Dielectric relaxation and ac conductivity in magnetoelectric YCrO3 ceramics: A temperature dependent impedance spectroscopy analysis

Here, we report on the temperature and frequency dependent electrical conduction and dielectric behaviour of YCrO₃ ceramics. Dielectric studies reveal a peak in the dielectric constant ～230?K, suggesting presence of spin-charge coupling. Also, an additional broad peak found at ～450?K is reminiscent of a relaxor like behaviour for YCrO₃, attributed to a diffused phase transition. The nature of dc conductivity is of Arrhenius type and shows an abrupt change in the activation energy at ～230?K and ～450?K. The activation energy suggests that the polaronic hopping mechanism stabilizes at low temperature while, at higher temperatures, the process is associated with the diffusion of double ionized oxygen vacancies. However, ac conductivity suggests that the overlapping large polaron tunnelling conduction mechanism drives the ac conduction below 300?K and above 300?K, the conduction behaviour is consistent with the correlated barrier hopping conduction mechanism.     

Structural and electrical properties of sintered zinc-titanate ceramics

The aim of this work was an investigation of structural and electrical properties of sintered zinc-titanate ceramics obtained by mechanical activation. Mixtures of ZnO and TiO₂ were mechanically activated in a planetary ball mill up to 90 min and sintered isothermally in air for 120 min at 1100 °C. The phase composition in the ZnO–TiO₂ system after milling and sintering was analyzed using the XRD method. Microstructure analyses were performed using SEM. The results of electric resistivity, capacitance and loss tangent of the sintered samples were obtained. The existence of zinc-titanate as a dielectric was proved (?_r = 12.5, Q = 386.1, tgδ = 0.0026, ρ = 1.02 Ωm).     

Dielectric characteristics of donor-acceptor modified BaTiO3 ceramics

Sm/Mn codoped BaTiO₃ ceramics were investigated for their microstructure and dielectric characteristics. The powders were prepared by the conventional solid state procedure. The concentration of Sm₂O₃ as a donor dopant has been kept from 0.1 up to 5.0 at%. The content of MnO₂ as acceptor was kept constant at 0.05 at% Mn in all samples. The specimens were sintered at 1290 °C, 1320 °C and 1350 °C in an air atmosphere for two hours.A mainly uniform and homogeneous microstructure with average grain size ranging from 0.3 µm to 2.0 µm was observed in low doped samples. In highly doped samples, apart from the fine grained matrix, the appearance of local area with secondary abnormal grains was observed.The dielectric properties were investigated as a function of frequency and temperature. The low doped samples exhibit the high value of dielectric permittivity at room temperature and the greatest change at the Curie temperature. The highest value of dielectric constant (ε_r=6800) was measured for 0.1Sm/BaTiO₃ samples sintered at 1350 °C. A nearly flat permittivity-temperature response and lower values of ε_r were obtained in specimens with 2.0 and 5.0 at% additive content. The dielectric constant increases with the increase of sintering temperature. The dissipation factor ranged from 0.01 to 0.22 and decreases with the increase of sintering temperature. The Curie constant (C), Curie-Weiss temperature (T₀) and critical exponent of nonlinearity (γ ) were calculated using a Curie-Weiss and modified Curie-Weiss law. The highest value of Curie constant (C=9.06·10⁵ K) was measured in 0.1 at% doped samples. The Curie constant decreased with increasing dopant content. The γ values, ranging from 1.001 to 1.58, point out the sharp phase transition in low doped samples, and the diffuse phase transition in heavily doped BaTiO₃ samples.     

