Controlling eutrophication by combined bloom precipitation and sediment phosphorus inactivation

The hypothesis that the combination of the flocculent polyaluminium chloride (PAC) with the lanthanum-modified bentonite Phoslock^® (Flock & Lock) could sink effectively a water bloom of cyanobacteria and could shift a turbid, cyanobacteria infested lake to a clear water lake was tested in a controlled laboratory experiment and a whole lake experiment. In the laboratory, a relatively low dose of the flocculent PAC (2.2 and 4.4 mg Al l⁻¹) was insufficient to sediment positively buoyant cyanobacteria (Microcystis aeruginosa). Similarly, the lanthanum modified clay (dosed at 390 mg l⁻¹) was insufficient to sediment the positively buoyant cyanobacteria. However, the combination of PAC and Phoslock^® effectively sedimented cyanobacteria flocks. Likewise, a combined treatment of 2 tons PAC and 18 tons Phoslock^® in Lake Rauwbraken in April 2008 effectively sedimented a developing cyanobacteria bloom of Aphanizomenon flos-aquae. The average chlorophyll-a concentration in the two years prior to this Flock & Lock treatment was 19.5 (±36.5) μg l⁻¹, while it was as low as 3.7 (±4.5) μg l⁻¹ in the years following the treatment. The combined treatment effectively reduced the amount of total phosphorus (TP) in the water column from on average 169 (±126) μg P l⁻¹ before the application to 14 (±15) μg P l⁻¹ after the treatment. Based on mean summer chlorophyll-a and TP concentrations, the lake was shifted from a eutrophic/hypertrophic state to an oligo/mesotrophic state. From directly after treatment in April 2008 until and including 2013, Lake Rauwbraken remained in an oligo-mesotrophic clear water state with TP reduced to less than 10% of the pre-treatment. This result shows that eutrophication in relatively small, isolated, stratifying lakes can be restored by targeting both water column and sediment P using a combination of flocculent and solid phase P-sorbent.     

Controlling toxic cyanobacteria: effects of dredging and phosphorus-binding clay on cyanobacteria and microcystins

Sediment dredging and Phoslock^® addition were applied individually and in combination in an enclosure experiment in a Dutch hypertrophic urban pond. These measures were applied to control eutrophication and reduce the risk of exposure to cyanobacterial toxins. Over the 58 days course of the experiment, cyanobacteria (predominantly Microcystis aeruginosa) gradually decreased until they dropped below the level of detection in the combined treated enclosures, they were reduced in dredged enclosures, but remained flourishing in controls and Phoslock^® treated enclosures. Cyanobacteria were, however, less abundant in the enclosures (medians chlorophyll-a 30-87 μg l⁻¹) than in the pond (median chlorophyll-a 162 μg l⁻¹), where also a thick surface scum covered one-third of the pond for many weeks.Soluble reactive phosphorus (SRP), total phosphorus and total nitrogen concentrations were significantly lower in the combined dredged and Phoslock^® treated enclosures than in controls. Median SRP concentrations were 24 μg P l⁻¹ in the combined treatment, 58 μg P l⁻¹ in dredged enclosures, and 90 μg P l⁻¹ in controls and 95 μg P l⁻¹ in Phoslock^® treated enclosures. Hence, the combined treatment was most effective in decreasing SRP and TP, and in lowering cyanobacterial biomass.Microcystin (MC) concentrations were analyzed by LC-MS/MS. MC concentrations and cyanobacterial biomass were positively correlated in all treatments. Mean MC concentrations in controls (71 μg l⁻¹), Phoslock^® treated enclosures (37 μg l⁻¹) and dredged enclosures (25 μg l⁻¹) exceeded the provisional guideline of 20 μg l⁻¹, whereas mean MC concentrations were 13 μg l⁻¹ in the combined treated enclosures. All samples contained the MC variants dmMC-RR, MC-RR, MC-YR, dmMC-LR and MC-LR; traces of MC-LY and nodularin were detected in few samples. The different treatments did not change the relative contribution of the variants to the MC pool; MC profiles in all treatments and the pond showed dominance of MC-RR followed by MC-LR. In the surface scum of the pond, total MC concentration was extremely high (64000 μg l⁻¹ or 1300 μg g⁻¹ DW), which poses a serious health hazard to children playing on the banks of the pond. Based on our results and pond characteristics, we propose combined sediment dredging and Phoslock^® addition, fish removal and strong reduction of duck feeding by the neighborhood as most promising measures controlling cyanobacterial hazards in this pond.     

