Structure and photoluminescence properties of Er3+-doped TiO2-SiO2 powders prepared by sol-gel method

Er 3+-doped TiO 2-SiO 2 powders are prepared by the sol-gel method,and they are characterized by high resolution transmission electron microscopy (HR-TEM),X-ray diffraction (XRD) spectra,and Raman spectra of the samples.It is shown that the TiO 2 nanocrystals are surrounded by an SiO 2 glass matrix.The photoluminescence (PL) spectra are recorded at room temperature.A strong green luminescence and less intense red emission are observed in the samples when they are excited at 325 nm.The intensity of the emission,which is related to the defect states,is strongest at the annealing temperature of 800 C.The PL intensity of Er 3+ ions increases with increasing Ti/Si ratio due to energy transfer between nano-TiO 2 particles and Er 3+ ions.     

Preparation, structure and ferromagnetic properties of the nanocrystalline Ti1-xMnxO2 thin films grown by radio frequency magnetron co-sputtering

This paper reported that the Mn-doped TiO2 films were prepared by radio frequency （RF） magnetron cosputtering. X-ray diffraction measurements indicate that the samples are easy to form the futile structure, and the sizes of the crystal grains grow big and big as the Mn concentration increases. X-ray photoemlssion spectroscopy measurements and high resolution transmission electron microscope photographs confirm that the manganese ions have been effectively doped into the TiO2 crystal when the Mn concentration is lower than 21%. The magnetic property measurements show that the Ti1-xMnxO2 （x = 0.21） films are ferromagnetic at room temperature, and the saturation magnetization, coercivity, and saturation field are 16.0 emu/cm^3, 167.5 × 80 A/m and 3740 × 80 A/m at room temperature, respectively. The room-temperature ferromagnetism of the films can be attributed to the new futile Ti1-xMnxO2 structure formed by the substitution of Mn^4＋ for Ti^4＋ into the TiO2 crystal .lattice, and could be explained by O vacancy （Vo）-enhanced ferromagnetism model.     

Correlation between microstructure and optical properties of nano-crystalline TiO2 thin films prepared by sol-gel dip coating

Titanium dioxide thin films have been prepared from tetrabutyl-orthotitanate solution and methanol as a solvent by sol-gel dip coating technique. TiO₂ thin films prepared using a sol-gel process have been analyzed for different annealing temperatures. Structural properties in terms of crystal structure were investigated by Raman spectroscopy. The surface morphology and composition of the films were investigated by atomic force microscopy (AFM). The optical transmittance and reflectance spectra of TiO₂ thin films deposited on silicon substrate were also determined. Spectroscopic ellipsometry study was used to determine the annealing temperature effect on the optical properties and the optical gap of the TiO₂ thin films. The results show that the TiO₂ thin films crystallize in anatase phase between 400 and 800 °C, and into the anatase-rutile phase at 1000 °C, and further into the rutile phase at 1200 °C. We have found that the films consist of titanium dioxide nano-crystals. The AFM surface morphology results indicate that the particle size increases from 5 to 41 nm by increasing the annealing temperature. The TiO₂ thin films have high transparency in the visible range. For annealing temperatures between 1000 and 1400 °C, the transmittance of the films was reduced significantly in the wavelength range of 300-800 nm due to the change of crystallite phase and composition in the films. We have demonstrated as well the decrease of the optical band gap with the increase of the annealing temperature.     

Synthesis and photocatalytic properties of porous TiO2 films prepared by ODA/sol-gel method

Porous TiO₂ films were deposited on SiO₂ pre-coated glass-slides by sol-gel method using octadecylamine (ODA) as template. The amount of ODA in the sol played an important role on the physicochemical properties and photocatalytic performance of the TiO₂ films. The films prepared at different conditions were all composed of anatase titanium dioxide crystals, and TiO₂ crystalline size got larger with increasing ODA amount. The maximum specific surface area of 41.5 m²/g was obtained for TiO₂ powders prepared from titanium sol containing 2.0 g ODA. Methyl orange degradation rate was enhanced along with increasing ODA amount and reached the maximal value at 2.0 g addition of ODA. After 40 min of UV-light irradiation, methyl orange degradation rate reached 30.5% on the porous film, which was about 10% higher than that on the smooth film. Porous TiO₂ film showed almost constant activity with slight decrease from 30.5% to 28.5% after 4 times of recycles.     

