Superplastic flow in a nanostructured aluminum alloy produced using high-pressure torsion

Samples of a spray-cast Al-7034 alloy were processed by high-pressure torsion (HPT) at temperatures of 293 or 473 K using an imposed pressure of 4 GPa and torsional straining through five revolutions. Processing by HPT produced significant grain refinement with grain sizes of 60 and 85 nm at the edges of the disks for the two processing temperatures. In tensile testing at room temperature, the alloy processed by HPT exhibited higher strength and lower ductility than the unprocessed material. Good superplastic properties were achieved in tensile testing at elevated temperatures with a maximum elongation of 750% for the sample processed at 473 K and tested in tension at 703 K under an initial strain rate of 1.0 × 10⁻² s⁻¹. The measured superplastic elongations are lower than in samples prepared by equal-channel angular pressing because of the use of very thin disks in the HPT processing.     

Dielectric and electrostrictive properties of PMNT near MPB

The dielectric constant (ε_r), dielectric loss (tan δ) and strain induced by electric field in lead magnesium niobate–lead titanate (PMN-PT/PMNT) solid solutions in the morphotropic phase boundary (MPB) region at different sintering temperatures have been studied. ε_r and tan δ increase, whereas Curie phase transition range decreases with the increase in sintering temperature. Strain levels in the range of 0.07–0.2% were obtained. A high saturated strain% 0.19, a high d₃₃ coefficient 320 pm/V and a low strain hysteresis% 3.5 in PMNT 68/32 composition sintered at 1200 °C indicate its suitability for actuator applications.     

Evaluation of the strain-induced martensitic transformation by acoustic emission monitoring in 304L austenitic stainless steel: Identification of the AE signature of the martensitic transformation and power-law statistics

The aim of the present investigation is to characterize plasticity-induced martensite formation of metastable austenitic stainless steel at room temperature. Acoustic Emission (AE) monitoring is performed on a 304L austenitic stainless steel during fatigue tests. This work aims at identifying the acoustic emission signals associated with the formation of the strain-induced martensite. The present work includes the study of the influence of the specimen geometry. The use of statistical pattern recognition allowed the identification of the acoustic emission signatures for three mechanisms: dislocation motion, mechanical damage and martensitic transformation (MT). Moreover statistics on the energies of the AE signals were found to obey power laws (P(E)  E^−α) with exponent α = 1.75 ± 0.15 for the cluster associated with martensite formation.     

Mechanical and thermal properties of AlN–BN–SiC ceramics

Mechanical and thermal properties were characterized for two AlN:BN:SiC composite ceramics produced from BN with different particle sizes. The ceramics were hot pressed at temperatures from 1950 to 2100 °C to 97% relative density. For both materials, the matrix (90:10 vol% SiC:AlN) had a grain size of 0.4 μm, and the BN grains (10 vol%) were crystallographically aligned. Microhardness values were between 20 and 22 GPa, while fracture toughness values were between 2.5 and 3.1 MPa m^1/2. Other properties were found to be dependent on testing direction. Elastic moduli were between 260 and 300 GPa and strengths were 630 MPa for small particle BN additions. Thermal conductivity was calculated to be between 25 and 37 W/m K at room temperature and 17 and 25 W/m K at 900 °C. The low values compared to traditional SiC ceramics were attributed to AlN–SiC solid solution formation and sub-micron matrix grain sizes.     

Production of aluminum-matrix carbon nanotube composite using high pressure torsion

In this study, an Al-based composite containing carbon nanotubes (CNTs) was fabricated using a process of severe plastic deformation through high pressure torsion (HPT). Neither heating nor sintering was required with the HPT process so that an in situ consolidation was successfully achieved at ambient temperature with 98% of the theoretical density. A significant increase in hardness was recorded through straining by the HPT process. When the composite was pulled in tension, the tensile strength of more than 200 MPa was attained with reasonable ductility. Transmission electron microscopy showed that the grain size was reduced to 100 nm and this was much smaller than the grain size without CNTs and the grain size reported on a bulk sample. High resolution electron microscopy revealed that CNTs were present at grain boundaries. It was considered that the significant reduction in grain size is attributed to the presence of CNTs hindering the dislocation absorption and annihilation at grain boundaries.     

