The measurement of gas diffusivity in porous materials by temporal analysis of products (TAP)

The pulsing of argon in a temporal analysis of products (TAP) reactor and reactor modeling of the response curves were used to measure the effective intraparticle diffusivities in porous materials. The diffusivity that can be measured is limited: (1) at the low end by intraparticle diffusion being too slow such that just a small fraction of the pulse gets into the pores to give an indistinguishable tail, which only measures that the diffusivity is smaller than an upper limit and (2) at the high end by intraparticle diffusion being too fast such that it gives a constant concentration in the pores, which only measures that the diffusivity is larger than a lower limit. The limits and range are slightly different for different particle and bed dimensions. A 9 mm long packed bed has a sensitive range of about 300-fold where there are discernible changes in the normalized pulse shape due to diffusivity changes. If small particles of about 50 μm are used, the range is from 1 × 10⁻¹⁰ to 3 × 10⁻⁸ m²/s, and if large particles of about 500 μm are used, the range is from 2 × 10⁻⁹to 5 × 10⁻⁷ m²/s.     

Selective permeation and separation of steam from water–methanol–hydrogen gas mixtures through mordenite membrane

Separation properties of a mordenite membrane for water–methanol–hydrogen mixtures were studied in the temperature range from 423 to 523 K under pressurized conditions. The mordenite membrane was prepared on the outer surface of a porous alumina tubular support by a secondary-growth method. It was found that water was selectively permeated through the membrane. The separation factor of water/hydrogen and water/methanol were 49–156 and 73–101, respectively. Even when only hydrogen was fed at 0.5 MPa, its permeance was as low as 10⁻⁹ mol m⁻² s⁻¹ Pa⁻¹ up to 493 K, possibly suggesting that water pre-adsorbed in the micropores of mordenite hindered the permeation of hydrogen. The hydrogen permeance dramatically increased to 6.5 × 10⁻⁷ mol m⁻² s⁻¹ Pa⁻¹ at 503 K and reached to 1.4 × 10⁻⁶ mol m⁻² s⁻¹ Pa⁻¹ at 523 K because of the formation of cracks in the membrane. However, the membrane was thermally stabilized in the presence of steam and/or methanol.     

Reduction of nitrite by sulfamic acid and sodium azide from aqueous solutions treated by gliding arc discharge

Nitrous and nitric acids form in aqueous solutions exposed to a gliding arc discharge burning in humid air. The anions interfere when the concentration of particular solutes such as pollutants must be determined. In particular they falsify the COD measurements and spectral investigations and thus the efficiency of the plasma treatment in pollutant abatement. The nitrite anions must be thus removed, which require specific reagents. The influence of parameters such as solution pH and [reducers]/[NO₂⁻] ratio on the reduction reaction was evaluated. The reduction of nitrite into N₂ either by sulfamic acid or sodium azide is a first-order pH-dependant reaction with regard to nitrite and reducers (k₁ = 2.93 × 10⁻¹ m³ kmol⁻¹ s⁻¹; k₂ = 6.21 × 10⁻¹ m³ kmol⁻¹ s⁻¹, respectively). Sodium azide is thus more reactive than sulfamic acid.     

Poly-(3-methylthiophene)/carbon nanotubes hybrid composite-modified electrodes

The preparation of poly-(3-methylthiophene)—multi-walled carbon nanotubes hybrid composite electrodes is reported. The hybrid electrode shows a synergic effect of the electrocatalytic properties, and high active surface area of both the conducting polymer and carbon nanotubes, which gives rise to a remarkable improvement of oxidation of NADH with respect to polymer-modified electrodes, and CNTs-modified electrodes. SEM showed that carbon nanotubes served as nanosized backbone for P3MT electropolymerization. The amperometric NADH detection at +300 mV provided fast responses, a range of linearity between 5.0 × 10⁻⁷ and 2.0 × 10⁻⁵ mol l⁻¹, and a detection limit of 1.7 × 10⁻⁷ mol l⁻¹, which compares advantageously with those reported for other NADH CNT-based amperometric sensors. Furthermore, the direct electrochemistry of cytochrome c and FAD at the hybrid electrode is also checked.     

