Salt-Induced Constructions of Gemini-like Surfactants at the Interface and Their Effects on the Interfacial Tension of a Water/Model Oil System

It is an urgent issue to enhance oil recovery for unconventional reservoirs with high salinity. Focused on this topic, salt addition is a powerful tool to motivate the surfactant assembly at the water/oil interface and improve the interfacial activity. We used a cationic surfactant cetyltrimethylammonium bromide (CTAB) and an anionic salt dicarboxylic acid sodium (CnDNa) to construct gemini-like surfactants at the interface and evaluated their ability to reduce the interfacial tension (IFT) between model oil (toluene and n-decane, v:v = 1:1) and water. Interestingly, the fabrication of a (CTAB)₂/C4DNa gemini-like surfactant was hardly achieved at the fresh water/model oil interface, but accomplished at the brine/model oil interface. At a high NaCl concentration (100,000 mg L⁻¹), the IFT value is reduced to 10⁻³ mN m⁻¹ order of magnitude, which is generally desired in practical applications. The control experiments displacing the surfactant type and the spacer length further confirmed the NaCl effects on the interfacial assembly.     

一种阴离子表面活性剂的合成与性能研究

合成了一种阴离子型双醚双苯磺酸盐Gemini表面活性剂,测定该系列Gemini表面活性剂水溶液的表面张力(γcmc)分别为:32.00mN/m、28.41 mN/m、29.76 mN/m、33.20 mN/m,临界胶束浓度(cmc)分别为:0.79mmol/L、0.87 mmol/L、1.02 mmol/L、0.84 mmol/L;该Gemini表面活性剂(DPDAS-12)可在无碱,浓度为0.35%条件下,将油/水界面张力降至1.2×10-3mN/m的超低水平;可有效改变岩石表面润湿性,可将亲油表面(θ=114°)改变为弱亲油(θ=69.3°),可将亲水表面(θ=26.0°)改变为弱亲水表面(θ=34.0°)。     

驱油用表面活性剂AF性能评价及驱油效果研究

评价了脂肪酸烷醇酰胺表面活性剂AF的界面张力和乳化性能,利用岩心驱替实验对其提高采收率效果进行了研究。结果表明,在模拟地层水的矿化度为5 119.63 mg/L时,AF浓度为0.2%～1.2%,其界面张力均能达到超低值;NaCl浓度为0.4%～2%,AF有效浓度为0.3%～0.6%时,体系的界面张力均能达到10-3mN/m数量级。AF具有较好的乳化原油的能力,在浓度为0.5%时,形成的O/W乳状液的稳定性最强,液滴粒径最小。岩心驱替实验表明,AF表面活性剂可在水驱基础上提高原油采收率20%以上,提高采收率效果明显,具有良好的应用前景。     

Novel surfactants for ultralow interfacial tension in a wide range of surfactant concentration and temperature

This work investigates the possibility of injecting dilute aqueous solutions of novel surfactants into the Yibal field (Sultanate of Oman). This was accomplished through an experimental protocol based on the following criteria: (i) compatibility of the surfactants with the high-saline reservoir water (∼200 g/L); (ii) low interfacial tension (IFT) between crude oil and reservoir water (less than 10⁻² mN m⁻¹); and (iii) maintaining the low IFT behaviour during the entire surfactant flooding. Novel surfactants selected in this study consist of a series of ether sulfonates (AES-205, AES-128, AES-506, and 7–58) and an amphoteric surfactant (6–105). These surfactants were found to be compatible with reservoir water up to 0.1% surfactant concentration, whereas 6–105 and 7–58 showed compatibility within the full range of surfactant concentration investigated (0.001–0.5%). All surfactant systems displayed dynamic IFT behavior, in which ultralow transient minima were observed in the range 10⁻⁴–10⁻³ mN m⁻¹, followed by an increase in the IFT to equilibrium values in the range 10⁻³–10⁻¹ mN m⁻¹. The results also showed that with respect to concentration (0.05–0.5%) and temperature (45–80°C), AES-205 and 7–58 surfactants exhibit a wide range of applicability, with the IFT remaining below 10⁻² mN m⁻¹, as required for substantial residual oil recovery. In addition, ultralow IFT were obtained at surfactant concentrations as low as 0.001%, making the use of these surfactants in enhanced oil recovery extremely cost-effective.     

