ECR plasma etching of chemically vapour deposited diamond thin films

Arc jet deposited films of diamond have been patterned using Au or photoresist masks and electron cyclotron resonance (ECR) O/sub 2/ discharges. To achieve anisotropic features, additional RF-induced DC biasing of the sample is necessary. Diamond etch rates of 2000 AA/min were obtained for 1 mtorr, 400 W O/sub 2/ discharges with -80 V DC bias. The etch rates increase with either pressure or microwave power as a result of a greater density of atomic oxygen in the plasma. Chlorine (BCl/sub 3/)-based did not product significant etching of the diamond, but SF/sub 6//O/sub 2/ mixtures had slightly faster rates than O/sub 2/ alone.<>     

Low-Temperature Materials and Thin Film Transistors for Flexible Electronics

This paper addresses the low-temperature deposition processes and electronic properties of silicon based thin film semiconductors and dielectrics to enable the fabrication of mechanically flexible electronic devices on plastic substrates. Device quality amorphous hydrogenated silicon (a-Si:H), nanocrystalline silicon (nc-Si), and amorphous silicon nitride (a-SiN/sub x/) films and thin film transistors (TFTs) were made using existing industrial plasma deposition equipment at the process temperatures as low as 75/spl deg/C and 120/spl deg/C. The a-Si:H TFTs fabricated at 120/spl deg/C demonstrate performance similar to their high-temperature counterparts, including the field effect mobility (/spl mu//sub FE/) of 0.8 cm/sup 2/V/sup -1/s/sup -1/, the threshold voltage (V/sub T/) of 4.5 V, and the subthreshold slope of 0.5 V/dec, and can be used in active matrix (AM) displays including organic light emitting diode (OLED) displays. The a-Si:H TFTs fabricated at 75/spl deg/C exhibit /spl mu//sub FE/ of 0.6 cm/sup 2/V/sup -1/s/sup -1/, and V/sub T/ of 4 V. It is shown that further improvement in TFT performance can be achieved by using n/sup +/ nc-Si contact layers and plasma treatments of the interface between the gate dielectric and the channel layer. The results demonstrate that with appropriate process optimization, the large area thin film Si technology suits well the fabrication of electronic devices on low-cost plastic substrates.     

An ultralow-loss and broadband micromachined RF inductor for RFIC input-matching applications

In this brief, we demonstrate that ultralow-loss and broadband inductors can be obtained by using the CMOS process compatible backside inductively coupled-plasma (ICP) deep-trench technology to selectively remove the silicon underneath the inductors. The results show that a 378.5% increase in maximum Q-factor (Q/sub max/) (from 10.7 at 4.7 GHz to 51.2 at 14.9 GHz), a 22.1% increase in self-resonant frequency (f/sub SR/) (from 16.5 to 20.15 GHz), a 16.3% increase (from 0.86 to 0.9999) in maximum available power gain (G/sub Amax/) at 5 GHz, and a 0.654-dB reduction (from 0.654 dB to 4.08/spl times/10/sup -4/ dB) in minimum noise figure (NF/sub min/) at 5 GHz were achieved for a 2-nH inductor after the backside ICP dry etching. In addition, state-of-the-art ultralow-loss G/sub Amax//spl les/0.99 (i.e., NF/sub min//spl les/0.045 dB) for frequencies lower than 12.5 GHz was achieved for this 2-nH inductor after the backside inductively coupled-plasma dry etching. This means this on-chip inductor-on-air can be used to realize an ultralow-noise 3.1-10.6 GHz ultrawide-band RFIC. These results show that the CMOS process compatible backside ICP etching technique is very promising for system-on-a-chip applications.     