Catalyzing a cycloaddition with molecularly imprinted polymers obtained via immobilized templates

Polymeric catalysts to be applied in the Diels–Alder cycloaddition of hexachlorocyclopentadiene and maleic acid have been prepared via molecular imprinting with template molecules immobilized on silica particles. These enzyme mimicking polymers exhibit specific catalytic effects compared to non-imprinted control polymers or polymer-free solutions. It could be demonstrated that the activity of the molecularly imprinted material rises when increasing the temperature. By this means, the reduction of the activation energy (as expected for catalysts) from 63 to 55 kJ mol⁻¹ could be observed. Furthermore, the reaction was characterized based on the Michaelis–Menten model. For the diene compound a Michaelis constant of K_M=5.8 mmol l⁻¹ and an effective reaction rate of r_max,eff=0.4 μmol l⁻¹ s⁻¹, leading to a reaction rate constant k_eff=1.1×10⁻³ s⁻¹, were determined.     

Pyrylium salt-photosensitised degradation of phenolic contaminants present in olive oil wastewaters with solar light: Part II. Benzoic acid derivatives

Solar light photodegradation, catalysed by a pyrylium salt, of seven benzoic acids present in olive oil mill, has been studied. Significant percentages of photodegradation (20–40%) have been achieved after 6 h of solar exposure for six of the acids, even though they were expected to be difficult to oxidise, due to the presence of an electron-withdrawing carboxylic acid group directly attached to the aromatic ring. Quenching constants for the electron-transfer process between the substrate and the excited catalyst were calculated by means of fluorescence measurements for syringic acid (66×10⁹ M⁻¹ s⁻¹), gallic acid (51×10⁹ M⁻¹ s⁻¹), veratric acid (51×10⁹ M⁻¹ s⁻¹), vanillic acid (48×10⁹ M⁻¹ s⁻¹), protocatechuic acid (37×10⁹ M⁻¹ s⁻¹) and p-hydroxybenzoic acid (15×10⁹ M⁻¹ s⁻¹); no quenching was found for benzoic acid. These photophysical measurements are in good correlation with the yields obtained in the pyrylium salt photocatalysed degradation of those phenolic acids.     

On-stream modification of MFI zeolite membranes for enhancing hydrogen separation at high temperature

-Alumina-supported MFI zeolite membranes were modified by on-stream catalytic thermal cracking of methyldiethoxysilane (MDES) molecules inside the zeolitic channels during the separation of H₂/CO₂ gas mixture at 450 °C and atmospheric pressure. The MDES vapor was carried by the H₂/CO₂ feed gas and the effect of modification was monitored continuously through online analysis of the permeate stream. The modified membrane exhibited a significant increase in H₂ selectivity over CO₂ with a moderate decrease in H₂ permeance. At 450 °C, the modified MFI membrane obtained a H₂/CO₂ permselectivity of 17.5 with H₂ single gas permeance of 1.86 × 10⁻⁷ mol m⁻² s⁻¹ Pa⁻¹ as compared to a permselectivity of 2.78 and permeance of 2.75 × 10⁻⁷ mol m⁻² s⁻¹ Pa⁻¹ for the membrane before modification. The modified membrane also showed good performance and stability in separation of H₂/CO₂ gas mixture containing up to 28.4% water vapor at 450 °C and atmospheric pressure.     