Lake responses following lanthanum-modified bentonite clay (Phoslock) application: An analysis of water column lanthanum data from 16 case study lakes

Phoslock^® is a lanthanum (La) modified bentonite clay that is being increasingly used as a geo-engineering tool for the control of legacy phosphorus (P) release from lake bed sediments to overlying waters. This study investigates the potential for negative ecological impacts from elevated La concentrations associated with the use of Phoslock^® across 16 case study lakes. Impact-recovery trajectories associated with total lanthanum (TLa) and filterable La (FLa) concentrations in surface and bottom waters were quantified over a period of up to 60 months following Phoslock^® application. Both surface and bottom water TLa and FLa concentrations were <0.001 mg L⁻¹ in all lakes prior to the application of Phoslock^®. The effects of Phoslock^® application were evident in the post-application maximum TLa and FLa concentrations reported for surface waters between 0.026 mg L⁻¹–2.30 mg L⁻¹ and 0.002 mg L⁻¹ to 0.14 mg L⁻¹, respectively. Results of generalised additive modelling indicated that recovery trajectories for TLa and FLa in surface and bottom waters in lakes were represented by 2nd order decay relationships, with time, and that recovery reached an end-point between 3 and 12 months post-application. Recovery in bottom water was slower (11–12 months) than surface waters (3–8 months), most probably as a result of variation in physicochemical conditions of the receiving waters and associated effects on product settling rates and processes relating to the disturbance of bed sediments. CHEAQS PRO modelling was also undertaken on 11 of the treated lakes in order to predict concentrations of La³⁺ ions and the potential for negative ecological impacts. This modelling indicated that the concentrations of La³⁺ ions will be very low (<0.0004 mg L⁻¹) in lakes of moderately low to high alkalinity (>0.8 mEq L⁻¹), but higher (up to 0.12 mg L⁻¹) in lakes characterised by very low alkalinity. The effects of elevated La³⁺ concentrations following Phoslock^® applications in lakes of very low alkalinity requires further evaluation. The implications for the use of Phoslock^® in eutrophication management are discussed.     

Temporal variations in arsenic uptake by rice plants in Bangladesh: The role of iron plaque in paddy fields irrigated with groundwater

The transfer of arsenic to rice grains is a human health issue of growing relevance in regions of southern Asia where shallow groundwater used for irrigation of paddy fields is elevated in As. In the present study, As and Fe concentrations in soil water and in the roots of rice plants, primarily the Fe plaque surrounding the roots, were monitored during the 4-month growing season at two sites irrigated with groundwater containing ∼ 130 μg l^− 1 As and two control sites irrigated with water containing < 15 μg l^− 1 As. At both sites irrigated with contaminated water, As concentrations in soil water increased from < 10 μg l^− 1 to > 1000 μg l^− 1 during the first five weeks of the growth season and then gradually declined to < 10 μg l^− 1 during the last five weeks. At the two control sites, concentrations of As in soil water never exceeded 40 µg l^− 1. At both contaminated sites, the As content of roots and Fe plaque rose to 1000-1500 mg kg^− 1 towards the middle of the growth season. It then declined to ∼ 300 mg kg^− 1 towards the end, a level still well above As concentration of ∼ 100 mg kg^− 1 in roots and plaque measured throughout the growing season at the two control sites. These time series, combined with simple mass balance considerations, demonstrate that the formation of Fe plaque on the roots of rice plants by micro-aeration significantly limits the uptake of As by rice plants grown in paddy fields. Large variations in the As and Fe content of plant stems at two of the sites irrigated with contaminated water and one of the control sites were also recorded. The origin of these variations, particularly during the last month of the growth season, needs to be better understood because they are likely to influence the uptake of As in rice grains.     