A Star-Shaped Anionic Surfactant: Synthesis,Alkalinity Resistance,Interfacial Tension and Emulsification Properties at the Crude Oil–Water Interface

In this research, a star‐shaped surfactant was synthesized through the chlorination reaction, alkylation reaction and sulfonation reaction of triethanolamine, which is composed of three hydrophobic chains and three sulfonate hydrophilic groups. The critical micelle concentration (CMC) of the surfactant was measured by the surface tension method, and the results showed that it had high surface activity with CMC of 5.53 × 10^?5 mol/L. The surfactant was superior in surface active properties to the reference surfactants SDBS and DADS‐C₁₂. The interfacial tension (IFT) of the studied crude oil–water system (surfactant concentration 0.1 g/L, NaOH concentration 0.5 g/L, and experimental temperature 50 °C) dropped to 1.1 × 10^?4 mN/m, which can fulfil the requirement of surfactants for oil displacement. An aqueous solution of the surfactant and crude oil was emulsified by shaking, which formed a highly stable oil‐in‐water (O/W) emulsion with particle size of 5–20 μm. The oil displacement effect was almost 12%.     

Optimization of Dynamic Interfacial Tension for Crude Oil–Brine System in the Presence of Nonionic Surfactants

In this study, interfacial tension (IFT) is measured between brine and crude oil (a sample of heavy oil from an Iranian oil reservoir) in the presence of two nonionic surfactants, KEPS 80 (Tween 80) and Behamid D, at different concentrations in order to optimize the concentrations of the surfactants. The surface response method is used to design the IFT measurement experiments. The experimental design and optimization is performed using the IFT as an objective function and temperature, concentration, and time as independent variables. In addition to the IFT measurement, various experiments such as stability tests of the surfactants in NaCl brine solutions, adsorption experiments on the carbonated rock surface, and phase behavior tests are performed to investigate the behavior of KEPS 80 and Behamid D in the enhanced oil recovery process. At the end, a model using the response surface statistical technique is designed for optimization of the concentrations of the surfactants, and a surfactant molecular migration mechanism is used for explanation of the dynamic IFT variation versus time. In the case of IFT experiments, the effect of surfactant concentration (at 1000, 3000, and 5000 ppm) on the dynamic IFT is investigated. The experiments are performed at four temperatures (25, 40, 50, and 67°C). The results show that the oil–brine IFT values can be reduced to about 4 mN m⁻¹ in the presence of Behamid D and to about 1 mN m⁻¹ in the presence of KEPS 80 at low concentrations.     

Superior enhancement of imbibition recovery by novel surfactant mixtures with a large hydrophobic group combined with nanosilica

Low interfacial tension (IFT) drainage and imbibition are effective methods for improving oil recovery from reservoirs that have low levels of oil or are tight (i.e., exhibit low oil permeability). It is critical to prepare a high efficient imbibition formula. In this work, a novel 2,4,6-tris(1-phenylethyl)phenoxy polyoxyethylene ether hydroxypropyl sodium sulfonate (TPHS) surfactant was synthesized and evaluated for imbibition. Its structure was confirmed by Fourier transform infrared spectroscopy and the interfacial tension (IFT) of the crude oil/0.07% TPHS solution was 0.276 mN/m. When 0.1 wt% TPHS was mixed with 0.2 wt% alpha olefin sulfonate (AOS), the IFT was lowered to 6 × 10⁻² mN/m. The synergy between nanoparticles (NPs) and TPHS/AOS mixed surfactant was studied by IFT, contact angle on sandstone substrates, zeta potential, and spreading dynamics through microscopic methods. The results show that the surfactant likely adsorbs to the NP surface and that NP addition can help the surfactant desorb crude oil from the glass surface. With the addition of 0.05 wt% SiO₂ NPs (SNPs), the imbibition oil recovery rate increased dramatically from 0.32%/h to 0.87%/h. The spontaneous imbibition recovery increased by 4.47% for original oil in place (OOIP). Compared to flooding by TPHS/AOS surfactant solutions, the oil recovery of forced imbibition in the sand-pack increased by 12.7% OOIP, and the water breakthrough time was delayed by 0.13 pore volumes (PV) when 0.05% SNPs were added. This paper paves the way for enhanced oil recovery in low-permeability sandstone reservoirs using novel TPHS/AOS surfactants and SNPs.     