First-principles study of phase transition and structural properties of AlAs

We have investigated the phase transition and structural properties of AlAs in three crystallographic structures, i.e., B3 (zinc blende), B1 (rocksalt), and B8 (nickel arsenide), at high pressures using the full-potential linearized muffin-tin orbital (FP-LMTO) scheme within the generalized gradient approximation correction (GGA) in the frame of density functional theory (DFT). For B8 structure, it is found that the c/a ratios kept nearly constant (0.2% fluctuation) corresponding to V/V₀  0.7–1.05 (V is the primitive cell volume and V₀ is the experimental equilibrium volume of B3 structure), which is in full agreement with experiment, but the c/a ratios increase linearly with the values of V/V₀ decreasing corresponding to V/V₀  0.4–0.7. This indicates under low pressure the compression along c-axis and a-axis is the same, but the compression along c-axis is more difficult than along a-axis under higher pressure. Based on the condition of equal enthalpies AlAs is found to undergo a structural phase transition from B3 to B8 at 5.34 GPa, in agreement with the experimental value of 7 ± 5 GPa, and is speculated to undergo the B3–B1 transition at 6.24 GPa.     

From iron(III) precursor to magnetite and vice versa

The syntheses of nanosize magnetite particles by wet-chemical oxidation of Fe²⁺ have been extensively investigated. In the present investigation the nanosize magnetite particles were synthesised without using the Fe(II) precursor. This was achieved by γ-irradiation of water-in-oil microemulsion containing only the Fe(III) precursor. The corresponding phase transformations were monitored. Microemulsions (pH  12.5) were γ-irradiated at a relatively high dose rate of 22 kGy/h. Upon 1 h of γ-irradiation the XRD pattern of the precipitate showed goethite and unidentified low-intensity peaks. Upon 6 h of γ-irradiation, reductive conditions were achieved and substoichiometric magnetite (Fe_2.71O₄) particles with insignificant amount of goethite particles found in the precipitate. Hydrated electrons , organic radicals and hydrogen gas as radiolytic products were responsible for the reductive dissolution of iron oxide in the microemulsion and the reduction Fe³⁺ → Fe²⁺. Upon 18 h of γ-irradiation the precipitate exhibited dual behaviour, it was a more oxidised product than the precipitate obtained after 6 h of γ-irradiation, but it contained magnetite particles in a more reduced form (Fe_2.93O₄). It was presumed that the reduction and oxidation processes existed as concurrent competitive processes in the microemulsion. After 18 h of γ-irradiation the pH of the medium shifted from the alkaline to the acidic range. The high dose rate of 22 kGy/h was directly responsible for this shift to the acidic range. At a slightly acidic pH a further reduction of Fe³⁺ → Fe²⁺ resulted in the formation of more stoichiometric magnetite particles, whereas the oxidation conditions in the acidic medium permitted the oxidation Fe²⁺ → Fe³⁺. The Fe³⁺ was much less soluble in the acidic medium and it hydrolysed and recrystallised as goethite. The γ-irradiation of the microemulsion for 25 h at a lower dose rate of 16 kGy/h produced pure substoichiometric nanosize magnetite particles of about 25 nm in size and with the stoichiometry of Fe_2.83O₄.     

Influence of Cu addition on the self-propagating high-temperature synthesis of Ti5Si3 in Cu–Ti–Si system

The self-propagating high-temperature synthesis (SHS) reactions can take place in Cu–Ti–Si systems with Cu additions of 10–50 wt.%, and the products only consist of Ti₅Si₃ and Cu phases, without any transient phase. In Ti–Si system, most of the Ti₅Si₃ grains synthesized exhibit the polygon-shaped coarse appearance with an obviously sintered morphology. When Cu content increases from 10 to 50 wt.%, however, the Ti₅Si₃ exhibits cobblestone-like shape with a relatively smooth surface, and its average size decreases significantly from 15 to 2 μm or less. The formation mechanism of Ti₅Si₃ in Cu–Ti–Si system is characterized by the solution, reaction and precipitation processes. Furthermore, the addition of Cu has a great influence on the volume change between green and reacted preforms. The volume change increases with Cu content increasing from 0 to 20 wt.%, and then decreases with the content further increasing from 20 to 50 wt.%. The addition of Cu to Ti–Si system significantly decreases the onset temperature of the reaction during differential scanning calorimetry process, which is even much lower than the α → β transition temperature of Ti (882 °C), suggesting that the reaction could be greatly facilitated by Cu addition. As a result, the role of Cu serves not only as a diluent but also as a reactant and participates in the self-propagating high-temperature synthesis reaction process.     

