Effect of SiCnws on flexural strength of SiCf/HfC-SiC composites after impact and ablation

SiC nanowires (SiC_nws) modified SiC_f/HfC-SiC composites were prepared by precursor infiltration and pyrolysis (PIP) and chemical vapor infiltration (CVI) methods. The microstructure, flexural strengths, impact and impact-ablation tests of the composites with and without SiC_nws were investigated. The results showed that after introducing SiC_nws, not only the retention rate of HfC ceramic produced by PIP was increased obviously, but also the fracture displacement of the modified composites was reduced due to the enhancement effect of SiC_nws at interface between SiC fiber and matrix. After impact and impact-ablation, the strength retention of SiC_nws modified composites was 91.6 % and 69.1 % respectively, higher than that of the composites without SiC_nws (85.2 % and 54.8 %). As the impact resistance of the modified composites was improved by the pull-out and bridging of SiC_nws, the ablation resistance of the impacted composites was enhanced as well.     

The mechanical,thermophysical and electromagnetic properties of UD SiCf/SiC composites in different directions

Unidirectional (UD) silicon carbide (SiC) fiber-reinforced SiC matrix (UD SiC_f/SiC) composites with CVI BN interphase were fabricated by polymer infiltration-pyrolysis (PIP) process. The effects of the anisotropic distribution of SiC fibers on the mechanical properties, thermophysical properties and electromagnetic properties of UD SiC_f/SiC composites in different directions were studied. In the direction parallel to the axial direction of SiC fibers, SiC fibers bear the load and BN interphase ensures the interface debonding, so the flexural strength and the fracture toughness of the UD SiC_f/SiC composites are 813.0 ± 32.4 MPa and 26.1 ± 2.9 MPa·m^1/2, respectively. In the direction perpendicular to the axial direction of SiC fibers, SiC fibers cannot bear the load and the low interfacial bonding strengths between SiC fiber/BN interphase (F/I) and BN interphase/SiC matrix (I/M) both decrease the matrix cracking stress, so the corresponding values are 36.6 ± 6.9 MPa and 0.9 ± 0.5 MPa?m^1/2, respectively. The thermal expansion behaviors of UD SiC_f/SiC composites are similar to those of SiC fibers in the direction parallel to the axial direction of SiC fibers, and are similiar to those of SiC matrix in the direction perpendicular to the axial direction of SiC fibers. The total electromagnetic shielding effectiveness (EM SE_T) of UD SiC_f/SiC composites attains 32 dB and 29 dB when the axial direction of SiC fibers is perpendicular and parallel to the electric field direction, respectively. The difference of conductivity in different directions is the main reason causing the different SE_T. And the dominant electromagnetic interference (EMI) shielding mechanism is absorption for both studied directions.     

Effect of heat treatment on the microstructure and strength of yttrium silicate matrix-modified SiCf/SiC composites

Yttrium silicate was introduced into the matrix of SiC_f/SiC composites via the slurry impregnation and reactive chemical vapor infiltration (RCVI) methods to improve the water and oxygen corrosion resistance of the modified composite materials. The effects of heat treatment on the modified matrix and strength of the composites were systematically investigated. The results showed that the modified matrix was composed of a mixture of yttrium monosilicate, yttrium disilicate, and silicon carbide. The modified yttrium silicate matrix (named Y-Si-O matrix) and the silicon carbide matrix were laminated and well combined. After heat treatment, the amount of Y-Si-O in the mixed matrix increased. The modified composites with yttrium silicate had a similar flexural strength as SiC_f/SiC composites (∼400 MPa). After treated at 1000 °C – 1300 °C, the strength of the modified composites increased by 17 %–26 %. The highest strength was measured for composites treated at 1200 °C.     