耐温抗盐表面活性剂溶液与原油的界面张力

研究了二甘醇双(α-磺酸钠)烷基羧酸酯(DMES-n)、十二烷基二甲基胺乙内酯(BS-12)两类表面活性剂与原油的界面张力,并考察了表面活性剂的耐温抗盐性。实验结果表明,DMES-n能将油水界面张力降低至10-2mN/m数量级,但是抗盐性不如BS-12;将两者复配后,在NaCl浓度为30 000～100 000 mg/L、MgCl2和CaCl2浓度为10 000 mg/L的条件下,DMES-14/BS-12和DMES-16/BS-12复配体系都能将油水界面张力降低至10-3mN/m数量级,表明复配体系既具有更好的降低界面张力的能力,同时还具有良好的抗高盐、高钙镁性能以及良好的耐温性。     

Gemini表面活性剂/醇/正辛烷/盐水体系微乳液的研究

以壬基酚为原料在催化剂存在下与二溴烷烃作用生成双醚,然后磺化,合成了一类Gemini阴离子表面活性剂,用悬滴法测定了其油水界面张力,结果表明,Gemini表面活性剂可使油水界面张力降低到 10-3mN/m。研究了Gemini表面活性剂 /醇 /正辛烷 /盐水体系的微乳液相行为,通过拟三元相图的方法确定了助表面活性剂醇的种类,实验结果表明,链长的比链短的醇具有更好的助活作用。通过正交实验方法得到了形成中相微乳液的最佳组成:w(GeminiD) =0 1%;w(n C6H13OH) =4 0%;w(NaCl) =1 5%。     

Surfactant-assisted aqueous extraction of palm-pressed mesocarp fiber residual oil with Tween 80 solution

The potential of Tween 80, a commercial food-grade non-ionic surfactant, was evaluated for the extraction of residual oil from palm-pressed mesocarp fibre (PPMF). Results show that the critical micelle concentration (CMC) was achieved at 0.05 wt% surfactant with an interfacial tension (IFT) of 0.51 mN/m. The extraction yield however depends not only on the IFT but also on the viscosity and the solid to liquid ratio of the extracting solution. The highest percentage of oil extraction (47.36%) was obtained at 1 wt% Tween 80 with 6% NaCl, temperature of 60°C and a solid–liquid ratio of 8 g PPMF: 200 g solution.     

Preparation and Characterization of an Anionic Gemini Surfactant for Enhanced Oil Recovery in a Hypersaline Reservoir

A new type of anionic Gemini surfactant (AGS) was designed and prepared by a simple, low–cost, and green method, and its properties were characterized. The results showed that the values of parameters such as critical micelle concentration (CMC) value, Γmax, Amin, and pC20 of AGS were 0.10 mmol L⁻¹, 1.62 mmol m⁻², 1.02 nm², and 4.60, respectively, indicating that AGS is highly surface active. AGS has a very good synergistic effect with lauryl diethanol amide (6501), and the mixture surfactant 6501DA (composed of AGS and 6501 with a mass ratio of 1:2.5) has good wetting and emulsifying ability of the crude oil and good resistance to calcium and magnesium ions. In the temperature range from 50 to 70 °C, salinity of 20,000–50,000 mg L⁻¹ of the simulated formation water, and dosage of 6501DA from 500 to 3000 mg L⁻¹, all the interfacial tension (IFT) values between the 6501DA solution and Bamianhe crude oil were lower than 10⁻² mN m⁻¹, and all the adsorption amounts of oil sand to 6501DA in solution were less than 2 mg g⁻¹, indicating that AGS has potential for application in EOR in a hypersaline reservoir.     

Characterizations of surfactant synthesized from Jatropha oil and its application in enhanced oil recovery

Surfactants are frequently used in chemical enhanced oil recovery (EOR) as it reduces the interfacial tension (IFT) to an ultra‐low value and also alter the wettability of oil‐wet rock, which are important mechanisms for EOR. However, most of the commercial surfactants used in chemical EOR are very expensive. In view of that an attempt has been made to synthesis an anionic surfactant from non‐edible Jatropha oil for its application in EOR. Synthesized surfactant was characterized by FTIR, NMR, dynamic light scattering, thermogravimeter analyser, FESEM, and EDX analysis. Thermal degradability study of the surfactant shows no significant loss till the conventional reservoir temperature. The ability of the surfactant for its use in chemical EOR has been tested by measuring its physicochemical properties, viz., reduction of surface tension, IFT and wettability alteration. The surfactant solution shows a surface tension value of 31.6 mN/m at its critical micelle concentration (CMC). An ultra‐low IFT of 0.0917 mN/m is obtained at CMC of surfactant solution, which is further reduced to 0.00108 mN/m at optimum salinity. The synthesized surfactant alters the oil‐wet quartz surface to water‐wet which favors enhanced recovery of oil. Flooding experiments were conducted with surfactant slugs with different concentrations. Encouraging results with additional recovery more than 25% of original oil in place above the conventional water flooding have been observed. © 2017 American Institute of Chemical Engineers AIChE J, 63: 2731–2741, 2017     

