高性能硫/碳凝胶复合正极材料的制备及应用

以碳凝胶作导电骨架,合成硫/碳凝胶复合物.XRD、SEM等表征显示,该复合材料完全保持了碳凝胶的形貌,颗粒大小在10μm以下,硫吸附在碳凝胶内部空隙中呈无定形态,表现出良好的电化学性能.以0.1C放电,该材料首圈放电容量达到1311mAh/g.0.2C循环充放,首圈放电容量为1107.1mAh/g,30周充放电后,放电容量仍不低于800mAh/g.     

纳米磷酸铁锂的制备及电化学性能研究

利用液相沉淀法合成了纳米级磷酸铁,并以此为铁源,通过碳热还原技术制备了粒径均匀的纳米级球形LiFePO4/C正极材料。经热分析(TG-DSC)、X射线衍射(XRD)、扫描电镜(SEM)、透射电镜(TEM)以及恒电流充放电测试,研究了纳米磷酸铁及纳米磷酸铁锂材料的结构、形貌以及电化学性能。实验结果表明材料的首次放电比容量达161.8 mAh.g-1(0.1C),库仑效率为98.3%;室温下在0.2C、0.5C、1C、2C及5C倍率充放电其首次放电比容量分别为156.5、144、138.9、125.6和105.7 mAh·g-1,材料具有较好的倍率性能。     

温度对碳球形貌及超级电容性能的影响

以三氯乙烷和二氯乙烷为原料, 金属钠为还原剂, 在溶剂热条件(100~150 ℃)下使氯代乙烷中的碳氯键和碳氢键发生断裂制备了碳纳米球, 并对制备的碳纳米球进行了表征. X射线衍射结果表明, 样品为类石墨结构, 衍射信号宽且弱, 表明样品的结晶性较差; 拉曼光谱分析结果也表明样品具有较高的无序度. 样品的SEM与TEM分析结果表明, 在较高的反应温度下, 碳球具有更好的单分散性, 碳球的粒径随温度的升高而增大; 选区电子衍射结果表明碳球内部为无定形的类石墨结构. 以碳纳米球为负极材料的锂离子电池测试结果表明, 50周循环后比容量为941 mA·h/g, 库仑效率接近100%, 放电容量保持率为103.7%, 具有良好的循环稳定性. 测试了不同温度下制备样品的超级电容器性能, 发现120 ℃下制备的碳纳米球具有较高的比电容和较低的内阻值, 比电容高达130 F/g, 经过1000周循环充放电后比电容衰减比例低于14%, 具有较高的稳定性.     

高比能LiFePO_4的制备及性能研究

应用液相沉淀法-固相烧结法制备高密度的LiFePO4/C及纯相LiFePO4.X射线衍射、扫描电镜、傅立叶红外光谱仪、电化学性能测试表明:该样品具有单一的橄榄石结构和3.4 V左右的放电平台,掺碳的LiFe-PO4具有更优良的性能,粒度较小粒径分布均匀,振实密度达1.46 g/cm3,0.1C首次放电比容量为144.6mAh/g,循环20次后容量保持率为93.2%,1C倍率首次放电比容量为133.5 mAh/g,循环20次后容量下降8.76%.     

碳包覆硅/石墨复合材料的制备及其电化学性能

本文以工业硅粉(600目)为原料,通过高能球磨和热解包碳方法制备了碳包覆纳米硅,在此基础上采用简单的机械球磨方法制备了碳包覆/石墨复合材料,并系统研究了碳包覆量及硅/石墨比例对碳包覆硅/石墨复合材料电化学性能的影响.与商业纳米硅粉/石墨复合材料相比,工业硅粉/石墨复合材料的循环性能及倍率性能均得到改善.通过高能球磨和热处理法得到的碳包覆材料为无定形碳和晶态硅材料的复合,所获碳包覆硅材料一次颗粒的粒径在100～200 nm左右.碳包覆量对材料的电化学性能有着重要影响,Si/C-2-1复合材料表现出高的可逆比容量、良好的倍率性能和循环稳定性,在0.1C倍率下,可逆比容量高达492.6 mA h·g~(-1),循环100周后容量保持率达85.8%,1C电流密度下放电比容量达369.7 mAh·g~(-1),为0.1C的73.9%.提高碳包覆硅/石墨复合材料中硅含量的比例可以提升其比容量,当硅含量达到20%时,Si/C-2-3复合材料在0.1C倍率下可逆比容量达到600.4 mAh·g~(-1),但材料循环性能有所下降,说明石墨在稳定硅/碳复合材料循环性能方面发挥着非常重要的作用.     

