Development of Cu-based oxygen carriers for chemical-looping combustion

In a chemical-looping combustion (CLC) process, gas (natural gas, syngas, etc.) is burnt in two reactors. In the first one, a metallic oxide that is used as oxygen source is reduced by the feeding gas to a lower oxidation state, being CO₂ and steam the reaction products. In the second reactor, the reduced solid is regenerated with air to the fresh oxide, and the process can be repeated for many successive cycles. CO₂ can be easily recovered from the outlet gas coming from the first reactor by simple steam condensation. Consequently, CLC is a clean process for the combustion of carbon containing fuels preventing the CO₂ emissions to the atmosphere. The main drawback of the overall process is that the carriers are subjected to strong chemical and thermal stresses in every cycle and the performance and mechanical strength can decay down to unacceptable levels after enough number of cycles in use.In this paper the behaviour of CuO as an oxygen carrier for a CLC process has been analysed in a thermogravimetric analyser. The effects of carrier composition and preparation method used have been investigated to develop Cu-based carriers exhibiting high reduction and oxidation rates without substantial changes in the chemical, structural and mechanical properties for a high number of oxidation-reduction cycles. It has been observed that the carriers prepared by mechanical mixing or by coprecipitation showed an excellent chemical stability in multicycle tests in thermobalance, however, the mechanical properties of these carriers were highly degraded to unacceptable levels. On the other hand, the carriers prepared by impregnation exhibited excellent chemical stability without substantial decay of the mechanical strength in multicycle testing. These results suggest that copper based carriers prepared by impregnation are good candidates for CLC process.     

Reactivity of a NiO/Al2O3 oxygen carrier prepared by impregnation for chemical-looping combustion

The reactivity of a Ni-based oxygen carrier prepared by hot incipient wetness impregnation (HIWI) on α-Al₂O₃ with a NiO content of 18 wt% was studied in this work. Pulse experiments with the reduction period divided into 4-s pulses were performed in a fluidized bed reactor at 1223 K using CH₄ as fuel. The number of pulses was between 2 and 12. Information about the gaseous product distribution and secondary reactions during the reduction was obtained. In addition to the direct reaction of the combustible gas with the oxygen carrier, CH₄ steam reforming also had a significant role in the process, forming H₂ and CO. This reaction was catalyzed by metallic Ni in the oxygen carrier and H₂ and CO acted as intermediate products of the combustion. No evidence of carbon deposition was found in any case. Redox cycles were also carried out in a thermogravimetric analyzer (TGA) with H₂ as fuel. Both tests showed that there was a relation between the solid conversion reached during the reduction and the relative amount of NiO and NiAl₂O₄ in the oxygen carrier. When solid conversion increased, the NiO content also increased, and consequently NiAl₂O₄ decreased. Approximately 20% of the reduced nickel was oxidized to NiAl₂O₄, regardless ΔX_s. NiAl₂O₄ was also an active compound for the combustion reaction, but with lower reactivity than NiO. Further, the consequences of these results with respect to the design of a CLC system were investigated. When formation of NiAl₂O₄ occurred, the average reactivity in the fuel reactor decreased. Therefore, the presence of both NiO and NiAl₂O₄ phases must be considered for the design of a CLC facility.     

CO2 capture using oxygen enhanced combustion strategies for natural gas power plants

This paper describes a series of experiments conducted with natural gas in air and in mixtures of oxygen and recycled flue gas, termed O₂/CO₂ recycle combustion. The objective is to enrich the flue gas with CO₂ to facilitate its capture and sequestration. Detailed measurements of gas composition, flame temperature and heat flux profiles were taken inside CANMET's 0.3 MWth down-fired vertical combustor fitted with a proprietary pilot scale burner. Flue gas composition was continuously monitored. The effects of burner operation, including swirling of secondary stream and air staging, on flame characteristics and NO_x emissions were also studied. The results of this work indicate that oxy-gas combustion techniques based on O₂/CO₂ combustion with flue gas recycle offer excellent potential for retrofit to conventional boilers for CO₂ emission abatement. Other benefits of the technology include considerable reduction and even elimination of NO_x emissions, improved plant efficiency due to lower gas volume and better operational flexibility.     

