MgO---(Mg, Fe)₃O₄ crystalline layer which covers the (divalent cation-depleted) glass. Oxidation of some Fe²⁺ within the glass occurs via the inward flux of electron holes (a counterflux to the divalent cation diffusion required to maintain charge neutrality of the glass); this internal oxidation results in the fine-scale ( 1–5 nm), homogeneous nucleation of crystalline (Mg, Fe)₃O₄ within the divalent cation-depleted layer of the glass. Chemical diffusion of an oxygen species is thus demonstrated to be a slower, parallel kinetic process which is not required for oxidation to occur in this material. A first-order analysis of oxidation kinetics in the glass is presented.     

Mössbauer studies on some glasses and crystals in the Na2O---Fe2O3---SiO2 system

Mössbauer absorption measurements have been made at room temperature on ⁵⁷Fe in iron sodium silicate glasses containing 3–15 mol% Fe₂O₃ and various iron alkali silicate crystals in order to study the state of iron in these glasses. The spectra of all the glasses gave one doublet with a quadrupole splitting varying from 0.73–0.78 mm s⁻¹, while those of Na₂O · Fe₂O₃ · 4 SiO₂ and 5 Na₂O · Fe₂O₃ · 8 SiO₂ crystals showed much smaller quadrupole splitting, 0.28 mm s⁻¹ and 0.10 mm s⁻¹, respectively, and an asymmetrical doublet of much narrower linewidth. When sodium was replaced by other alkali metals of larger size, such as K and Cs, in MFeSi₂O₆ and MFeSi₃O₈ crystals, the quadrupole splitting became wider and approached to 0.73 mm s⁻¹. Such a variation was not observed for glasses. These results suggest that a larger number of non-identical sites exist in iron sodium silicate glasses than in the corresponding crystals.     

Homogeneous line width in a zinc borate glass activated by Eu

In this work we report on the temperature depedence of the homogeneous line width (Γ_h) in 4ZnO · 3B₂O₃:Eu³⁺ glass in the region between 30 K and room temperature. The time resolved resonant fluorescence line narrowing technique was applied to the ⁷F₀ ↔ ⁵D₀ transition of Eu³⁺. We obtain that Γ_h follows the commonly found behaviour T² in the whole range of temperature (30–300 K). The Γ_h is comparable to that measured in borate glasses with a small amount of network modifier. This result, together with a linear increase of Γ_h with the excitation energy within the inhomogeneous profile, is indicative of a specific local environment around the Eu³⁺ ion in the zinc borate glass.     

Sr7Sb2O12∶Dy3+荧光粉的制备及其发光性能

采用高温固相法制备了一系列新型Sr_7-xSb₂O₁₂∶xDy³⁺(x=0~0.35)(摩尔分数)荧光粉,并研究了Sr_7-xSb₂O₁₂∶xDy³⁺的物相结构、发光性能、热稳定性以及荧光寿命。在350 nm光激发下,Sr_7-xSb₂O₁₂∶xDy³⁺可以检测到中心波长在482 nm处的蓝光发射带和中心波长在576 nm处的黄光发射带,当x=0.056时,Dy³⁺浓度猝灭,Sr_6.944Sb₂O₁₂∶0.056Dy³⁺ CIE色坐标为(0.340 8,0.349 3),猝灭机理归因于电偶极-电偶极相互作用。当x=0.14时,该荧光粉可以发出色坐标为(0.310 9,0.314 0)的白光。此外,Sr_7-xSb₂O₁₂∶xDy³⁺在453 K的发光强度大约为室温下发光强度的83.3%,表现出良好的热稳定性。综合以上研究结果表明,Sr_7-xSb₂O₁₂∶xDy³⁺有望用于紫外光激发的白光发光二极管器件中。     

Study of PbO films on sodium borate glasses part II: Formation of interdiffusion layers at the glass surface

By selecting carefully controlled conditions for the thermal treatment of sodium borate glasses coated with PbO films, it is possible to prevent Pb²⁺ ions from penetrating deeply into the glass. For low alkali glasses, an interdiffusion layer can be formed, which sub-surface cation profiling (by ion beam induced radiation) shows is a solid solution of Na₂O and B₂O₃ in PbO which acts as solvent. Experiments with 18.0 mol-% Na₂O glass show that it is possible to transform such an interdiffusion layer into a second type in which Na₂O and B₂O₃ together act as solvent and the concentration of PbO solute varies through the layer. For both types of layer the Na₂O : B₂O₃ ratio is different from that of the glass substrate, and for the production of the second type of layer it is shown that an important factor connected with penetration of PbO into the glass surface is a “sweating” process in which thermal treatment of the glass, even in the absence of PbO, results in migration of Na⁺ ions so that the glass surface has a Na₂O content higher than that of the bulk glass. Changes in the UV spectra of the Pb²⁺ ion are correlated with the formation of the interdiffusion layers, and results show that types of layer have optical basicities significantly greater than that of the glass substrate, through either the high PbO or high Na₂O content.