Sublethal toxicity of commercial insecticide formulations and their active ingredients to larval fathead minnow (Pimephales promelas)

Toxic effect concentrations of insecticides are generally determined using the technical grade or pure active ingredient. Commercial insecticide formulations, however, contain a significant proportion (> 90%) of so-called inert ingredients, which may alter the toxicity of the active ingredient(s). This study compares the sublethal toxicity of two insecticides, the pyrethroid bifenthrin, and the phenylpyrazole fipronil, to their commercial formulations, Talstar® and Termidor®. Both insecticides are used for landscape treatment and structural pest control, and can be transported into surface water bodies via stormwater and irrigation runoff. We used larval fathead minnow (Pimephales promelas), to determine effects on growth and swimming performance after short-term (24 h) exposure to sublethal concentrations of pure insecticides and the respective formulations. Significantly enhanced 7 d growth was observed at 10% of the 24 h LC₁₀ (53 μg L⁻¹) fipronil. Swimming performance was significantly impaired at 20% of the 24 h LC₁₀ (0.14 μg L⁻¹) of bifenthrin and 10% of the 24 h LC₁₀ of Talstar® (0.03 μg L⁻¹). Fipronil and Termidor® led to a significant impairment of swimming performance at 142 μg L⁻¹ and 148 μg L⁻¹ respectively, with more pronounced effects for the formulation. Our data shows that based on dissolved concentrations both formulations were more toxic than the pure active ingredients, suggesting that increased toxicity due to inert ingredients should be considered in risk assessments and regulation of insecticides.     

Changes in water quality of the River Frome (UK) from 1965 to 2009: is phosphorus mitigation finally working?

The water quality of the River Frome, Dorset, southern England, was monitored at weekly intervals from 1965 until 2009. Determinands included phosphorus, nitrogen, silicon, potassium, calcium, sodium, magnesium, pH, alkalinity and temperature. Nitrate-N concentrations increased from an annual average of 2.4 mg l^− 1 in the mid to late 1960s to 6.0 mg l^− 1 in 2008-2009, but the rate of increase was beginning to slow. Annual soluble reactive phosphorus (SRP) concentrations increased from 101 μg l^− 1 in the mid 1960s to a maximum of 190 μg l^− 1 in 1989. In 2002, there was a step reduction in SRP concentration (average = 88 μg l^− 1 in 2002-2005), with further improvement in 2007-2009 (average = 49 μg l^− 1), due to the introduction of phosphorus stripping at sewage treatment works. Phosphorus and nitrate concentrations showed clear annual cycles, related to the timing of inputs from the catchment, and within-stream bioaccumulation and release. Annual depressions in silicon concentration each spring (due to diatom proliferation) reached a maximum between 1980 and 1991, (the period of maximum SRP concentration) indicating that algal biomass had increased within the river. The timing of these silicon depressions was closely related to temperature. Excess carbon dioxide partial pressures (EpCO₂) of 60 times atmospheric CO₂ were also observed through the winter periods from 1980 to 1992, when phosphorus concentration was greatest, indicating very high respiration rates due to microbial decomposition of this enhanced biomass. Declining phosphorus concentrations since 2002 reduced productivity and algal biomass in the summer, and EpCO₂ through the winter, indicating that sewage treatment improvements had improved riverine ecology. Algal blooms were limited by phosphorus, rather than silicon concentration. The value of long-term water quality data sets is discussed. The data from this monitoring programme are made freely available to the wider science community through the CEH data portal (http://gateway.ceh.ac.uk/).     

Multiple site study of recent atmospheric metal (Pb, Zn and Cu) deposition in the NW Iberian Peninsula using peat cores

In order to estimate atmospheric metal deposition in Southern Europe since the beginning of the Industrial Period (~ 1850 AD), concentration profiles of Pb, Zn and Cu were determined in four ²¹⁰Pb-dated peat cores from ombrotrophic bogs in Serra do Xistral (Galicia, NW Iberian Peninsula). Maximum metal concentrations varied by a factor of 1.8 for Pb and Zn (70 to 128 μg g⁻¹ and 128 to 231 μg g⁻¹, respectively) and 3.5 for Cu (11 to 37 μg g⁻¹). The cumulative metal inventories of each core varied by a factor of 3 for all analysed metals (132 to 329 μg cm⁻² for Pb, 198 to 625 μg cm⁻² for Zn and 22 to 69 μg cm⁻² for Cu), suggesting differences in net accumulation rates among peatlands. Although results suggest that mean deposition rates vary within the studied area, the enhanced ²¹⁰Pb accumulation and the interpretation of the inventory ratios (²¹⁰Pb/Pb, Zn/Pb and Cu/Pb) in two bogs indicated that either a record perturbation or post-depositional redistribution effects must be considered. After correction, Pb, Zn and Cu profiles showed increasing concentrations and atmospheric fluxes since the mid-XX^th century to maximum values in the second half of the XX^th century. For Pb, maximum fluxes were observed in 1955-1962 and ranged from 16 to 22 mg m⁻² yr⁻¹ (mean of 18 ± 1 mg m⁻² yr⁻¹), two orders of magnitude higher than in the pre-industrial period. Peaks in Pb fluxes in Serra do Xistral before the period of maximum consumption of leaded petrol in Europe (1970s-1980s) suggest the dominance of local pollutant sources in the area (i.e. coal mining and burning). More recent peaks were observed for Zn and Cu, with fluxes ranging from 32 to 52 mg m⁻² yr⁻¹ in 1989-1996, and from 4 to 9 mg m⁻² yr⁻¹ in 1994-2001, respectively. Our results underline the importance of multi-core studies to assess both the integrity and reliability of peat records, and the degree of homogeneity in bog accumulation. We show the usefulness of using the excess ²¹⁰Pb inventory to distinguish between differential metal deposition, accumulation or anomalous peat records.     

