基于壳聚糖-纳米金/纳米普鲁士蓝/L-半胱氨酸修饰的 葡萄糖传感器的研究

在金电极表面修饰一层L-半胱氨酸,再利用静电吸附作用固定纳米普鲁士蓝(nano-PB),然后利用壳聚糖-纳米金复合膜将葡萄糖氧化酶(GOD)固定于修饰电极表面,制成新型的葡萄糖传感器.通过交流阻抗技术,循环伏安法和计时电流法考察了电极的电化学特性.在优化的实验条件下,该传感器在葡萄糖浓度为3.0×10-6～1.0×10-3 mol/L范围内有线性响应,检测下限为1.6×10-6 mol/L.此外该传感器具有响应快、稳定性好和选择性良好的特点,能有效排除常见干扰物质如抗坏血酸、尿酸等对测定的影响.     

L-半胱氨酸/纳米金/DNA/壳聚糖修饰金电极测定布洛芬

用电沉积和滴涂的方法依次将L-半胱氨酸、纳米金、DNA、壳聚糖修饰在金电极表面,制备了稳定性、响应性良好的修饰电极(L-Cys/Au colloid/DNA/CS/Au/CME)。考察了影响实验结果的关键因素,确定了最佳实验条件,进一步采用循环伏安法和差分脉冲伏安法研究了布洛芬在L-Cys/Au colloid/DNA/CS/Au/CME上的电化学行为。在最佳实验条件下,当布洛芬浓度在1.0×10~(-7)~1.0×10~(-4) mol/L范围内时相应的氧化还原峰电流与浓度呈现良好的线性关系,检出限(S/N=3)达2.3×10~(-8) mol/L。结果表明,该修饰电极对布洛芬有良好的响应性能,据此建立了一种测定布洛芬的新方法。     

L-半胱氨酸自组装膜修饰金电极对抗坏血酸的电催化作用及其测定

金电极表面对L 半胱氨酸 (L Cys)有特性吸附 ,而L Cys分子在等电点pH附近因静电引力和氢键作用形成分子对 ,从而在电极表面自组装形成L Cys双层膜。L Cys修饰金电极对抗坏血酸 (AA)具有良好的电催化作用。用示差脉冲伏安法对AA进行了测定 ,氧化电流与AA的浓度在 1.0× 10 -3 ～ 4× 10 -6mol/L范围内呈良好的线性关系 ,线性相关系数为 0 .9981;检出限为 4× 10 -7mol/L。用于药片中AA含量的测定 ,结果令人满意。     

细胞色素c在L-半胱氨酸自组装膜电极上的电化学行为

细胞色素c在L-半胱氨酸自组装膜电极上的电化学行为;细胞色素c; L-半胱氨酸; H2O2; 金电极     

桑色素在L-半胱氨酸自组装膜修饰金电极上的电化学行为研究

在0.1mol/L(pH=4.7)的HAc NaAc缓冲溶液中,用L 半胱氨酸自组装膜修饰金电极对桑色素的电化学行为进行了初步的研究,考察了修饰时间、富集时间、富集电位、扫描速度、表面活性剂、金属离子等因素对其电化学行为的影响。研究发现,桑色素在0.44V(vs.SCE)左右产生一不可逆的氧化峰。该氧化峰电流与桑色素浓度在5×10-6～2×10-4mol/L范围内呈线性关系(相关系数r=0.9989),检出限为2×10-6mol/L,这比用裸金电极测试降低一个数量级。同时发现,十六烷基三甲基溴化铵(CTAB)对氧化峰电流有一定的增敏作用。该峰且随Pb2+浓度增大而线性增高,因此可用于Pb2+的测定。     

L-半胱氨酸自组装电极循环伏安法测定多巴胺

建立了痕量多巴胺(DA)电化学分析方法.在pH 7.6的0.2 mol/L Na2HPO4-NaH2PO4 0.1 mol/L KCl底液中,L-半胱氨酸(L-Cys)自组装金电极对多巴胺有明显的电催化氧化作用,考察了该电极作为DA传感器的实验条件.结果表明:DA在L-Cys/Au电极上的氧化峰电流与多巴胺的浓度在一定范围内成线性关系,线性范围为6.7×10-5～4.6×10-3 mol/L,检出限为8.4×10-6 mol/L,平行测定8次,相对标准偏差为3.2%,用于盐酸多巴胺注射液中DA的测定,回收率为94%～96%.     