Chemical-looping combustion in a 300 W continuously operating reactor system using a manganese-based oxygen carrier

Chemical-looping combustion (CLC) is a method for the combustion of fuel gas with inherent separation of carbon dioxide. This technique involves the use of two interconnected reactors. A solid oxygen carrier reacts with the oxygen in air in the air reactor and is then transferred to the fuel reactor, where the fuel gas is oxidized to carbon dioxide and water by the oxygen carrier. Fuel gas and air are never mixed and pure CO₂ can easily be obtained from the flue gas exit. The oxygen carrier is recycled between both reactors in a regenerative process. This paper presents the results from a continuously operating laboratory CLC unit, consisting of two interconnected fluidized beds. The feasibility of the use of a manganese-based oxygen carrier supported on magnesium stabilized zirconia was tested in this work. Natural gas or syngas was used as fuel in the fuel reactor. Fuel flow and air flow was varied, the thermal power was between 100 and 300 W, and the air ratio was between 1.1 and 5.0. Tests were performed at four temperatures: 1073, 1123, 1173 and 1223 K. The prototype was successfully operated at all conditions with no signs of agglomeration or deactivation of the oxygen carrier. The same particles were used during 70 h of combustion and the mass loss was 0.038% per hour, although the main quantity was lost in the first hour of operation. In the combustion tests with natural gas, methane was detected in the exit flue gases, while CO and H₂ were maintained at low concentrations. Higher temperature or lower fuel flows increases the combustion efficiency, which ranged from 0.88 to 0.99. On the other hand, the combustion of syngas was complete for all experimental conditions, with no CO or H₂ present in the gas from the fuel reactor.     

Solid fuels in chemical-looping combustion using a NiO-based oxygen carrier

The feasibility of using three different solid fuels in chemical-looping combustion (CLC) has been investigated using NiO as oxygen carrier. A laboratory fluidized-bed reactor system for solid fuel was used, simulating a chemical-looping combustion system by exposing the sample to alternating reducing and oxidizing conditions. In each reducing phase 0.2 g of fuel was added to the reactor containing 20 g oxygen carrier. The experiments were performed at 970 °C. Compared to previously published results with other oxygen carriers the reactivity of the used Ni-particles was considerably lower for the high-sulphur fuel and higher for the low-sulphur fuel. Much more unconverted CO was released and the fuel conversion was much slower for high-sulphur fuel such as petroleum coke, suggesting that the nickel-based oxygen carrier was deactivated by the presence of sulphur. The NiO particles also showed good reactivity with methane and a syngas mixture of 50% H₂ and 50% CO. For all experiments the oxygen carrier showed good fluidizing properties without any signs of agglomeration.     

Syngas combustion in a chemical-looping combustion system using an impregnated Ni-based oxygen carrier

Chemical-looping combustion (CLC) has emerged as a promising option for CO₂ capture because this gas is inherently separated from the other flue gas components and thus no energy is expended for the separation. This technology would have some advantages if it could be adapted for its use with coal as fuel. In this sense, a process integrated by coal gasification and CLC could be used in power plants with low energy penalty for CO₂ capture. This work presents the results obtained in the combustion of syngas as fuel with a Ni-based oxygen carrier prepared by impregnation in a CLC plant under continuous operation. The effect on the oxygen carrier behaviour and the combustion efficiency of several operating conditions was determined in the continuous CLC plant. High combustion efficiencies (～99%), close to the values limited by thermodynamics, were reached at oxygen carrier-to-fuel ratios higher than 5. The temperature in the FR had a significant influence, although high efficiencies were obtained even at 1073 K. The syngas composition had small effect on the combustion, obtaining high and similar efficiencies with syngas fuels of different composition, even in the presence of high CO concentrations. The low reactivity of the oxygen carrier with CO seemed to indicate that the water gas shift reaction acts as an intermediate step in the global reaction of the syngas in a continuous CLC plant. Neither agglomeration nor carbon deposition problems were detected during 50 h of continuous operation in the prototype. The obtained results showed that the impregnated Ni-based oxygen carrier could be used in a CLC plant for the combustion of syngas produced in an integrated gasification combined cycle (IGCC).     

