Acid-catalyzed production of biodiesel from waste frying oil

The reaction kinetics of acid-catalyzed transesterification of waste frying oil in excess methanol to form fatty acid methyl esters (FAME), for possible use as biodiesel, was studied. Rate of mixing, feed composition (molar ratio oil:methanol:acid) and temperature were independent variables. There was no significant difference in the yield of FAME when the rate of mixing was in the turbulent range 100 to 600 rpm. The oil:methanol:acid molar ratios and the temperature were the most significant factors affecting the yield of FAME. At 70 °C with oil:methanol:acid molar ratios of 1:245:3.8, and at 80 °C with oil:methanol:acid molar ratios in the range 1:74:1.9–1:245:3.8, the transesterification was essentially a pseudo-first-order reaction as a result of the large excess of methanol which drove the reaction to completion (99±1% at 4 h). In the presence of the large excess of methanol, free fatty acids present in the waste oil were very rapidly converted to methyl esters in the first few minutes under the above conditions. Little or no monoglycerides were detected during the course of the reaction, and diglycerides present in the initial waste oil were rapidly converted to FAME.     

Biodiesel from Jojoba oil-wax: Transesterification with methanol and properties as a fuel

The Jojoba oil-wax is extracted from the seeds of the Jojoba (Simmondsia chinensis Link Schneider), a perennial shrub that grows in semi desert areas in some parts of the world. The main uses of Jojoba oil-wax are in the cosmetics and pharmaceutical industry, but new uses could arise related to the search of new energetic crops.This paper summarizes a process to convert the Jojoba oil-wax to biodiesel by transesterification with methanol, catalysed with sodium methoxide (1 wt% of the oil). The transesterification reaction has been carried out in an autoclave at 60 °C, with a molar ratio methanol/oil 7.5:1, and vigorous stirring (600 rpm), reaching a quantitative conversion of the oil after 4 h. The separation of the fatty acid methyl esters (the fraction rich in FAME, 79% FAME mixture; 21% fatty alcohols; 51% of methyl cis-11-eicosenoate) from the fatty alcohols rich fraction (72% fatty alcohols; 28% FAME mixture; 26% of cis-11-eicosen-1-ol, 36% of cis-13-docosen-1-ol) has been accomplished in a single crystallization step at low temperature (−18 °C) from low boiling point petroleum ether.The fraction rich in FAME has a density (at 15 °C), a kinematic viscosity (at 40 °C), a cold filter plugging point and a high calorific value in the range of the European standard for biodiesel (EN 14214).     

Effects of water on the esterification of free fatty acids by acid catalysts

To maximize the production of biodiesel from soybean soapstock, the effects of water on the esterification of high-FFA (free fatty acid) oils were investigated. Oleic acid and high acid acid oil (HAAO) were esterified by reaction with methanol in the presence of Amberlyst-15 as a heterogeneous catalyst or sulfuric acid as a homogeneous catalyst. The yield of fatty acid methyl ester (FAME) was studied at oil to methanol molar ratios of 1:3 and 1:6 and reaction temperatures of 60 and 80 °C. The rate of esterification of oleic acid significantly decreased as the initial water content increased to 20% of the oil. The activity of Amberlyst-15 decreased more rapidly than that of sulfuric acid, due to the direct poisoning of acid sites by water. Esterification using sulfuric acid was not affected by water until there was a 5% water addition at a 1:6 molar ratio of oil to methanol. FAME content of HAAO prepared from soapstock rapidly increased for the first 30 min of esterification. Following the 30-min mark, the rate of FAME production decreased significantly due to the accumulation of water. When methanol and Amberlyst-15 were removed from the HAAO after 30 min of esterification and fresh methanol and a catalyst were added, the time required to reach 85% FAME content was reduced from 6 h to 1.8 h.     