Influence of annealing process on conductive properties of Nb-doped TiO2 polycrystalline films prepared by sol-gel method

Nb-doped TiO₂ (TNO) thin films were prepared by sol-gel dip-coating method with Nb content in a wide range of 0-20 at.%. The prepared films were preheated at 400 °C and then undertaken by two different post-annealing processes: (a) three times vacuum annealing and (b) multi-round annealing. The designed multi-round annealing was shown to be an effective way to improve the conductive properties of the films, compared to the traditional vacuum annealing process. The minimum resistivity reached approximately 0.5 Ω cm with Nb doping concentration around 12 at.%, and the carrier density increased with Nb-doping concentration until the critical point of 12 at.%, which might be the optimal doping content for our TNO films prepared by sol-gel method.     

N掺杂锐钛矿TiO2光学性能的第一性原理研究

用平面波赝势方法(PWP)计算了N掺杂锐钛矿型TiO₂前后的光学特性,即介电函数虚部ε₂(ω)，光学吸收系数I(ω)和反射率R(ω). 并从能带结构上解释了为什么掺N后锐钛矿型TiO₂的光学谱在2.93，3.56和3.97eV处相对掺杂前会出现3个峰值的原因. 从光谱图上分析得出，掺杂后TiO₂要发生红移现象，实验现象证实了这一结果. 关键词： N掺杂 2')" href="#">锐钛矿型TiO₂ 光学性能 第一性原理     

Effect of nickel doping on structural, optical and electrical properties of TiO2 nanoparticles by sol-gel method

Nickel-doped anatase TiO₂ nanoparticles have been prepared by sol-gel method. The X-ray powder diffraction study reveals that all the prepared samples have pure anatase phase tetragonal system. The average crystallite size of the prepared sample is 14 nm, when found through transmission electron microscope. A strong frequency dependence of both dielectric constant (?′) and dielectric loss (tan δ) were observed for various dopant levels at room temperature in the frequency range of 42 Hz to 5 MHz. At low frequency, the piling up of mobile charge carriers at the grain boundary produces interfacial polarization giving rise to high dielectric constant. The asymmetric shape of frequency dependence of the dielectric loss for the primary relaxation process is observed for each concentration. From the ac conductivity studies, the reduction in conductivity may arise due to the decreasing particle with the increase in Ni-dopant level.     

Microstructural, optical and photocatalytic properties of CdS doped TiO2 thin films

CdS doped TiO₂ thin films (with CdS content=0, 3, 6, 9 and 12 at%) were grown on glass substrates. The X-ray diffraction analysis revealed that the films are polycrystalline of monoclinic TiO₂ structure. The microstructure parameters of the films such as crystallite size (D_ν) and microstrain (e) are calculated. Both the crystallites size and the microstrain are decreased with increasing CdS content. The optical constants have been determined in terms of Murmann's exact equations. The refractive index and extinction coefficient are increased with increasing CdS content. The optical band gap is calculated in the strong absorption region. The possible optical transition in these films is found to be an allowed direct transition. The values of E_g^opt are found to decrease as the CdS content increased. The films with 3 at% CdS content have better decomposition efficiency than undoped TiO₂. The films with 6 at% and 9 at% CdS content have decomposition efficiency comparable to that of undoped TiO₂, although they have lower band gap. The CdS doped TiO₂ could have a better impact on the decomposing of organic wastes.     

萤石结构TiO2的电子结构和光学性质

利用第一性原理计算了立方相萤石TiO₂的晶胞参数,能带结构和电子态密度.结果显示萤石TiO₂属于间接带隙半导体材料,其间接禁带宽度(Γ→X)E_g为2.07eV,比常见的金红石和锐钛矿TiO₂的禁带宽度窄.为了更清楚地了解萤石的光学性质,利用Kramers-Kronig色散关系,分别对萤石和金红石TiO₂的复介电常数、吸收率等参数进行了计算,并将二者结果做了 关键词： 2')" href="#">萤石结构TiO₂ 密度泛函理论 能带结构 光学性质     

萤石结构TiO2的电子结构和光学性质

利用第一性原理计算了立方相萤石TiO₂的晶胞参数，能带结构和电子态密度.结果显示萤石TiO₂属于间接带隙半导体材料，其间接禁带宽度(Γ→X)E_g为2.07eV，比常见的金红石和锐钛矿TiO₂的禁带宽度窄.为了更清楚地了解萤石的光学性质，利用Kramers-Kronig色散关系，分别对萤石和金红石TiO₂的复介电常数、吸收率等参数进行了计算，并将二者结果做了     

Structural, optical and electrochemical properties of TiO2 thin films grown by APCVD method

Atmospheric pressure chemical vapor deposition (APCVD) of TiO₂ thin films has been achieved onto glass and onto ITO-coated glass substrates, from the reaction of TiCl₄ with ethyl acetate (EtOAc). The effect of the synthesis temperature on the optical, structural and electrochemical properties was studied through spectral transmittance, X-ray diffraction (XRD) and electrochemical impedance spectroscopy (EIS) measurements. It was established that the TiO₂ films deposited onto glass substrate, at temperatures greater than 400 °C grown with rutile type tetragonal structure, whereas the TiO₂ films deposited onto ITO-coated glass substrate grown with anatase type structure. EIS was applied as suitable method to determine the charge transfer resistance in the electrolyte/TiO₂ interface, typically found in dye-sensitized solar cells.     