L-半胱氨酸改性Fe3O4纳米粒子的水热合成及其应用

以L-半胱氨酸为表面改性剂与粒径调节剂,采用水热法制备具有良好分散稳定性的磁性Fe₃O₄纳米粒子。通过透射电镜（TEM）、扫描电镜（SEM）、X射线衍射仪（XRD）、比磁饱和强度测定仪（VSM）等对产物进行表征,研究L-半胱氨酸对磁性Fe₃O₄纳米粒子的形貌、粒径分布、晶型结构、分散稳定性等的影响,理论推导了L-半胱氨酸改性后的Fe₃O₄纳米粒子（L-Fe₃O₄纳米粒子）的生成机制,将该材料作为载体吸附金种后探讨其在催化对硝基苯酚方面的应用。结果表明：沉降22 h时,调节pH值为7.0制备的Fe₃O₄纳米粒子的沉降高度大约是L-Fe₃O₄纳米粒子的6.5倍;吸附金种后的L-Fe₃O₄纳米粒子催化效率大约是未改性Fe₃O₄纳米粒子的5倍。L-半胱氨酸有效的改善了Fe₃O₄纳米粒子与分散介质之间的相容性,保护并改善了纳米粒子的分散稳定性,在污水处理等方面有潜在的应用。     

L-半胱氨酸自组装修饰金电极-不可逆双安培测定阿魏酸

在裸金电极上制备了L-半胱氨酸自组装膜金修饰电极(L-Cys/SAM-Au/CME),将自组装膜修饰电极用于不可逆双安培体系,利用阿魏酸在L-Cys/SAM-Au/CME上的氧化和KMnO4在裸金电极上的还原,构建双安培检测新体系,建立了在外加电压为0V条件下,流动注射双安培法直接测定阿魏酸的新方法。在0.05mol/LH2SO4溶液中,该氧化峰峰电流与阿魏酸浓度在5.0×10-7~8.0×10-5mol/L范围内呈线性关系(r=0.9961,n=10),其线性回归方程为i(nA)=4.16×107C 50,在1.0×10-4~1.0×10-3mol/L范围内呈线性关系(r=0.9955,n=5),其线性回归方程为i(nA)=5.6×106C 300,检出限为1.2×10-7mol/L。连续测定2.0×10-5mol/L阿魏酸溶液25次,电流值RSD为1.20%,进样频率为80样/h。该方法具有较宽的线性范围、较高的选择性和灵敏度,样品处理方法简单快速,适于在线分析。对阿魏酸钠盐注射液中阿魏酸的测定结果满意。     

L-半胱氨酸自组装膜修饰金电极的电化学特性

采用电化学石英晶体微天平（EQCM）和循环伏安法（CV）研究了L-半胱氨酸在金电极表面形成自组装膜的机理及其电化学性质.结果表明, L-半胱氨酸分子在金电极表面有特性吸附，而且在等电点pH附近因静电引力和氢键作用形成分子对，从而自组装形成双层膜.该膜电极在0.2 mol•L－1的醋酸缓冲溶液中，于－0.2～0.5 V(vs SCE)间CV扫描出现了一对稳定的氧化还原峰，并对抗坏血酸的氧化有良好的催化作用.     

