不同制备方法对CeO2-ZrO2-Al2O3材料性能的影响

分别采用共沉淀法、胶溶法和胶溶?共沉淀法制备了Ce0.5Zr0.5O2(12wt%)-Al2O3(CZA)储氧材料,并通过XRD、低温N2吸附?脱附、氧脉冲吸附(OSC)、程序升温还原(H2-TPR)和O2-程序升温脱附(O2-TPD)等手段进行了表征.材料经过1000℃焙烧后,XRD结果表明,三种方法制备的样品均存在CeO2-ZrO2立方萤石和γ-Al2O3两种晶型.N2吸附?脱附结果表明,胶溶?共沉淀法制备的样品,具有最大的比表面积和孔容,分别为146.2m2/g和0.5mL/g,且有最佳的孔径分布;氧脉冲吸附(OSC)和H2-TPR结果表明胶溶?共沉淀法制备的材料,具有最佳的储氧性能和还原能力;同时实验还比较了经1100℃焙烧对几种方法制备样品性能的影响.     

Sm2O3掺杂(Ba0.7Ca0.3)TiO3-Ba(Zr0.2Ti0.8)O3无铅压电陶瓷的制备与性能

采用固相合成法制备了Sm2O3掺杂的(Ba0.7Ca0.3)TiO3-Ba(Zr0.2Ti0.8)O3(BCZT)无铅压电陶瓷.借助XRD、SEM等手段对该陶瓷的显微结构与电性能进行了研究.结果表明,Sm2O3的掺杂降低了BCZT无铅压电陶瓷的烧结温度并使居里温度点Tc从85℃提高到95℃.当Sm2O3掺杂量为0.02wt%～0.1wt%时,样品具有典型ABO3型钙钛矿结构.Sm2O3掺杂量为0.02wt%时,所得陶瓷样品具有最优综合电性能,其压电常数d33、机电耦合系数kp、机械品质因子Qm、介电损耗tanδ和介电常数εr分别为590 pC/N、0.52、43、1.3%和3372.     

Li2CO3-B2O3-V2O5掺杂ZnO-TiO2陶瓷低温烧结的研究

以Li2CO3、B2O3和V2O53种常见的低熔点氧化物为烧结助剂,用传统固相法制备了Li2CO3-B2O3-V2O5掺杂的ZnO-TiO2微波介质陶瓷,并利用XRD、SEM等研究了ZnO-TiO2陶瓷的烧结行为、物相组成、显微结构特征及微波介电性能等。结果表明,当掺入3%(质量分数)Li2CO3-B2O3-V2O5时,在840℃烧结2h可制备出体积密度为4.99g/cm3的ZnO-TiO2陶瓷,达到理论密度的96.5%以上,εr、Q.f、τf分别约为24、22900GHz、-4×10-6/℃。     

静电纺丝制备Fe2O3-TiO2纳米纤维及光催化性能研究

采用静电纺丝法制备了Fe2O3掺杂纳米TiO2的有机无机PVP/Fe2O3-TiO2纤维,经高温焙烧得到Fe2O3-TiO2纳米纤维。利用差动-热重(DSC-TGA)、傅里叶红外光谱(FT-IR)、扫描电镜(SEM)、XRD和比表面积分析仪等对样品进行了表征。以10mg/L亚甲基蓝溶液为底物,研究了Fe2O3掺杂量和焙烧温度等对亚甲基蓝太阳光催化降解效果的影响。结果表明,掺杂量为0.08%、焙烧温度为500℃得到的Fe2O3-TiO2纳米纤维光降解效果最好,达到96.3%,重复使用7次降解率仍在90%以上。     

掺杂钇铋Ce-Zr-Al储氧材料的制备及性能研究

采用共沉淀法制备了掺杂Y3+、Bi3+的CeO2-ZrO2-Al2O3(CZA)储氧材料,并通过XRD、低温N2吸附-脱附、氧脉冲吸附(OSC)及H2-TPR等手段进行了表征.XRD结果表明,600℃和1000℃焙烧后,Y3+、Bi3+的加入没有改变物相结构,所有样品均形成单一立方相萤石结构固溶体.低温N2吸附结果表明,Y3+掺杂的Ce0.6Zr0.3Y0.1O1.95-Al2O3(CZYA)材料,其织构性能及热稳定性都有很大的改善,1000℃老化5h后,比表面积和孔容可分别达80.75m2/g和0.22mL/g.OSC和H2-TPR结果表明,同时掺杂Y3+、Bi3+的Ce0.6Zr0.2Y0.1Bi0.1O1.9-Al2O3(CZYBA)材料,其储氧性能明显增强,经600和1000℃焙烧后分别达到461和242μmol/g;同时掺杂Y3+、Bi3+增强了CZA材料的还原性能,1000℃老化5h后还原峰温度从546℃降低到429℃.     