Novel fluorinated surfactants for enhanced oil recovery in carbonate reservoirs

Novel surfactant‐polymer (SP) formulations containing fluorinated amphoteric surfactant (surfactant‐A) and fluorinated anionic surfactant (surfactant‐B) with partially hydrolyzed polyacrylamide (HPAM) were evaluated for enhanced oil recovery applications in carbonate reservoirs. Thermal stability, rheological properties, interfacial tension, and adsorption on the mineral surface were measured. The effects of the surfactant type, surfactant concentration, temperature, and salinity on the rheological properties of the SP systems were examined. Both surfactants were found to be thermally stable at a high temperature (90 °C). Surfactant‐B decreased the viscosity and the storage modulus of the HPAM. Surfactant‐A had no influence on the rheological properties of the HPAM. Surfactant‐A showed complete solubility and thermal stability in seawater at 90 °C. Only surfactant‐A was used in adsorption, interfacial tension, and core flooding experiments, since surfactant‐B was not completely soluble in seawater and therefore was limited to deionized water. A decrease in oil/water interfacial tension (IFT) of almost one order of magnitude was observed when adding surfactant‐A. However, betaine‐based co‐surfactant reduced the IFT to 10^?3 mN/m. An adsorption isotherm showed that the maximum adsorption of surfactant‐A was 1 mg per g of rock. Core flooding experiments showed 42 % additional oil recovery using 2.5 g/L (2500 ppm) HPAM and 0.001 g/g (0.1 mass%) amphoteric surfactant at 90 °C.     

Wettability alteration and reducing water blockage in tight gas sandstone reservoirs using mixed cationic Gemini/nonionic fluorosurfactant mixtures

The unrecovered hydraulic fracturing fluid will invade the matrix and induce water blockage, creating formation damage and hindering the oil or gas production rate. First, the synergistic effect of cationic Gemini surfactant (MQAS) and nonionic fluorosurfactant (N-2821) mixtures on reducing the surface tension and wettability alteration was investigated in this paper. The critical micelle concentration (CMC) of the surfactant mixture is one or two orders of magnitude lower than that of N-2821 and MQAS, indicating that the MQAS/N-2821 mixtures exhibit an apparent synergistic effect in reducing surface tension. Moreover, the maximal contact angle of MQAS/N-2821 mixtures reached 83.55° at α_N-2821 = 0.5, and the total surfactant concentration of 1 × 10⁻⁴ mol/L due to the adsorption of surfactant. The adsorption mechanism of surfactants on the surface of quartz sand was then examined. The adsorption kinetics is consistent with the pseudo-second-order model at different surfactant concentrations, while the Freundlich model is suitable for describing the adsorption behavior of surfactants on the sandstone surface. This finding indicates that surfactant adsorption is multilayered. The MQAS/N-2821 surfactant mixtures have excellent surfactant activity due to the relationship of the capillary pressure to the surface tension, pore radius, and contact angle; thus, the addition of surfactant mixtures can reduce the liquid saturation effectively. Furthermore, the sequential imbibition experiments indicate that MQAS/N-2821 mixtures alter the wettability of the core plug, which results from the adsorption of surfactants. Compared with brine water, the MQAS/N-2821 mixtures decreased the liquid saturation and increased the permeability recovery ratios of the core plug.     

The Effects of Dynamic Noncovalent Interaction between Surfactants and Additional Salt on the pH-Switchable Interfacial Tension Variations

The dynamic noncovalent interaction between the anionic surfactant sodium dodecyl benzene sulfonate (SDBS) and 1,3-diphenylguanidine (DPG) was employed to control the interfacial activity of the surfactant. At high HCl concentration (1000 mg L⁻¹), the SDBS/DPGⁿ⁺ system could reduce the water/oil interfacial tension (IFT) to 10⁻⁴ mN m⁻¹ order of magnitude, which was much lower than the IFT values in the SDBS/DPG⁺ system with a low HCl concentration (100 mg L⁻¹) and the individual SDBS system by three and four orders of magnitude, respectively. The pH-switchable protonation of amido groups in DPG molecules determines the SDBS/DPG molecular interaction and the amplitude of IFT reduction, which was confirmed by control experiments using two other surfactants (sodium dodecyl sulfate [SDS] and dodecyl trimethylammonium bromide [DTAB]). Moreover, the investigation of the NaCl and temperature effects on the IFT indicated the intensity of mixed SDBS/DPGⁿ⁺ adsorption layers at the water/oil interface.     