基于纳米金自组装膜固定辣根过氧化物酶的生物传感研究

将辣根过氧化物酶(HRP)通过纳米技术和自组装技术固定于电极表面,制得了酶修饰电极.纳米金与HRP形成了静电复合物并高效地保持了HRP的生物活性,以对苯二酚作为电子媒介体,差示脉冲伏安法(DPV)研究生物酶电极测定H2O2的线性范围为5.0×10-6～1.0×10-3 mol/L,检测限为2.5×10-6 mol/L,线性方程为△I=0.34765+4.05553CH2O2(mM).酶电极的表观米氏常数(K(app))为0.0675 mmol/L.实验同时证明该生物酶电极具有良好的稳定性和使用寿命.     

An amperometric hydrogen peroxide biosensor based on immobilization of horseradish peroxidase on an electrode modified with magnetic dextran microspheres

A new kind of magnetic dextran microsphere (MDMS) with uniform shape and narrow diameter distribution has been prepared from magnetic iron nanoparticles and dextran. Horseradish peroxidase (HRP) was successfully immobilized on the surface of an MDMS-modified glassy-carbon electrode (GCE), and the immobilized HRP displayed excellent electrocatalytic activity in the reduction of H₂O₂ in the presence of the mediator hydroquinone (HQ). The effects of experimental variables such as the concentration of HQ, solution pH, and the working potential were investigated for optimum analytical performance. This biosensor had a fast response to H₂O₂ of less than 10 s and an excellent linear relationship was obtained in the concentration range 0.20 μmol L⁻¹–0.68 mmol L⁻¹, with a detection limit of 0.078 μmol L⁻¹ (S/N = 3) under the optimum conditions. The response showed Michaelis–Menten behavior at larger H₂O₂ concentrations, and the apparent Michaelis–Menten constant was estimated to be 1.38 mmol L⁻¹. Moreover, the selectivity, stability, and reproducibility of the biosensor were evaluated, with satisfactory results. Figure Amperometric response of the biosensor to successive additions of H₂O₂ and the plot of amperometric response vs. H₂O₂ concentration     

Biosensor for determination of hydrogen peroxide based on catalase activity of human erythrocytes

A hydrogen peroxide biosensor based on human erythrocytes is described. Erythrocytes are retained on the surface of an oxygen electrode by a semipermeable membrane. The response is based on the catalase activity of the erythrocytes. The sensitivity of 10^?4 mol 1^?1 and linearity from 1.5×10^?4 to 5×10^?3 mol^?1 are comparable to those of analogous enzyme biosensors for hydrogen peroxide determination. The greatest advantages of this biosensor are its easy preparation and a lifetime of 2 months together with good reproducibility (relative standard deviation <5%) and selectivity; only ascorbic acid appeared to interfere with the measurements.     

A new hydrogen peroxide biosensor based on gold nanoelectrode ensembles/multiwalled carbon nanotubes/chitosan film-modified electrode

Gold nanoelectrode ensembles were produced by electrodeposition using multiwalled carbon nanotubes (MWNTs) as template. A new third generation amperometric biosensor for hydrogen peroxide was developed based on adsorption of horseradish peroxidase (HRP) at the glassy carbon (GC) electrode modified with Au nanoelectrode ensembles/multiwalled carbon nanotubes/chitosan film. The resulting HRP biosensor offered an excellent detection for hydrogen peroxide at −0.11 V with a linear response range of 2.08 × 10⁻⁷ to 7.6 × 10⁻³ M with a correlation coefficient of 0.998, and response time <5 s. The detection limit was 1.02 × 10⁻⁷ M at 3σ. The biosensor displays rapid response, expanded linear response range, and excellent repeatability. The simple and fast fabrication of the sensor makes it superior to other techniques.     