负载型Fe2O3/γ-Al2O3催化剂的制备及其对煤微波热解的催化活性

为实现低变质煤资源化的目标,在低变质煤微波热解的基础上采用超声浸渍-焙烧法制备负载型Fe2O3/γ-Al2O3催化剂,采用场发射扫描电镜(SEM)及X射线能谱(EDS)对催化剂进行表征,研究了其对煤微波热解过程中的催化效果及机理,考察焙烧时间、焙烧温度等因素对催化剂催化活性的影响,通过气-质联用(GC-MS)及煤气分析仪对焦油及气体组分和含量进行测定。结果表明,Fe2O3/γ-Al2O3催化剂的加入提高了煤微波热解制氢气及焦油产率,超声浸渍条件下400℃焙烧4h制备的产品催化活性最佳。     

Al2O3掺杂对Ba4Sm9.33Ti18O54陶瓷显微结构和介电性能的影响

采用固相反应法制备了Ba4Sm9.33Ti18O54(简称BST)xwt%Al2O3(x=0~1.5)微波介质陶瓷.研究了掺杂Al2O3对BST陶瓷的显微结构和介电性能的影响.扫描电镜和能谱分析结果显示:未掺杂的BST陶瓷中有少量Sm2Ti2O7相,随着增加Al2O3掺入量,Sm2Ti2O7相消失,BST陶瓷中先后产生了BaTi4O9(x≥0.6)和BaAl2Ti5O14(x≥1.0)两种新相.介电性能测试结果表明Sm2Ti2O7相的消失以及少量BaTi4O9相的形成,能显著提高BST陶瓷的Qf值,但会降低陶瓷的介电常数.当Al2O3的掺入量从0.6wt%增加到1.0wt%时,BaTi4O9相的量逐渐增加,引起BST陶瓷的Qf值略微下降.BaAl2Ti5O14相的产生会同时降低BST陶瓷的介电常数和Qf值.掺入0.6wt%Al2O3的BST陶瓷在1340℃烧结3 h后具有最佳的介电性能:εr=74.7,Qf=10980 GHz,τf=–11.8×10-6/℃.     

ZnO-Nb2O5掺杂SnO2基陶瓷研究

通过常压烧结制备SnO2基陶瓷,研究了ZnO、Nb2O5单掺杂及ZnO-Nb2O5复合掺杂对SnO2基陶瓷的烧结性能及电阻率的影响。采用SEM及XRD对试样分别进行了微观结构观察及物相分析。研究表明,掺杂ZnO能提高陶瓷的体积密度,但对于降低电阻率的影响不明显,当ZnO掺杂量在0.5%～0.75%(质量分数)时,SnO2基体积密度可达到6.67～6.73g/cm3;掺杂Nb2O5不能有效提高烧成陶瓷的体积密度,但能显著降低SnO2基陶瓷的电阻率;0.5%(质量分数)ZnO～1.5%(质量分数)Nb2O5复合掺杂在1450℃下烧成的陶瓷可得到较好的性能,其体积密度可达到6.61g/cm3,常温电阻率为867.84Ω.cm。     

La2O3/γ-Al2O3复合产物的浸渍-燃烧法制备及表征

采用浸渍-燃烧法制备了La2O3/γ-Al2O3复合产物,原料为La(NO3)3.6H2O(A.R)、一水合柠檬酸和工业级的拟薄水铝石.以六水合硝酸镧和一水合柠檬酸分别为镧源和燃烧剂,柠檬酸与六水硝酸镧的摩尔比为5∶6左右.将拟薄水铝石研磨成粉末并溶于柠檬酸和镧的配合物溶液中,搅拌至凝胶状,110℃干燥2h,再放入马弗炉中焙烧2 h得到产物.采用XRD、BET、XPS进行分析和表征,结果表明La3+的加入提高了γ-Al2O3的热稳定性,随着样品焙烧温度升高,比表面积下降,孔容、孔径变大.随着La3+的量的增加,样品的比表面积增大,孔径尺寸分布变宽.通过控制La3+加入的量以及焙烧温度,可调控多孔γ-Al2O3粉体的比表面积、孔容、孔径大小及孔径分布.     