Dilute solution properties of carboxymethylchitins in high ionic-strength solvent

The hydrodynamic characteristics in aqueous solution at ionic strength I=0.2  of carboxymethylchitins of different degrees of chemical substitution have been determined. Experimental values varied over the following ranges: the translational diffusion coefficient (at 25.0°C), 1.1<10⁷×D<2.9 cm² s⁻¹; the sedimentation coefficient, 2.4<s<5.0 S; the Gralen coefficient (sedimentation concentration-dependence parameter), 130<k_s<680 mL g⁻¹; the intrinsic viscosity, 130<[η]<550 mL g⁻¹. Combination of s with D using the Svedberg equation yielded ‘sedimentation–diffusion' molecular weights in the range 40 000<M<240 000 g mol⁻¹. The corresponding Mark–Houwink–Kuhn–Sakurada (MHKS) relationships between the molecular weight and s, D and [η] were: [η]=5.58×10⁻³ M^0.94; D=1.87×10⁻⁴ M^−0.60; s=4.10×10⁻¹⁵ M^0.39. The equilibrium rigidity and hydrodynamic diameter of the carboxymethylchitin polymer chain is also investigated on the basis of wormlike coil theory without excluded volume effects. The significance of the Gralen k_s values for these substances is discussed.     

Effect of Pt on the water resistance of Co-zeolites upon the SCR of NOx with CH4

The objective of this work was to study the promotional effect of Pt on Co-zeolite (viz. mordenite, ferrierite, ZSM-5 and Y-zeolite) and Co/Al₂O₃ on the selective catalytic reduction (SCR) of NO_x with CH₄ under dry and wet reaction stream. After being reduced in H₂ at 350°C, the PtCo bimetallic zeolites showed higher NO to N₂ conversion and selectivity than the monometallic samples, as well as a combination of the latter samples such as mechanical mixtures or two-stage catalysts. After the same pretreatment, under wet reaction stream, the bimetallic samples were also more active. Among the other catalysts studied with 5% of water in the feed, (NO = CH₄ = 1000 ppm, O₂ = 2%), the NO conversion dropped to zero over Co_2.0Mor at 500°C and GHSV = 30,000 h⁻¹, whereas it is 20% in Pt_0.5Co_2.0Mor. In Pt/Co/Al₂O₃ the NO_x conversion dropped below 5% with only 2% of water under the same reaction conditions. The specific activity given as molecules of NO converted per total metal atom per second were 16.5 × 10⁻⁴ s⁻¹ for Pt_0.5Co_2.0Fer, 13 × 10⁻⁴ s⁻¹ for Pt_0.5Co_2.0Mor, 4.33 × 10⁻⁴ s⁻¹ for Pt_0.5Co_2.0ZSM-5 and 0.5 × 10⁻⁴ s⁻¹ for Pt/Co/Al₂O₃. The Y-zeolite-based samples were inactive in both mono and bimetallic samples. The species initially present in the solid were Pt° and Co°, together with Co²⁺ and Pt²⁺ at exchange positions. Co° seems not to participate as an active site in the SCR of NO_x. Those species remained after the reaction but some reorganization occurred. A synergetic effect among the different species that enhances both the NO to NO₂ reaction, the activation of CH₄ and also the ability of the catalyst to adsorb NO, could be responsible for the high activity and selectivity of the bimetallic zeolites.     

High-quality, oriented and mesostructured organosilica monolith as a potential UV sensor

We synthesized high-quality and oriented periodic mesoporous organosilica (PMO) monoliths through a solvent evaporation process using a wide range of mole ratios of the components: 0.17–0.56 1,2-bis(triethoxysilyl)ethane (BTSE): 0.2 cetyltrimethylammonium chloride (CTACl): 0–1.8 × 10⁻³ HCl: 0–80 EtOH: 5–400 H₂O. X-ray diffraction (XRD) patterns and transmission electron microscopy (TEM) images indicated that the mesoporous channels within the monolith samples were oriented parallel to the flat external surface of the PMO monolith and possessed a hexagonal symmetry lattice (p6mm). The PMO monolith synthesized from a reactant composition of 0.35 BTSE: 0.2 CTACl: 1.8 × 10⁻⁶ HCl: 10 EtOH: 10 H₂O had a pore diameter, pore volume, and surface area – obtained from an N₂ sorption isotherm – of 25.0 Å, 0.96 cm³ g⁻¹ and 1231 m² g⁻¹, respectively. After calcination at 280 °C for 2 h in N₂ flow, the PMO monolith retained monolith-shape and mesostructure. Pore diameter and surface area of the calcined PMO monolith sample were 19.8 Å, 0.53 cm³ g⁻¹ and 1368 m² g⁻¹, respectively. We performed ²⁹Si and ¹³C CP MAS NMR spectroscopy experiments to confirm the presence of Si–C bonding within the framework of the PMO monoliths. We investigated the thermal stability of the PMO monoliths through thermogravimetric analysis (TGA). In addition, rare-earth ions (Eu³⁺, Tb³⁺ and Tm³⁺) were doped into the monoliths. Optical properties of those Eu³⁺, Tb³⁺ and Tm³⁺-doped PMO monoliths were investigated by photoluminescence (PL) spectra to evaluate their potential applicability as UV sensors.     