High breakdown voltage AlAs/InGaAs quantum barrier varactor diodes

Data are presented on single quantum barrier AlAs/In/sub 0.53/Ga/sub 0.47/As varactor diodes intended as submillimetre wavelength frequency multipliers that exhibit extremely high breakdown voltage and excellent capacitance modulation characteristics. Record breakdown voltages as high as 12 V were achieved with a composite 50AA/50AA/50AA thick In/sub 0.52/Al/sub 0.48//AlAs/In/sub 0.52/Al/sub 0.48/As barrier sandwiched between 3000 AA(1.2*10/sup 17/ cm/sup -3/) In/sub 0.53/Ga/sub 0.47/As depletion regions.<>     

High-performance nonhydrogenated nickel-induced laterally crystallized P-channel poly-Si TFTs

High-performance nickel-induced laterally crystallized (NILC) p-channel poly-Si thin-film transistors (TFTs) have been fabricated without hydrogenation. Two different thickness of Ni seed layers are selected to make high-performance p-type TFTs. A very thin seed layer (e.g., 5 /spl Aring/) leads to marginally better performance in terms of transconductance (Gm) and threshold voltage (V/sub th/) than the case of a 60 /spl Aring/ Ni seed layer. However, the p-type poly-Si TFTs crystallized by the very thin Ni seeding result in more variation in both V/sub th/ and G/sub m/ from transistor to transistor. It is believed that differences in the number of laterally grown polycrystalline grains along the channel cause the variation seen between 5 /spl Aring/ NILC TFTs compared to 60-/spl Aring/ NILC TFTs. The 60 /spl Aring/ NILC nonhydrogenated TFTs show consistent high performance, i.e., typical electrical characteristics have a linear field-effect hole mobility of 156 cm/sup 2//V-S, subthreshold swing of 0.16 V/dec, V/sub th/ of -2.2 V, on-off ratio of >10/sup 8/, and off-current of <1/spl times/10/sup -14/ A//spl mu/m when V/sub d/ equals -0.1 V.     

4H-SiC power bipolar junction transistor with a very low specific ON-resistance of 2.9 m/spl Omega//spl middot/cm/sup 2/

This letter reports a newly achieved best result on the specific ON-resistance (R/sub SP/spl I.bar/ON/) of power 4H-SiC bipolar junction transistors (BJTs). A 4H-SiC BJT based on a 12-/spl mu/m drift layer shows a record-low specific-ON resistance of only 2.9 m/spl Omega//spl middot/cm/sup 2/, with an open-base collector-to-emitter blocking voltage (V/sub ceo/) of 757 V, and a current gain of 18.8. The active area of this 4H-SiC BJT is 0.61 mm/sup 2/, and it has a fully interdigitated design. This high-performance 4H-SiC BJT conducts up to 5.24 A at a forward voltage drop of V/sub CE/=2.5 V, corresponding to a low R/sub SP-ON/ of 2.9 m/spl Omega//spl middot/cm/sup 2/ up to J/sub c/=859 A/cm/sup 2/. This is the lowest specific ON-resistance ever reported for high-power 4H-SiC BJTs.     

A 4.15 kV 9.07-m/spl Omega//spl middot/cm/sup 2/ 4H-SiC Schottky-barrier diode using Mo contact annealed at high temperature

In this letter, we report the fabrication of high-voltage and low-loss 4H-SiC Schottky-barrier diodes (SBDs) with a performance close to the theoretical limit using a Mo contact annealed at high-temperature. High-temperature annealing for the Mo contact was found to be effective in controlling the Schottky-barrier height at 1.2-1.3 eV without degradation of n-factor and reverse characteristics. We successfully obtained a 1-mm/sup 2/ Mo-4H-SiC SBD with a breakdown voltage (V/sub b/) of 4.15 kV and a specific on resistance (R/sub on/) of 9.07 m/spl Omega//spl middot/cm/sup 2/, achieving a best V/sub b//sup 2//R/sub on/ value of 1898 MW/cm/sup 2/. We also obtained a 9-mm/sup 2/ Mo-4H-SiC SBD with V/sub b/ of 4.40 kV and R/sub on/ of 12.20 m/spl Omega//spl middot/cm/sup 2/.     

A high current gain 4H-SiC NPN power bipolar junction transistor

This work reports the development of high power 4H-SiC bipolar junction transistors (BJTs) by using reduced implantation dose for p+ base contact region and annealing in nitric oxide of base-to-emitter junction passivation oxide for 2 hours at 1150/spl deg/C. The transistor blocks larger than 480 V and conducts 2.1 A (J/sub c/=239 A/cm/sup 2/) at V/sub ce/=3.4 V, corresponding to a specific on-resistance (R/sub sp on/) of 14 m/spl Omega/cm/sup 2/, based on a drift layer design of 12 /spl mu/m doped to 6/spl times/10/sup 15/cm/sup -3/. Current gain /spl beta//spl ges/35 has been achieved for collector current densities ranging from J/sub c/=40 A/cm/sup 2/ to 239 A/cm/sup 2/ (I/sub c/=2.1 A) with a peak current gain of 38 at J/sub c/=114 A/cm/sup 2/.     