Comparison of toxicity and release rates of Cu and Zn from anti-fouling paints leached in natural and artificial brackish seawater

Biocide-containing anti-fouling paints are regulated and approved according to the added active ingredients, such as Cu. Biocide-free paints are considered to be less environmentally damaging and do not need an approval. Zn, a common ingredient in paints with the potential of causing adverse effects has received only minor attention. Laboratory experiments were conducted in artificial brackish seawater (ASW) and natural brackish seawater (NSW) to quantify release rates of Cu and Zn from biocide-containing and biocide-free labeled eroding anti-fouling paints used on commercial vessels as well as leisure boats. In addition, organisms from three trophic levels, the crustacean Nitocra spinipes, the macroalga Ceramium tenuicorne and the bacteria Vibrio fischeri, were exposed to Cu and Zn to determine the toxicity of these metals. The release rate of Cu in NSW was higher from the paints for professional use (3.2-3.6 µg cm⁻² d^− 1) than from the biocide leaching leisure boat paint (1.1 µg cm⁻² d^− 1). Biocide-free paints did leach considerably more Zn (4.4-8.2 µg cm⁻² d^− 1) than biocide-containing leisure boat paint (3.0 µg cm⁻² d^− 1) and ship paints (0.7-2.0 µg cm⁻² d^− 1). In ASW the release rates of both metals were notably higher than in NSW for most tested paints. The macroalga was the most sensitive species to both Cu (EC₅₀ = 6.4 µg l^− 1) and Zn (EC₅₀ = 25 µg l^− 1) compared to the crustacean (Cu, LC₅₀ = 2000 µg l^− 1 Zn, LC₅₀ = 890 µg l^− 1), and the bacteria (Cu, EC₅₀ = 800 µg l^− 1 and Zn, EC₅₀ = 2000 µg l^− 1). The results suggest that the amounts of Zn and Cu leached from anti-fouling paints may attain toxic concentrations in areas with high boat density. To fully account for potential ecological risk associated with anti-fouling paints, Zn as well as active ingredients should be considered in the regulatory process.     

Water, vegetation and sediment gradients in submerged aquatic vegetation mesocosms used for low-level phosphorus removal

Gradients in phosphorus (P) removal and storage were investigated over 6 years using mesocosms (each consisting of three tanks in series) containing submerged aquatic vegetation (SAV) grown on muck and limerock (LR) substrates. Mean inflow total P concentrations (TP) of 32 μg L⁻¹ were reduced to 15 and 17 μg L⁻¹ in the muck and LR mesocosms, respectively. Mesocosm P loading rates (mean = 1.75 g m⁻² year⁻¹) varied widely during the study and were not correlated with outflow TP, which instead varied seasonally with lowest monthly mean values in December and January.The mesocosms initially were stocked with Najas guadalupensis, Ceratophyllum demersum, and Chara zeylanica, but became dominated by C. zeylanica. At the end of the study, highest vegetative biomass (1.1 and 1.4 kg m⁻² for muck and LR substrates) and tissue P content (1775 and 1160 mg kg⁻¹) occurred in the first tank in series, and lowest biomass (1.0 and 0.2 kg m⁻²) and tissue P (147 and 120 mg kg⁻¹) in the third tank. Sediment accretion rates (2.5, 1.9 and 0.9 cm yr⁻¹ on muck substrates), accrued sediment TP (378, 309 and 272 mg kg⁻¹), and porewater soluble reactive P (SRP) concentrations (40, 6 and 4 μg L⁻¹) in the first, second and third tanks, respectively, exhibited a similar decreasing spatial trend. Plant tissue calcium (Ca) near mesocosm inflow (19-30% dry weight) and outflow (23-26%) were not significantly different, and sediment Ca was also similar (range of 24 to 28%) among sequential tanks.Well-defined vegetation and sediment enrichment gradients developed in SAV wetlands operated under low TP conditions. While the mesocosm data did not reflect deterioration in treatment performance over 6 years, accumulation of P-enriched sediments near the inflow could eventually compromise hydraulic storage and P removal effectiveness of these shallow systems.     

