离子渗氮AISI 420马氏体不锈钢耐蚀行为研究

采用不同温度对AISI 420马氏体不锈钢进行离子渗氮处理.借助光学显微镜和X射线衍射(XRD)技术分析了渗氮层的微观组织结构,利用显微硬度计测试了渗氮层的硬度分布,通过电化学极化曲线测试和盐雾腐蚀试验研究了离子渗氮AISI 420不锈钢在模拟工业环境中的腐蚀行为.结果表明:AISI 420不锈钢350℃低温离子渗氮层由ε-Fe3N和N过饱和固溶体αN相组成,其化学稳定性高,加之固溶Cr元素的联合作用,明显提高了AISI 420不锈钢基材的腐蚀抗力.AISI 420钢经450℃和550℃渗氮处理,渗氮层中的αN分解成了α相和CrN,造成基体贫Cr,降低了基材的耐蚀性能.马氏体不锈钢低温离子渗氮处理不仅可以提高表面硬度,而且可以获得良好的耐蚀性能.     

3Cr13钢450℃不同气氛等离子体渗氮层表征

对3Cr13钢在450 ℃氨气和氨氮混合气氛中分别渗氮4、8和12 h后的渗氮层进行了对比。利用光学显微镜、显微硬度计、X射线衍射仪、电化学工作站对渗氮层截面显微组织、显微硬度、相组成以及耐蚀性进行了表征。氨气渗氮层由化合物层和白亮层组成,而氨气和氮气混合气氛渗氮层中没有出现白亮层。氨气渗氮12 h后,渗氮层的表面硬度为1050.0 HV0.05;表面化合物层主要相为ε-Fe_2-3N,次要相为γ′-Fe₄N,出现了少量的CrN,白亮层相组成为γ′-Fe₄N;渗氮后极化曲线钝化区变宽,自腐蚀电流密度减小,耐蚀性提高。氨氮混合气氛渗氮12 h后,渗层的表面硬度为998.0 HV0.05;气氛中N浓度升高,渗氮8 h后CrN含量增加,次要相由氨气渗氮8 h的γ′-Fe₄N变为CrN;随着渗氮时间延长至12 h,渗层的自腐蚀电流密度降低,钝化区略有变宽,耐蚀性略有提高。     

00Cr12Ni9Mo4Cu2Ti马氏体时效不锈钢离子渗氮组织和性能

对00Cr12Ni9Mo4Cu2Ti马氏体时效不锈钢进行了离子渗氮处理,研究了不同渗氮条件下所形成的渗氮层的相结构与性能。结果表明:经离子渗氮后的00Cr12Ni9Mo4Cu2Ti马氏体时效不锈钢的表面硬度、耐磨性都有明显的提高,表面硬度最高达到了1350HV0.05。当样品在400℃渗氮时,表层新相主要由α相组成;当渗氮温度上升至500℃时,表层新相主要由αN相、γ′-Fe4N相、ε相组成,并有大量的CrN相形成;当渗氮温度高于600℃时,ε相、CrN的含量继续增加,γ′-Fe4N相逐渐减少,αN相几乎完全分解。伴随着CrN相的生成,样品的耐磨性得到了提高,表面耐腐蚀性能有一定下降。实验还观察到该马氏体时效不锈钢渗氮层中有微裂纹产生,裂纹的形成与样品的残余内应力和氮化物相生成有关。     

2Cr13马氏体不锈钢活性屏离子渗氮技术

对2Cr13马氏体不锈钢分别进行常规直流离子渗氮和活性屏离子渗氮对比试验。渗氮温度均为440℃,渗氮时间为8 h。采用金相显微镜、扫描电镜、X射线衍射仪、表面粗糙度仪、显微硬度仪和电化学工作站等设备分析表征两种渗氮样品。实验结果表明:活性屏离子渗氮在避免了传统离子渗氮缺点的同时,取得了与其相同的硬化效果。可在马氏体不锈钢表面制备一定厚度的均匀致密的白亮层,其相结构是以ε-Fe_(2-3)N相为主,并伴随少量的αN相。马氏体不锈钢活性屏渗氮处理不仅可以提高表面硬度,而且获得了良好的耐蚀性能。     

电弧等离子体辅助渗氮处理Cr12MoV钢的组织结构及硬度

采用不同温度对Crl2MoV钢进行电弧等离子体辅助渗氮处理.采用X射线衍射(XRD)分析渗氮层的相组成,采用扫描电子显微镜(SEM)及光学显微镜分别观察渗氮样品表面形貌及横截面形貌,利用显微硬度计测试渗氮层的硬度分布.结果表明:实验钢渗氮层的结构由CrN+γ'-Fe4N+ε-Fe3N的化合物层及由含氮马氏体相α-Fe (N)组成,渗氮层的厚度随处理温度的升高而增加.渗氮处理后能明显提高Cr12MoV钢基体的显微硬度.     