Mechanical properties of SiCf/SiC composites with alternating PyC/BN multilayer interfaces

Alternating pyrolytic carbon/boron nitride (PyC/BN)_n multilayer coatings were applied to the KD–II silicon carbide (SiC) fibres by chemical vapour deposition technique to fabricate continuous SiC fibre-reinforced SiC matrix (SiC_f/SiC) composites with improved flexural strength and fracture toughness. Three-dimensional SiC_f/SiC composites with different interfaces were fabricated by polymer infiltration and pyrolysis process. The microstructure of the coating was characterised by scanning electron microscopy, X–photoelectron spectroscopy and transmission electron microscopy. The interfacial shear strength was determined by the single-fibre push-out test. Single-edge notched beam (SENB) test and three-point bending test were used to evaluate the influence of multilayer interfaces on the mechanical properties of SiC_f/SiC composites. The results indicated that the (PyC/BN)_n multilayer interface led to optimum flexural strength and fracture toughness of 566.0?MPa and 21.5?MPa?m^1/2, respectively, thus the fracture toughness of the composites was significantly improved.     

Effects of in-situ carbon layer and volume fraction of SiC fiber on the mechanical properties and fracture behaviors of SiCf/SiC composites fabricated by a modified PIP method

Unidirectional SiC_f/SiC composites (UD SiC_f/SiC composites) with excellent mechanical properties were successfully fabricated by a modified PIP method which involved the preparation of film-like matrix containing carbon layer with a low concentration PCS solution followed by the rapid densification of composites with a high concentration PCS solution. Carbon layers were in-situ formed and alternating with SiC layers in the as-received matrix. The unique microstructure endows the composites with appropriate interfacial bonding state, good load transfer ability of interphase and matrix and load bearing ability of fiber, and great crack deflection capacity, which ensures the synergy of high strength and toughness of composites. It is also found that the fiber volume fraction in the preform makes a non-negligible effect on the distribution of interphase and matrix, of which the reasonable adjustment can be utilized to optimize the mechanical properties of composites. Compared with the composites only using high concentration PCS solution, the UD SiC_f/SiC composites prepared by the modified PIP method exhibit superior mechanical properties. Ultrahigh flexural strength of 1318.5 ± 158.3 MPa and fracture toughness of 47.6 ± 5.6 MPa·m^1/2 were achieved at the fiber volume fraction of 30%.     

Effect of pyrolysis temperature on the mechanical evolution of SiCf/SiC composites fabricated by PIP

Three types of SiC_f/SiC composites with a four-step three-dimensional SiC fibre preform and pyrocarbon interface fabricated via precursor infiltration and pyrolysis at 1100 °C, 1300 °C, and 1500 °C were heat-treated at 1300 °C under argon atmosphere for 50 h. The effects of the pyrolysis temperature on the microstructural and mechanical properties of the SiC_f/SiC composites were studied. With an increase in the pyrolysis temperature, the SiC crystallite size of the as-fabricated composites increased from 3.4 to 6.4 nm, and the flexural strength decreased from 742 ± 45 to 467 ± 38 MPa. After heat treatment, all the samples exhibited lower mechanical properties, accompanied by grain growth, mass loss, and the formation of open pores. The degree of mechanical degradation decreased with an increase in the pyrolysis temperature. The composites fabricated at 1500 °C exhibited the highest property retention rates with 90% flexural strength and 98% flexural modulus retained. The mechanism of the mechanical evolution after heat treatment was revealed, which suggested that the thermal stability of the mechanical properties is enhanced by the high crystallinity of the SiC matrix after pyrolysis at higher temperatures.     