Microstructures and magnetic properties of CoPt-TiO2 nanocomposite films prepared by annealing CoPt/TiO2 multilayers

CoPt-TiO₂ nanocomposite films were synthesized by rapid thermal annealing of CoPt/TiO₂ multilayers. The effects of annealing temperature, annealing time, Ag addition and TiO₂ volume fraction on the microstructures and magnetic properties of the CoPt-TiO₂ nanocomposite films were studied. Results showed that the ordering degree of CoPt and coercivity of CoPt-TiO₂ nanocomposites increased with annealing temperature. Increasing annealing time and Ag addition were able to increase the ordering degree and coercivity of CoPt. However, complete L1₀-ordering of CoPt at 550 °C annealing was not realized by increasing annealing time up to 30 min and Ag addition up to 30 vol.%. Increasing TiO₂ volume fraction at 700 °C annealing did not lead to the change of ordering of CoPt. However, the grain structure of the films changed slightly when TiO₂ volume fraction was larger than 56%. The coercivity of the film decreased slightly with the addition of TiO₂.     

Structural study of sol-gel Au/TiO2 films from nanopowders

TiO₂ represents one of the most important sol-gel materials, due to its photocatalytic properties, in the case of both powders and coatings. Nanostructured titania has been reported to be used in many applications in different fields ranging from optics to gas sensor via solar energy. Recent researches point out the existence of new procedures used in order to enhance the efficiency of the photocatalytic process. The metal ion doping is such an example. Two types of 2 wt.% Au containing TiO₂ powders have been embedded in sol-gel vitreous TiO₂ matrices. Au-doped TiO₂ films have been prepared from these sols, by dipping procedure using quartz microscopic slides, as substrates. The relationship between the synthesis conditions and the properties of titania nanosized materials, such as thermal stability, phase composition, crystallinity, and the influence of dopant was investigated. The hydrophilic properties of the films were correlated with their structure, composition and surface morphology.     

Surface roughness analysis of hydrophilic SiO2/TiO2/glass nano bilayers by the level crossing approach

The effect of etching time on the statistical properties of hydrophilic surfaces of SiO₂/TiO₂/glass nano bilayers has been studied using atomic force microscopy (AFM) and a stochastic approach based on a level crossing analysis. We have created rough surfaces of the hydrophilic SiO₂/TiO₂ nano bilayer system by using 26% potassium hydroxide (KOH) solution. Measuring the average apparent contact angle allowed us to assess the degree of hydrophilicity, and the optimum condition was determined to be 10 min etching time. A level crossing analysis based on AFM images provided deeper insight into the microscopic details of the surface topography. With different etching times, it has been shown that the average frequency of visiting a height with positive slope behaves in a Gaussian manner for heights near the mean value and obeys a power law for heights far away from the mean value. Finally, by applying the generalized total number of crossings with positive slope, it was found that the both high heights and deep valleys of the surface have a great effect on the hydrophilic degree of the SiO₂/TiO₂/glass nano bilayer investigated system.     

Annealing temperature effect on the properties of mercury-doped TiO2 films prepared by sol-gel dip-coating technique

This work presents the annealing temperature effect on the properties of mercury (Hg)-doped titanium dioxide (TiO₂). Thin films and polycrystalline powders have been prepared by sol-gel process. The structure, surface morphology and optical properties, as a function of the annealing temperature, have been studied by atomic force microscopy (AFM), Raman, reflectance and ellipsometric spectroscopies. In order to determine the transformation points, we have analyzed the xerogel-obtained powder by differential scanning calorimetry (DSC). Raman spectroscopy shows the crystalline anatase and rutile phases for the films annealed at 400 °C and 1000 °C respectively. The AFM surface morphology results indicate that the particle size increases from 14 to 57 nm by increasing the annealing temperature. The complex index and the optical band gap (E_g) of the films were determined by the spectroscopic ellipsometry analysis. We have found that the optical band gap decreases by increasing the annealing temperature.     

