Effect of solvent on electrical conductivity and gas sensitivity of PEDOT: PSS polymer composite films

Poly(3,4‐ethylenedioxythiophene)/poly(styrene sulfonate) (PEDOT:PSS) was blended with polyethylene oxide (PEO) and polyvinyl alcohol (PVA) and composite film was cast. Additional solvents of dimethyl sulfoxide (DMSO) and ethylene glycol (EG) were mixed and their effects on electrical conductivity and structural changes were investigated. The electrical conductivity increased in response to the additional solvent, leading to an increase in the PEDOT ratio relative to the control. PEDOT:PSS/PEO composite film had a much higher electrical conductivity than PEDOT:PSS/PVA. When blended with PEO, the quinoid structure revealed by Raman spectroscopy increased relative to the PVA‐blended case, indicating higher electrical conductivity. The current–voltage response and gas sensitivity showed much better performance in PEDOT:PSS/PEO/DMSO composite film. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42628.     

Enhanced thermoelectric performance of poly(3,4‐ethylenedioxythiophene):poly(4‐styrenesulfonate) (PEDOT:PSS) with long‐term humidity stability via sequential treatment with trifluoroacetic acid

This paper reports a range of effective sequential chemical processes to enhance the thermoelectric performance of conducting poly(3,4‐ethylenedioxythiophene) films doped with poly(styrene sulfonate) anions (PEDOT:PSS). The electrical conductivity of the PEDOT:PSS films was significantly increased from 0.33 to 3748 S cm^?1 after a series of sequential treatments with trifluoroacetic acid (TFA) while the Seebeck coefficient and thermal conductivity were slightly reduced from 17.5 ± 1.2 to 16.0 ± 1.1 μV K^?1 and 0.537 to 0.415 W m^–1 K^?1 for the pristine film and treated film, respectively, leading to a significant improvement in power factor up to 97.1 ± 5.4 μW m^–1 K^?2. More importantly, around 80% of the electrical conductivity and Seebeck coefficient was retained after 20 days for these TFA‐treated PEDOT:PSS films, revealing the potential for real thermoelectric applications. © 2019 Society of Chemical Industry     

Enhanced thermoelectric properties of poly(3,4-ethylenedioxythiophene): Poly(styrenesulfonate)/copper phthalocyanine disulfonic acid composite films

A series of poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate)/copper phthalocyanine disulfonic acid (PEDOT: PSS/CuPc-[SO₃H]₂) composite films were prepared by using CuPc-(SO₃H)₂ as the dopant. EG treatment was applied to further improve the thermoelectric properties of PEDOT: PSS/CuPc-(SO₃H)₂ composites. Structural analyses indicated the strong π − π interactions existed between PEDOT: PSS and CuPc-(SO₃H)₂, and led to more ordered regions in the composite films, and benefit the conductivity. CuPc-(SO₃H)₂ can greatly improve the thermoelectric properties of PEDOT: PSS/CuPc-(SO₃H)₂ composite films, which have a Seebeck coefficient of 13.2 μV K⁻¹ and a conductivity of 2.8 × 10⁵ S/m with 20 wt% CuPc-(SO₃H)₂ at room temperature, and the corresponding power factor is 48.8 μW m⁻¹ K⁻², which is almost 6.83 times higher than the PEDOT: PSS films without CuPc-(SO₃H)₂.     