A multiwatt all gas-phase iodine laser (AGIL)

The demonstration and characterization of a multiwatt all gas-phase iodine laser (AGIL) are described. A 20-cm subsonic reactor was used to produce NCl (a/sup 1//spl Delta/) for series parametric studies of the I/sup */(/sup 2/P/sub 1/2/)-I(/sup 2/P/sub 3/2/) small-signal gain and extracted power dependence on reactant flow rates and reaction time. The highest measured gain was 2.5/spl times/10/sup -4/ cm/sup -1/ and the highest power observed was 15 W.     

MIM capacitors using atomic-layer-deposited high-/spl kappa/ (HfO/sub 2/)/sub 1-x/(Al/sub 2/O/sub 3/)/sub x/ dielectrics

Metal-insulator-metal (MIM) capacitors with (HfO/sub 2/)/sub 1-x/(Al/sub 2/O/sub 3/)/sub x/ high-/spl kappa/ dielectric films were investigated for the first time. The results show that both the capacitance density and voltage/temperature coefficients of capacitance (VCC/TCC) values decrease with increasing Al/sub 2/O/sub 3/ mole fraction. It was demonstrated that the (HfO/sub 2/)/sub 1-x/(Al/sub 2/O/sub 3/)/sub x/ MIM capacitor with an Al/sub 2/O/sub 3/ mole fraction of 0.14 is optimized. It provides a high capacitance density (3.5 fF//spl mu/m/sup 2/) and low VCC values (/spl sim/140 ppm/V/sup 2/) at the same time. In addition, small frequency dependence, low loss tangent, and low leakage current are obtained. Also, no electrical degradation was observed for (HfO/sub 2/)/sub 1-x/(Al/sub 2/O/sub 3/)/sub x/ MIM capacitors after N/sub 2/ annealing at 400/spl deg/C. These results show that the (HfO/sub 2/)/sub 0.86/(Al/sub 2/O/sub 3/)/sub 0.14/ MIM capacitor is very suitable for capacitor applications within the thermal budget of the back end of line process.     

New class of nonlinear systematic error detecting codes

A code C detects error e with probability 1-Q(e),ifQ(e) is a fraction of codewords y such that y, y+e/spl isin/C. We present a class of optimal nonlinear q-ary systematic (n, q/sup k/)-codes (robust codes) minimizing over all (n, q/sup k/)-codes the maximum of Q(e) for nonzero e. We also show that any linear (n, q/sup k/)-code V with n /spl les/2k can be modified into a nonlinear (n, q/sup k/)-code C/sub v/ with simple encoding and decoding procedures, such that the set E={e|Q(e)=1} of undetected errors for C/sub v/ is a (k-r)-dimensional subspace of V (|E|=q/sup k-r/ instead of q/sup k/ for V). For the remaining q/sup n/-q/sup k-r/ nonzero errors, Q(e)/spl les/q/sup -r/for q/spl ges/3 and Q(e)/spl les/ 2/sup -r+1/ for q=2.     

1677 V, 5.7 m/spl Omega//spl middot/cm/sup 2/ 4H-SiC BJTs

This letter reports the development of a high-performance power 4H-SiC bipolar junction transistor (BJT) with, simultaneously, a high blocking voltage and a low specific on-resistance (R/spl I.bar//sub ON/). A single BJT cell with an active area of 0.61 mm/sup 2/ achieves an open base collector-to-emitter blocking voltage (V/sub ceo/) of 1677 V and conducts up to 3.2 A at a forward voltage drop of V/sub CE/=3.0 V, corresponding to a low R/spl I.bar//sub ON/ of 5.7 m/spl Omega//spl middot/cm/sup 2/ up to Jc=525 A/cm/sup 2/ and a record high value of V/sub B//sup 2//R/sub SP/spl I.bar/ON/ of 493 MW/cm/sup 2/.     