NiO/Al2O3 oxygen carriers for chemical-looping combustion prepared by impregnation and deposition-precipitation methods

Ni-based oxygen carriers (OC) with different NiO content were prepared by incipient wet impregnation, at ambient (AI), and hot conditions (HI) and by deposition-precipitation (DP) methods using γ-Al₂O₃ and α-Al₂O₃ as supports. The OC were characterized by BET, Hg porosimetry, mechanical strength, TPR, XRD and SEM/EDX techniques. Reactivity of the OC was measured in a thermogravimetric analyzer and methane combustion selectivity towards CO₂ and H₂O, attrition rate, and agglomeration behavior were analyzed in a batch fluidized bed reactor during multicycle reduction-oxidation tests.XRD and TPR analysis showed the presence of both free NiO and NiAl₂O₄ phases in most of the OC. The interaction of the NiO with the alumina during OC preparation formed NiAl₂O₄ that affected negatively to the OC reactivity and methane combustion selectivity towards CO₂ and H₂O during the reduction reaction. The NiO-alumina interaction was more affected by the support type than by the preparation method used. The NiO-alumina interaction was stronger in the OC prepared on γ-Al₂O₃.The OC were evaluated in the fluidized bed reactor with respect to the agglomeration process. OC prepared by the AI and HI methods with NiO contents up to 25 wt%, OC prepared by the DP method on γ-Al₂O₃ with NiO content lower than 30 wt%, and OC prepared by the DP method on α-Al₂O₃ with a NiO content lower than 26 wt% did not agglomerated. OC that agglomerated showed an external layer of NiO over the particles. It seems that the most important factor affecting to the formation of the external NiO layer on the OC, and so to the agglomeration process, was the metal content of the OC. The attrition rates of the OC prepared using γ-Al₂O₃ as support were higher than the ones prepared using α-Al₂O₃ as support, and in general the attrition rates of all the OC were low.The OC prepared by AI, HI or DP methods on α-Al₂O₃ as support had appropriated characteristics to be used in the chemical-looping combustion process.     

Effect of temperature on reduction reactivity of oxygen carrier particles in a fixed bed chemical-looping combustor

In a chemical-looping combustor (CLC), gaseous fuel is oxidized by metal oxide particle, e.g. oxygen carrier, in a reduction reactor (combustor), and the greenhouse gas CO₂ is separated from the exhaust gases during the combustion. In this study, NiO/bentonite particle was examined on the basis of reduction reactivity, carbon deposition during reduction, and NO_x formation during oxidation. Reactivity data for NiO/bentonite particle with methane and air were presented and discussed. During the reduction period, most of the CH₄ are converted to CO₂ with small formation of CO. Reduction reactivity (duration of reduction) of the NiO/bentonite particle increased with temperature, but at higher temperature, it is somewhat decreased. The NiO/bentonite particle tested showed no agglomeration or breakage up to 900 ‡C, but at 1,000 ‡C, sintering took place and lumps of particles were formed. Solid carbon was deposited on the oxygen carrier during high conversion region of reduction, i.e., during the end of reduction. It was found that the appropriate temperature for the NiO/bentonite particle is 900 ‡C for carbon deposition, reaction rate, and duration of reduction. We observed experimentally that NO, NO₂, and N₂O gases are not generated during oxidation.     

Reduction and oxidation kinetics of Mn3O4/Mg-ZrO2 oxygen carrier particles for chemical-looping combustion

The kinetics of reduction with methane and oxidation with oxygen of Mn₃O₄ supported on Mg-ZrO₂ prepared by freeze granulation has been investigated. The reactivity experiments were performed in a thermogravimetric analyzer (TGA) using different reacting gas concentrations and temperatures in the range of 1073-1223 K. The oxygen carrier particles showed high reactivity during both reduction and oxidation at all investigated temperatures. An empirical reaction model, which assumes a linear relation between time and conversion, was used to determine the kinetic parameters for reduction and oxidation, with chemical reaction being the main resistance to the reaction. The order of reaction found was 1 with respect to CH₄ and 0.65 with respect to O₂. The activation energy for the reduction reaction was 119 and for the oxidation reaction. The reactivity data and kinetic parameters were used to estimate the solid inventory in the air and fuel reactor of a CLC system. The optimum solid inventory obtained was at a value of ΔX_s=0.4. At these conditions, the recirculation rate of oxygen carrier between air and fuel reactor was per MW of fuel, which could be accomplished in an industrial reactor. The high reactivity of the Mn₃O₄/Mg-ZrO₂ with both methane and oxygen showed that this is a very promising oxygen carrier for CLC.     