Enhanced Thermoelectric Performance of PEDOT:PSS Films by Sequential Post‐Treatment with Formamide

This paper reports a series of sequential post‐treatments using a polar solvent formamide to enhance the thermoelectric performance of poly(3,4‐ethylenedioxythiophene) doped with poly(styrene sulfonate) anions (PEDOT:PSS). The electrical conductivity of PEDOT:PSS films significantly increases from 0.33 S cm^?1 for the pristine film to ≈2929 S cm^?1 for the treated film and meanwhile the Seebeck coefficient maintains as high as 17.4 µV K^?1, resulting in a power factor of 88.7 µW m^?1 K^?2. Formamide is a polar solvent with a high boiling point of 210 °C and high dielectric constant of 109, and PSS has a good solubility in it. Post‐treatment with formamide causes not only the phase segregation of PEDOT and PSS but also the removal of insulating PSS, therefore leading to the reorientation of PEDOT chains and enhancement in mobility without altering the doping level considerably. The cross‐plane thermal conductivity also reduces from 0.54 to 0.19 W m^?1 K^?1 after the post‐treatment, leading to a figure of merit (ZT) value of 0.04 at room temperature.     

Electrically conductive poly(3,4‐ethylenedioxythiophene)–polystyrene sulfonic acid/polyacrylonitrile composite fibers prepared by wet spinning

Composite conductive fibers based on poly(3,4‐ethylenedioxythiophene) (PEDOT)–polystyrene sulfonic acid (PSS) blended with polyacrylonitrile (PAN) were prepared via a conventional wet‐spinning process. The influences of the PEDOT–PSS content on the electrical conductivity, thermal stability, and mechanical properties of the composite fibers were investigated. The fibers with 1.83 wt % PEDOT–PSS showed a conductivity of 5.0 S/cm. The breaking strength of the fibers was in the range 0.36–0.60 cN/dtex. The thermal stability of the PEDOT–PSS/PAN composite fibers was similar to but slightly lower than that of the pure PAN. The X‐ray diffraction results revealed that both the pure PAN and PEDOT–PSS/PAN composite fibers were amorphous in phase, and the crystallization of the latter was lower than that of the former. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Electrical conductivity enhancement of spin‐coated PEDOT:PSS thin film via dipping method in low concentration aqueous DMSO

The electrical conductivity of poly(3,4‐ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) was enhanced by dipping the thin films prepared by spin coating technique in an aqueous DMSO solution. The low concentration range of DMSO in water between 0–5 vol % was studied in comparison with pure water and pure DMSO. It was found that the electrical conductivity dramatically increased as increasing the concentration of DMSO and reached the constant value of 350 S cm^?1 at 2 vol % of aqueous DMSO solution. This could be explained by the conformational change of PEDOT chains from the coil structure to the linear or expanded coil structure as confirmed by Raman spectra. Further, white patches were obviously noticed on the surface of the films dipped in pure DMSO, indicating the phase separation of conductive PEDOT grains and associated PSS. The sulfur element of the dipped film surface was investigated by XPS. The XPS S2p core‐level spectra displayed that the unassociated PSS was considerably removed from the surface of PEDOT:PSS films dipped in pure water and 2 vol % of aqueous DMSO solution, indicating that the presence of water in the solvents is important to prominently promote the washing effect. Finally, UV–Vis spectra revealed the improved transparency of the films probably owing to the decreased film thickness. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42108.     

A novel hierarchical Pt- and FTO-free counter electrode for dye-sensitized solar cell

A novel hierarchical Pt- and FTO-free counter electrode (CE) for the dye-sensitized solar cell (DSSC) was prepared by spin coating the mixture of TiO₂ nanoparticles and poly(3,4-ethylenedioxy-thiophene):poly(styrenesulfonate) (PEDOT:PSS) solution onto the glass substrate. Compared with traditional Pt/FTO CE, the cost of the new CE is dramatically reduced by the application of bilayer TiO₂-PEDOT:PSS/PEDOT:PSS film and the glass substrate. The sheet resistance of this composite film is 35 Ω sq⁻¹ and is low enough to be used as an electrode. The surface morphologies of TiO₂-PEDOT:PSS layer and modified PEDOT:PSS layer were characterized by scanning electron microscope, which shows that the former had larger surface areas than the latter. Electrochemical impedance spectra and Tafel polarization curves prove that the catalytic activity of TiO₂-PEDOT:PSS/PEDOT:PSS/glass CE is higher than that of PEDOT:PSS/FTO CE and is similar to Pt/FTO CE''s. This new fabricated device with TiO₂-PEDOT:PSS/PEDOT:PSS/glass CE achieves a high power conversion efficiency (PCE) of 4.67%, reaching 91.39% of DSSC with Pt/FTO CE (5.11%).     