Development of hydrogen peroxide biosensor based on in situ covalent immobilization of horseradish peroxidase by one-pot polysaccharide-incorporated sol-gel process

A simple and reliable one-pot approach was established for the development of a novel hydrogen peroxide (H₂O₂) biosensor based on in situ covalent immobilization of horseradish peroxidase (HRP) into biocompatible material through polysaccharide-incorporated sol-gel process. Siloxane with epoxide ring and trimethoxy anchor groups was applied as the bifunctional cross-linker and the inorganic resource for organic-inorganic hybridization. The reactivity between amine groups and epoxy groups allowed the covalent incorporation of HRP and the functional biopolymer, chitosan (CS) into the inorganic polysiloxane network. Some experimental variables, such as mass ratio of siloxane to CS, pH of measuring solution and applied potential for detection were optimized. HRP covalently immobilized in the hybrid matrix possessed high electrocatalytic activity to H₂O₂ and provided a fast amperometric response. The linear response of the as-prepared biosensor for the determination of H₂O₂ ranged from 2.0 × 10⁻⁷ to 4.6 × 10⁻⁵ mol l⁻¹ with a detection limit of 8.1 × 10⁻⁸ mol l⁻¹. The apparent Michaelis-Menten constant was determined to be 45.18 μmol l⁻¹. Performance of the biosensor was also evaluated with respect to possible interferences. The fabricated biosensor exhibited high reproducibility and storage stability. The ease of the one-pot covalent immobilization and the biocompatible hybrid matrix serve as a versatile platform for enzyme immobilization and biosensor fabricating.     

Hydrogen peroxide biosensor based on hemoglobin modified zirconia nanoparticles-grafted collagen matrix

A novel method for the immobilization of hemoglobin (Hb) and preparation of reagentless biosensor was proposed using a biocompatible non-toxic zirconia enhanced grafted collagen tri-helix scaffold. The formed membrane was characterized with UV-vis and FT-IR spectroscopy, scanning electron microscope and electrochemical methods. The Hb immobilized in the matrix showed excellent direct electrochemistry with an electron transfer rate constant of 6.46 s⁻¹ and electrocatalytic activity to the reduction of hydrogen peroxide. The apparent Michaelis-Menten constant for H₂O₂ was 0.026 mM, showing good affinity. Based on the direct electrochemistry, a new biosensor for H₂O₂ ranging from 0.8 to 132 μM was constructed. Owing to the porous structure and high enzyme loading of the matrix the biosensor exhibited low limit of detection of 0.12 μM at 3σ, fast response less than 5 s and high sensitivity of 45.6 mA M⁻¹ cm⁻². The biosensor exhibited acceptable stability and reproducibility. ZrO₂-grafted collagen provided a good matrix for protein immobilization and biosensing preparation. This method was useful for monitoring H₂O₂ in practical samples with the satisfactory results.     

The electrochemical behavior of hydrogen peroxide sensor based on new methylene blue as mediator

利用共价键合法,将新亚甲蓝(NMB)与辣根过氧化酶(HRP)修饰于玻碳电极表面,制成一种新型的电流型H2O2传感器。探讨了该传感器在0·1mol/L磷酸缓冲溶液(pH=7·0)中的电化学性质。结果表明,NMB作为介体能够有效地在辣根过氧化酶和电极之间传递电子。测得电子转移系数为0·861,表观反应速率常数为1·27s-1。研究了传感器对H2O2的响应及动力学性质,米氏常数为8·27μmol/L,线性响应范围为2·5~100μmol/L。同时研究了pH、缓冲容量及温度等因素对H2O2传感器的影响。     

Amperometric biosensor for hydrogen peroxide based on hemoglobin entrapped in titania sol-gel film