Effect of COD/SO(4)(2-) ratio and sulfide on thermophilic (55 degrees C) sulfate reduction during the acidification of sucrose at pH 6

This study investigated the effect of the COD/SO₄²⁻ ratio (4 and 1) and the sulfide concentration on the performance of thermophilic (55 °C) acidifying (pH 6) upflow anaerobic sludge bed reactors fed with sucrose at an organic loading rate of 4.5 g COD l_reactor⁻¹ day⁻¹. Sulfate reduction efficiencies amounted to 65% and 25-35% for the COD/SO₄²⁻ ratios of 4 and 1, respectively. Acidification was complete at all the tested conditions and the electron flow was similar at the two COD/SO₄²⁻ ratios applied. The stepwise decrease of the sulfide concentrations in the reactors with a COD/SO₄²⁻ ratio of 1 by N₂ stripping caused an immediate stepwise increase in the sulfate reduction efficiencies, indicating a reversible inhibition by sulfide. The degree of reversibility was, however, affected by the growth conditions of the sludge. Acidifying sludge pre-grown at pH 6, at a COD/SO₄²⁻ ratio of 9 and exposed for 150 days to 115 mg l⁻¹ sulfide, showed a slower recovery from the sulfide inhibition than a freshly harvested sludge from a full scale treatment plant (pH 7 and COD/SO₄²⁻=9.5) exposed for a 70 days to 200 mg l⁻¹ sulfide. In the latter case, the decrease of the sulfide concentration from 200 to 45 mg l⁻¹ (35 mg l⁻¹ undissociated sulfide) by N₂ stripping caused an immediate increase of the sulfate reduction efficiency from 35% to 96%.     

Threshold concentrations of biomass and iron for pressure drop increase in spiral-wound membrane elements

In a model feed channel for spiral-wound membranes the quantitative relationship of biomass and iron accumulation with pressure drop development was assessed. Biofouling was stimulated by the use of tap water enriched with acetate at a range of concentrations (1-1000 μg C l⁻¹). Autopsies were performed to quantify biomass concentrations in the fouled feed channel at a range of Normalized Pressure Drop increase values (NPD_i). Active biomass was determined with adenosinetriphosphate (ATP) and the concentration of bacterial cells with Total Direct Cell count (TDC). Carbohydrates (CH) were measured to include accumulated extracellular polymeric substances (EPS). The paired ATP and CH concentrations in the biofilm samples were significantly (p < 0.001; R² = 0.62) correlated and both parameters were also significantly correlated with NPD_i (p < 0.001). TDC was not correlated with the pressure drop in this study. The threshold concentration for an NPD_i of 100% was 3.7 ng ATP cm⁻² and for CH 8.1 μg CH cm⁻². Both parameters are recommended for diagnostic membrane autopsy studies. Iron concentrations of 100-400 mg m⁻² accumulated in the biofilm by adsorption were not correlated with the observed NPD_i, thus indicating a minor role of Fe particulates at these concentrations in fouling of spiral-wound membrane.     

The intake of lead and associated metals by sheep grazing mining-contaminated floodplain pastures in mid-Wales, UK: II. Metal concentrations in blood and wool

Sheep grazing metal-contaminated floodplain pastures across mid-Wales ingest high concentrations of lead (Pb) in vegetation and directly in the form of soil. Sheep whole blood analysis indicated that Pb concentrations can be significantly elevated for animals grazing contaminated sites: in winter/spring, a median blood concentration of 147 µg Pb l^− 1 was found at the location with the highest soil enrichment of this metal compared to only 26 µg Pb l^− 1 for the control flock. There was within-flock variability in blood-Pb concentration, and overlap between blood-Pb ranges in animals grazing control and contaminated sites, although use of the Kruskal-Wallis H test established a number of significant (P < 0.05) differences between the blood-Pb content of flocks grazing the various study locations. Despite total daily intakes of up to 723 mg Pb d^− 1, only one individual sheep showed a blood-Pb content above the ‘normal safe’ concentration of 250 µg l^− 1. Blood and wool analyses were found to have limited value for the diagnosis of environmental exposure to Pb, and further consideration of metal accumulation in offal, bone and muscle tissue is recommended.     