Fine study of hierarchical interphase constructed by boron nitride and carbon nanotubes in SiCf/SiC composites

A fine study of the interfacial part in the silicon carbide fiber (SiC_f) reinforced silicon carbide (SiC) composites was conducted by transmission electron microscopy. The boron nitride (BN) and carbon nanotubes (CNTs) were progressively coated on the SiC_f by chemical vapor deposition method to form a hierarchical structure. Three composites with different interfaces, SiC_f–CNTs/SiC, SiC_f@BN/SiC, and SiC_f@BN–CNTs/SiC, were fabricated by polymer infiltration and pyrolysis method. The interfaces and microstructures of the three composites were carefully characterized to investigate the improvement mechanism of strength and toughness. The results showed that BN could protect the surface of SiC_f from corrosion and oxidation so that improved the possibility of debonding and pullout. CNTs could avoid the propagation of cracks in the composites so that improved the damage resistance of the matrix. The synergistic reinforcement brought by BN and CNTs interfaces made the SiC_f@BN–CNTs/SiC composites with a tensile fracture strength as high as 359 MPa, with an improvement of 23% compared to that of SiC_f@BN/SiC.     

Ring compression properties of SiCf/SiC composites prepared by chemical vapor infiltration

SiC fiber reinforced SiC matrix (SiC_f/SiC) composites prepared by chemical vapor infiltration are one of promising materials for nuclear fuel cladding tube due to pronounced low radioactivity and excellent corrosion resistance. As a structure component, mechanical properties of the composites tubes are extremely important. In this study, three kinds of SiC_f preform with 2D fiber wound structure, 2D plain weave structure and 2.5D shallow bend-joint structure were deposited with PyC interlayer of about 150–200?nm, and then densified with SiC matrix by chemical vapor infiltration at 1050?°C or 1100?°C. The influence of preform structure and deposition temperature of SiC matrix on microstructure and ring compression properties of SiC_f/SiC composites tubes were evaluated, and the results showed that these factors have a significant influence on ring compression strength. The compressive strength of SiC_f/SiC composites with 2D plain weave structure and 2.5D shallow bend-joint structure are 377.75?MPa and 482.96?MPa respectively, which are significantly higher than that of the composites with 2D fiber wound structure (92.84?MPa). SiC_f/SiC composites deposited at 1100?°C looks like a more porous structure with SiC whiskers appeared when compared with the composites deposited at 1050?°C. Correspondingly, the ring compression strength of the composites deposited at 1100?°C (566.44?MPa) is higher than that of the composites deposited at 1050?°C (482.96?MPa), with a better fracture behavior. Finally, the fracture mechanism of SiC_f/SiC composites with O-ring shape was discussed in detail.     

Fabrication of a 3D4d braided SiCf/SiC composite via PIP process assisted with an EPD method

In order to improve the thermal conductivity and full-fill the gaps between the fiber bundles for three-dimensional four-directional (3D4d) braided SiC_f/SiC composites, 500?nm submicron-sized β-SiC particles were introduced into the 3D4d preform by an electrophoretic deposition (EPD) method. ζ-potential of the KD-Ⅱ SiC fibers and the aqueous suspension of the β-SiC particles were analyzed, as well as the efficiency of the deposition. After densified via PIP process, microstructure, three-point bending strength and thermal conductivity of the composite were investigated. The results showed that, SiC particles filled the gaps between the SiC fiber bundles efficiently, and thermal conductivity of the composites fabricated through PIP process assisted by EPD was 2.3 times that of the composites fabricated via PIP only. The bending strength of the EPD-composites was 647.08?±?69.53?MPa, which decreased to 2/3 of that of the composites manufactured only by PIP, owing to the reduction of fiber volume fraction and the damages to the interface coatings and fibers under the action of the electric field.     

Multifunctional nanocomposites integrate electromagnetic shielding,thermal, mechanical,and wear resistance properties

The SiC_nws/SiC nanocomposites were in situ synthesized by using nickel carbon foam as catalyst and skeleton. This technique has a series of advantages including simple operation, low cost, and high efficiency. Due to the excellent microwave absorption and thermal properties of SiC_nws, SiC_nws/SiC nanocomposites possess excellent electromagnetic shielding performance with a high SE_T value of 38.3 dB and good thermal properties with thermal conductivity of 13.77 ± 0.098 wm⁻¹k⁻¹ at room temperature. Meanwhile, the bending strength of the nanocomposites is 110.9 ± 7.7 MPa. The friction coefficient of nanocomposites is about 0.26 with a wear speed of about 67 um³/s. Therefore, the nanocomposites integrate many advantages including lightweight (2.0 g/cm³), excellent electromagnetic shielding, good heat conduction, high strength, and wear resistance.     