Hemoglobin (Hb) was entrapped in a titania sol-gel matrix and used as a mimetic peroxidase to construct a novel amperometric biosensor for hydrogen peroxide. The Hb entrapped titania sol-gel film was obtained with a vapor deposition method, which simplified the traditional sol-gel process for protein immobilization. The morphologies of both titania sol-gel and the Hb films were characterized using scanning electron microscopy (SEM) and proved to be chemically clean, porous, homogeneous. This matrix provided a biocompatible microenvironment for retaining the native structure and activity of the entrapped Hb and a very low mass transport barrier to the substrates. H₂O₂ could be reduced by the catalysis of the entrapped hemoglobin at −300 mV without any mediator. The reagentless H₂O₂ sensor exhibited a fast response (less than 5 s) and sensitivity as high as 1.29 mA mM⁻¹ cm⁻². The linear range for H₂O₂ determination was from 5.0×10⁻⁷ to 5.4×10⁻⁵ M with a detection limit of 1.2×10⁻⁷ M. The apparent Michaelis-Menten constant of the encapsulated hemoglobin was calculated to be 0.18±0.02 mM. The stability of the biosensor was also evaluated.     

A peroxidase-tetrathiafulvalene biosensor based on self-assembled monolayer modified Au electrodes for the flow-injection determination of hydrogen peroxide

The construction and performance under flow-injection conditions of an integrated amperometric biosensor for hydrogen peroxide is reported. The design of the bioelectrode is based on a mercaptopropionic acid (MPA) self-assembled monolayer (SAM) modified gold disk electrode on which horseradish peroxidase (HRP, 24.3 U) was immobilized by cross-linking with glutaraldehyde together with the mediator tetrathiafulvalene (TTF, 1 μmol), which was entrapped in the three-dimensional aggregate formed.

The amperometric biosensor allows the obtention of reproducible flow injection amperometric responses at an applied potential of 0.00 V in 0.05 mol L⁻¹ phosphate buffer, pH 7.0 (flow rate: 1.40 mL min⁻¹, injection volume: 150 μL), with a range of linearity for hydrogen peroxide within the 2.0 × 10⁻⁷–1.0 × 10⁻⁴ mol L⁻¹ concentration range (slope: (2.33 ± 0.02) × 10⁻² A mol⁻¹ L, r = 0.999). A detection limit of 6.9 × 10⁻⁸ mol L⁻¹ was obtained together with a R.S.D. (n = 50) of 2.7% for a hydrogen peroxide concentration level of 5.0 × 10⁻⁵ mol L⁻¹. The immobilization method showed a good reproducibility with a R.S.D. of 5.3% for five different electrodes. Moreover, the useful lifetime of one single biosensor was estimated in 13 days.

The SAM-based biosensor was applied for the determination of hydrogen peroxide in rainwater and in a hair dye. The results obtained were validated by comparison with those obtained with a spectrophotometric reference method. In addition, the recovery of hydrogen peroxide in sterilised milk was tested.     

Room temperature ionic liquid doped DNA network immobilized horseradish peroxidase biosensor for amperometric determination of hydrogen peroxide

A novel electrochemical H₂O₂ biosensor was constructed by embedding horseradish peroxide (HRP) in a 1-butyl-3-methylimidazolium tetrafluoroborate doped DNA network casting on a gold electrode. The HRP entrapped in the composite system displayed good electrocatalytic response to the reduction of H₂O₂. The composite system could provide both a biocompatible microenvironment for enzymes to keep their good bioactivity and an effective pathway of electron transfer between the redox center of enzymes, H₂O₂ and the electrode surface. Voltammetric and time-based amperometric techniques were applied to characterize the properties of the biosensor. The effects of pH and potential on the amperometric response to H₂O₂ were studied. The biosensor can achieve 95% of the steady-state current within 2 s response to H₂O₂. The detection limit of the biosensor was 3.5 μM, and linear range was from 0.01 to 7.4 mM. Moreover, the biosensor exhibited good sensitivity and stability. The film can also be readily used as an immobilization matrix to entrap other enzymes to prepare other similar biosensors. Figure Horseradish peroxidase (HRP) embedded in a 1-butyl-3-methylimidazolium tetrafluoroborate (BMIM·BF ₄ ) doped DNA network can be used to fabricate a HRP sensor for the determination of H₂O₂