Effect of support on reactivity and selectivity of Ni-based oxygen carriers for chemical-looping combustion

Different Ni-based oxygen carriers were prepared by dry impregnation using γ-Al₂O₃ as support. The reactivity, selectivity during methane combustion, attrition rate and agglomeration behavior of the oxygen carriers were measured and analyzed in a thermogravimetric analyzer and in a batch fluidized bed during multi-cycle reduction-oxidation tests.Ni-based oxygen carriers prepared on γ-Al₂O₃ showed low reactivity and low methane combustion selectivity to CO₂ and H₂O, because most of the impregnated NiO reacted to NiAl₂O₄. To avoid or to minimize the interaction of NiO with alumina some modifications of the support via thermal treatment or chemical deactivation with Mg or Ca oxides were analyzed. Thermal treatment of γ-Al₂O₃ at 1150 °C produced the phase transformation to α-Al₂O₃. Ni-based oxygen carriers prepared on α-Al₂O₃, MgAl₂O₄, or CaAl₂O₄ as support showed very high reactivity and high methane combustion selectivity to CO₂ and H₂O because the interaction between the NiO and the support was decreased. In addition, these oxygen carriers had very low attrition rates and did not show any agglomeration problems during operation in fluidized beds, and so, they seem to be suitable for the chemical-looping combustion process.     

Behavior of ilmenite as oxygen carrier in chemical-looping combustion

For a future scenery where will exist limitation for CO₂ emissions, chemical-looping combustion (CLC) has been identified as a promising technology to reduce the cost related to CO₂ capture from power plants. In CLC a solid oxygen-carrier transfers oxygen from the air to the fuel in a cyclic manner, avoiding direct contact between them. CO₂ is inherently obtained in a separate stream. For this process the oxygen-carrier circulates between two interconnected fluidized-bed reactors. To adapt CLC for solid fuels the oxygen-carrier reacts with the gas proceeding from the solid fuel gasification, which is carried out right in the fuel-reactor. Ilmenite, a natural mineral composed of FeTiO₃, is a low cost and promising material for its use on a large scale in CLC.The aim of this study is to analyze the behavior of ilmenite as oxygen-carrier in CLC. Particular attention was put on the variation of chemical and physical characteristics of ilmenite particles during consecutive redox cycles in a batch fluidized-bed reactor using CH₄, H₂ and CO as reducing gases. Reaction with H₂ was faster than with CO, and near full H₂ conversion was obtained in the fluidized-bed. Lower reactivity was found for CH₄. Ilmenite increased its reactivity with the number of cycles, especially for CH₄. The structural changes of ilmenite, as well as the variations in its behavior with a high number of cycles were also evaluated with a 100 cycle test using a CO + H₂ syngas mixture. Tests with different H₂:CO ratios were also made in order to see the reciprocal influence of both reducing gases and it turned out that the reaction rate is the sum of the individual reaction rates of H₂ and CO. The oxidation reaction of ilmenite was also investigated. An activation process for the oxidation reaction was observed and two steps for the reaction development were differenced. The oxidation reaction was fast and complete oxidation could be reached after every cycle. Low attrition values were found and no defluidization was observed during fluidized-bed operation. During activation process, the porosity of particles increased from low porosity values up to values of 27.5%. The appearance of an external shell in the particle was observed, which is Fe enriched. The segregation of Fe from TiO₂ causes that the oxygen transport capacity, R_OC, decreases from the initial R_OC = 4.0% to 2.1% after 100 redox cycles.     

In situ gasification of a lignite coal and CO2 separation using chemical looping with a Cu-based oxygen carrier