Synthesis and electrical conductivity of La-Sr-X-Mg-O (X = Ti, Zr, Al) perovskite solid solution

Perovskite solid solutions of (La_0.6Sr_0.4)(X_1−yMg_y)O_3−δ (X = Ti, Zr, Al) were prepared by a coprecipitation method using corresponding aqueous solutions and ammonium carbonate solution. The freeze-dried powders were sintered in air at 1000-1500 °C for 1-36 h. Single phase solid solutions were produced in the compositions of (La_0.6Sr_0.4)(Zr_0.6Mg_0.4)O_3−δ and (La_0.6Sr_0.4)(Al_0.9Mg_0.1)O_3−δ where (3 − δ) < 3. For the compositions of X = Ti and Zr for y = 0.1 where (3 − δ) > 3, two phases including perovskite solid solution were produced at 1400-1500 °C. The stability of perovskite solid solution was closely related to the fraction of lattice oxygen atom (3 − δ). A relatively high conductivity was measured for (La_0.6Sr_0.4)(Al_0.9Mg_0.1)O_3−δ (σ = 4.15 × 10⁻⁴ S/cm at 600 °C, activation energy 113.4 kJ/mol). The influence of fraction of oxide ion vacancy on the activation energy was small for δ = 0.1-0.3 of perovskite solid solution.     

Microstructure and electrical properties of zirconia and composite nanostructured ceramics sintered by different methods

The aim of this study is the preparation and characterization of dense cubic zirconia ceramics and zirconia nanocomposites (reinforced with 5 wt% alumina). The powders were obtained through sol–gel methods and densified using classical sintering and spark plasma sintering (SPS) methods. The obtained ceramics were characterized through X-ray diffraction, scanning electron microscopy and impedance spectroscopy at room and high temperature. The average grain size of cubic zirconia particles was found to be approximately 8 and 2.5 μm for the classical sintering and 99 nm for SPS. The alumina particles in composites have an average grain size of 0.7 μm for classical sintering and 53 nm for SPS ones. The total conductivity for nanocomposites sintered through both methods was also determined.     

Fabrication and electrical properties of Pb(Co1/3Nb2/3)O3 ceramics

Pb(Co_1/3Nb_2/3)O₃ (PCN) ceramics have been produced by sintering PCN powders synthesized from lead oxide (PbO) and cobalt niobate (CoNb₂O₆) with an effective method developed for minimizing the level of PbO loss during sintering. Attention has been focused on relationships between sintering conditions, phase formation, density, microstructural development, dielectric and ferroelectric properties of the sintered ceramics. From X-ray diffraction analysis, the optimum sintering temperature for the high purity PCN phase was found at approximately 1050 and 1100 °C. The densities of sintered PCN ceramics increased with increasing sintering temperature. However, it is also observed that at very high temperature the density began to decrease. PCN ceramic sintered at 1050 °C has small grain size with variation in grain shape. There is insignificant change of dielectric properties with sintering temperature. The P–E hysteresis loops observed at −70 °C are of slim-loop type with small remanent polarization values, which confirmed relaxor ferroelectric behavior of PCN ceramics.     

Effects of mechanical activation and two-step sintering on the structure and electrical properties of cordierite-based ceramics

The mechanical activation can help reduce production costs and modify cordierite-based materials. In this study, the structure and electrical properties of the mechanically activated MgO-Al₂O₃-SiO₂ system have been analyzed. The mixtures of MgO-Al₂O₃-SiO₂ powders were mechanically activated in a planetary ball mill for time periods ranging from 0 to 160 min. Structural investigations were performed on the obtained powders. The effects of activation and a two-step sintering process on the microstructure and crystal structure were investigated by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The thermal stability was analyzed using DTA. Electrical measurements showed variations of the dielectric constant (ε_r) and loss tangent (tan δ) as a function of the time of mechanical treatment.     

