共查询到20条相似文献,搜索用时 345 毫秒
1.
2.
采用水热法,以九水硝酸铁和尿素为原料成功制备出球状纳米氧化铁。以生物质葡萄糖为碳源,采用水热炭化法制备了碳包覆球状纳米氧化铁。在N2气氛下使用高温综合热分析仪测量了不同升温速率下的TG-DTA曲线,通过Flynn-Wall-Ozawa法和Coats-Redfern法相互验证确定碳包覆纳米氧化铁还原的动力学参数。结果表明:包覆生物质碳与纳米氧化铁在180℃就可以发生反应,降低了还原温度,反应活化能约为79.48 kJ/mol,反应模型为三维扩散模型。 相似文献
3.
4.
纳米铁及氧化铁粉制备技术的进展 总被引:2,自引:1,他引:1
纳米铁及氧化铁粉广泛用于磁记录、气敏元件、光吸收材料、高效催化等领域。近年来,纳米铁及氧化铁粉的制备技术和物性研究取得了较大进展,应用领域进一步扩展。该文着重介绍国内外纳米铁及氧化铁粉的几种基本制备方法及其关键技术的发展现状,并分析了用不同方法制备的纳米粉末的物理特性。 相似文献
5.
氧化铁的制备方法及其应用 总被引:2,自引:0,他引:2
随着高科技的迅速发展和对合成新材料的迫切需要,氧化铁的制备技术及其应用的开发已越来越受到重视.为此全面叙述了氧化铁的制备方法,分析了焙烧法、热分解法、鲁式法、溶胶-凝胶法、空气氧化法、水解法、沉淀法、水热法、催化法及包核法等各种制备工艺的优缺点.同时,详细地介绍了氧化铁在磁性材料、颜料、催化、生物医学及其他领域的应用.最后,针对目前氧化铁制备技术中存在的一些问题,提出了进一步研究的方向. 相似文献
6.
7.
8.
研究了低温还原微纳米氧化铁粉的还原特性与机理。用高能球磨法获得的微纳米氧化铁粉在280~400 ℃内用氢气还原,并测定还原后粉末中氧、计算氧化铁粉末的还原率,通过扫描电子显微镜来观察还原铁粉的形貌;找出了氧化铁粒度、还原温度和还原时间等参数对氧化铁还原率、铁粉粒度和粒度分布、铁粉形貌等的影响。从动力学的角度,探讨了粉末细化对低温氢气还原氧化铁活化能的影响。研究结果指出,微纳米氧化铁粉的还原反应遵循吸附自动催化理论,反应动力学遵循界面化学反应理论,研究获得了反应所对应的反应机制函数和相应的动力学方程。 相似文献
9.
研究了低温还原微纳米氧化铁粉的还原特性与机理。用高能球磨法获得的微纳米氧化铁粉在280~400 ℃内用氢气还原,并测定还原后粉末中氧、计算氧化铁粉末的还原率,通过扫描电子显微镜来观察还原铁粉的形貌;找出了氧化铁粒度、还原温度和还原时间等参数对氧化铁还原率、铁粉粒度和粒度分布、铁粉形貌等的影响。从动力学的角度,探讨了粉末细化对低温氢气还原氧化铁活化能的影响。研究结果指出,微纳米氧化铁粉的还原反应遵循吸附自动催化理论,反应动力学遵循界面化学反应理论,研究获得了反应所对应的反应机制函数和相应的动力学方程。 相似文献
10.
11.
考察了不同粒度下氧化皮的X射线衍射图谱,结果表明,270~400目粒度下氧化皮衍射峰强度最强。利用分析评估程序处理了氧化皮的X射线衍射图谱,并和PDF-2数据库(国际衍射数据中心)中数据进行比对,以找出其特征物相。结果表明,氧化皮的特征物相为三氧化二铁、四氧化三铁、氧化亚铁共存,而其它杂质物相含量极低。经过与天然铁矿石的特征物相进行比对,发现其中氧化亚铁物相是氧化皮区别于铁矿石的主要特征,因此氧化亚铁物相的存在可以作为鉴定铁矿石中是否掺杂氧化皮的重要指标,由此建立了铁矿石中氧化皮的X射线衍射鉴定方法,方法能够对含量高于10%的氧化皮进行鉴定。 相似文献
12.
13.