Effect of silver decorated graphene oxide on the PEDOT:PSS-matrix composite films

Silver decorated graphene oxide (GO) was added in poly(3,4-ethylenedioxythiopphene): poly(styrene sulfonate) (PEDOT:PSS) matrix to fabricate composite films, aiming for an improved electrical conductivity. Silver particles were deposited on GO surfaces by reaction with Tollens’ reagent. The composite films reinforced by silver decorated GO showed a sheet resistance of 744 Ω/sq. with 88.9% transparency, which outperformed PEDOT:PSS matrix and GO/PEDOT:PSS composite films. The deposited silver particles were consisted of elementary silver and positively charged silver. The GO surfaces were negatively charged. The distinction of positive domain and negative domain on silver decorated GO surfaces promoted the phase separation of conductive PEDOT molecules and insulting PSS molecules, which contributed to the increase of the electrical conductivity of the composite films. Moreover, the deposition of elementary silver introduced extra electron pathways in the composite films.     

Electrical conductivity of polymer blends of poly(3,4-ethylenedioxythiophene): Poly(styrenesulfonate): N-methyl-2-pyrrolidinone and polyvinyl alcohol

The goal of this study is to determine the electrically conductivity of the polymers poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate): N-methyl-2-pyrrolidinone (PEDOT: PSS: NMP) and PEDOT: PSS when blended with polyvinyl alcohol (PVA). While the conducting polymers have high conductivity when not blended with PVA, they are brittle and difficult to spin-coat. Thus, the motivation for this study is to develop blends of these two conducting polymers with PVA to produce a material with optimized mechanical properties and that can also be spin-coated. The blends are produced using aqueous preparations of these materials. Mixtures of various weight percentages (wt %) of PEDOT: PSS: NMP and PEDOT: PSS are prepared and spin-coated on glass slides to form thin films. In the blends, the film conductivity increases with increasing content of either PEDOT: PSS: NMP or PEDOT: PSS. For example, 100 wt % of PEDOT: PSS: NMP and 60 wt % of PEDOT: PSS: NMP blended with PVA exhibit conductivities of, respectively, 10 and 4.02 S/cm. In contrast, conductivities of only 0.0525 and 0.000506 S/cm are observed, respectively, for 100 wt % of PEDOT: PSS and 60 wt % of PEDOT: PSS content in the PEDOT: PSS/PVA blends (No NMP). The addition of the NMP enhances the electrical conductivity by two to five orders of magnitude (depending on the amount of PVA in the blend) due to conformational change of PEDOT chains. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Capacitance properties of graphite oxide/poly(3,4‐ethylene dioxythiophene) composites

Poly(3,4‐ethylene dioxythiophene) (PEDOT) and graphite oxide (GO)/PEDOT composites (GPTs) doped with poly(sodium styrene sulfate) (PSS) were synthesized by in situ polymerization in aqueous media. The electrochemical capacitance performances of GO, PEDOT–PSS, and GPTs as electrode materials were investigated. The GPTs had a higher specific capacitance of 108 F/g than either composite constituent (11 F/g for GO and 87 F/g for PEDOT–PSS); this was attributable to its high electrical conductivity and the layer‐within/on‐layer composite structure. Such an increase demonstrated that the synergistic combination of GO and PEDOT–PSS had advantages over the sum of the individual components. On the basis of cycle‐life tests, the capacitance retention of about 78% for the GPTs compared with that of 66% for PEDOT–PSS after 1200 cycles suggested a high cycle stability of the GPTs and its potential as an electrode material for supercapacitor applications. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Growth of hexagonal polyaniline fibers with polyacrylamide pendants

