The Cu(I)- and HNO<Subscript>3</Subscript>-catalyzed oxidation of substituted toluenes to the benzoic acid based on NO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> recycling

Based on the recycling of NO _x , the Cu(I)- and HNO₃-catalyzed oxidation of 2-chloro-4-(methylsulfonyl)toluene to 2-chloro-4-(methylsulfonyl)benzoic acid has been developed with an excellent yield of 84.2% and a purity of 99.7%. The optimized reaction conditions (160 °C, oxygen pressure 1.5 MPa, HNO₃ concentration 25 wt%, HNO₃: substrate 0.5:1) use 1.0 mol% CuI as catalyst. The dosage of HNO₃ in the new process is only 25% of the stoichiometric amount and 12.5% of the amount of the traditional process. The NO _x emission is 5% amount of the traditional process. The oxidation of several additional toluene derivatives with comparable yields demonstrates the generality to these reaction conditions.     

Synthesis,structure, and electric properties of oxygen-deficient perovskites Ba<Subscript>3</Subscript>In<Subscript>2</Subscript>ZrO<Subscript>8</Subscript> and Ba<Subscript>4</Subscript>In<Subscript>2</Subscript>Zr<Subscript>2</Subscript>O<Subscript>11</Subscript>

Perovskite phases Ba₃In₂ZrO₈ and Ba₄In₂Zr₂O₁₁ with the nominal concentration of structural oxygen vacancies 1/9 and 1/12, respectively, were synthesized by solid-phase and solution methods. X-ray diffraction showed cubic symmetry of both phases with the unit cell parameter a = 0.4193(2) and 0.4204(3) nm, respectively. The absence of superstructural lines resulted in the conclusion on statistical arrangement of oxygen vacancies. Thermogravimetry and mass spectrometry proved that both phases can reversibly absorb water from gas phase (pH₂O = 2 × 10⁻² atm) with observed correlation between the concentration of oxygen vacancies and amount of absorbed water. The total water amount was up to 0.9 mol per formula unit or, if recalculated for perovskite unit ABO₃, 0.3 and 0.23 mol H₂O, respectively. The temperature curves of coductivity in the atmosphere with various partial water vapor pressures (pH₂O = 3 × 10⁻⁵ and 2 × 10⁻² atm) showed significantly higher conductivity and lower activation energy (0.52 eV) in humid atmosphere due to proton transfer. The proton conductivity is up to 5 × 10⁻⁴ Ohm⁻¹ cm⁻¹ at 300°C for Ba₃In₂ZrO₈ specimen. IR spectrometry showed that protons in the structure exist primarily in OH-groups.     

Hydrolysis of cellulose by the heteropoly acid H<Subscript>3</Subscript>PW<Subscript>12</Subscript>O<Subscript>40</Subscript>

The potential of heteropoly acid H₃PW₁₂O₄₀ to catalyze the hydrolysis of cellulose to glucose under hydrothermal conditions was explored. This technology could contribute to sustainable societies in the future by using cellulose biomass. A study to optimize the reaction conditions, such as the amount of catalyst, reaction time, temperature, and the amount of cellulose used, was performed. A remarkably high yield of glucose (50.5%) and selectivity higher than 90% at 453 K for 2 h with a mass ratio of cellulose to H₃PW₁₂O₄₀ of 0.42 were achieved. This was attributed to the high hydrothermal stability and the excellent catalytic properties, such as the strong Brønsted acid sites. This homogeneous catalyst can be recycled for reuse by extraction with diethyl ether. The results illustrate that H₃PW₁₂O₄₀ is an environmentally benign acid catalyst for the hydrolysis of cellulose.     

Investigation into the formation of heteronuclear clusters of formula [{Ru<Subscript>6</Subscript>C(CO)<Subscript>16</Subscript>Ag<Subscript>2</Subscript>X}<Subscript>2</Subscript>]<Superscript>2−</Superscript> (X = Cl,Br or I)

Reaction of [Ru₆C(CO)₁₆]²⁻ with an excess of AgX (X = Cl, Br or I) affords heteronuclear clusters of formula [{Ru₆C(CO)₁₆Ag₂X}₂]²⁻ in 80% yield, which for X = I and X = Br/Cl were crystallographically characterised. The formation of the cluster was followed in solution using electrospray ionisation mass spectrometry (ESI-MS), which revealed the presence of a wide range of clusters with the general formula [{Ru₆C(CO)₁₆} _x Ag _y X _z ]^{(2x−y+z)−} where x = 1 or 2, y = 1, 2, 3 or 4 and z = 0, 1 or 2. The high yield of the product despite the evident complicated solution speciation is attributed to selective crystallisation of the observed compound driving the equilibrium toward this product.     