Excitonic luminescence in ZnO nanopowders and ceramics

Fast photoluminescence spectra in the spectral region of 3.1–3.45 eV in ZnO and ZnO:Al ceramics were studied at 14 and 300 K. Ceramics with grains smaller than 100 nm were sintered from nanopowders by high pressure (8 GPa) and low temperature (350 °C). Ceramics with grain sizes 1–5 μm were sintered at 1400 °C. It is shown that excitonic luminescence spectra depend on the ceramics grain size, post preparing annealing and doping. The excitonic luminescence decay time was faster than 2 ns and the afterglow at 30 ns was 0.05%.     

Prediction of flow stress in Ti–6Al–4V alloy with an equiaxed α + β microstructure by artificial neural networks

Flow stress during hot deformation depends mainly on the strain, strain rate and temperature, and shows a complex and nonlinear relationship with them. A number of semi-empirical models were reported by others to predict the flow stress during hot deformation. This work attempts to develop a back-propagation neural network model to predict the flow stress of Ti–6Al–4V alloy for any given processing conditions. The network was successfully trained across different phase regimes (α + β to β phase) and various deformation domains. This model can predict the mean flow stress within an average error of 5.6% from the experimental values, using strain, strain rate and temperature as inputs. This model seems to have an edge over existing constitutive model, like hyperbolic sine equation, and has a great potential to be employed in industries.     

Influence of additives on the impact toughness of Al–10.8% Si near-eutectic cast alloys

This article investigates the effects of melt treatment and addition of alloying elements on the impact toughness of as-cast and heat-treated Al–10.8% Si near-eutectic alloys. Increasingly precise impact behaviors are discussed in the context of differentiating between initiation and propagation energies, including the ductility index, which is the ratio of the propagation to initiation energies; total energy as a useful measure is also discussed. Details concerning the evaluation of tensile properties are reported in a separate article [Mohamed AMA, Samuel FH, Samuel AM, Doty HW. Influence of additives on the microstructure and tensile properties of near-eutectic Al–10.8%Si cast alloy. Mater Des, in press]. The concentration of elements in the alloys was changed to the following range: Fe 0.5–1 wt%, Mn 0.5–1 wt%, Cu 2.25–3.25 wt%, and Mg 0.3–0.5 wt%, while the impact toughness upon artificial aging in a temperature range of 155–240 °C for 5 h was also investigated. The results indicate that the morphology of fibrous Si in Sr-modified alloys enhances toughness because of its profound effect on crack initiation and crack propagation resistance. The combined addition of modifier and grain refiner leads to a 33% increase in the impact strength compared to the untreated alloy. In alloys containing high levels of iron, such as the RF2 (1% Fe, 1% Mn) and RF4 (1% Fe, 0.5% Mn) alloys, the addition of iron leads to an increased precipitation of sludge or β-Fe platelets, respectively; these particles also act as crack initiation sites and reduce the impact properties noticeably. In alloys already containing high levels of copper, such as the RC2 (3.25% Cu, 0.3% Mg) and RC5(0.3.25% Cu, 0.5% Mg) alloys, increasing the copper level lowers the impact properties significantly, in view of the fact that the fracture behavior is now predominantly influenced by the Al₂Cu phase rather than by the Si particles. The average crack propagation speed of impact-tested samples shows a good inverse relationship to impact energy. Crack propagation speed can thus provide a qualitative estimation of the impact energy expected for special alloy conditions.     

Low-temperature fabrication of 0.65 PMN–0.35 PT by a mixed oxide method

Single-phase perovskite 0.65 PMN–0.35 PT was achieved at low temperature by a conventional mixed oxide method. It was prepared by ball-milling a mixture of PbO(orthorhombic), TiO₂, Nb₂O₅ and (MgCO₃)₄Mg(OH)₂·5H₂O instead of MgO and heat treatment at 800 °C for 2 h. The formation was studied by means of DSC, FT-IR, Coupled TG-Mass, XRD, and SEM. It proceeded via formation of PbO(tetragonal) and Pb₂Nb₂O₇(P₂N) intermediates to form perovskite phase. The pure perovskite PMN-PT powder was obtained in particle size of 0.5–0.8 μm, agglomerate-free, and pseudo-cube. The powder calcined at 600 °C was sintered to 97% T.D. at 900–1000 °C for 2 h and showed room temperature dielectric constant of 3200, loss of 1–2%, and specific resistance of 5 × 10¹¹ Ω cm.     