Chemical looping combustion (CLC) has the inherent property of separating CO₂ from flue gases. This paper is concerned with the application of chemical looping to the combustion of a solid fossil fuel (a lignite and its char) in a technique whereby the fuel is gasified in situ using CO₂ in the presence of a batch of supported copper oxide (the “oxygen carrier”) in a single reactor. As the metal oxide becomes depleted, the feed of fuel is discontinued, the inventory of fuel is reduced by further gasification and then the contents are re-oxidised by the admission of air to the reactor, to begin the cycle again. The choice of oxides is restricted because it requires an oxide which is exothermic during reduction to balance the endothermic gasification reactions. Copper has such oxides, but a key question is whether or not it can withstand temperatures at which gasification rates are significant (∼1173 K), particularly from the point of view of avoiding sintering and deactivation of the carrier in its reduced form. It was found that an impregnated carrier, made by impregnating a θ-alumina catalyst support (BET area 157 m²/g) with a saturated solution of copper and aluminium nitrates, acted as a durable carrier over 20 cycles of reduction and oxidation, using both Hambach lignite coal, and its char, and with air as the oxidising agent. During the course of the experiments, the BET surface area of the support fell from ∼60 m²/g, just after preparation, to around 6 m²/g after 20 cycles. However, this fall did not appear to affect the overall capacity of the oxygen carrier to react with fuels and its effect on the kinetics of the reaction with CO did not influence the outcome of the experiments, since the overall performance of the looping scheme is dominated by the much slower kinetics of the gasification reaction. The apparent kinetics of the gasification are faster in the presence of the looping agent: this is because the bulk concentration of CO in the presence of the looping agent is lower, and partly because the destruction of CO in the vicinity of a gasifying particle enhances the rate of removal of CO by mass transfer (and increases the local concentration of CO₂). There was little evidence to suggest a direct reaction between carbonaceous and carrier solids, other than via a gaseous intermediate. However, the observation of finite rates of conversion in a bed of active carrier, fluidised by nitrogen, is a scientific curiosity, which we have not been able to explain satisfactorily. At 1173 K, as used here, rates of gasification of Hambach lignite, and its char, are significant. The CuO in the carrier decomposes at 1173 K to produce gas-phase O₂ and Cu₂O: both can react with CO produced by gasification, whilst the O₂ can react directly with the char.     

In situ gasification and CO2 separation using chemical looping with a Cu-based oxygen carrier: Performance with bituminous coals

This paper is concerned with the chemical looping combustion of coal in a technique whereby the fuel is gasified in situ using CO₂ in the presence of a batch of supported copper oxide (the “oxygen carrier”) in a single reactor. As the metal oxide becomes depleted, the feed of fuel is discontinued, the inventory of fuel is reduced by further gasification and then the contents are re-oxidised by the admission of air to the reactor, to begin the cycle again. A catalyst support, impregnated with a saturated solution of copper and aluminium nitrates, acted as a durable oxygen carrier over numerous cycles of reduction and oxidation, using air as the oxidant. Two bituminous coals (Taldinskaya, Russia, and Illinois No. 5, USA) were investigated and compared with a lignite (Hambach, Germany). The lignite was highly reactive and was gasified completely by 15 mol% CO₂ in N₂ at 1203 K and 1 bar, so that there was no build up of char in the bed. The bituminous coals produced chars much less reactive than the lignite char, so that there was a steady accumulation of char in the bed with number of cycles, with the degree of accumulation being dependent on the reactivity of the char. Since the kinetics of gasification by CO₂ of the chars from either bituminous coal were slow, their rates were controlled by intrinsic chemical kinetics and were not affected by the ability of the oxygen carrier to alter the rates of external mass transfer when gasification is rapid. However, it is likely that rates of gasification in the presence of the carrier are still larger than in its absence, owing to the overall lower [CO] present in the bulk of the fluidised bed during chemical looping. At the temperature used, the carrier was cycling between Cu and Cu₂O, since CuO is only stable if the partial pressure of O₂ exceeds 0.03 bar at 1203 K. The CuO decomposes to Cu₂O and O₂ relatively rapidly at these temperatures, once the oxygen concentration is effectively zero. It was impossible to ascertain in our experiments whether the oxygen so generated, after the switching of the air for nitrogen before the start of the succeeding cycle of gasification, made any substantial difference to the reactivity of the char present in the bed. The rate of oxidation of the carrier was found to be much more rapid than the rate of oxidation of the inventory of char. This allows a preferential oxidation of the carrier and most likely accounts for why progressively less CO and CO₂ is produced during successive cycles with short periods of oxidation: the increasingly reduced carrier reacts more rapidly than the char. There was no obvious impact from the sulphur contained in the fuels, but longer-term testing is needed. No agglomeration between the carrier particles and the ash was observed, despite the high temperatures during oxidation.     

Reduction and oxidation kinetics of Co-Ni/Al2O3 oxygen carrier involved in a chemical-looping combustion cycles

The solid-state kinetics of Co-Ni/Al₂O₃ oxygen carrier is studied using non-isothermal reaction data and a non-linear regression analysis. XRD analysis of the fresh samples shows that NiO is the dominant reducible phase of the oxygen carrier. Pulse chemisorption suggests a negligible nuclei growth over the repeated reduction/oxidation cycles. Mercury porosimetry confirms that the pore size of the carrier particle is slightly increased following reduction. A nucleation and nuclei growth model and an unreacted shrinking-core model are developed based on the oxygen carrier texture change during reduction/oxidation, as observed by pulse chemisorption and mercury porosimetry. Model parameters are calculated using H₂-TPR and O₂-TPO data. It is found that the random nucleation model describes solid phase changes adequately. The determined apparent activation energies are 45 and 44 kJ/mol for the reduction and oxidation, respectively. The established kinetic model is successfully evaluated for the reduction cycle using a CREC mini-fluidized Riser Simulator reactor operating under expected conditions of large industrial scale fluidized CLC units.     