Synthesis and characterization of the [Ru<Subscript>3</Subscript>O(CH<Subscript>3</Subscript>COO)<Subscript>6</Subscript>(py)<Subscript>2</Subscript>(BPE)Ru(bpy)<Subscript>2</Subscript>Cl](PF<Subscript>6</Subscript>)<Subscript>2</Subscript> dimer

The polymetallic [Ru₃O(CH₃COO)₆(py)₂(BPE)Ru(bpy)₂Cl](PF₆)₂ complex (bpy = 2,2′-bipyridine, BPE = trans-1,2-bis(4-pyridil)ethylene and py = pyridine) was assembled by the combination of an electroactive [Ru₃O] moiety with a [Ru(bpy)₂(BPE)Cl] photoactive centre, and its structure was determined using positive ion electrospray (ESI-MS) and tandem mass (ESI-MS/MS) spectrometry. The [Ru₃O(CH₃COO)₆(py)₂(BPE)Ru(bpy)₂Cl]²⁺ doubly charged ion of m/z 732 was mass-selected and subject to 15 eV collision-induced dissociation, leading to a specific dissociation pattern, diagnostic of the complex structure. The electronic spectra display broad bands at 409, 491 and 692 nm ascribed to the [Ru(bpy)₂(BPE)] charge-transfer bands and to the [Ru₃O] internal cluster transitions. The cyclic voltammetry shows five reversible waves at −1.07 V, 0.13 V, 1.17 V, 2.91 V and −1.29 V (vs SHE) assigned to the [Ru₃O]^{−1/0/+1/+2/+3} and to the bpy^0/−1 redox processes; also a wave is observed at 0.96 V, assigned to the Ru^+2/+3 pair. Despite the conjugated BPE bridge, the electrochemical and spectroelectrochemical results indicate only a weak coupling through the π-system, and preliminary photophysical essays showed the compound decomposes under visible light irradiation.     

Synthesis of nonequilibrium Ir<Subscript>x</Subscript>Re<Subscript>1-x</Subscript> solid solutions. Crystal structure of [Ir(NH<Subscript>3</Subscript>)<Subscript>5</Subscript>Cl]<Subscript>2</Subscript>[ReCl<Subscript>6</Subscript>]Cl<Subscript>2</Subscript>

Synthesis of five binary complex salts with an [Ir(NH₃)₅Cl]²⁺ complex cation is described. The counterions are [ReCl₆]^2–, [IrCl₆]^2–, [ReBr₆]^2–, and Cl^–. A polycrystal X-ray diffraction study has been performed for [Ir(NH₃)₅Cl]₂[ReCl₆]Cl₂, and its crystal structure has been determined. A series of Ir _x Re_1–x phases (0.5 x > 1) were obtained by reductive thermolysis. For the Ir-Re system, the history of the V/Z(x) dependence has been refined.Original Russian Text Copyright © 2004 by S. A. Gromilov, S. V. Korenev, I. V. Korolkov, K. V. Yusenko, and I. A. BaidinaTranslated from Zhurnal Strukturnoi Khimii, Vol. 45, No. 3, pp. 508–515, May–June 2004.     

Ionic dissociations of chlorosulfonic acid in microsolvated clusters: A density functional theory and ab initio MO study

Ionic dissociation of chlorosulfonic acid (HSO₃Cl) in the molecular clusters HSO₃Cl-(H₂O) _n (n = 1–4) and HSO₃Cl-NH₃-(H₂O) _n (n = 0–3) was investigated by density functional theory and ab initio molecular orbital theory. The equilibrium structures, binding energies, and thermodynamic properties, such as relative enthalpy and relative Gibbs free energy, and were calculated using the hybrid density functional (B3LYP) method and the second order M?ller-Plesset approximation (MP2) method with the 6-311++G** basis set. Chlorosulfonic acid was found to require a minimum of three water molecules for ionization to occur and at least one water molecule to protonate ammonia. The corresponding clusters with fewer water molecules were found to be strongly hydrogen-bonded. The related properties and acid strength of chlorosulfonic acid were discussed and compared to the acid strengths of perchloric acid and sulfuric acid in the context of clusters with ammonia and water. The relative stabilities of these clusters were also investigated. Supported by the National Natural Science Foundation of China (Grant No. 20273046), the Camille and Henry Dreyfus Foundation (Award No. TH-00-028) of California State University, Fullerton, and the Younger Teacher Foundation of Suzhou University (Grant No. Q31094040)     