Structural,dielectric properties and electrical conduction behaviour of Dy substituted CaCu3Ti4O12 ceramics

Dy substituted CCTO ceramics were synthesized using solid state reaction method. Effect of Dy on structural, microstructural, dielectric and electrical properties has been studied over a wide temperature (300–500 K) and frequency range (100 Hz–1 MHz). Rietveld refinement, carried out on the samples, confirmed single phase formation and indicated overall decrease in lattice constant. Microstructure showed bimodal distribution of grains in CCTO with bigger grains surrounded by smaller grains. Dy substitution reduced grain size. Dy substitution in CCTO reduces the dielectric constant which may be attributed to increase of the Schottky potential barrier. The dielectric constant remains nearly constant in temperature range 300–400 K. The AC conductivity obeys a power law, σ_ac=A fⁿ, where n is the temperature dependent frequency exponent. The AC conductivity behaviour can be divided into three regions, over entire temperature range, depending on conduction processes. The relevant charge transport mechanisms have been discussed.     

Microstructure and electromagnetic properties of LiFe5O8 ferrite ceramics prepared from wet- and dry-milled powders

The effect of dry and wet ball milling of LiFe₅O₈ ferrite powder on the microstructure and electromagnetic properties of ferrite ceramics was studied using XRD analysis, scanning electron microscopy, dilatometry, thermogravimetry, calorimetry, and measurement of specific magnetization and electrical resistance. The sintering temperature was 1050 °C; the sintering time was 2 h. It was found that ferrite fabricated from dry-milled powder exhibits an ordered α-LiFe₅O₈ phase with bulk density of 91%. Its saturation magnetization and Curie temperature are 55 emu/g and 628°С, respectively. Specific electrical resistance is 4?10⁶ Ω cm. Wet milling in isopropyl alcohol causes formation of a disordered β-LiFe₅O₈ phase. Ceramics produced by this method shows higher bulk density (97%) and low porosity, and an order of magnitude lower resistivity. Its saturation magnetization and Curie temperature are 51 emu/g and 607°С, respectively.     

Dielectric relaxation behavior and energy storage properties in Ba0.4Sr0.6Zr0.15Ti0.85O3 ceramics with glass additives

Ba_0.4Sr_0.6Zr_0.15Ti_0.85O₃ ceramics with SrO–B₂O₃–SiO₂ glass additives were prepared via the solid state reaction route. The effects of glass contents on the sintering behavior, dielectric properties, microstructures, and energy storage properties of BSZT ceramics were investigated. Dielectric breakdown strength of 22.4 kV/mm was achieved for BSZT ceramics with 20 wt% glass addition. Dielectric relaxation behavior was observed in dielectric loss versus temperature plots. In order to investigate the mechanism of dielectric breakdown performance, the relationship between dielectric breakdown strength and grain boundary barrier was studied by the measurements of breakdown strength and activation energy. A discharged energy density of 0.45 J/cm³ with an energy efficiency of 88.2% was achieved for BSZT ceramics with 5 wt% glass addition.     

Effect of La substitution on the structural and electrical properties of BaBi4−xLaxTi4O15

Pure and lanthanum doped barium bismuth titanate BaBi_4−xLa_xTi₄O₁₅ (BBLT, x=0, 0.05, 0.15, 0.30) ceramics were prepared utilizing solid state method. The X-ray diffraction (XRD) data confirmed formation of single-phase Aurivillius compounds while SEM micrographs did not show evident grain size change of doped ceramics. Dielectric properties were investigated in 1.21 kHz to 1 MHz frequency range and in the temperature range of 20 to 727 °C. When Bi³⁺ is substituted with La³⁺, a significant disorder was induced and the material exhibited broadening of the phase transition. Impedance analysis confirmed the presence of two semicircular arcs in doped samples suggesting the existence of grain and grain-boundary conduction. The dc-conductivity and activation energies were evaluated for all compositions.     