Ecotoxicological assessment of a polyelectrolyte flocculant

Flocculant blocks are commonly used as a component of (passive) water treatment systems to reduce suspended sediment loads in the water column. This study investigated the potential for aquatic biological impacts of a flocculant block formulation that contained an anionic polyacrylamide (PAM) active ingredient and a polyethylene glycol (PEG) based carrier. The toxicity of the whole flocculant block was assessed and the individual components of the block were also tested separately. Five Northern Australian tropical freshwater species (i.e. Chlorella sp. Lemna aequinoctialis, Hydra viridissima, Moinodaphnia macleayi and Mogurnda mogurnda) were exposed to a range of concentrations of the whole flocculant block, and of the individual PAM and PEG components. The concentration of Total Organic Carbon (TOC) in solution was used to provide a measure of the total amount of PAM and PEG present. An extremely wide range of toxic responses were found, with the flocculant blocks being essentially non-toxic to the duckweed, fish and algae (IC₅₀ > 1880 mg l⁻¹ C TOC, IC₁₀ > 460 mg l⁻¹ C TOC), slightly toxic to the hydra (IC₅₀ = 610-2180 mg l⁻¹ C TOC, IC₁₀ = 80-60 mg l⁻¹ C TOC) and significantly more toxic to the cladoceran (IC₅₀ = 10 mg l⁻¹ C TOC, IC₁₀ = 4 mg l⁻¹ C TOC). More detailed investigation of the two components indicated that the PAM was the primary “toxicant” in the flocculant blocks. Derived Protective Concentrations (PCs) for the flocculant blocks, expressed as equivalent TOC concentrations, were found to be lower than typically measured natural environmental concentrations of TOC. It will thus be possible to use TOC as measure of the concentration of PAM only in those situations where lower levels of ecosystem protection (i.e. higher PCs) are applicable.     

Yield of trihalomethanes and haloacetic acids upon chlorinating algal cells, and its prediction via algal cellular biochemical composition

The major objective of the present study was to investigate the contribution of major biomolecules, including protein, carbohydrates and lipids, in predicting DBPs formation upon chlorination of algal cells. Three model compounds, including bovine serum albumin (BSA), starch and fish oil, as surrogates of algal-derived proteins, carbohydrates and lipids, and cells of three algae species, representing blue-green algae, green algae, and diatoms, were chlorinated in the laboratory. The results showed that BSA (27 μg mg⁻¹ C) and fish oil (50 μg mg⁻¹ C) produced more than nine times higher levels of chloroform than starch (3 μg mg⁻¹ C). For the formation of HAAs, BSA was shown to have higher reactivity (49 μg mg⁻¹ C) than fish oil and starch (5 μg mg⁻¹ C). For the algal cells, Nitzschia sp. (diatom) showed higher chloroform yields (48 μg mg⁻¹ C) but lower HAA yields (43 μg mg⁻¹ C) than Chlamydomonas sp. (green algae) (chloroform: 34 μg mg⁻¹ C; HAA: 62 μg mg⁻¹ C) and Oscillatoria sp. (blue-green algae) (chloroform: 26 μg mg⁻¹ C; HAA: 72 μg mg⁻¹ C). The calculated chloroform formation of cells from the three algal groups, based on their biochemical compositions, was generally consistent with the experimental data, while the predicted values for HAAs were significantly lower than the observed ones. As compared to humic substances, such as humic and fulvic acids, the algal cells appeared to be important precursors of dichloroacetic acid.     