Biodiesel production by esterification of palm fatty acid distillate

Production of fatty acid methyl ester (FAME) from palm fatty acid distillate (PFAD) having high free fatty acids (FFA) was investigated in this work. Batch esterifications of PFAD were carried out to study the influence of: including reaction temperatures of 70–100 °C, molar ratios of methanol to PFAD of 0.4:1–12:1, quantity of catalysts of 0–5.502% (wt of sulfuric acid/wt of PFAD) and reaction times of 15–240 min. The optimum condition for the continuous esterification process (CSTR) was molar ratio of methanol to PFAD at 8:1 with 1.834 wt% of H₂SO₄ at 70 °C under its own pressure with a retention time of 60 min. The amount of FFA was reduced from 93 wt% to less than 2 wt% at the end of the esterification process. The FAME was purified by neutralization with 3 M sodium hydroxide in water solution at a reaction temperature of 80 °C for 15 min followed by transesterification process with 0.396 M sodium hydroxide in methanol solution at a reaction temperature of 65 °C for 15 min. The final FAME product met with the Thai biodiesel quality standard, and ASTM D6751-02.     

Biodiesel production from palm oil via heterogeneous transesterification

This paper presents the study of the transesterification of palm oil via heterogeneous process using montmorillonite KSF as heterogeneous catalyst. This study was carried out using a design of experiment (DOE), specifically response surface methodology (RSM) based on four-variable central composite design (CCD) with α (alpha) = 2. The transesterification process variables were reaction temperature, x₁ (50–190 °C), reaction period, x₂ (60–300 min), methanol/oil ratio, x₃ (4–12 mol mol^?1) and amount of catalyst, x₄ (1–5 wt%). It was found that the yield of palm oil fatty acid methyl esters (FAME) could reach up to 79.6% using the following reaction conditions: reaction temperature of 190 °C, reaction period at 180 min, ratio of methanol/oil at 8:1 mol mol^?1 and amount of catalyst at 3%.     

Application of response surface methodology for optimizing transesterification of Moringa oleifera oil: Biodiesel production

Response surface methodology (RSM), with central composite rotatable design (CCRD), was used to explore optimum conditions for the transesterification of Moringa oleifera oil. Effects of four variables, reaction temperature (25–65 °C), reaction time (20–90 min), methanol/oil molar ratio (3:1–12:1) and catalyst concentration (0.25–1.25 wt.% KOH) were appraised. The quadratic term of methanol/oil molar ratio, catalyst concentration and reaction time while the interaction terms of methanol/oil molar ratio with reaction temperature and catalyst concentration, reaction time with catalyst concentration exhibited significant effects on the yield of Moringa oil methyl esters (MOMEs)/biodiesel, p < 0.0001 and p < 0.05, respectively. Transesterification under the optimum conditions ascertained presently by RSM: 6.4:1 methanol/oil molar ratio, 0.80% catalyst concentration, 55 °C reaction temperature and 71.08 min reaction time offered 94.30% MOMEs yield. The observed and predicted values of MOMEs yield showed a linear relationship. GLC analysis of MOMEs revealed oleic acid methyl ester, with contribution of 73.22%, as the principal component. Other methyl esters detected were of palmitic, stearic, behenic and arachidic acids. Thermal stability of MOMEs produced was evaluated by thermogravimetric curve. The fuel properties such as density, kinematic viscosity, lubricity, oxidative stability, higher heating value, cetane number and cloud point etc., of MOMEs were found to be within the ASTM D6751 and EN 14214 biodiesel standards.     

Biodiesel production from Jatropha curcas oil

In view of the fast depletion of fossil fuel, the search for alternative fuels has become inevitable, looking at huge demand of diesel for transportation sector, captive power generation and agricultural sector, the biodiesel is being viewed a substitute of diesel. The vegetable oils, fats, grease are the source of feedstocks for the production of biodiesel. Significant work has been reported on the kinetics of transesterification of edible vegetable oils but little work is reported on non-edible oils. Out of various non-edible oil resources, Jatropha curcas oil (JCO) is considered as future feedstocks for biodiesel production in India and limited work is reported on the kinetics of transesterification of high FFA containing oil. The present study reports a review of kinetics of biodiesel production. The paper also reveals the results of kinetics study of two-step acid–base catalyzed transesterification process carried out at pre-determined optimum temperature of 65 and 50 °C for esterification and transesterification process, respectively, under the optimum condition of methanol to oil ratio of 3:7 (v/v), catalyst concentration 1% (w/w) for H₂SO₄ and NaOH and 400 rpm of stirring. The yield of methyl ester (ME) has been used to study the effect of different parameters. The maximum yield of 21.2% of ME during esterification and 90.1% from transesterification of pretreated JCO has been obtained. This is the first study of its kind dealing with simplified kinetics of two-step acid–base catalyzed transesterification process carried at optimum temperature of both the steps which took about 6 h for complete conversion of TG to ME.     