离子渗氮温度对Fe-C-Cr-Ni-Mn-V沉淀硬化型奥氏体不锈钢渗层组织和性能的影响

采用离子渗氮工艺对一种Fe-C-Cr-Ni-Mn-V沉淀硬化型奥氏体不锈钢进行表面改性处理。利用光学显微镜(OM)、X射线衍射(XRD)、电子探针显微分析仪(EPMA)和维氏硬度计对不同离子渗氮温度下渗层的组织和性能进行了研究。结果表明,Fe-C-Cr-Ni-Mn-V沉淀硬化型奥氏体不锈钢经430~520 ℃离子渗氮处理10 h后,试样表面均形成一层厚度均匀的渗氮层,表面硬度显著增大。随着离子渗氮温度的升高,渗层厚度增大,520 ℃渗氮时渗层厚度达到78 μm。当渗氮温度为430 ℃时,渗层表面主要由γ_N+CrN+γ′-Fe₄N相组成;当渗氮温度升高至520 ℃时,渗层表面主要由γ′-Fe₄N+CrN+ε-Fe_2-3N相组成。在3种渗氮温度下,渗层中均有CrN析出,导致渗层耐蚀性低于基体组织。     

工件电位对奥氏体不锈钢活性屏离子渗氮的影响

用活性屏离子渗氮技术分别对处于悬浮电位和阳极电位的AISI 316L奥氏体不锈钢进行低温渗氮处理.并对渗氮层的组织、形貌、相结构、显微硬度和耐蚀性能进行分析.结果表明,在这两种电位状态下处理的试样均可获得具有S相结构特征的单相硬化层.渗氮层不仅具有高的硬度,还有良好的耐蚀性能.在活性屏离子渗氮过程中,从活性屏上溅射下来的中性S相粒子也可以起到氮载体的作用.活性屏空间中性粒子和电子的撞击足以消除不锈钢表面钝化膜对氮的阻隔作用.     

活性屏与工件的距离对40Cr钢活性屏离子渗氮行为的影响

为提高40Cr钢的抗磨及耐蚀性能,用304不锈钢冲孔板制成的活性屏对40Cr钢进行离子渗氮(ASPN)处理,研究了活性屏与工件的距离对渗层组织结构和性能的影响,并与普通直流离子渗氮(DCPN)进行了比较。用光学显微镜(OM)、X射线衍射仪(XRD)、辉光放电光谱仪(GDOES)、显微硬度计、往复摩擦磨损试验机和电化学工作站对渗层组织、相成分、硬度、耐磨及耐腐蚀性能进行分析。结果表明:经不锈钢活性屏离子渗氮处理后,试样表面得到了致密均匀的渗氮层,渗层主要由ε-Fe2-3N、γ′-Fe4N和CrN相组成,且随着试样与活性屏距离从10mm、20mm增加到30mm,对应的渗层厚度从6μm、4.7μm减小到3.5μm。经氮化处理后,40Cr钢的耐磨性和耐腐蚀性都有显著的提高,ASPN处理后试样的耐腐蚀性较DCPN有明显的提高。     

渗扩时间比对AISI 316不锈钢渗氮层组织与性能的影响

采用真空两段渗氮工艺,在不同的强渗、扩散时间下对AISI 316不锈钢进行渗氮处理,通过X射线衍射(XRD)、扫描电镜(SEM)、光学显微镜(OM)、显微硬度测试和摩擦磨损试验等分析了渗氮层的组织和性能。结果表明,经过12 h的真空渗氮后,AISI 316不锈钢表面形成了一层由γ′-Fe₄N、ε-Fe_2-3N和CrN等相组成的渗氮层,其表面硬度和耐磨性能相较于基体均有明显的提高。其中,渗扩时间比为1∶1(强渗6 h、扩散6 h)时的渗层厚度约为96 μm,表面硬度约为1069 HV0.5,是基体表面硬度的4.5倍,在20 N载荷下的磨损量约为基体的1/3;渗扩时间比为1∶2(强渗4 h、扩散8 h)时的渗层厚度约为120 μm,ε-Fe_2-3N相衍射峰增强,在20 N载荷下的磨损量约为基体的1/30。延长扩散时间能增加渗氮层厚度,改善表面形貌,进一步提高不锈钢的耐磨性。     