LiFePO4的制备、结构与电性能研究

应用高速球磨-高温固相反应法于不同煅烧温度(400~700℃)下合成L iFePO4锂离子电池正极材料,X-射线衍射、扫描电镜和恒电流充放电等测试表明,煅烧温度对合成的L iFePO4晶体结构、表观形貌以及电化学性能均有很大影响;经600℃煅烧得到的L iFePO4样品具有良好的充放电性能,以0.1C倍率充放电,首次放电比容量为128.8 mAh/g,第15次放电比容量为129.1 mAh/g,充放电效率在99.7%以上;其高温充放电性能亦佳.     

纳米级LiFePO_4材料的水热模板法合成及其性能研究

采用水热模板法合成纳米级LiFePO4材料,改变水热反应中表面活性剂(十六烷基三甲基溴化铵)的比例控制样品颗粒生成的大小.SEM测试表明,合成的LiFePO4晶粒尺寸与表面活性剂的配比密切相关,范围在几十到几百nm之间.充放电试验表明,合成的纳米级LiFePO4材料电极具有优良的电化学性能,其0.1C放电最高比容量可达150 mAh/g,而1C和2C放电比容量也分别有140 mAh/g和126 mAh/g.     

不同碳源对多孔球形LiFePO4/C复合材料的影响

采用喷雾干燥-碳热还原法(SDCTM),分别研究了无机和有机碳源对锂离子正极材料LiFePO4/C形貌、结构及其充放电性能的影响。结果表明:以无机碳源炭黑制备的LiFePO4/C呈不规则球形,一次颗粒粒径在800nm左右,比表面积为2m2·g-1,0.1C放电比容量为107.3mAh·g-1。而以有机碳源制备的LiFePO4/C,其形貌较为规则,呈多孔球形结构,具有较高的比表面积和放电比容量。其中,以柠檬酸为碳源制备的多孔球形LiFePO4/C复合材料,其孔径均在50nm左右,比表面积可达32m2·g-1;在室温下,0.1C和10C首次放电比容量分别为158.8和87.2mAh·g-1,具有优异的循环性能和高倍率充放电性能。     

纳米碳管的电化学贮锂性能

用透射电镜、高分辩透射电镜、X射线衍射和拉曼光谱表征了用催化热解法制备的纳米碳管的结构,研究了纳米碳管的电化学嵌脱锂性能.以纳米级铁粉为催化剂热解乙炔气得到的纳米碳管石墨化程度较低,结构中存在褶皱的石墨层、乱层石墨和微孔等缺陷,具有较高的贮锂容量,初始容量为640mAh/g,但循环稳定性较差.而以纳米级氧化铁粉为催化剂热解乙烯得到的纳米碳管结构比较规则,循环稳定性较好,但贮锂容量较低,初始容量为282 mAh/g.讨论了纳米碳管的结构对其温度特性和不同电流密度下的充放电容量的影响.     

由含铝金属有机骨架材料制备的多孔碳在锂硫电池中的应用

采用水热法制备了一种含铝金属有机骨架材料, 其在高温下发生炭化得到多孔碳, 最后与硫复合制得锂硫电池正极材料. XRD图谱显示在高温炭化时多孔碳样品出现了部分石墨化. N₂等温吸附-脱附测试分析显示合成的多孔碳材料含有微孔和介孔结构. 对不同载硫量的锂硫电池进行了充放电性能测试, 结果显示S质量分数为46.3%的样品在0.01 C倍率下首次放电容量达到1272 mA·h/g; 在0.1 C倍率下首次放电容量为934 mA·h/g, 循环性能良好.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Microwave-assisted copper-catalyzed stereoselective ring expansion of three-membered heterocycles with α-diazo-β-dicarbonyl compounds

Microwave-assisted copper-catalyzed ring expansions of three-membered heterocycles with α-diazo-β-dicarbonyl compounds were investigated. Thiiranes generated 3-acyl-5,6-dihydro-1,4-oxathiines in the presence of copper sulfate and trans-3-acyl-5,6-dihydro-1,4-oxathiines as stereospecific products for 1,2-disubstituted cis-thiiranes through an intramolecular S_N2 process. Oxiranes gave rise to 2-acyl-5,6-dihydro-1,4-dioxines under the catalysis of copper hexafluoroacetylacetonate and cis-3-acyl-5,6-dihydro-1,4-dioxines as stereospecific products for 1,2-disubstituted cis-oxiranes via an intimate ion-pair mechanism. The current method provides a direct and simple strategy in efficient preparation of 3-acyl-5,6-dihydro-1,4-oxathiines and 2-acyl-5,6-dihydro-1,4-dioxines, important agents in medicinal and agricultural chemistry, from readily available thiiranes and oxiranes, respectively.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.