Biodiesel from palm oil via loading KF/Ca–Al hydrotalcite catalyst

The solid base catalyst KF/Ca–Al hydrotalcite was obtained from Ca–Al layered double hydroxides and successfully used in the transesterification of methanol with palm oil to produce biodiesel. With the load of KF, the activity of Ca–Al mixed-oxides had been improved much. For the mass ratio 80 wt.%(KF·6H₂O to Ca–Al mixed-oxides) catalyst, under the optimal condition: 338 K, catalyst amount 5%(wt./wt. oil) and methanol/oil molar ratio 12:1, after 5 h reaction, the fatty acid methyl esters yield could reach 97.98%; for the mass ratio 100 wt.%(KF·6H₂O to Ca–Al mixed-oxides) ones, under the same reaction condition, only needed 3 h to get the FAME yield of 99.74%, and even only reacted 1 h, the FAME yield could obtain 97.14%.     

Biodiesel production from jatropha oil (Jatropha curcas) with high free fatty acids: An optimized process

Response surface methodology (RSM) based on central composite rotatable design (CCRD) was used to optimize the three important reaction variables—methanol quantity (M), acid concentration (C) and reaction time (T) for reduction of free fatty acid (FFA) content of the oil to around 1% as compared to methanol quantity (M′) and reaction time (T′) and for carrying out transesterification of the pretreated oil. Using RSM, quadratic polynomial equations were obtained for predicting acid value and transesterification. Verification experiments confirmed the validity of both the predicted models. The optimum combination for reducing the FFA of Jatropha curcas oil from 14% to less than 1% was found to be 1.43% v/v H₂SO₄ acid catalyst, 0.28 v/v methanol-to-oil ratio and 88-min reaction time at a reaction temperature of 60 °C as compared to 0.16 v/v methanol-to-pretreated oil ratio and 24 min of reaction time at a reaction temperature of 60 °C for producing biodiesel. This process gave an average yield of biodiesel more than 99%. The fuel properties of jatropha biodiesel so obtained were found to be comparable to those of diesel and confirming to the American and European standards.     

Screening,optimization and kinetics of Jatropha curcas oil transesterification with heterogeneous catalysts

This work investigates the production of fatty acid methyl esters (FAME) from Jatropha curcas oil using a variety of heterogeneous catalysts: resins, zeolites, clays, hydrotalcites, aluminas and niobium oxide. For this purpose, a catalyst screening was first conducted in a batch reactor at the following operating conditions: oil to methanol molar ratio of 1:9, 6 h of reaction, 5 wt% catalyst, at 333 and 393 K. From the screening step, KSF clay and Amberlyst 15 catalysts were selected to carry out a 2³ full factorial central composite rotatable design so as to elucidate the effects of process variables on FAME yield. The optimum reaction conditions for both catalysts were found to be oil to methanol molar ratio of 1:12, 5 wt% of catalyst, 433 K and 6 h of reaction with a FAME yield of about 70 wt%. A kinetic study was then experimentally performed and a semi-empirical model was built to represent the experimental data. Finally, catalyst re-utilization in five successive batch experiments was evaluated at the optimized conditions.     

Continuous esterification for biodiesel production from palm fatty acid distillate using economical process

An overflow system for continuous esterification of palm fatty acid distillate (PFAD) using an economical process was developed using a continuous stirred tank reactor (CSTR). Continuous production compared to batch production at the same condition had higher product purity. The optimum condition for the esterification process was a 8.8:1:0.05 molar ratio of methanol to PFAD to sulfuric acid catalyst, 60 min of residence time at 75 °C under its own pressure. The free fatty acid (FFA) content in the PFAD was reduced from 93 to less than 1.5%wt by optimum esterification. The esterified product had to be neutralized with 10.24%wt of 3 M sodium hydroxide in water solution at a reaction temperature of 80 °C for 20 min to reduce the residual FFA and glycerides. The components and properties of fatty acid methyl ester (FAME) could meet the standard requirements for biodiesel fuel. Eventually the production costs were calculated to disclose its commercialization.     