First-principles study of electronic structures and optical properties of Cu, Ag, and Au-doped anatase TiO2

We perform first-principles calculations to investigate the band structure, density of states, optical absorption, and the imaginary part of dielectric function of Cu, Ag, and Au-doped anatase TiO₂ in 72 atoms systems. The electronic structure results show that the Cu incorporation can lead to the enhancement of d states near the uppermost of valence band, while the Ag and Au doping cause some new electronic states in band gap of TiO₂. Meanwhile, it is found that the visible optical absorptions of Cu, Ag, and Au-doped TiO₂, are observed by analyzing the results of optical properties, which locate in the region of 400-1000 nm. The absorption band edges of Cu, Ag, and Au-doped TiO₂ shift to the long wavelength region compared with the pure TiO₂. Furthermore, according to the calculated results, we propose the optical transition mechanisms of Cu, Ag, and Au-doped TiO₂. Our results show that the visible light response of TiO₂ can be modulated by substitutional doping of Cu, Ag, and Au.     

锐钛矿相和金红石相TiO2:Nb的光电性能研究

采用基于密度泛函理论的第一性原理计算了锐钛矿相和金红石相TiO₂:Nb的晶体结构、电子结构和光学性质. 结果表明, 在相等的摩尔掺杂浓度下(6.25%), 锐钛矿相TiO₂:Nb的导带底电子有效质量小于金红石相TiO₂:Nb, 且前者室温载流子浓度是后者的两倍左右, 即具有更大的施主杂质电离率, 从而解释了锐钛矿相TiO₂:Nb比金红石相TiO₂:Nb具有更优异电学性能的实验现象. 光学计算也表明锐钛矿相在可见光区有更大的透过率, 从而在理论上解释了锐钛矿相TiO₂:Nb比金红石相TiO₂:Nb更适于做透明导电材料的原因. 计算结果与实验数据能较好符合. 关键词： 2:Nb')" href="#">TiO₂:Nb 第一性原理 电子结构 光学性能     

Morphology and natural wettability properties of sol-gel derived TiO2-SiO2 composite thin films

Previous studies suggest that granular interfaces induce a natural and persistent super-hydrophilicity in TiO₂-SiO₂ composite thin films deposited by sol-gel route. This effect enables to consider self-cleaning applications that do not require a permanent UV exposure, whereas such a permanent exposure is necessary for pure TiO₂ films. In this study, TiO₂-SiO₂ composite thin films have been deposited from a TiO₂ anatase crystalline suspension and different SiO₂ polymeric sols. Wettability studies show that a suitable control of the TiO₂-SiO₂ mixed sol formulations noticeably enhances persistence of the natural super-hydrophilicity in composite films. It is shown that, beside granular interface effects, modifications in the composite film morphologies can noticeably influence wettability properties.     

Structural, electrical and optical properties of TiO2 doped WO3 thin films

TiO₂ doped WO₃ thin films were deposited onto glass substrates and fluorine doped tin oxide (FTO) coated conducting glass substrates, maintained at 500 °C by pyrolytic decomposition of adequate precursor solution. Equimolar ammonium tungstate ((NH₄)₂WO₄) and titanyl acetyl acetonate (TiAcAc) solutions were mixed together at pH 9 in volume proportions and used as a precursor solution for the deposition of TiO₂ doped WO₃ thin films. Doping concentrations were varied between 4 and 38%. The effect of TiO₂ doping concentration on structural, electrical and optical properties of TiO₂ doped WO₃ thin films were studied. Values of room temperature electrical resistivity, thermoelectric power and band gap energy (E_g) were estimated. The films with 38% TiO₂ doping in WO₃ exhibited lowest resistivity, n-type electrical conductivity and improved electrochromic performance among all the samples. The values of thermoelectric power (TEP) were in the range of 23-56 μV/K and the direct band gap energy varied between 2.72 and 2.86 eV.     

锐钛矿相纳米TiO2晶体生长动力学及生长过程控制

研究了采用溶胶-凝胶法经由前驱物钛酸四异丙酯水解制备纳米TiO₂结构相变及锐钛矿晶体生长动力学过程. 研究结果表明,在酸性条件下水解,由于高压热处理温度的变化导致锐钛矿向金红石相的结构相变,锐钛矿相纳米TiO₂生长活化能在250℃以下和以上分别为(15.8±4.5)kJ/mol和(80.2±1.0)kJ/mol;而在碱性条件下水解的活化能值为(3.5±0.4)kJ/mol. 在不发生结构相变的条件下,酸性水解条件下锐钛矿相纳米TiO₂生长速 关键词： 2')" href="#">纳米TiO₂ 锐钛矿 生长动力学 溶胶-凝胶法