Microstructure and mechanical properties of quasi-isotropic chopped fiber-reinforced PyC–SiC matrix composite prepared by novel nondamaging method

In this work, quasi-isotropic chopped carbon fiber-reinforced pyrolytic carbon and silicon carbide matrix (C_f/C–SiC) composites and chopped silicon carbide fiber-reinforced silicon carbide matrix (SiC_f/SiC) composites were prepared via novel nondamaging method, namely airlaid process combined with chemical vapor infiltration. Both composites exhibit random fiber distribution and homogeneous pore size. Young's modulus of highly textured pyrolytic carbon (PyC) matrix is 23.01 ± 1.43 GPa, and that of SiC matrix composed of columnar crystals is 305.8 ± 9.49 GPa in C_f/C–SiC composites. Tensile strength and interlaminar shear strength of C_f/C–SiC composites are 52.56 ± 4.81 and 98.16 ± 24.62 MPa, respectively, which are both higher than those of SiC_f/SiC composites because of appropriate interfacial shear strength and introduction of low-modulus and highly textured PyC matrix. Excellent mechanical properties of C_f/C–SiC composites, particularly regarding interlaminar shear strength, are due to their quasi-isotropic structure, interfacial debonding, interfacial sliding, and crack deflection. In addition to the occurrence of crack deflection at the fiber/matrix interface, crack deflection in C_f/C–SiC composites takes also place at the interface between PyC–SiC composite matrix and the interlamination of multilayered PyC matrix. Outstanding mechanical properties of as-prepared C_f/C–SiC composites render them potential candidates for application as thermal structure materials under complex stress conditions.     

Excellent ablation resistance and reusability of silicon carbide fiber reinforced silicon carbide composite in dissociated air plasmas

This work explores the potentials of SiC fiber reinforced SiC matrix composites (SiC_f/SiC) with SiC coating to resist aerodynamic ablations for thermal protection purpose. A plasma wind tunnel is employed to evaluate their anti-ablation property in dissociated air plasmas. The results suggest a critical ablation temperature of SiC coated SiC_f/SiC, ≈ 1910 °C, which is the highest ever reported in literatures. Benefited by ‘all-SiC’ microstructures and relative flat ablated surfaces, the SiC_f/SiC is still ablation-resistant up to ≈ 1820 °C after the occurrence of ablation. This implies an excellent ablation resistance and reusability property of SiC_f/SiC, which surpasses that of traditional carbon fiber reinforced composites. Finally, an ablation mechanism dominated by surface characteristic is proposed. For the SiC coated SiC_f/SiC, ablation is prone to take place at surface cracks formed by thermal mismatch; while for the ablated SiC_f/SiC, ablation is triggered at the exposed fiber bundles which is over-heated in the plasmas.     

High-temperature mechanical properties and oxidation resistance of SiCf/SiC ceramic matrix composites with multi-layer environmental barrier coatings for turbine applications

Continuous silicon carbide fiber reinforced silicon carbide (SiC_f/SiC) ceramic matrix composites are considered promising materials as high-temperature components of advanced aero-engines. However, due to their susceptibility to oxidation and corrosion at high temperature, environmental barrier coatings (EBCs) must be applied on the surface of SiC_f/SiC. In this study, Si/Y₂SiO₅/LaMgAl₁₁O₁₉ (LMA) multi-layer EBCs were fabricated to protect SiC_f/SiC by using atmospheric plasma spraying (APS). The high-temperature tensile fatigue performance of SiC_f/SiC with and without EBCs was evaluated. The results indicated that EBCs significantly improved the tensile fatigue properties of SiC_f/SiC at high temperature in air atmosphere. Meanwhile the bending strength of specimens after isothermal aging or not was also tested. The multi-layer EBCs in this study may be a promising EBCs system for SiC_f/SiC after some improvements.     