The empirical distribution of rate-constrained source codes

Let X = (X/sub 1/,...) be a stationary ergodic finite-alphabet source, X/sup n/ denote its first n symbols, and Y/sup n/ be the codeword assigned to X/sup n/ by a lossy source code. The empirical kth-order joint distribution Q/spl circ//sup k/[X/sup n/,Y/sup n//spl rceil/(x/sup k/,y/sup k/) is defined as the frequency of appearances of pairs of k-strings (x/sup k/,y/sup k/) along the pair (X/sup n/,Y/sup n/). Our main interest is in the sample behavior of this (random) distribution. Letting I(Q/sup k/) denote the mutual information I(X/sup k/;Y/sup k/) when (X/sup k/,Y/sup k/)/spl sim/Q/sup k/ we show that for any (sequence of) lossy source code(s) of rate /spl les/R lim sup/sub n/spl rarr//spl infin//(1/k)I(Q/spl circ//sup k/[X/sup n/,Y/sup n//spl rfloor/) /spl les/R+(1/k)H (X/sub 1//sup k/)-H~(X) a.s. where H~(X) denotes the entropy rate of X. This is shown to imply, for a large class of sources including all independent and identically distributed (i.i.d.). sources and all sources satisfying the Shannon lower bound with equality, that for any sequence of codes which is good in the sense of asymptotically attaining a point on the rate distortion curve Q/spl circ//sup k/[X/sup n/,Y/sup n//spl rfloor//spl rArr//sup d/P(X/sup k/,Y~/sup k/) a.s. whenever P(/sub X//sup k//sub ,Y//sup k/) is the unique distribution attaining the minimum in the definition of the kth-order rate distortion function. Consequences of these results include a new proof of Kieffer's sample converse to lossy source coding, as well as performance bounds for compression-based denoisers.     

RF, DC, and reliability characteristics of ALD HfO/sub 2/-Al/sub 2/O/sub 3/ laminate MIM capacitors for Si RF IC applications

High-performance metal-insulator-metal capacitors using atomic layer-deposited HfO/sub 2/-Al/sub 2/O/sub 3/ laminate are fabricated and characterized for RF and mixed-signal applications. The laminate capacitor can offer high capacitance density (12.8 fF//spl mu/m/sup 2/) up to 20 GHz, low leakage current of 4.9/spl times/10/sup -8/ A/cm/sup 2/ at 2 V and 125/spl deg/C, and small linear voltage coefficient of capacitance of 211 ppm/V at 1 MHz, which can easily satisfy RF capacitor requirements for year 2007 according to the International Technology Roadmap for Semiconductors. In addition, effects of constant voltage stress and temperature on leakage current and voltage linearity are comprehensively investigated, and dependences of quadratic voltage coefficient of capacitance (/spl alpha/) on frequency and thickness are also demonstrated. Meanwhile, the underlying mechanisms are also discussed.     

InAlN/GaN HEMTs: a first insight into technological optimization

High-electron mobility transistors (HEMTs) were fabricated from heterostructures consisting of undoped In/sub 0.2/Al/sub 0.8/N barrier and GaN channel layers grown by metal-organic vapor phase epitaxy on (0001) sapphire substrates. The polarization-induced two-dimensional electron gas (2DEG) density and mobility at the In/sub 0.2/Al/sub 0.8/N/GaN heterojunction were 2/spl times/10/sup 13/ cm/sup -2/ and 260 cm/sup 2/V/sup -1/s/sup -1/, respectively. A tradeoff was determined for the annealing temperature of Ti/Al/Ni/Au ohmic contacts in order to achieve a low contact resistance (/spl rho//sub C/=2.4/spl times/10/sup -5/ /spl Omega//spl middot/cm/sup 2/) without degradation of the channels sheet resistance. Schottky barrier heights were 0.63 and 0.84 eV for Ni- and Pt-based contacts, respectively. The obtained dc parameters of 1-/spl mu/m gate-length HEMT were 0.64 A/mm drain current at V/sub GS/=3 V and 122 mS/mm transconductance, respectively. An HEMT analytical model was used to identify the effects of various material and device parameters on the InAlN/GaN HEMT performance. It is concluded that the increase in the channel mobility is urgently needed in order to benefit from the high 2DEG density.     