A. N. Titenko T. E. Lazurik L. S. Pugacheva A. P. Danil'chuk 《Powder Metallurgy and Metal Ceramics》1976,15(4):310-314
Conclusions It is shown that goethite (yellow ferrie oxide pigment) synthesis by an ammoniacal method offers a suitable means of obtaining, from technical iron vitriol, high-purity ferric oxide with stable properties fulfilling the requirements for ferrite-grade ferric oxide. The ferric oxide is distinguished by its high reactivity after high-temperature (850–900°C) heat treatment. Its physicochemical properties are close to those of 1360 WF grade ferric oxide manufactured by the Bayer Co. of West Germany [5]. The key process parameters in the production of ferric oxide by this method are: goethite synthesis pH 4.0–4.5, synthesis temperature 70–75°C, amount of seed 8–10% of the goethite content at the end of synthesis, and ferric oxide calcining temperature 850–900°C.Translated from Poroshkovaya Metallurgiya, No.4(160), pp. 82–88, April, 1976. 相似文献
14.
A simple method was developed to produce the nanocrystalline pure iron by aluminothermic reaction casting.The microstructure of the iron was investigated by optical microscope(OM),transmission electron microscope(TEM),electron probe micro-analyzer(EPMA),scanning electron microscope(SEM)and X-ray diffraction(XRD).The mechanical performances of nanocrystalline pure iron were tested.It is found that the pure iron consists of nanocrystalline ferrite.For different substrates of copper and glass,the average grain size of the ferrite was 38 and 35 nm,respectively,which is larger on copper substrate than that on glass.The hardness,compressive strength,tensile strength,and total elongation are 167 and 137HB,400 and 500MPa,243 and 185MPa,16%and10% on copper substrate and glass substrate,respectively.The hardness,tensile strength and total elongation are all larger on copper substrate than those on glass substrate,while the compressive strength is lower.The large supercooling in the product solidification provides the condition for high nucleation rate and thus leads to nano-grained austenite and final nano-grained ferrite transformed from those small austenite grains. 相似文献
15.
对铁帽型含金复合矿煤整直接还原过程中铁氧化物行为进行了研究,并用粉晶X-射线衍射对其反应机理进行验证。结果表明:直接还原过程中,不仅包括铁氧化物的还原相变,同时还存在铁氧化物同其它氧化物之间的固相反应。 相似文献
16.
线材的氧化铁皮起着保护线材免锈蚀的作用,但是也需要在酸洗时容易除去。影响铁皮除去或结合力的主要是铁皮的厚度和其物相结构。通过对不同轧制条件下的氧化铁皮厚度、物相结构进行检测分析,研究了精轧温度和吐丝温度对φ12 mm SCM435氧化铁皮物相结构的影响。研究表明,随着精轧温度或吐丝温度的升高,SCM435线材的氧化铁皮厚度均会增加,且在800-900℃短时间就会生成较厚(约20μm)的氧化铁皮;由于Cr的氧化选择性,精轧温度在870℃以上,吐丝温度在810℃以上时,随精轧温度或吐丝温度升高,氧化铁皮中FeO比例提高;但是吐丝温度高于860℃后,物相结构的变化趋缓,FeO的比例变化不大。 相似文献
17.
V. B. Kul’met’eva S. E. Porozova E. S. Gnedina 《Russian Journal of Non-Ferrous Metals》2013,54(3):239-245
Technology for the synthesis of nanocrystalline zirconium dioxide powder stabilized with yttrium oxide by joint deposition is developed. This technology makes it possible to sinter ceramics based on this powder at temperatures below 1400°C. Characteristics of the zirconia powder (depending on the synthesis conditions) are investigated using X-ray diffraction, the thermal desorption of nitrogen, and electron microscopy. It is revealed that the ultrasonic (US) effect achieved when washing the gel-like powder, as well as crushing the powder after drying and calcination, make it possible to decrease the degree of its agglomeration and decrease the agglomerate size. It is established based on the data of the thermochemical analysis that a decrease in the heating rate to the isothermal holding temperature during synthesis can decrease the liability of the ceramics made from the nanocrystalline zirconia powder to zonal sintering. 相似文献
18.
19.
Metallurgist - Bulk nanocomposite granules based on AlMg2 alloy, containing nanocrystalline graphite, are prepared by mechanical synthesis using a high-energy ball mill. Structural and phase... 相似文献
20.
纳米WC-Co复合粉末的制备工艺及其烧结特性 总被引:16,自引:2,他引:14
综述了纳米WC-Co复合粉末制备工艺的国内外研究进展,总结了纳米WC-Co硬质合金复合粉末的烧结特性,并对目前国内外的研究现状进行了分析,指出了研究中所存在的问题和研究趋势。 相似文献