Effect of consolidation parameters on structural,microstructural and electrical properties of magnesium titanate ceramics

The aim of this study is to explore the influence of the processing route on the structural and physical properties of bulk MgTiO₃ ceramics. Commercially available MgO and TiO₂ powders were mechanically activated in a planetary ball mill. Green bodies were formed by an isostatic pressure of 300 MPa. The sintering of these samples was done either by the Two-Step Sintering (TSS) approach or by conventional pressureless sintering followed by Hot Isostatic Pressing (post-HIPing). The first set of compacts was sintered by TSS in air at 1300 °C for 30 min and the next step was performed at 1200 °C for 20 h. The density of the obtained samples after the two-step sintering reached almost 90% of the theoretical density (%TD). The second set of compacts was sintered at 1400 °C for 30 min in air. The samples without open porosity were post-sintered by the HIP at 1200 °C for 2 h in an argon atmosphere at a pressure of 200 MPa. The density significantly increased up to 96%TD. The differences between samples prepared by these two techniques were also analyzed by XRD and SEM. The lattice vibration spectra were obtained using Raman spectroscopy and they indicate a high degree of lattice disorder, as well as high values of the oxygen vacancy concentration. Electrical characteristic were established in the frequency range from 10 kHz to 10 GHz. The choice of the processing route had considerable influence on structural and physical properties of MgTiO₃ ceramics.     

Fabrication of toughened B4C composites with high electrical conductivity using MAX phase as a novel sintering aid

MAX phase Ti₃AlC₂ was chosen as a novel sintering aid to prepare electrically conductive B₄C composites with high strength and toughness. Dense B₄C composites can be obtained at a hot-pressing temperature as low as 1850 °C with 15 vol% Ti₃AlC₂. The enhanced sinterability was mainly ascribed to the in situ reactions between B₄C and Ti₃AlC₂ as well as the liquid phase decomposed from Ti₃AlC₂. Both the Vickers hardness and fracture toughness increase with increasing Ti₃AlC₂ amount, and high hardness and toughness values of 28.5 GPa and 7.02 MPa m^−1/2 respectively were achieved for B₄C composites sintered with 20 vol% Ti₃AlC₂ at 1900 °C. Crack deflection by homogenously distributed TiB₂ particles was identified as the main toughening mechanism. Besides, B₄C composites sintered with Ti₃AlC₂ show significantly improved electrical conductivity due to the percolation of highly conductive TiB₂ phase, which could enhance the machinability of B₄C composites largely by allowing electrical discharge machining.     

Control of coring effect in BaTi4O9 microwave dielectric ceramics by doping with Mn4+

In the present work, we have attempted to reduce the effect of coring effect in the titanate ceramic system BaTi₄O₉ (BT4) by doping it with Mn⁴⁺. The microwave dielectric BaTi₄O₉ ceramics doped with 0, 0.5 and 1.0 mol% Mn⁴⁺ were synthesized by conventional ceramic processing route. The XRD studies confirmed a single phase crystalline structure for all the ceramic samples studied. The SEM micrographs of the ceramics reveal a microstructural change leading towards a more uniform grain size distribution as the Mn⁴⁺ content increases to 1.0 mol%. In the low frequency region (100 Hz to 1 MHz), the temperature stability of dielectric properties exhibits a marked improvement with the increasing amount of Mn⁴⁺ in the ceramic system. In the microwave frequency region (9.3 GHz), Q-factor increases from 11,625 GHz to 46,500 GHz for BaTi₄O₉ ceramic doped with 1.0 mol% Mn⁴⁺. The present paper reveals that the commonly observed degradation of dielectric properties due to coring effect in the BaTi₄O₉ ceramic system can be controlled by doping it with an appropriate quantity of Mn⁴⁺.     

Enhanced dielectric loss of Mg doped Ba0.7Sr0.3TiO3 ceramics

The effect of MgO doping on the structural, microstructural and dielectric properties of Ba_0.7Sr_0.3TiO₃ (BST) ceramic from the point of view of its application in microwave tunable devices has been studied. All the samples crystallize into perovskite structure. There is significant reduction in the value of loss factor with the increase in Mg-level, the dielectric constant and tunability are also reduced with the increase in Mg-level. Interestingly, the Fig. of merit of the material is found to be enhanced with increase of Mg-doping. The observed dielectric properties are explained on the basis of defect chemistry involved when Mg is doped in Ba_0.7Sr_0.3TiO₃ ceramics. The effect of dc field on the dielectric constant and the dielectric breakdown strength of the paraelectric phase Mg doped BST ceramic samples are also studied.     