Kinetics and mechanism of low-temperature ozone decomposition by Co-ions adsorbed on silica

Kinetics and mechanism of low-temperature ozone ((5–50) × 10⁻³ mol/m³ in the gas–air mixture) decomposition by Co-catalysts supported on silica have been studied. Co-ions adsorbed on silica react with surface oxygen species, thus resulting in an active catalyst. Low concentrations of Co-ions form a monolayer on the surface. Their specific catalytic activity remained constant, but sharply decreased at higher concentrations due to a formation of polynuclear Co-complexes. Ozone decomposition may occur either as a stoichiometric or catalytic process, depending on the ozone and catalyst concentrations. The turnover number increases with ozone concentration reaching a saturation point. It also increases with Co-concentration in the beginning, but drops at a concentration >1 × 10⁻⁴ mol/g. The mechanism of the reaction is discussed.     

Adsorption and diffusion of light alkanes on nanoporous faujasite catalysts investigated by molecular dynamics simulations

Molecular dynamics simulations were performed for ethane, propane, and n-butane in siliceous faujasite for different numbers of molecules per unit cell (loadings) at 300 K. Both the adsorbed molecules and the zeolite framework were modeled as flexible entities. A new semiempirical analytical potential function for the systems was constructed. From the mean-square displacement of the molecules, self-diffusion coefficients of 18.7 × 10⁻⁵, 13.3 × 10⁻⁵, and 4.3 × 10⁻⁵ cm²/s were calculated for ethane, propane, and n-butane, respectively at a loading of 8 molecules/unit cell. They compare well with experimental values from pulsed-field gradient NMR measurements (10 × 10⁻⁵, 9 × 10⁻⁵, and 6 × 10⁻⁵ cm²/s, respectively). Besides depending on the size of the hydrocarbon, the heats of adsorption and self-diffusion coefficients also strongly depend on the loading of adsorbate molecules. The results suggest that the new intermolecular force field can reasonably describe the adsorption and diffusion behavior of ethane, propane, and n-butane in faujasite zeolite.     

High flux mesoporous MCM-48 membranes: Effects of support and synthesis conditions on membrane permeance and quality

This communication reports experimental efforts to synthesize defect-free mesoporous MCM-48 membranes with improved gas flux. We demonstrate a facile and inexpensive method of synthesizing defect-free supported MCM-48 membranes with improved N₂ and CO₂ permeance (>2 × 10⁻⁷ mol/m² s Pa) employing asymmetric supports for the membrane synthesis which contain layers of macropores possessing different pore sizes. The membranes prepared on asymmetric -alumina supports displayed higher gas permeance than those fabricated on symmetric supports (N₂ permeance <10⁻⁷ mol/m² s Pa) as confirmed by unsteady-state gas permeation experiments. Further improvement in gas permeance was achieved by covering one face and the sides of the support with a ceramic tape during membrane synthesis.     