Phase transition of RbH<Subscript>2</Subscript>PO<Subscript>4</Subscript> and its composite with SiO<Subscript>2</Subscript> studied by thermal analysis

The phase transition at T _p (~109 °C) of RbH₂PO₄ and its composite with SiO₂ has been investigated by thermal analysis here. In the case of neat RbH₂PO₄, there is a linear relationship between endothermic peak temperature (T _m) and square root of heating rate (Φ ^1/2), from which the onset temperature of phase transition can be determined. Besides, Kissinger method and another calculation method were employed to obtain the activation energy of phase transition. The detailed deduction process was presented in this paper, and the estimated activation energies are E ₁ ≈ 126.3 kJ/mol and E ₂ ≈ 129.2 kJ/mol, respectively. On the other hand, the heterogeneous doping of RbH₂PO₄ with SiO₂ as dopant facilitates its proton conduction and leads to the disappearance of jump in conductivity at T _p. The heats of transition in the composites decrease gradually with increasing the molar fraction of SiO₂ additives. In the cooling process, a new and broad exothermic peak appeared between ~95 and ~110 °C, and its intensity also changes with the SiO₂ amount. These phenomena might be related to the formation of amorphous phase of RbH₂PO₄ on the surface of SiO₂ particles due to the strong interface interaction.     

XAFS investigation of [Pd(NH<Subscript>3</Subscript>)<Subscript>4</Subscript>][AuCl<Subscript>4</Subscript>]<Subscript>2</Subscript> and its thermolysis products

Thermolysis of double complex salt [Pd(NH₃)₄][AuCl₄]₂ has been studied in helium atmosphere from ambient to 350 °C. The XAFS of Pd K and Au L₃ edges and thermogravimetry measurements have been carried out to characterize the intermediates and the final product. In the temperature range 115–160 °C the complex is decomposed to form Pd(NH₃)₂Cl₂ and AuCl_4−x N _x species with x ranging from 2 to 3. Subsequent heating of the intermediate up to 300 °C leads to the total loss of NH₃. The Au–Cl and Au–Au bonds form the local environment of Au at the stage of decomposition while only four chlorine atoms are around Pd. At the temperature of 330 °C the Au and Pd nanoparticles as well as residues of palladium chloride are detected. The final product consists of separated Au and Pd nanoparticles.     

Benzyl alcohol-based synthesis of mono- and bis-dihydropyridines in the presence of Al(HSO<Subscript>4</Subscript>)<Subscript>3</Subscript>, sodium nitrite,and sodium bromide under solvent-free conditions

Dihydropyridines were synthesized in good to excellent yields in the presence of NaNO₂, Al(HSO₄)₃, and a catalytic amount of NaBr at room temperature. Low cost, the use of available reagents, simple methodology, and easy work-up procedure make this method attractive for organic synthesis.     

Preparation of Pd(PPh<Subscript>2</Subscript>H)<Subscript>2</Subscript>(PPh<Subscript>3</Subscript>)<Subscript>2</Subscript> and its Role as a Precursor of a Dinuclear Complex with Bridging Phosphide Ligands

Reaction of PPh₂H with Pd(PPh₃)₄ in a 4:1 molar ratio produced the Pd complex with two diphenylphosphine ligands, Pd(PPh₂H)₂(PPh₃)₂ (1). Complex (1) was characterized by n.m.r. (¹H and ³¹P{¹H}) spectra as well as by elemental analysis. Reaction of (1) with RhCl(PPh₃)₃ yielded a Pd–Rh heterobimetallic complex with bridging phosphide ligands, formulated as [(Ph₃P)₂Pd(μ-PPh₂)₂Rh(PPh₃)₂]Cl (2).     