Esterification of high FFA tung oil with solid acid catalyst in fixed bed reactor

The effect of molar ratio of methanol to oil, temperature and space velocity (SV) on pre-esterification of Tung oil was carried out in pilot-scale fixed bed reactor, with solid acid catalysts. The molar ratio results showed the maximum acid value reduction efficiency (90.21%) was obtained at the molar ratio of 8:1, the acid value decreased sharply to 0.70 g kg^?1 of KOH. And esterification reaction attained balance when space velocity was enough, so 0.029 h^?1 was optimal space velocity. Furthermore, activity of reactant and rate of reaction increase with temperature increased, and the maximum conversion was achieved at 65 °C, the acid value of Tung oil could be reduced to 1.4 g kg^?1 of KOH.     

Production of biodiesel catalyzed by immobilized Pseudomonas cepacia lipase from Sapium sebiferum oil in micro-aqueous phase

A new technique of biodiesel production from Sapium sebiferum oil catalyzed by immobilized lipase from Pseudomonas cepacia G63 prepared in our laboratory was investigated in this study. The independent factors were studied and the significant factors to the yield of biodeisel were confirmed, and the Box–Behnken design was employed to evaluate the effects of those significant factors on yield in preparation of biodiesel. Results indicated the optimal condition for biodiesel preparation were: 4:1 methano/oil molar ratio, 2.7% (w/w) lipase, temperature 41 °C, and the subsequent verification experiment got a result of (96.22%) kept coincided with the predicted biodiesel yield (97.07%) under the optimal conditions, and R² = 98.19% shown the model was considered to be accurate and available for predicting the yield of biodiesel. There was no loss nearly in the immobilized lipase activity after being repeatedly used for 20 cycles at the optimal reaction condition.     

Biodiesel fuel production with solid amorphous-zirconia catalysis in fixed bed reactor

Amorphous zirconia catalysts, titanium-, aluminum-, and potassium-doped zirconias, were prepared and evaluated in the transesterification of soybean oil with methanol at 250 °C, and the esterification of n-octanoic acid with methanol at 175–200 °C. Titanium- and aluminum-doped zirconias are promising solid catalysts for the production of biodiesel fuels from soybean oil because of their high performance, with over 95% conversion in both of the esterifications.     

Comparison of biodiesel production from crude Jatropha oil and Krating oil by supercritical methanol transesterification

This work compared the production of biodiesel from two different non-edible oils with relatively high acid values (Jatropha oil and Krating oil). Using non-catalytic supercritical methanol transesterification, high methyl ester yield (85–90%) can be obtained in a very short time (5–10 min). However, the dependence of fatty acid methyl ester yield on reaction conditions (i.e., temperature and pressure) and the optimum conditions were different by the source of oils and were correlated to the amount of free fatty acids (FFAs) and unsaturated fatty acid content in oils. Krating oil, which has higher FFAs and unsaturated fatty acid content, gave higher fatty acid methyl ester yield of 90.4% at 260 °C, 16 MPa, and 10 min whereas biodiesel from Jatropha oil gave fatty acid methyl ester yield of 84.6% at 320 °C, 15 MPa and 5 min using the same molar ratio of methanol to oil 40:1. The product quality from crude Krating oil met the biodiesel standard. Pre-processing steps such as degumming or oil purification are not necessary.     

Kinetic model for the esterification of oleic acid catalyzed by zinc acetate in subcritical methanol

The esterification of oleic acid in subcritical methanol catalyzed by zinc acetate was investigated in a batch-type autoclave. The effect of reaction conditions such as temperature, pressure, reaction time and molar ratio of oleic acid to methanol on the esterification was examined. The oleic acid conversion reached 95.0% under 220 °C and 6.0 MPa with the molar ratio of methanol to oleic acid being 4 and 1.0 wt% zinc acetate as catalyst. A kinetic model for the esterification was established. By fitting the kinetic model with the experimental results, the reaction order n = 2.2 and activation energy E_a = 32.62 KJ/mol were obtained.     