Nitrogen and phosphorus removal from an abattoir wastewater in a SBR with aerobic granular sludge

The formation and performance of granular sludge was studied in an 8 l sequencing batch reactor (SBR) treating an abattoir (slaughterhouse) wastewater. Influent concentrations averaged 1520 mg l⁻¹ volatile suspended solids (VSS), 7685 mg l⁻¹ Chemical oxygen demand (COD), 1057 mg l⁻¹ total kjeldahl nitrogen (TKN), 217 mg l⁻¹ total P. The COD loading was 2.6 kg m⁻³ d⁻¹. The SBR was seeded with flocculating sludge from a SBR with an 1 h settle time, but granules developed within 4 days by reducing the settle time to 2 min. The SBR cycle also had 120 min mixed (anaerobic) fill, 220 min aerated react, and 18 min draw/idle. The granules had a mean diameter of 1.7 mm, a specific gravity of 1.035, a density of 62 g VSS l⁻¹, a zone settling velocity (ZSV) of 51 m h⁻¹, and a sludge volume index (SVI) of 22 ml g⁻¹. Without optimizing process conditions, removal of COD and P were over 98%, and removal of N and VSS were over 97%. Nitrification and denitrification occurred simultaneously during react. The results indicate that conventional SBRs treating wastewaters with flocculating sludge can be converted to granular SBRs by reducing the settle time.     

A comprehensive assessment of PM emissions from paved roads: Real-world Emission Factors and intense street cleaning trials

Compliance with air quality standards requires control of source emissions: fine exhaust particles are already subject to regulation but vehicle fleets increase whilst the non-exhaust emissions are totally uncontrolled. Emission inventories are scarce despite their suitability for researchers and regulating agencies for managing air quality and PM reduction measures. Only few countries in Europe proposed street cleaning as a possible control measure, but its effectiveness is still far to be determined.This study offers first estimates of Real-world Emission Factors for PM₁₀ and brake-wear elements and the effect on PM₁₀ concentrations induced by intense street cleaning trials.A straightforward campaign was carried out in the city of Barcelona with hourly elemental composition of fine and coarse PM to detect any short-term effect of street cleaning on specific tracers of non-exhaust emissions. Samples were analyzed by Particle Induced X-Ray Emission.Real-world Emission Factor for PM₁₀ averaged for the local fleet resulted to be 97 mg veh^− 1 km^− 1. When compared to other European studies, our EF resulted higher than what found in UK, Germany, Switzerland and Austria but lower than Scandinavian countries. For brake-related elements, total EFs were estimated, accounting for the sum of direct and resuspension emissions, in 7400, 486, 106 and 86 μg veh^− 1 km^− 1, respectively for Fe, Cu, Sn and Sb. In PM_2.5Fe and Cu emission factors were respectively 4884 and 306 μg veh^− 1 km^− 1.Intense street cleaning trials evidenced a PM₁₀ reduction at kerbside of 3 μg m^− 3 (mean daily levels of 54 μg m^− 3), with respect to reference stations. It is important to remark that such benefit could only be detected in small time-integration periods (12:00-18:00) since in daily values this benefit was not noticed. Hourly PM elemental monitoring allowed the identification of mineral and brake-related metallic particles as those responsible of the PM₁₀ reduction.     

Atmospheric NH3 and NO2 concentration and nitrogen deposition in an agricultural catchment of Eastern China

To assess the atmospheric environmental impacts of anthropogenic reactive nitrogen in the fast-developing Eastern China region, we measured atmospheric concentrations of nitrogen dioxide (NO₂) and ammonia (NH₃) as well as the wet deposition of inorganic nitrogen (NO₃⁻ and NH₄⁺) and dissolved organic nitrogen (DON) levels in a typical agricultural catchment in Jiangsu Province, China, from October 2007 to September 2008_. The annual average gaseous concentrations of NO₂ and NH₃ were 42.2 μg m⁻³ and 4.5 μg m⁻³ (0 °C, 760 mm Hg), respectively, whereas those of NO₃⁻, NH₄⁺, and DON in the rainwater within the study catchment were 1.3, 1.3, and 0.5 mg N L⁻¹, respectively. No clear difference in gaseous NO₂ concentrations and nitrogen concentrations in collected rainwater was found between the crop field and residential sites, but the average NH₃ concentration of 5.4 μg m⁻³ in residential sites was significantly higher than that in field sites (4.1 μg m⁻³). Total depositions were 40 kg N ha⁻¹ yr⁻¹ for crop field sites and 30 kg N ha⁻¹ yr⁻¹ for residential sites, in which dry depositions (NO₂ and NH₃) were 7.6 kg N ha⁻¹ yr⁻¹ for crop field sites and 1.9 kg N ha⁻¹ yr⁻¹ for residential sites. The DON in the rainwater accounted for 16% of the total wet nitrogen deposition. Oxidized N (NO₃⁻ in the precipitation and gaseous NO₂) was the dominant form of nitrogen deposition in the studied region, indicating that reactive forms of nitrogen created from urban areas contribute greatly to N deposition in the rural area evaluated in this study.     