Radical–molecule reaction CH<Subscript>2</Subscript>Cl + NO<Subscript>2</Subscript>: a mechanistic study

The radical–molecule reaction mechanism of CH₂Cl with NO₂ has been explored theoretically at the B3LYP/6–311G(d,p) and MC–QCISD (single-point) levels of theory. Our results indicate that the title reaction proceeds mostly through singlet pathways, less go through triplet pathways. The initial association between CH₂Cl and NO₂ is found to be the carbon-to-nitrogen attack forming the adduct a H₂ClCNO₂ with no barrier, followed by isomerization to b ₁ H₂ClCONO-trans which can easily convert to b ₂ H₂ClCONO-cis. Subsequently, the most feasible pathway is the C–Cl and O–N bonds cleavage along with the N–Cl bond formation of b (b ₁ , b ₂ ) leading to product P ₁ CH₂O + ClNO, which can further dissociate to give P ₅ CH₂O + Cl + NO. The second competitive pathway is the 1,3-H-shift associated with O–N bond rupture of b ₁ to form P ₂ CHClO + HNO. Because the intermediates and transition states involved in the above two favorable channels all lie below the reactants, the CH₂Cl+NO₂ reaction is expected to be rapid, as is confirmed by experiment. The present results can lead us to understand deeply the mechanism of the title reaction and may be helpful for further experimental investigation of the reaction.     

Electrochemical lithium insertion in β-MoO<Subscript>3</Subscript>: novel Li<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>MoO<Subscript>3</Subscript> bronzes

New lithium molybdenum bronzes have been synthesized by electrochemical lithium insertion. Through electrochemical spectroscopy techniques we have detected that lithium insertion proceeds at least in a two-step reduction process. The maximum amount of lithium inserted in β-MoO₃ leads to a high specific capacity of the cell of 370 Ah kg^–1. However, this capacity was lost after the first charge-discharge cycle, resulting in a total loss of 25%, due to structural transformations. The structural study of the insertion process showed that each step of the process can be associated with the formation of different single phases of variable composition, Li _x MoO₃. Electronic Publication     

Catalytic Properties of TiO<Subscript>2</Subscript>/Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> Nanoparticles in Plasma Chemical Treatment

We proposed here a new process coupling dielectric barrier discharge (DBD) plasma with magnetic photocatalytic material nanoparticles for improving yield in DBD degradation of methyl orange (MO). TiO₂ doped Fe₃O₄ (TiO₂/Fe₃O₄) was prepared by the sol-gel method and used as a new type of magnetic photocatalyst in DBD system. It was found that the introduction of TiO₂/Fe₃O₄ in DBD system could effectively make use of the energy generated in DBD process and improve hydroxyl radical contributed by the main surface Fenton reaction, photocatalytic reaction and catalytic decomposition of dissolved ozone. Most part of MO (88%) was degraded during 30 min at peak voltage of 13 kV and TiO₂/Fe₃O₄ load of 100 mg/L, with a rate constant of 0.0731 min^?1 and a degradation yield of 7.23 g/(kW h). The coupled system showed higher degradation efficiency for MO removal.     

Electrophilic addition to norbornene derivatives containing CF<Subscript>3</Subscript> and NO<Subscript>2</Subscript> groups

Electrophilic sulfenylation, selenenation, and halogenation of bicyclo[2.2.1]heptenes containing CF₃ or NO₂ group in position endo-5 were studied. The sulfenylation and selenenation were accomplished by arylsulfene- and arylselenenamides activated by POHal₃ (Hal = Br, Cl), and iodination was performed by KICl₂. The reactions are regiospecific and involve an exo-attack of the electrophilic fragment (arylthio or arylseleno group or iodine) on the C=C bond atom located closer to the CF₃ or NO₂ group. Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1445–1448, June, 2005.     

Antiferromagnetic coupling in [Mn<Subscript>12</Subscript>O<Subscript>12</Subscript>(O<Subscript>2</Subscript>CMe)<Subscript>6</Subscript>(<Emphasis Type="Italic">p</Emphasis>-CO<Subscript>2</Subscript>-phenyl nitronyl

The synthesis of [Mn₁₂O₁₂(O₂CMe)₆(p-CO₂-phenyl nitronyl nitroxide)₁₀(H₂O)₄]· 4H₂O, (1), by direct replacement of some of the acetate groups in [Mn₁₂O₁₂(O₂CMe)₁₆(H₂O)₄] · 4H₂O · 2MeCO₂H, (2), with the organic radical p-HO₂C-phenyl nitronyl nitroxide, (3), is reported. E.p.r. spectra show exchange narrowing in (1) due to coupling between the manganese ions and radicals. The isotropic hyperfine splitting constant from the manganese ions is a = 96 Oe at 5.5K. The magnetic susceptibility indicates antiferromagnetic exchange interactions between the manganese ions and the radicals with the Weiss constant = -25 K. The spin was determined to be S = 6 from magnetization data in the 2--30 K temperature range at 50 kOe, suggesting a mixture of ground state with excited states.     