Lithium ion impregnated calcium oxide as nano catalyst for the biodiesel production from karanja and jatropha oils

Lithium impregnated calcium oxide has been prepared by wet impregnation method in nano particle form as supported by powder X-ray diffraction and transmission electron microscopy. Basic strength of the same was measured by Hammett indicators. Calcium oxide impregnated with 1.75 wt% of lithium was used as solid catalyst for the transesterification karanja and jatropha oil, containing 3.4 and 8.3 wt% of free fatty acids, respectively. The reaction parameters, viz., reaction temperature, alcohol to oil molar ratio, free fatty acid contents, amount of catalyst and amount of impregnated lithium ion in calcium oxide support, have been studied to establish the most suitable condition for the transesterification reaction. The complete transesterification of karanja and jatropha oils was achieved in 1 and 2 h, respectively, at 65 °C, utilizing 12:1 molar ratio of methanol to oil and 5 wt% (catalyst/oil, w/w) of catalyst. Few physicochemical properties of the prepared biodiesel samples have been studied and compared with standard values.     

Production of FAME by palm oil transesterification via supercritical methanol technology

The present study employed non-catalytic supercritical methanol technology to produce biodiesel from palm oil. The research was carried out in a batch-type tube reactor and heated beyond supercritical temperature and pressure of methanol, which are at 239 °C and 8.1 MPa respectively. The effects of temperature, reaction time and molar ratio of methanol to palm oil on the yield of fatty acid methyl esters (FAME) or biodiesel were investigated. The results obtained showed that non-catalytic supercritical methanol technology only required a mere 20 min reaction time to produce more than 70% yield of FAME. Compared to conventional catalytic methods, which required at least 1 h reaction time to obtain similar yield, supercritical methanol technology has been shown to be superior in terms of time and energy consumption. Apart from the shorter reaction time, it was found that separation and purification of the products were simpler since no catalyst is involved in the process. Hence, formation of side products such as soap in catalytic reactions does not occur in the supercritical methanol method.     

Transesterified Hingan (Balanites) oil as a fuel for compression ignition engines

The study endeavor to utilize esters of Balanites aegyptiaca (L.) Del(Balanites) as a fuel for diesel engine. Ester developed from balanites oil by the transesterification process is investigated for its properties and the engine performance. A single stage alkali-catalyzed esterification process by using 1.25% KOH, methyl alcohol 8:1 molar ratio with respect to balanites oil, gives the maximum ester yield of 95%. The performance and emission characteristics of the engine are analyzed using balanites oil methyl esters and diesel as fuel. The viscosity of balanites oil is found to be decreased by 89% after esterification, and the calorific value of balanites oil methyl esters is nearly 94% of the diesel fuel. The engine performance with balanites oil methyl ester as a fuel resembles to that of conventional diesel fuel, while the exhaust gas emissions are reduced with the use of balanites oil methyl esters.     

Production of biodiesel fuels from linseed oil using methanol and ethanol in non-catalytic SCF conditions

Methyl and ethyl esters as biodiesel fuels were prepared from linseed oil with transesterification reaction in non-catalytic supercritical fluids conditions. Biodiesel fuel is a renewable substitute fuel for petroleum diesel fuel made from vegetable or animal fats. Biodiesel fuel has better properties than that of petroleum diesel fuel such as renewable, biodegradable, non-toxic, and essentially free of sulfur and aromatics. The purpose of the transesterification process is to lower the viscosity of the oil. The viscosity values of linseed oil methyl and ethyl esters highly decreases after transesterification process. The viscosity values of vegetable oils vary between 27.2 and 53.6 mm² s^?1, whereas those of vegetable oil methyl esters between 3.59 and 4.63 mm² s^?1. Compared with no. 2 diesel fuel, all of the vegetable oil methyl esters were slightly viscous. The flash point values of vegetable oil methyl esters are highly lower than those of vegetable oils. The transesterification of linseed oil in supercritical fluids such as methanol and ethanol has proved to be the most promising process. Methanol is the commonly used alcohol in this process, due in part to its low cost. Methyl esters of vegetable oils have several outstanding advantages among other new-renewable and clean engine fuel alternatives. The most important variables affecting the methyl ester yield during the transesterification reaction are molar ratio of alcohol to vegetable oil and reaction temperature. Biodiesel has become more attractive recently because of its environmental benefits. Biodiesel is an environmentally friendly fuel that can be used in any diesel engine without modification.