Superplastic behavior of a fine-grained ZK60 magnesium alloy processed by high-ratio differential speed rolling

Grain size of the ZK60 alloy was effectively reduced to 12 μm through high-ratio differential speed rolling (HRDSR) for a thickness reduction of 70% in a single pass. Due to the strengthening effects of grain boundaries and particles, the HRDSR processed ZK60 exhibited a high tensile strength of 340 MPa. Low temperature superplasticity was attained at 473–493 K at low strain rates (5 × 10⁻⁴ s⁻¹) and high strain rate superplasticity was attained at 523–553 K at high strain rates (10⁻² s⁻¹). The optimum superplastic temperature was found to be 553 K where a maximum tensile elongation of 1000% was obtained at 1 × 10⁻³ s⁻¹. The deformation behavior of the HRDSR processed ZK60 at elevated temperatures could be depicted by considering contribution of grain boundary sliding and slip creep to total plastic flow. Difference in superplastic deformation behavior between the HRDSR processed and equal channel angular press processed ZK60 alloys was examined and discussed.     

Transformation mismatch plasticity in Pd induced by cyclic hydrogen charging

Transformation mismatch plasticity is achieved in swaged palladium wires by cyclical hydriding–dehydriding. Upon multiple cycles at ambient temperature, a total strain of 40% is accumulated under a constant tensile stress. This value is much higher than the tensile ductility for swaged Pd subjected to monotonic deformation without transformation (<2% for this wire). Strain increments after a single cycle are proportional to the applied stress, in agreement with the Greenwood–Johnson equation for transformation mismatch plasticity. The yield stress of hydrogen-cycled Pd calculated from this equation is 760 MPa, which is much higher than the value of the original wire and about 50% higher than previous values reported for Pd that was hydrogen cycled at 100 °C without an applied stress.     

Microstructure and mechanical properties of nanocrystalline high strength Al–Mg–Si (AA6061) alloy by high energy ball milling and spark plasma sintering

In the present paper, the microstructure and mechanical properties of nanostructured Al–Mg–Si based AA6061 alloy obtained by high energy ball milling and spark plasma sintering were reported. Gas atomized microcrystalline powder of AA6061 alloy was ball milled under wet condition at room temperature to obtain nanocrystalline powder with grain size of 30 nm. The nanocrystalline powder was consolidated to fully dense compacts by spark plasma sintering (SPS) at 500 °C. The grain size after SPS consolidation was found to be 85 nm. The resultant SPS compacts exhibited microhardness of 190–200 HV_100 g, compressive strength of 800 MPa and strain to fracture of 15%.     

Nano-crystalline LaFeO3 powders synthesized by the citrate–gel method

A novel sol–gel process was developed for preparing nano-sized, perovskite-type LaFeO₃ powder by the thermal decomposition of the gel-complex of LaFe–(C₆H₈O₇·H₂O). The structural evolution has been systematically investigated by X-ray diffraction (XRD), differential thermal analysis (DTA) and thermogravimetric analysis (TGA). Perovskite powder of  25 nm size could be obtained at a temperature of  600 °C without formation of any secondary phases of La₂O₃ and Fe₂O₃ single oxides and no requirements of high temperature/vacuum/pH control etc. Analysis of the X-ray powder diffraction data showed a decrease in the value of lattice strains with increasing decomposition temperature, whereas the particle size increases with increasing decomposition temperature.     