Ethanol Production from H<Subscript>2</Subscript>SO<Subscript>3</Subscript>-Steam-Pretreated Fresh Sweet Sorghum Stem by Simultaneous Saccharification and Fermentation

The present work presents an alternative approach to ethanol production from sweet sorghum: without detoxification, acid-impregnated fresh sweet sorghum stem which contains soluble (glucose and sucrose) and insoluble carbohydrates (cellulose and hemicellulose) was steam pretreated under mild temperature of 100 °C. Simultaneous saccharification and fermentation experiments were performed on the pretreated slurries using Saccharomyces cerevisiae. Experimentally, ground fresh sweet sorghum stem was combined with H₂SO₃ at dosages of 0.25, 0.50, and 0.75 g/g dry matter (DM) and steam pretreated by varying the residence time (60, 120, or 240 min). According to enzymatic hydrolysis results and ethanol yields, H₂SO₃ was a powerful and mild acid for improving enzymatic digestibility of sorghum stem. At a solid loading of 10% (w/v) and acid dosage of 0.25 g/g DM H₂SO₃ at 100 °C for 120 min, 44.5 g/L ethanol was obtained after 48 ± 4 h of simultaneous saccharification and fermentation. This corresponded to an overall ethanol yield of 110% of the theoretical one, based on the soluble carbohydrates in the fresh sweet sorghum stem. The concentrations of hydroxymethylfurfural and furfural of the sulfurous acid pretreated samples were below 0.4 g/L. Ethanol would not inhibit the cellulase activity, at least under the concentration of 34 g/L.     

Synthesis and crystallization kinetics of the novel ion exchanger Na<Subscript>4</Subscript>Ti<Subscript>4</Subscript>Si<Subscript>3</Subscript>O<Subscript>10</Subscript> for cesium removal

Thermodynamics and crystallization kinetics of the hydrothermal synthesis of Na₄Ti₄Si₃O₁₀ (NaTS) were systemically studied by both experiments and model simulation. Experimental results showed that the curve of crystallinity with time was a characteristic signmoid in the shape that indicated the crystallization of Na₄Ti₄Si₃O₁₀ was a typical spontaneous nucleation process on the laboratory scale. Crystallization of NaTS belongs to the liquid-liquid transformation mechanism and the reaction is endothermic (ΔH = 15.3 kJ/mol). A mathematic model of crystallization kinetics was developed to simulate the synthesis of NaTS. Runge-Kutta and simplex methods were adopted to solve the partial differential equations. Model results fitted well with the experimental data and showed that the synthesis process belongs to spontaneous nucleation and crystal growth. Moreover, the very small crystal growth constant (5.6·10⁻⁷) and gel dissolution constant (7.0·10⁻⁷) indicate they are the rate-limiting steps of the whole synthesis process.     

The effects of sintering temperature and time on the structure and electrochemical performance of LiNi<Subscript>0.8</Subscript>Co<Subscript>0.2</Subscript>O<Subscript>2</Subscript> cathode materials derived from sol-gel method

LiNi _0.8Co _0.2O ₂ cathode materials were synthesized by the sol-gel method using citric acid as a chelating agent. The effects of sintering temperature and time on the structure and electrochemical performance of the materials were investigated. The materials were characterized by X-ray diffraction, together with refinement analysis by the Rietveld method. The results showed that sintering temperature and time had significant influence on the structure of the materials. The lattice parameters ( a, c, c/ a and volume) and the amount of Ni in the Li 3a site showed a peak shape change with sintering temperature and time. The sample sintering at 998 K for 24 h showed the best ordering layered structure with the maximum c/ a ratio and the least amount of Ni on the Li 3a site. The charge-discharge experiments also indicated that the sample had the best electrochemical properties, with an initial capacity of 181 mA h/g and a capacity retention of 82.9% after 50 cycles at a 0.1 C rate between 3.0 V and 4.2 V. In addition, the compositional homogeneity of these cathode materials derived using the sol-gel method was demonstrated by scanning electron microscopy/energy dispersive analysis.     

Synthesis of dimethyl ether from CO and H<Subscript>2</Subscript>

Thermodynamic conditions for synthesizing dimethyl ether from synthesis gas are determined. The optimum conditions of the process are as follow: T ∼ 300°C at p = 3 MPa for two catalysts loaded into the reactor: methanol synthesis catalyst (Katalco-58) and catalyst of methanol dehydration to dimethyl ether (γ-Al₂O₃). The changes that occur with the catalysts during this process are demonstrated by electron scanning microscopy.