Syngas combustion characteristics of four oxygen carrier particles for chemical-looping combustion in a batch fluidized bed reactor

Syngas combustion characteristics of oxygen carrier particles have been investigated. Experiments were performed on four oxygen carrier particles in a fluidized bed reactor. All four oxygen carrier particles showed high gas conversion, high CO₂ selectivity, and low CO concentration in the reducer and very low NOx (NO, NO₂, N₂O) emissions in the oxidizer. Moreover, all particles showed good regeneration ability during successive reduction-oxidation cyclic tests up to the 10 ^th cycle. The results indicate that inherent CO₂ separation, NOx-free combustion, and long-term operation without reactivity decay of oxygen carrier particles are possible in a syngas fueled chemical-looping combustion system with NiO/bentonite, NiO/NiAl₂O₄, Co _x O _y /CoAl₂O₄, and OCN-650 particles. However, Co _x O _y /CoAl₂O₄ represented slight decay of oxidation reactivity with the number of cycles increased and the oxidation rate slower than other particles.     

Solid fuels in chemical-looping combustion using oxide scale and unprocessed iron ore as oxygen carriers

Chemical-looping combustion (CLC) is a novel technology that can be used to meet demands on energy production without CO₂ emissions. The CLC-process includes two reactors, an air and a fuel reactor. Between these two reactors oxygen is transported by an oxygen carrier, which most often is a metal oxide. This arrangement prevents mixing of N₂ from the air with CO₂ from the combustion. The combustion gases consist almost entirely of CO₂ and H₂O. Therefore, the technique reduces the energy penalty that normally arises from the separation of CO₂ from other flue gases, hence, CLC may make capture of CO₂ cheaper.Iron ore and oxide scale from steel production were tested as oxygen carriers in CLC batch experiments with solid fuels. Petroleum coke, charcoal, lignite and two bituminous coals were used as fuels.The experiments were carried out in a laboratory fluidized-bed reactor that was operating cyclically with alternating oxidation and reduction phases. The exhaust gases were led to an analyzer where the contents of CO₂, CO, CH₄ and O₂ were measured. Gas samples collected in bags were used to analyze the content of hydrogen in a gas chromatograph.The results showed that both the iron ore and the oxide scale worked well as oxygen carrier and both oxygen carriers increased their reactivity with time.     

Investigation into a gas–solid–solid three-phase fluidized-bed carbonator to capture CO2 from combustion flue gas

A two-dimensional (2D) transient model was developed to simulate the local hydrodynamics of a gas (flue gas)–solid (CaO)–solid (CaCO₃) three-phase fluidized-bed carbonator using the computational fluid dynamic method, where the chemical reaction model was adopted to determine the molar fraction of CO₂ at the exit of carbonator and the partial pressure of CO₂ in the carbonator. This investigation was intended to improve an understanding of the chemical reaction effects of CaO with CO₂ on the CO₂ capture efficiency of combustion flue gases. For this purpose, we had utilized Fluent 6.2 to predict the CO₂ capture efficiency for different operation conditions. The adopted model concerning the reaction rate of CaO with CO₂ is joined into the CFD software. Model simulation results, such as the local time-averaged CO₂ molar fraction and conversion of CaO, were validated by experimental measurements under varied operating conditions, e.g., the fraction of active CaO, chemical reaction temperature, particle size, and cycle number at different locations in a gas–solid–solid three-phase fluidized bed carbonator. Furthermore, the local transient hydrodynamic characteristics, such as gas molar fraction and partial pressure were predicted reasonably by the chemical reaction model adopted for the dynamic behaviors of the gas–solid–solid three-phase fluidized bed carbonator. On the basis of this analysis, capture CO₂ strategies to reduce CO₂ molar fraction in exit of carbonator reactor can be developed in the future. It is concluded that a fluidized bed of CaO can be a suitable reactor to achieve very effective CO₂ capture from combustion flue gases.     