Fabrication and mechanical behavior of ZrB2 strengthened SiCf/SiC composites prepared by hybrid processing route

A SiC fiber-reinforced composite containing a SiC-ZrB₂ mixed matrix (SiC_f/(SiC-ZrB₂)) with high density and enhanced mechanical properties was fabricated. ZrB₂ at 5 or 40?vol% was added to a (SiC + C) slurry to be infiltrated into the voids of 2D woven Tyranno?-SA grade-3 fabrics by electrophoretic deposition. Subsequent hot pressing at 1300?°C and 10?MPa for 1?h, followed by liquid silicon infiltration (LSI) at 1600?°C for 5?h in an Ar atmosphere resulted in the formation of the reaction-bonded SiC matrix, which revealed a composite density close to 97%. SiC_f/(SiC-ZrB₂) having open porosities of 0.2–0.6% showed peak strengths of 398 and 320?MPa for 5 and 40?vol% ZrB₂ addition, respectively. The large mismatch in the coefficient of thermal expansion and Young's modulus between the SiC and ZrB₂ phases was attributed to a reverse trend in the strength of composites. Brittle behavior of the composites in flexure can be explained by the strong bonding between the matrix and fibers formed by the reaction of interphase with molten Si during LSI. Strength retention after oxidation at 1000 and 1400?°C for 2?h was also compared in terms of ZrB₂ amount contained in the composites.     

Effect of intermediate heat treatment on mechanical properties of SiCf/SiC composites with BN interphase prepared by ICVI

SiC_f/SiC composites with BN interface were prepared through isothermal-isobaric chemical vapour infiltration process. Room temperature mechanical properties such as tensile, flexural, inter-laminar shear strength and fracture toughness (K_IC) were studied for the composites. The tensile strength of the SiC_f/SiC composites with stabilised BN interface was almost 3.5 times higher than that of SiC_f/SiC composites with un-stabilised BN interphase. The fracture toughness is similarly enhanced to 23 MPa m^1/2 by stabilisation treatment. Fibre push-through test results showed that the interfacial bond strength between fibre and matrix for the composite with un-stabilised BN interface was too strong (>48 MPa) and it has been modified to a weaker bond (10 MPa) due to intermediate heat treatment. In the case of composite in which BN interface was subjected to thermal treatment soon after the interface coating, the interfacial bond strength between fibre and matrix was relatively stronger (29 MPa) and facilitated limited fibre pull-out.     

Effect of SiC nanowires on the mechanical properties and thermal conductivity of 3D-SiCf/SiC composites prepared via precursor infiltration pyrolysis

In this study, SiC nanowires (SiC_NWS) were grown in situ on the surface of PyC interface through chemical vapor infiltration (CVI) to improve the mechanical characteristics and thermal conductivity of three-dimensional SiC_f/SiC composites fabricated via precursor infiltration pyrolysis (PIP). The effect of SiC_NWS on the properties of the obtained composites was investigated by comparing them with conventional SiC_f/PyC/SiC composites. After the deposition of SiC_NWS, the flexural strength of the SiC_f/SiC composites was found to increase by 46 %, and the thermal conductivity showed an obvious increase at 25?1000 °C. The energy release of the composites in the damage evolution process was analysed by acoustic emission. The results indicated that the damage evolution process was delayed owing to the decrease in porosity, the crack deflection and bridging of the SiC_NWS. Furthermore, the excellent thermal conductivity was attributed to the thermally conductive pathways formed by the SiC_NWS in the dense structure.     