A new concept of synthesizing hexagonal polyaniline (PANi) fibers with polyacrylamide (PAAm) pendants in PAAm oligomer (oligo‐PAAm) colloid is proposed. The size and morphology of the composite fibers can be controlled by adjusting the synthesis conditions. A possible growth mechanism of the PANi microstructures based on typical PAAm–crystals interactions in a mild aqueous solution is proposed. The amide ligands decorated oligo‐PAAm chains are able to coordinate with –C₆H₄–NH⁺C₆H₄NH⁺–C₆H₄–NH–C₆H₄–NH– sections, leading to a lower surface energy and growth along c‐directions to form fibriform morphology. The fibers have uniform diameter ranging from 200 to 400 μm, and length varying from several millimeters to 6 cm. Fourier transform infrared measurement indicates that the fiber exhibits a main PANi chain with PAAm pendants, and ultraviolet–visible spectra reveal that the PANi is in high conductive emeraldine state. Acrylamide feed significantly affects the morphology, however, the conductivity and yield of the fiber depend on hydrochloric acid and potassium peroxydisulfate concentrations in the preparation process. The hexagonal composite fibers show an electrical conductivity of 2.2 S·cm⁻¹ and yield of higher than 95%. Polymer‐directed crystal growth may provide promising routes to rational synthesis of various ordered organic materials with complex form and structural specialization. POLYM. COMPOS., 35:253–262, 2014. © 2013 Society of Plastics Engineers     

Enhanced thermoelectric performance by alcoholic solvents effects in highly conductive benzenesulfonate‐doped poly(3,4‐ethylenedioxythiophene)/graphene composites

Benzenesulfonate‐doped poly(3,4‐ethylenedioxythiophene) (PEDOT‐Bzs)/graphene thermoelectric (TE) composites with various graphene filler contents were synthesized in five different kinds of solvents. Dodecylbenzenesulfonic acid (DBSA) was used to achieve good dispersion of graphene into the PEDOT matrix. Among the synthesized PEDOT materials, the one synthesized in methanol (PEDOT‐MeOH) had the highest electrical conductivity. X‐ray photoelectron spectroscopy (XPS) analysis showed almost the same charge carrier concentration for all PEDOT materials. However, the X‐ray diffraction (XRD) analysis highlighted the enhancement of PEDOT chain stacking by shorter‐chain alcoholic solvents, as a result of which the carrier mobility and electrical conductivity were increased. The electrical conductivity and the Seebeck coefficient of the PEDOT/graphene composites were significantly improved with increasing the graphene content, which strongly depended on increased carrier mobility. The thermal conductivity of the composites exhibited relatively small changes, attributed to phonon scattering effects. The maximum TE efficiency of the PEDOT‐MeOH/graphene composite with 75 wt % graphene showed a substantially improved value of 1.9 × 10^?2, higher than that of the other PEDOT/graphene composites. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42107.     

Preparation and characterization of graphene composites with conducting polymers

We report a new route for preparing electro‐conductive composites based on reduced graphene oxide (RG‐O) and poly(3,4‐ethylenedioxythiophene) (PEDOT). The composites were prepared by in situ polymerization of EDOT in aqueous mixture containing RG‐O platelets modified with poly(sodium 4‐styrenesulfonate) (PSS). In the synthetic process, PSS molecules stabilize RG‐O in the aqueous phase and function as a polymerization template to hybridize PEDOT chains along RG‐O platelets. Compared with the RG‐O platelets, the resulting composites show an enhanced electrical conductivity of 9.2 S cm^?1 with good thermal stability. Copyright © 2011 Society of Chemical Industry     

Phase equilibrium of the ternary system of NH<Subscript>4</Subscript>Cl-CaCl<Subscript>2</Subscript>-H<Subscript>2</Subscript>O at 50°C

The equilibrium data on the ternary system of NH₄Cl—CaCl₂—H₂O at 50°C were investigated using the wet-residue method. The experimental results show that there are three pure phase crystal areas of NH₄Cl, 2NH₄Cl·CaCl₂·3H₂O and CaCl·2H₂O, two mixture phase crystal areas of NH₄Cl and 2NH₄Cl·CaCl·3H₂O, and 2NH₄Cl ·CaCl₂·3H₂O and CaCl·2H₂O in the system. A new hydration double salt (2NH₄Cl·CaCl·3H₂O) was found in the ternary equilibrium system for the first time.     