Cultured phototrophic biofilms for phosphorus removal in wastewater treatment

Culture experiments with phototrophic biofilms taken from the sedimentation tank of the wastewater treatment plant at the Fiumicino Airport in Rome, Italy were carried out in a prototype continuous flow incubator. Biofilms grown at varying photosynthetic photon flux density (PPFD), temperature and flow velocity were sampled at three developmental stages to quantify biofilm dry weight, chlorophyll a concentration and total cellular phosphorus content. While no coherent significant effects by flow and temperature were evidenced, maximum biofilm dry weight and phosphorous concentration significantly increased across all featured PPFDs. Maximum chlorophyll a concentration was saturated above 60 μmol m⁻² s⁻¹. A highly significant association between organic biomass and phosphorous content was observed for most light conditions, including a larger proportional increase of phosphorus concentration with respect to chlorophyll a at high PPFD. Up to 112 mg P m⁻² d⁻¹ maximal phosphorous removal rates were achieved. Elemental analysis by energy filtering transmission electron microscopy showed subcellular localization of phosphorus, confirming the accumulation in phototrophic microorganisms in biofilms grown in high light conditions.     

Biomonitoring of Cd, Cr, Hg and Pb in the Baluarte River basin associated to a mining area (NW Mexico)

With the purpose of knowing seasonal variations of Cd, Cr, Hg and Pb in a river basin with past and present mining activities, elemental concentrations were measured in six fish species and four crustacean species in Baluarte River, from some of the mining sites to the mouth of the river in the Pacific Ocean between May 2005 and March 2006. In fish, highest levels of Cd (0.06 μg g^− 1 dry weight) and Cr (0.01 μg g^− 1) were detected during the dry season in Gobiesox fluviatilis and Agonostomus monticola, respectively; the highest levels of Hg (0.56 μg g^− 1) were detected during the dry season in Guavina guavina and Mugil curema. In relation to Pb, the highest level (1.65 μg g^− 1) was detected in A. monticola during the dry season. In crustaceans, highest levels of Cd (0.05 μg g^− 1) occurred in Macrobrachium occidentale during both seasons; highest concentration of Cr (0.09 μg g^− 1) was also detected in M. occidentale during the dry season. With respect to Hg, highest level (0.20 μg g^− 1) was detected during the rainy season in Macrobrachium americanum; for Pb, the highest concentration (2.4 μg g^− 1) corresponded to Macrobrachium digueti collected in the dry season. Considering average concentrations of trace metals in surficial sediments from all sites, Cd (p < 0.025), Cr (p < 0.10) and Hg (p < 0.15) were significantly higher during the rainy season. Biota sediment accumulation factors above unity were detected mostly in the case of Hg in fish during both seasons. On the basis of the metal levels in fish and crustacean and the provisional tolerable weekly intake of studied elements, people can eat up to 13.99, 0.79 and 2.34 kg of fish in relation to Cd, Hg and Pb, respectively; regarding crustaceans, maximum amounts were 11.33, 2.49 and 2.68 kg of prawns relative to levels of Cd, Hg and Pb, respectively.     

Phosphorus sorption experiments and the potential for internal phosphorus loading in littoral areas of a stratified lake

The exchange of phosphorus (P) during the resuspension of sediments into shallow (oxic) waters of deep stratified lakes is regulated by equilibrium dynamics. In this study, we compared the P-sorption characteristics of sediments from 17 shallow and deep littoral sites in an oligo-mesotrophic lake. Zero Equilibrium P Concentration (EPC₀) ranged from 0.2 to 5 μg P L⁻¹. EPC₀ did not vary with sediment characteristics, but increased with increasing sediment-to-water ratios (SWR). Buffering capacity also increased with increasing SWR up to 1 g L⁻¹, at which point P concentrations were buffered almost perfectly. Therefore, internal P loading in littoral areas may depend primarily on the intensity and duration of sediment resuspension instead of sediment composition, and is expected to be spatially and temporally patchy. Maximum P-sorption capacity (S_max) varied with chemical composition of the sediments, but was generally low, indicating a limited capacity of littoral sediments to retain external inputs of P.