MgO/Al2O3吸附剂对CO2静态吸附性能研究

采用等体积浸渍法制备MgO/Al2O3吸附剂。利用X光电子衍射(XRD)、氮气吸附、原位红外吸附等手段对材料的结构进行表征,通过静态吸附的方法对其吸附性能进行了测定。实验结果表明,所得到的MgO/Al2O3吸附剂,主要存在3个不同的碱性位,CO2吸附后主要是以碳酸氢盐、双齿碳酸盐和单齿碳酸盐的形式存在的。当MgO的负载量为10wt%时,其对CO2的吸附量是最大的。在30℃条件下,其对CO2的吸附量为54.1mg/g,随着温度的升高,吸附量有所降低,在100℃时,其对CO2的吸附量为31mg/g,吸附量的降低主要是由于碳酸盐的分解所致。     

Bi2O3助熔剂对CaO-B2O3-SiO2/Al2O3玻璃陶瓷复合材料性能的影响

以CaO-B₂O₃-SiO₂(CBS)玻璃粉体和Al₂O₃陶瓷粉体为原料,通过在CBS与Al₂O₃的质量比固定为50:50的玻璃-陶瓷复合材料中添加适量的Bi₂O₃作为烧结助熔剂,探讨了Bi₂O₃助熔剂对CBS/Al₂O₃复合材料的烧结性能、介电性能、抗弯强度和热膨胀系数的影响规律.研究表明:Bi₂O₃助熔剂能通过降低CBS玻璃的转变温度和黏度促进CBS/Al₂O₃复合材料的致密化进程,于880 ℃下烧结即能获得结构较致密、气孔较少的CBS/Al₂O₃复合材料.然而,过量添加Bi₂O₃将使玻璃的黏度过低,从而恶化CBS/Al₂O₃复合材料的烧结性能、介电性能及抗弯强度.当Bi₂O₃的添加量为CBS/Al₂O₃复合材料的1.5wt%时,于880 ℃下烧结即能获得最为致密的CBS/Al₂O₃复合材料,密度为2.82 g·cm^-3,这一材料具有良好的介电性能(介电常数为7.21,介电损耗为1.06×10^-3),抗弯强度为190.34 MPa,0~300 ℃的热膨胀系数为3.52×10^-6 K^-1.     

Effect of doping with Co2O3, TiO2, Fe2O3, and Mn2O3 on the properties of Ce0.8Gd0.2O2?δ

The effects of Co, Fe, Mn, and Ti oxide additions on the sinterability and crystal-chemical, thermal, and electrical properties of Ce_0.8Gd_0.2O_2−δ have been studied. The results indicate that these oxides enhance the sinterability of the mixed oxide, regardless of whether they were introduced before or after synthesis. The most effective sintering aid is Co₂O₃. The lattice parameters of Ce_0.8Gd_0.2O_2−δ samples containing different metal oxide additions (1 mol %) are refined in space group Fm3m. The temperature-dependent thermal expansion data are used to determine the linear thermal expansion coefficients of the samples. Manganese oxide additions reduce the electrical conductivity of Ce_0.8Gd_0.2O_2−δ, whereas the other dopants increase it in the order Ti < Fe < Co. The activation energy for conduction increases in the order Co < Ti < Fe < Mn. Original Russian Text ? E.Yu. Pikalova, A.N. Demina, A.K. Demin, A.A. Murashkina, V.E. Sopemikov, N.O. Esina, 2007, published in Neorganicheskie Material, 2007, Vol. 43, No. 7, pp. 830–837.     

The vibrational spectra of the intermediate compounds in the system Y2O3P2O5 and Gd2O3P2O5

The Infrared- and Raman-spectra of the intermediate compounds were studied for clues to their structural behavior as related to luminescence response. It was found that the degree of polymerization of PO₄ polyhedra increases in the phosphate-rich region and perhaps in the RE-oxide-rich region as well which was evident from the shift of stretching bands towards the higher energy side. Except in orthophosphates, the PO₄ polyhedra occupy more than one non-equivalent lattice site in all the phosphates.     

CoAl2O4/Al2O3纳米复合陶瓷的结构与表征

利用溶胶-凝胶方法制备了的CoAl2O4/Al2O3纳米复合陶瓷,并用X-ray分析(XRD)、红外光谱(IR)和扫描电镜分析(SEM)对其结构进行了分析.结果表明,随Al2O3含量增多,CoAl2O4尖晶石相从CoAl2O4/Al2O3凝胶中的析晶温度升高.SEM形貌也说明,随Al2O3含量增多,CoAl2O4/Al2O3陶瓷中形成一定的层状结构.     