Reduction and oxidation properties of Fe2O3/ZrO2 oxygen carrier for hydrogen production

Fe₂O₃ is a promising oxygen carrier for hydrogen production in the chemical-looping process. A set of kinetic studies on reduction with CH₄, CO and H₂ respectively, oxidation with water and oxygen containing Ar for chemical-looping hydrogen production was conducted. Fe₂O₃ (20 wt.%)/ZrO₂ was prepared by a co-precipitation method. The main variables in the TGA (thermogravimetric analyzer) experiment were temperatures and gas concentrations. The reaction kinetics parameters were estimated based on the experimental data. In the reduction by CH₄, CO and H₂, the reaction rate changed near FeO. Changes in the reaction rate due to phase transformation were observed at low temperature and low gas concentration during the reduction by CH₄, but the phenomenon was not remarkable for the reduction by CO and H₂. The reduction rate achieved using CO and H₂ was relatively faster than achieved using CH₄. The Hancock and Sharp method of comparing the kinetics of isothermal solid-state reactions was applied. A phase boundary controlled model (contacting sphere) was applied to the reduction of Fe₂O₃ to FeO by CH₄, and a different phase boundary controlled model (contacting infinite slab) was fit well to the reduction of FeO to Fe by CH₄. The reduction of Fe₂O₃ to Fe by CO and H₂ can be described by the former phase boundary controlled model (contacting sphere). This phase boundary controlled model (contacting sphere) also fit well for the oxidation of Fe to Fe₃O₄ by water and FeO to Fe₂O₃ by oxygen containing Ar. These kinetics data could be used to design chemical-looping hydrogen production systems.     

Mechanistic investigation of chemical looping combustion of coal with Fe2O3 oxygen carrier

The reaction of three Chinese coals with Fe₂O₃ oxygen carrier (OC) was performed in a thermogravimetric analyzer (TGA), with special focuses on the effects of varying heating rate and coal rank on reactivity. Fourier transform infrared spectroscopy (FTIR) was used to in situ detect the emitted gases from TGA. Field scanning electron microscopy/energy-dispersive X-ray spectrometry (FSEM-EDX) was used to study the morphology and elemental compositions of the reaction residues collected from TGA and the related phase evaluation was further identified by X-ray diffraction (XRD). Through all these experiments, it was found that the pyrolysis of coal samples without Fe₂O₃ OC under N₂ atmosphere underwent the dehydration and the ensuing primary and secondary pyrolysis stages. The increasing heating rate shifted the characteristic temperature (T_m) of the primary pyrolysis to a higher temperature and favored a more rapid generation of volatile matters. When the three coals reacting with Fe₂O₃ OC, TGA results demonstrated even over 200 °C, the reaction still experienced the partial pyrolysis at the relatively low temperature and the ensuing two reactions of Fe₂O₃ with the pyrolysis products at the primary and secondary stages. The coal of low rank with high volatile content should be preferred for the full conversion of coal into CO₂. Furthermore, the activation energy of Fe₂O₃ OC reacting with PDS at its primary pyrolysis stage was the largest, more than 70 kJ/mol. Finally, SEM-EDX and further XRD analysis of the residues from the reaction of PDS with Fe₂O₃ OC indicated the reduced counterpart of Fe₂O₃ was Fe₃O₄, and some inert iron compounds such as Fe₂SiO₄ and FeAl₂O₄ were also generated, which might deteriorate the reactivity of Fe₂O₃ OC.     

Combustion characteristics of coal in a mixture of oxygen and recycled flue gas

The combustion of coal in a mixture of pure O₂ and recycled flue gas is one variant of a novel combustion approach called oxy-fuel combustion. With the absence of N₂, this approach leads to a flue gas stream highly enriched in CO₂. For many applications, this flue gas stream can then be compressed and sequestered without further separation. As a result, oxy-fuel combustion is an attractive way to capture CO₂ produced from fossil fuel combustion. When coal is burned in this O₂ and CO₂ rich environment, its combustion characteristics can be very different from conventional air-fired combustion. In CETC-O, a vertical combustor research facility has been used in the past years to investigate the combustion characteristics of several different coals with this variant of oxy-fuel combustion. This included flame stability, emissions of NO_x, SO_x and trace elements, heat transfer, in-furnace flame profiles and flue gas compositions. This paper will report some of the major findings obtained from these research activities.