Dynamic recrystallization during high temperature deformation of magnesium

As a consequence of the high critical stresses required for the activation of non-basal slip systems, dynamic recrystallization plays a vital role in the deformation of magnesium, particularly at a deformation temperature of 200 °C, where a transition from brittle to ductile behavior is observed. Uniaxial compression tests were performed on an extruded commercial magnesium alloy AZ31 at different temperatures and strain rates to examine the influence of deformation conditions on the dynamic recrystallization (DRX) behavior and texture evolution. Furthermore, the role of the starting texture in the development of the final DRX grain size was investigated. The recrystallized grain size, measured at large strains (  −1.4) seemed to be more dependent on the deformation conditions than on the starting texture. In contrast to pure magnesium, AZ31 does not undergo grain growth at elevated deformation temperatures, i.e. 400 °C, even at a low strain rate of 10⁻⁴ s⁻¹. Certain deformation conditions gave rise to a desired fully recrystallized microstructure with an average grain size of 18 μm and an almost random crystallographic texture. For samples deformed at 200 °C/10⁻² s⁻¹, optical microscopy revealed DRX inside of deformation twins, which was further investigated by EBSD.     

Forging of Mg–3Al–1Zn–1Ca alloy prepared by high-frequency electromagnetic casting

The 1 wt.%Ca–AZ31 alloy produced by electromagnetic casting (EMC) in presence of electromagnetic stirring (EMS) was extruded and then subjected to the closed-die forging to make a pulley for automobile application. Effective dynamic recrystallization (DRX) took place during the forging process, leading to formation of fully recrystallized grains with the average size of 3–4 μm. High-forging ability and high degree of grain refinement achieved during the forging were attributed to the novel microstructure of the cast composed of small and equiaxed grains with the average size of 50 μm and thin layer (Al, Mg)₂ Ca phase at grain boundaries, which would provide more nucleation sites and a faster rate of recrystallization during deformation by forging as compared to that of the conventionally processed cast composed of large size grains and thick layer (Al, Mg)₂ Ca phase. The forged pulley exhibited the ultimate tensile strength of 273–286 MPa with tensile elongations of 30%. The present result demonstrates a possibility that EMC + EMS techniques can be used in producing magnesium feed stocks with high-forging ability.     

The influence of Yb doping on the upconversion luminescence of Pr in aluminum oxide based powders prepared by combustion synthesis

The effect of ytterbium (Yb³⁺) doping on the upconversion (UC) emission of praseodymium (Pr³⁺) doped in aluminum oxide based powders prepared by combustion synthesis is reported for near-infrared excitation (λ = 980 nm). Our experimental results show that the crystalline structure and the UC emission changes with the Yb³⁺ concentration. The sample containing only Pr³⁺ (1.0 wt.%) did not show any UC signal and the UC emission profiles of the samples containing Pr³⁺ (1.0 wt.%) and Yb³⁺ (0.5, 2.0 wt.%) are quite different. The sample containing 0.5 wt.% of Yb³⁺ has five emission lines in the visible range associated to Pr³⁺ 4f–4f transitions, ³P₀ → ³H₄ (497 nm), ³P₀ → ³H₅ (525 and 550 nm), ³P₀ → ³H₆ (620 nm) and ³P₀ → ³F₂ (650 nm). We believe that the UC process has its origin in energy transfer from Yb³⁺ ions to Pr³⁺ ions in Pr_0.83Al_11.83O₁₉ phase. The sample containing 2.0 wt.% of Yb³⁺ has only one emission line in the visible range peaked at 507 nm which we believe has its origin in cooperative UC emission due to excited Yb³⁺ pairs in YbAlO₃ phase. The samples containing Yb³⁺ also present UC emission lines in the near-infrared which are assigned to intrinsic lattice defects.     

Visualization of emitting sites on carbon fiber cathode by surface treatment in high-current vacuum discharge process

In this paper, a carbon fiber cathode, having robust, easily shaped, and epoxy-free properties, is constructed by squeeze casting technique that can overcome some disadvantages of conventional methods. Carbon fiber emitters on the cathode surface had a high distribution density, thus ensuring sufficient emission centers or emission uniformity. The fabricated cathode was tested in a diode powered by a 350 kV, 40 Ω, 400 ns high-voltage pulse generator. The turn-on electric field was estimated to be 50 kV/cm, and the field enhancement factor was (1.2–2.0) × 10³. It was found that the electron emission of carbon fiber cathode is initiated from the individual bright spots at a current density of up to 400 A/cm². Most notably, the X-ray images of electron beam on anode foil demonstrate the development of bright spots on the cathode surface. As a whole, this class of cathodes can endure high-current pulsed emission, and has a positive application prospect.