Liquid-phase methanol synthesis in apolar (squalane) and polar (tetraethylene glycol dimethylether) solvents

The kinetics of the three-phase methanol synthesis over a commercial Cu–Zn–Al₂O₃ catalyst were studied in an apolar solvent, squalane and a polar solvent, tetraethylene glycol dimethylether (TEGDME). Experimental conditions were varied as follows: P=3.0–5.3 MPa, T=488–533 K and Φ_vG/w=7.5×10⁻³–8×10⁻³ Nm³ s⁻¹kg⁻¹_cat. The nature of the slurry–liquid influences the activation energy and the kinetic rate constant by interaction between adsorbed species and solvent and by competitive adsorption of the solvent on the catalyst surface. The rate of reaction to methanol observed in TEGDME appeared to be about 10 times lower than in squalane. TEGDME reduces the reaction rate, which is a disadvantage for its use as a solvent.     

Electrodeposition of cesium at mercury electrodes in the tri-1-butylmethylammonium bis((trifluoromethyl)sulfonyl)imide room-temperature ionic liquid

The electrochemistry of cesium was investigated at mercury electrodes in the tri-1-butylmethylammonium bis((trifluoromethyl)sulfonyl)imide (Bu₃MeN⁺Tf₂N⁻) room-temperature ionic liquid (RTIL) by using cyclic staircase voltammetry, rotating disk electrode voltammetry, and chronoamperometry. The reduction of cesium ions at mercury exhibits quasireversible behavior with k⁰ = 9.8 × 10⁻⁵ cm s⁻¹ and = 0.36. The diffusion coefficient of Cs⁺ in this RTIL was 1.04 × 10⁻⁸ cm² s⁻¹ at 303 K. Bulk deposition/stripping experiments conducted at a rotating mercury film electrode gave an average recovery of 97% of the electrodeposited Cs. The density, absolute viscosity, and equivalent conductance of Bu₃MeN⁺Tf₂N⁻ were measured over the range of temperatures from 298 to 353 K. A polynomial equation describing the temperature dependence of the density is presented. Both the viscosity and conductance exhibited the non-Arrhenius temperature dependence typical of glass-forming liquids. The ideal glass transition temperature and the activation energies for viscosity and conductance were obtained by fitting the Vogel–Tammann–Fulcher (VTF) equation to the experimental data for these transport properties.     

Effects of oxygen concentration on the electrical properties of ZnO films

In this paper, electrical characteristics by various oxygen content in ZnO films were studied. To control the oxygen content of ZnO films, post-thermal annealing was performed in N₂ and air ambient, led to improve crystallinity and optical properties of ZnO films. The oxygen concentration was measured by Auger electron spectroscopy. The ZnO films having the deficiency of oxygen showed the electron concentrations between 10²¹ and mid 6 × 10¹⁷ cm⁻³ and resistivity at 10⁻³–10⁻¹ Ω cm. On the other hand, when the oxygen concentration of the ZnO films was up to the stoichiometry with Zn, the ZnO films showed low electron concentration at −10¹⁷ cm⁻³ and resistivity at 10 Ω cm.     

Decomposition of NO over Cu-AITS-1 zeolites

H-AITS-1 zeolite with Si/Ti = 50 and Si/Al = 50 was employed in preparing catalyst samples by ion-exchange and impregnation with a copper nitrate solution to obtain 0.24–1.15 wt.% and 1.5, 2 and 2.5 wt.% Cu loading, respectively. The catalytic properties for the NO decomposition were compared with that of Cu-ZSM-5 (Si/Al = 25 with 2 wt.% Cu loading) and similarity was found between the AITS-1 based samples and Cu-ZSM-5. Due to the higher acidity, the activity at 500°C per total copper atoms (an apparent turnover frequency, TOF) was significantly higher over Cu based AITS-1 samples being 2–3 × 10⁻³ s⁻¹ as compared to 1 × 10⁻³ s⁻¹ measured on Cu-ZSM-5. For the ion-exchanged Cu-AITS-1 there was an increase in TOF with increasing copper content, whereas on the impregnated samples a decrease in TOF was found. On all catalysts there was a maximum in the NO conversion at 500–550°C. The amount of NO per copper atom measured by temperature programmed desorption (TPD) was about the same as that on Cu-ZSM-5 and the features of the TPD were also similar. At the first contact of the catalyst at 500°C with the 2 vol% NO/Ar gas a transient N₂O formation and a considerable delay in the O₂ formation was observed. This could, however, be reproduced only on fresh catalyst, while all further transients showed different but reproducible features using the same sample.     