马氏体不锈钢不同渗氮方法对比试验

采用离子渗氮、液体渗氮及气体渗氮对耐蚀耐热马氏体型热稳定不锈钢1Cr12Ni2WMoVNb进行表面改性,研究了不同渗氮方法下不锈钢的硬度、组织形貌、物相变化及脆性,并对3种渗氮方法下不锈钢的耐蚀性及耐高温磨损性能进行了比较。结果表明:3种渗氮方法均可大幅度提高不锈钢的表面硬度,且不同渗氮处理后不锈钢的渗层组织结构大致相同,但表面物相有所差异,离子渗氮后的表面物相主要为Fe₄N及少量CrN相,液体渗氮后为Fe₃O₄及ε相,气体渗氮后为Fe₃O₄、Fe₄N及少量ε相;3种渗氮方法均可提高不锈钢的耐磨损性能,特别是在500~600 ℃下的高温耐磨性得到了大幅提升,但不锈钢渗氮后的耐蚀性均有所降低。     

Effects of Post-weld Heat Treatment on Microstructure,Mechanical Properties and the Role of Weld Reinforcement in 2219 Aluminum Alloy TIG-Welded Joints

In as-welded state, each region of 2219 aluminum alloy TIG-welded joint shows diff erent microstructure and microhardness due to the diff erent welding heat cycles and the resulting evolution of second phases. After the post-weld heat treatment, both the amount and the size of the eutectic structure or θ phases decreased. Correspondingly, both the Cu content in α-Al matrix and the microhardness increased to a similar level in each region of the joint, and the tensile strength of the entire joint was greatly improved. Post-weld heat treatment played the role of solid solution strengthening and aging strengthening. After the post-weld heat treatment, the weld performance became similar to other regions, but weld reinforcements lost their reinforcing eff ect on the weld and their existence was more of an adverse eff ect. The joint without weld reinforcements after the post-weld heat treatment had the optimal tensile properties, and the specimens randomly crack in the weld zone.     

The First Phase of the SRIF Industrialized Base in ＂West Area＂ Has Been Put into Operation

After nearly two years＇ tense construction, the first phase of industrialized base of Shenyang Research Institute of Foundry （SRIF）, located at the Tiexi Casting and Forging Industrial Park in the west of Tiexi District, has now been completed and formally put into operation.     

Effect of Rare Earth Doping on Impedance,Modulus and Conductivity Properties of Multiferroic Composites:0.5(BiLa_xFe_(1-x)O_3)–0.5(PbTiO_3)

The Lanthanum-doped bismuth ferrite–lead titanate compositions of 0.5(Bi LaxFe1-xO3)–0.5(Pb Ti O3)(x = 0.05,0.10,0.15,0.20)(BLxF1-x-PT) were prepared by mixed oxide method.Structural characterization was performed by X-ray diffraction and shows a tetragonal structure at room temperature.The lattice parameter c/a ratio decreases with increasing of La(x = 0.05–0.20) concentration of the composites.The effect of charge carrier/ion hopping mechanism,conductivity,relaxation process and impedance parameters was studied using an impedance analyzer in a wide frequency range(102–106Hz) at different temperatures.The nature of Nyquist plot confirms the presence of bulk effects only,and non-Debye type of relaxation processes occurs in the composites.The electrical modulus exhibits an important role of the hopping mechanism in the electrical transport process of the materials.The ac conductivity and dc conductivity of the materials were studied,and the activation energy found to be 0.81,0.77,0.76 and 0.74 e V for all compositions of x = 0.05–0.20 at different temperatures(200–300 °C).     