Dielectric relaxation in calcium titanate-containing ceramics prepared by plasma spraying

The relative permittivity and loss factor frequency dependence in a weak electric field of plasma sprayed perovskite and ilminite polycrystalline ceramic materials—pure synthetic calcium titanate, as well as magnesium titanate—calcium titanate mixture, were studied. It was observed that plasma-sprayed titanates exhibit a strong relaxation of permittivity and loss factor decrease when they are measured in an as-sprayed state. The frequency dependence of the earlier properties is influenced by chemical composition and spraying parameters, but the relaxation character in general is preserved in all cases. The volume resistivity of the samples in an as-sprayed as well as subsequently annealed state was studied also. Several aspects of the structural features of plasma deposits and their possible influence on dielectric properties are discussed.     

Dielectric and impedance spectroscopy of Sr(Bi0.5Nb0.5)O3 ceramics

A lead free polycrystalline material Sr(Bi_0.5Nb_0.5)O₃ was prepared using a high-temperature solid-state reaction technique. Preliminary X-rays diffraction studies exhibit the formation of a single-phase compound in the orthorhombic crystal system. The study of microstructure of gold-coated pellet by scanning electron microscopy (SEM) shows well-defined and homogeneous distribution of grains on the surface of the sample. Detailed studies of dielectric parameters (i.e., ε_r and tan δ) of the compound as a function of temperature at selected frequencies reveal that the values of these parameters are almost independent of temperature. Studies of impedance and related parameters exhibit that these electrical properties of the material are strongly dependent on temperature, and bear a good correlation with the microstructure of the material. The decrease in value of bulk resistance on increasing temperature suggests the existence of negative temperature co-efficient of resistance (NTCR) in the material. Studies of electric modulus show the presence of hopping conduction mechanism in the material with non-exponential-type of relaxation. The nature of variation of dc conductivity with temperature confirms the Arrhenius- and NTCR- types of behaviors of the material. The ac conductivity spectrum provides a typical-signature of an ionic conducting system, and is found to obey Jonscher′s universal power law.     

Structural,electrical, magnetic and magnetoelectric properties of Fe doped BaTiO3 ceramics

In the present work structural, electrical, magnetic and magnetodielectric properties of BaTi_1−xFe_xO₃ (0%≤x≤10%) ceramics have been investigated. X-ray diffraction (XRD) study reveals that the coexistence of tetragonal and hexagonal phases is strongly influenced by Fe doping concentration. The increase in Fe-doping content leads to the development of hexagonal phase along with an increase in average grain size. A reduction in the dielectric properties is also observed. All BaTi_1−xFe_xO₃ (BTFO) compositions exhibit ferroelectric behavior at room temperature. Remnant polarization (P_r) for pure BaTiO₃ (BTO) has been found to be 7.50 µC/cm² and further decreases with an increase in the Fe concentration. All Fe doped samples exhibit ferromagnetic ordering with saturation magnetization (M_s) being 26 memu/g for x=2.5%. Further, at x=5%, it decreases and thereafter again increases with Fe concentration. The magnetodielectric coefficient increases with Fe doping concentration and highest value found to be 2.80 at x=2.5%.     

Low-temperature sintering and microwave dielectric properties of Ca5Co4(VO4)6 ceramics

A novel low temperature firing high Q microwave dielectric ceramic Ca₅Co₄(VO₄)₆ was prepared by the conventional solid-state reaction method. The phase purity, microstructure, and microwave dielectric properties were investigated. The Ca₅Co₄(VO₄)₆ ceramic sintered at 875 °C exhibited excellent microwave dielectric properties: Qxf = 95,200 GHz (at 10.6 GHz), τ_f = −63 ppm/°C, ɛ_r = 10.1, and its ɛ_r corrected for porosity was calculated as 11.1.