New polyaniline(PAni)-polyelectrolyte (PDDMAC) composites: Synthesis and applications

Conducting and electroactive polymer blends of polyaniline (PAni) with polyelectrolyte, poly(diallydimethylammoniumchloride) (PDDMAC) have been synthesized by an in situ polymerization method and the resulting composites have been characterized by FT-IR, UV–Vis, XRD, AFM and electrochemical techniques. The blends are conducting and electroactive with even lower loadings of PAni and can be cast as films. The conductivity of the cast films containing 0.04–1.5 wt% PAni ranged from 4.5 × 10⁻⁶ to 42 × 10⁻⁶ S/cm. Some of the composites are tested for their corrosion inhibition property for pure iron in 1 M HCl solutions and were found to be active inhibitors.     

Kaolinite, montmorillonite, and their modified derivatives as adsorbents for removal of Cu(II) from aqueous solution

Adsorption of metals by clay minerals is a complex process controlled by a number of environmental variables. The present work investigates the removal of Cu(II) ions from an aqueous solution by kaolinite, montmorillonite, and their poly(oxo zirconium) and tetrabutylammonium derivatives. The entry of ZrO and TBA into the layers of both kaolinite and montmorillonite was confirmed by XRD measurement. The specific surface areas of kaolinite, ZrO-kaolinite, TBA-kaolinite, montmorillonite, ZrO-montmorillonite, TBA-montmorillonite were 3.8, 13.4, 14.0, 19.8, 35.8 and 42.2 m²/g, respectively. The cation exchange capacity (CEC) was measured as 11.3, 10.2, 3.9, 153.0, 73.2 and 47.6 meq/100 g for kaolinite, ZrO-kaolinite, TBA-kaolinite, montmorillonite, ZrO-montmorillonite, TBA-montmorillonite, respectively. Adsorption increased with pH till Cu(II) ions became insoluble in alkaline medium. The kinetics of the interactions suggests that the interactions could be best represented by a mechanism based on second order kinetics (k₂ = 7.7 × 10⁻² to 15.4 × 10⁻² g mg⁻¹ min⁻¹). The adsorption followed Langmuir isotherm model with monolayer adsorption capacity of 3.0–28.8 mg g⁻¹. The process was endothermic with ΔH in the range 29.2–50.7 kJ mol⁻¹ accompanied by increase in entropy and decrease in Gibbs energy. The results have shown that kaolinite, montmorillonite and their poly(oxo zirconium) and tetrabutyl-ammonium derivatives could be used as adsorbents for separation of Cu(II) from aqueous solution.     

Variation of the aerosol charge neutralization coefficient in the entire particle size range

The rate at which the mean charge on aerosol particles relaxes to its steady-state value under bipolar charging is characterized by the neutralization rate constant, β (s⁻¹). It is an important parameter for fixing the nt product in charge neutralizers as well as in the theory of charging-induced diffusion. Here we compute the neutralization coefficient, β/n (where n is the mean ion density), as a function of particle size through the use of ion-particle combination coefficients provided by the recent theories. The results indicate that β/n decreases from a continuum limit value of 3.1 × 10⁻⁶ cm³ s⁻¹, to a free molecular limit value of 1.4 × 10⁻⁶ cm³ s⁻¹. The changeover occurs rapidly in the transitional regime (10–100 nm). This clearly indicates that the nt product required to attain steady state is higher for nano particles than for larger ones. The paper also presents the variations of the mean square variance of charge, the coefficients of charging-induced drift and diffusion, as a function of particle size.