High cycling stability and well printability poly(3,4‐ethylenedioxythiophene):poly(styrene sulfonate)/multi‐walled carbon nanotube nanocomposites via in situ polymerization applied on electrochromic display

A high cycling stability material and an additive manufacturing method are reported for the fabrication of solid electrochromic devices. The poly(3,4‐ethylenedioxythiophene):poly(styrene sulfonate)/multi‐walled carbon nanotube (PEDOT:PSS/MWCNT) nanocomposites were synthesized via in situ polymerization. A carboxymethyl cellulose gel was used as the ink vehicle for screen printing. The electrochromic (EC) performance of films patterned by screen printing was also examined. The results of characterization indicate that strong interfacial interactions occurred between PEDOT:PSS and the MWCNTs and the MWCNTs formed a network in these conducting polymers film, so the composite was more conductive than pure PEDOT:PSS. Devices containing PEDOT:PSS/MWCNTs were more stable after 1000 cycles, exhibited higher rate of ion exchange and faster increases in current. The composite containing 0.3 wt % MWCNTs also had a 23% higher color contrast (ΔE*) than pure PEDOT:PSS at 2.5 V applied voltages. The EC inks with well printability not only can be used to print large area films, but also can print fine lines and pixel‐type dots in displays. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45943.     

On the mechanism of conductivity enhancement in PEDOT/PSS film doped with multi-walled carbon nanotubes

The results of conductivity investigation of poly(3,4-ethylenedioxythiophene)/poly(styrene sulfonic acid) (PEDOT/PSS) thin films doped with different multi-walled carbon nanotubes (MWCNTs) concentrations were studied. The role of MWCNTs as a conductive filler on the mechanism of conductivity enhancement in the composite film was further investigated by X-ray diffraction (XRD), Fourier transform Roman spectroscopy (FT-RM), X-ray photoelectron spectroscopy (XPS) and Atomic force microscopy (AFM). The increase of the conductivity is likely to be due to two effects, the “π-π interaction” effect and the “channel” effect. The former is π-π interaction between the thiophene rings of PEDOT backbone and MWCNTs, and the electronic density transfer occurs from PEDOT to MWCNTs in M-PEDOT/PSS, so that the charge becomes more delocalized on the PEDOT chains. The latter stems from the formation of some conductive MWCNTs channels in the PEDOT/PSS matrix. These two effects can help charge transport and enhance the conductivity of composite films.     

A focus on polystyrene tacticity in synthesized conductive PEDOT:PSS thin films

Poly(3,4-ethylenedioxythiophene):poly (styrenesulfonate) (PEDOT:PSS) is a transparent conductive material and a good candidate for being employed as substitute for indium tin oxide (ITO) in reducing the production costs of organic solar cells. To enhance the performance of organic devices, an improving in the conductivity of PEDOT:PSS is crucial and using the solvent additive rises the electrical conductivity by the optimization of the film morphology. The studies have only focused on the relationship between the electrical conductivity of thin films and the crystallinity of PEDOT, and it is also found that the high conductivity is observed in the highly crystalline samples. This study focused on the effect of tacticity of PS on the conductivity of PEDOT:PSS films. First, atactic and isotactic polystyrenes were sulfonated and the complexes of PEDOT:PSS were synthesized. The N-methylpyrrolidone (NMP), as a secondary dopant, was then added to the complexes and conductivity enhancement was investigated in various annealing times. The obtained films were characterized by atomic force microscopy, X-ray diffraction, four point probe resistivity measurement system, UV–visible spectroscopy, FT-IR, and cyclic voltammetry. The electrical conductivity of PEDOT:iPSS films synthesized by the isotactic polystyrene was ~ 0.68 S/cm and by adding 5 wt% NMP into PEDOT:PSS solution, the conductivity of the annealed thin layers increased more than 10-folds (~ 7.73 S/cm) at an appropriate temperature.     