Fabrication and optimization of 3D-Cf/HfC-SiC-based composites via sol-gel processing and reactive melt infiltration

In this work, 3D-C_f/HfC-SiC-based composites were fabricated and optimized via reactive melt infiltration (RMI) of Si into porous C_f/HfC-C preforms prepared by a sol-gel processing. The physical and chemical processes involved during the fabrication were identified and analyzed in details. It is revealed that fibers and interphase of the composites can be eroded during carbothermal reduction process, which can be further aggravated during RMI, with the formation of Hf-containing substance on the fibers surface. The fibers and interphase degradation is mainly induced by the reactions between HfO₂ and C/SiC interphase layers at elevated temperatures. Accordingly, a two-step carbothermal reduction treatment was proposed for the optimization of the fabrication procedure. As a result, less fiber/interphase erosion and improved mechanical properties are achieved in the composites, with the bending strength increased by ～49 % (from 214.1 ± 15.7 MPa to 319.0 ± 26.0 MPa).     

Mechanical,thermal, and dielectric properties of SiCf/SiC composites reinforced with electrospun SiC fibers by PIP

Electrospun unidirectional SiC fibers reinforced SiC_f/SiC composites (e-SiC_f/SiC) were prepared with ∼10% volume fraction by polymer infiltration and pyrolysis (PIP) process. Pyrolysis temperature was varied to investigate the changes in microstructures, mechanical, thermal, and dielectric properties of e-SiC_f/SiC composites. The composites prepared at 1100 °C exhibit the highest flexural strength of 286.0 ± 33.9 MPa, then reduced at 1300 °C, mainly due to the degradation of electrospun SiC fibers, increased porosity, and reaction-controlled interfacial bonding. The thermal conductivity of e-SiC_f/SiC prepared at 1300 °C reached 2.663 W/(m∙K). The dielectric properties of e-SiC_f/SiC composites were also investigated and the complex permittivities increase with raising pyrolysis temperature. The e-SiC_f/SiC composites prepared at 1300 °C exhibited EMI shielding effectiveness exceeding 24 dB over the whole X band. The electrospun SiC fibers reinforced SiC_f/SiC composites can serve as a potential material for structural components and EMI shielding applications in the future.     

Oxidation and microstructure of SiCf/SiC composites in moist air up to 1600°C by X-ray tomographic characterization

SiC_f/SiC composites that possess PyC or BN interface layers were fabricated and then oxidized in moist air at 1000, 1200, 1400, and 1600°C. High-resolution CT was used for capturing 3D images and quantifying the SiC phase, mesophase, and voids. The oxidation behavior and microstructural evolution of SiC_f/SiC with PyC or BN interface are discussed in this study. The microstructure of the SiC_f/SiC with a PyC layer was seriously damaged in moist air at high temperature, whereas the BN interface layer enhanced the oxidation resistance of the SiC_f/SiC. These results are also confirmed by using XRD, oxidation mass gain, tensile testing, and SEM measurements. The results of the oxidation behavior and microstructural evolution for SiC_f/SiC oxidized in dry air are also compared with the results of this study. Comparing the SiC_f/SiC with a PyC interface layer, the composite with a BN interface layer oxidized in moist air exhibits a high void growth rate and a low SiO₂ grain growth rate from 1000 to 1600°C. This work will provide guidance for predicting the service life of SiC_f/SiC for multiscale damage rate models of materials at a local scale and will also provide guidance on the life service design of SiC_f/SiC materials.     

Effects of SiC/HfC ratios on the ablation and mechanical properties of 3D Cf/HfC-SiC composites

Effects of SiC/HfC ratios on the ablation and mechanical properties of 3D C_f/HfC–SiC composites by precursor impregnation and pyrolysis (PIP) process were investigated systematically. Both strength (flexural and compressive strength) and modulus increase as the SiC/HfC ratio are improved. The compact and stiff HfC-SiC matrix in addition to the carbon fiber and PyC interphase with less reaction damage accounts for the improved mechanical properties of C_f/HfC-SiC with higher SiC/HfC ratios. Meanwhile, both weight loss and erosion depth of C_f/HfC-SiC are improved with the increased SiC/HfC ratios. Therefore, in order to balance the ablation and mechanical properties, an appropriate SiC/HfC ratio should be considered.