Quantitative Analysis of the Crystallographic Orientation Relationship Between the Martensite and Austenite in Quenching–Partitioning–Tempering Steels

The orientation relationships(ORs)between the martensite and the retained austenite in low-and medium-carbon steels after quenching–partitioning–tempering process were studied in this work.The ORs in the studied steels are identified by selected-area electron diffraction(SAED)as either K–S or N–W ORs.Meanwhile,the ORs were also studied based on numerical fitting of electron backscatter diffraction data method suggested by Miyamoto.The simulated K–S and N–W ORs in the low-index directions generally do not well coincide with the experimental pole figure,which may be attributed to both the orientation spread from the ideal variant orientations and high symmetry of the low-index directions.However,the simulated results coincide well with experimental pole figures in the high-index directions{123}_(bcc).A modified method with simplicity based on Miyamoto’s work was proposed.The results indicate that the ORs determined by modified method are similar to those determined by Miyamoto’method,that is,the OR is near K–S OR for the low-carbon Q–P–T steel,and with the increase of carbon content,the OR is closer to N–W OR in medium-carbon Q–P–T steel.     

The Mirror with Patterns of Auspicious Animals and Grapes——Exquisite cast mirror and the technology of surface tin-enrichment by rubbing-in and infiltration of tin-rich powder

<正>Bronze mirrors were used by the Chinese people before the introduction of the glass mirror.Only after it was replaced by the glass mirror did the bronze mirror gradually retreat from people's lives.Different styles of bronze mirrors were made in different historical periods,particularly in the Warring States Period,the Han and Tang Dynasties,which were the three peaks of the development of bronze mirror arts in ancient China.The casting techniques were exquisite.The surface of the bronze mirror was smooth and bright enough to reflect one's image,and there were scarcely any casting defects on the mirror surface.On the back of the bronze mirror,there were rich depictions of Arts and Humanities,and the ornamentations were also     

The 9th China International Diecasting Congress & Exhibition

The 9th China International Diecasting Congress ＆ Exhibition was held on July 22-24, 2014 at Shanghai New International Expc Centre. This exhibition was the most successful over the years, with over 6890 visitors and 155 exhibitors, and the exhibition area increased by 30% from 9,500 square meters in 2012 to 12340 square meters. Die casting enterprises from a total of 24 countries and regions, including China mainland, Chinese Taiwan and Hong Kong, South Korea, Japan, Germany, India, Thailand, Malaysia, the United States, Russia, Australia, Iran, Ukraine, Brazil, Colombia, Singapore, Austria, Canada, Croatia, France, Turkey, United Kingdom, Vietnam, attended the congress and exhibition.     

Introduction of the Fluid Control Engineering Institute of Kunming University of Science and Technology

正The Fluid Control Engineering Institute of Kunming University of Science and Technology was set up in 1996.The researches of institute concentrate on electro-hydraulic(pneumatic)servo/proportional control and hydromechatronics.The Institute is committed to research and development of electro-hydraulic control of high-end technical equipment in ferrous metallurgy refining produc-     

RARE METALS Volume Contents

正~~     

Antimony Induced Crystallization of Amorphous Silicon

Antimony induced crystallization of PVD (physics vapor deposition) amorphous silicon can be observed on sapphire substrates. Very large crystalline regions up to several tens of micrometers can be formed. The Si diffraction patterns of the area of crystallization can be observed with TEM (transmission electron microscopy). Only a few and much smaller crystals of the order of 1μm were formed when the antimony layer was deposited by MBE (molecular beam epitaxy) compared with a layer formed by thermal evaporation. The use of high vacuum is essential in order to observe any Sb induced crystallization at all. In addition it is necessary to take measures to limit the evaporation of the antimony.     

A CUMULATIVE FATIGUE DAMAGE RULE UNDER THE ALTERNATIVE OF CORROSION OR CYCLIC LOADING

Fatigue damage increases with the applied loading cycles in a cumulative manner and the material deteriorates with the corrosion time. A cumulative fatigue damage rule under the alternative of corrosion or cyclic loading was proposed. The specimens of aluminum alloy LY12-CZ soaked in corrosive liquid for different times were tested under the constant amplitude cyclic loading to obtain S-N curves. The test was carried out to verify the proposed cumulative fatigue damage rule under the different combinations among corrosion time, loading level, and the cycle numbers. It was shown that the predicted residual fatigue lives showed a good agreement with the experimental results and the proposed rule was simple and can be easily adopted.