1330 V, 67 m/spl Omega//spl middot/cm/sup 2/ 4H-SiC(0001) RESURF MOSFET

Design and fabrication of 4H-SiC(0001) lateral MOSFETs with a two-zone reduced surface field structure have been investigated. The dose dependencies of experimental breakdown voltage show good agreement with simulation. Through the optimization of implant dose, high-temperature (1700/spl deg/C) annealing after ion implantation, and reduction of channel length, a breakdown voltage of 1330 V and a low on-resistance of 67 m/spl Omega//spl middot/cm/sup 2/ have been obtained. The figure-of-merit (V/sub B//sup 2//R/sub on/) of the present device reaches 26 MW/cm/sup 2/, being the best performance among lateral MOSFETs reported. The temperature dependence of static characteristics is also presented.     

Microwave noise performance of AlGaN-GaN HEMTs with small DC power dissipation

We report low microwave noise performance of discrete AlGaN-GaN HEMTs at DC power dissipation comparable to that of GaAs-based low-noise FETs. At 1-V source-drain (SD) bias and DC power dissipation of 97 mW/mm, minimum noise figures (NF/sub min/) of 0.75 dB at 10 GHz and 1.5 dB at 20 GHz were achieved, respectively. A device breakdown voltage of 40 V was observed. Both the low microwave noise performance at small DC power level and high breakdown voltage was obtained with a shorter SD spacing of 1.5 /spl mu/m in 0.15-/spl mu/m gate length GaN HEMTs. By comparison, NF/sub min/ with 2 /spl mu/m SD spacing was 0.2 dB greater at 10 GHz.     

Demonstration of 1789 V, 6.68 m/spl Omega/ /spl middot/ cm/sup 2/ 4H-SiC merged-PiN-Schottky diodes

The design, fabrication and characterisation of a high performance 4H-SiC diode of 1789 V-6.6 A with a low differential specific-on resistance (R/sub SP/spl I.bar/ON/) of 6.68 m/spl Omega/ /spl middot/ cm/sup 2/, based on a 10.3 /spl mu/m 4H-SiC blocking layer doped to 6.6/spl times/10/sup 15/ cm/sup -3/, is reported. The corresponding figure-of-merit of V/sub B//sup 2//R/sub SP/spl I.bar/ON/ for this diode is 479 MW/cm/sup 2/, which substantially surpasses previous records for all other MPS diodes.     

GaInAsSb/GaSb pn photodiodes for detection to 2.4 mu m

Ga/sub 0.77/In/sub 0.23/As/sub 0.20/Sb/sub 0.80//GaSb pn heterojunction photodiodes have been prepared by liquid phase epitaxy. They exhibit a long-wavelength threshold of 2.4 mu m. The room-temperature dark current at V=-0.5 V is 3 mu A (10 mA/cm/sup 2/) and the external quantum efficiency is around 40% in the wavelength range 1.75-2.25 mu m. The estimated detectivity D* at 2.2 mu m is 8.8*10/sup 9/ cm Hz/sup 1/2/ W/sup -1/.<>     

2 V-operated InGaP-AlGaAs-InGaAs enhancement-mode pseudomorphic HEMT

A low-voltage single power supply enhancement-mode InGaP-AlGaAs-InGaAs pseudomorphic high-electron mobility transistor (PHEMT) is reported for the first time. The fabricated 0.5/spl times/160 /spl mu/m/sup 2/ device shows low knee voltage of 0.3 V, drain-source current (I/sub DS/) of 375 mA/mm and maximum transconductance of 550 mS/mm when drain-source voltage (V/sub DS/) was 2.5 V. High-frequency performance was also achieved; the cut-off frequency(F/sub t/) is 60 GHz and maximum oscillation frequency(F/sub max/) is 128 GHz. The noise figure of the 160-/spl mu/m gate width device at 17 GHz was measured to be 1.02 dB with 10.12 dB associated gain. The E-mode InGaP-AlGaAs-InGaAs PHEMT exhibits a high output power density of 453 mW/mm with a high linear gain of 30.5 dB at 2.4 GHz. The E-mode PHEMT can also achieve a high maximum power added efficiency (PAE) of 70%, when tuned for maximum PAE.