Phase equilibrium of the ternary system of NH4Cl-CaCl2-H2O at 50°C

The equilibrium data on the ternary system of NH₄Cl—CaCl₂—H₂O at 50°C were investigated using the wet-residue method. The experimental results show that there are three pure phase crystal areas of NH₄Cl, 2NH₄Cl·CaCl₂·3H₂O and CaCl·2H₂O, two mixture phase crystal areas of NH₄Cl and 2NH₄Cl·CaCl·3H₂O, and 2NH₄Cl ·CaCl₂·3H₂O and CaCl·2H₂O in the system. A new hydration double salt (2NH₄Cl·CaCl·3H₂O) was found in the ternary equilibrium system for the first time.     

Effect of microstructure on the dielectric properties of poly(vinyl alcohol)–poly(3,4‐ethylenedioxythiophene) doped with poly(styrenesulfonate) composite films

Poly(3,4‐ethylenedioxythiophene) doped with poly(styrenesulfonate) (PEDOT–PSS) was blended with poly(vinyl alcohol) (PVA) to form 0, 10, 20, 30, 40, and 50 vol % PEDOT–PSS/PVA solutions, and their freestanding films were prepared with a simple and cost‐effective solution casting technique at 27 °C in the absence of additives. Field emission scanning electron microscopy images revealed changes in the cocontinuous network to a rodlike morphology in the composite films from 10 to 50 vol % PEDOT–PSS/PVA. The alternating‐current conductivity was found to obey Jonscher's power law. The obtained values of the dielectric constant at 27 °C were relatively high, and a maximum value of 6.7 × 10⁴ at 100 Hz for 40 vol % PEDOT–PSS'/PVA was observed. The dielectric loss attained a maximum value of about 10⁶ at 100 Hz for 40 vol % PEDOT–PSS/PVA. However, a decrease in the dielectric parameters was observed at 50 vol % PEDOT–PSS/PVA because of locally induced strain in the microstructure. The variations in polarization with respect to the applied electric field (P–E) were determined for 50, 100, and 500 Hz at 500 V for the freestanding composite films of lower concentrations up to 20 vol % PEDOT–PSS/PVA. In summary, the dielectric and P–E measurements confirmed that the electrical characteristics changed in accordance to the contribution from both resistive and capacitive sites in the PEDOT–PSS/PVA composites. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45079.     

Preparation of surface initiated polystyrenesulfonate films and PEDOT doped by the films

Various substrates such as glass slides and silicon wafers were modified by styrylethyltrimethoxysilane to attach double bonds to those surfaces. The double bond layer was initiated and capped by benzoyl peroxide (BPO) and 2,2,6,6-tetramethylpiperidirooxy (TEMPO), respectively, to form ‘living’ free radical layer from which polystyrene brushes were grown. The density of double bonds on the surface controlled the orientation of polystyrene brush or film. The polystyrene films were then sulfonated by fuming sulfuric acid (H₂SO₄·xSO₃) to obtain polystyrenesulfonic acid (PSS) films with controlled polymer chain alignment. The lower double bond density led to a lower degree of polymer chain alignment. 3,4-Ethylenedioxythiophene monomer was diffused into PSS film and then polymerized. A conductive polyethylenedioxythiophene (PEDOT)/PSS film was obtained. The films were characterized by four-point probe, AFM and UV-VIS. The conductivity of PSS/PEDOT film measured along the direction which is normal to polymer chain alignment, is lower than that from commercial PSS/PEDOT.