Varistor properties of ZnO-Pr6O11-CoO-Cr2O3-Y2O3-In2O3 ceramics

The varistor properties of the ZnO-Pr₆O₁₁-CoO-Cr₂O₃-Y₂O₃-In₂O₃ ceramics were investigated for different concentrations of In₂O₃. The increase of In₂O₃ concentration slightly increased the sintered density (5.60-5.63 g/cm³) and slightly decreased the average grain size (3.4-2.9 μm). The breakdown field increased from 6023 to 14822 V/cm with increasing concentration of In₂O₃. The nonlinear coefficient increased from 17.6 to 44.6 for up to 0.005 mol%, whereas the further doping caused it to decrease to 36.8. In₂O₃ acted as an acceptor due to the donor concentration, which decreases in the range of 1.02 × 10¹⁷ to 0.24 × 10¹⁷/cm³ with increasing concentration of In₂O₃.     

La2O3、Nd2O3、Y2O3对高岭石高温相变动力学的影响

利用综合热分析技术、X射线衍射(XRD)、傅里叶变换红外光谱(FT-IR)和扫描电镜(SEM)研究了La_2O_3、Nd_2O_3、Y_2O_3对高岭石高温条件下转变成莫来石过程的作用,并采用Kissinger方程、Ozawa方程以及JMA修正方程(Ⅰ)和(Ⅱ)分析了La_2O_3、Nd_2O_3、Y_2O_3对高岭石高温相变动力学的影响。结果表明:3种稀土氧化物的掺入对高岭石的相变动力学参数产生了影响,相变活化能和频率因子与未掺入稀土氧化物的高岭石相比有所降低,析晶方式则未发生变化,均属于体积晶化。对比掺入3种稀土氧化物的高岭石相变活化能和频率因子可以看出,Y_2O_3对于高岭石高温条件下相变的促进作用最为明显,相变活化能最低。稀土氧化物对于高岭石高温相变产物影响不大,主晶相为莫来石相,次晶相为方石英相,但稀土氧化物的掺入使得方石英相的结晶度明显提高。     

Application of the wanklyn model to the BaOBaF2B2O3Y2O3Fe2O3 flux system

Data on the BaOBaF₂ B₂O₃ Y₂O₃ Fe₂O₃ flux system are analyzed in terms of the model recently proposed by Wanklyn, verified thus far for lead- and alkali- based fluxes. The model is found to hold, with the noticeable exception that in this particular case the basic oxide and the corresponding fluoride are not equivalent from the standpoint of phase equilibria: on the contrary, a BaF₂ addition makes “ineffective” a small but definite fraction of the BaO present in the melt.     

Al2O3颗粒形貌对注凝成型ZrO2/Al2O3陶瓷性能的影响

采用3种不同形貌的Al₂O₃原料对注凝成型制备ZrO₂/Al₂O₃（ZTA）陶瓷工艺中悬浮体的流变性能进行了研究。以低毒的单体N,N-二甲基丙烯酰胺（DMAA）制备了ZrO₂/Al₂O₃坯体和陶瓷。讨论了3种不同形貌的Al₂O₃原浆料的分散剂用量、球磨时间和固含量对浆料流变性的影响。Al₂O₃粉体呈扁平状有利于降低浆料的黏度,Al₂O₃粉体呈棒状对生坯强度的提高有利。制得的3种ZrO₂/Al₂O₃坯体颗粒间结合紧密,抗弯强度分别达到21.45,19.87,25.90 MPa。Al₂O₃粉体呈颗粒状有利于最终陶瓷力学性能的提高,陶瓷的抗弯强度及断裂韧性分别为680 MPa和7.49 MPa·m^1/2,453.1 MPa和6.8 MPa·m^1/2,549.4 MPa和6.34 MPa·m^1/2。     

Optimization of spectroscopic properties of Yb-doped refractory sesquioxides: cubic Y2O3, Lu2O3 and monoclinic Gd2O3

Absorption and emission spectra are given for Yb³⁺-doped Y₂O₃, Lu₂O₃ and Gd₂O₃ at room temperature. Y₂O₃ and Lu₂O₃ as close cubic matrices, show Yb³⁺ similar spectra different of Yb³⁺ in Gd₂O₃ monoclinic structure. Here, we use a new method to study and optimize the main spectroscopic properties with only one concentration gradient sample. Finally, assignments of Yb³⁺ Stark levels and Raman vibrations in Y₂O₃, Lu₂O₃ and Gd₂O₃ single crystal are given.     

Refractories based on 3Er2O3-Ta2O5

Refractory Er₂O₃-Ta₂O₅ compositions in the high Er₂O₃ region were prepared by coprecipitation as hydroxides, followed by calcination. Based on x-ray diffraction and wet chemical and electron microanalysis, the fluorite phase was found at 17.3–34.2 (±0.5) mole percent Ta₂O₅. This fluorite phase was stable to at least 2140 C in reducing atmospheres; although measurable vaporization occurred above 1975 C. Above 2100 C minor Ta reduction with preferential vaporization of Er and O was observed.