二元复合驱表面活性剂界面张力研究

研究了二元驱用植物改性羧酸盐表面活性剂SNHD与原油间的动态界面张力,并探讨了聚合物、矿化度、pH值以及时间对界面张力的影响。结果表明SNHD与原油的界面张力能达到超低值;聚合物对界面张力影响不大;矿化度对低活性剂浓度体系界面张力的影响较大,随矿化度增加,界面张力减小;体系的最佳pH值约为7。     

Interfacial Dynamic Properties and Dilational Rheology of Sulfonate Gemini Surfactant and its Mixtures with Quaternary Ammonium Bromides at the Air–Water Interface

The dynamic interfacial properties and dilational rheology of gemini sulfonate surfactant (SGS) and its mixtures with quaternary ammonium bromides (DTAB, CTAB) at the air–water interface were investigated using drop shape analysis. Results suggest that the adsorption process of these surfactants is diffusion-controlled at dilute concentrations, whereas the adsorption mechanism gradually shifts to a mixed kinetic-diffusion control with increasing surfactant concentration. The mixed surfactant system possesses the best surface activity when the molar ratios of SGS/DTAB and SGS/CTAB mixtures are 9:10. The formation of catanionic complexes shields the electrostatic repulsion between surfactant molecules and lowers the electrostatic adsorption barrier. Therefore, SGS/DTAB and SGS/CTAB mixtures exhibit higher adsorption rates than either component alone. The effects of oscillating frequency and surfactant concentration on the surface dilational properties of SGS, DTAB, CTAB, SGS/DTAB, and SGS/CTAB mixtures were also determined. As the oscillating frequency increases, the dilational elasticity of these surfactants gradually increases. The dilational elasticity peaks at a certain concentration, which is less than the critical micelle concentration (CMC). Results show that the dilational elasticity of SGS/DTAB and SGS/CTAB mixtures is higher than that of either component, resulting from the formation of a denser monomolecular adsorption layer at the air–water interface. Our study provides a basis for understanding the interaction mechanism of catanionic surfactant mixtures containing Gemini surfactant at the air–water interface.     

无机盐对磺酸盐型双子表面活性剂溶液表面性能的影响

在(30±0.2)℃下,用直接观察法、表面张力法和旋转液滴法考察了不同无机盐(NaCl、CaCl2和MgCl2)对磺酸盐型双子表面活性剂DJ溶液溶解性、临界胶束浓度(CMC)值和界面张力的影响。结果表明,磺酸盐型双子表面活性剂DJ具有良好的抗盐性,溶解度可以达到20 000 mg/L以上;在低盐度范围时(小于500 mg/L),随着无机盐质量浓度的增加,表面活性升高,CMC降低;随着阳离子(Na+、Ca2+和Mg2+)价数的增加,CMC降幅增大,且Ca2+的影响程度大于Mg2+;在无机盐质量浓度达到10 000 mg/L时,CMC呈上升趋势;无机盐的加入使溶液界面张力先降后升,然后趋于平稳。无机盐质量浓度在100～1 000 mg/L内,磺酸盐型双子表面活性剂DJ溶液的界面张力可以达到最低。     

Progress in research of sulfobetaine surfactants used in tertiary oil recovery

The synthesis of sulfobetaine surfactants and their application in tertiary oil recovery (TOR) are summarized in this paper. The synthesis of sulfobetaine surfactants was classified into three categories of single hydrophobic chain sulfobetaine surfactants, double hydrophobic chain sulfobetaine surfactants and Gemini sulfobetaine surfactants for review. Their application in TOR was classified into surfactant flooding, microemulsion flooding, surfactant/polymer (SP) flooding and foam flooding for review. The sulfonated betaine surfactants have good temperature resistance and salt tolerance, low critical micelle concentration (cmc) and surface tension corresponding to critical micelle concentration (γ_cmc), good foaming properties and wettability, low absorption, ultralow interfacial tension of oil/water, and excellent compatibility with other surfactants and polymers. Sulfobetaine surfactants with ethoxyl structures, hydroxyl and unsaturated bonds, and Gemini sulfobetaine surfactants will become an important direction for tertiary oil recovery because they have better interfacial activity in high-temperature (≥90°C) and high-salinity (≥10⁴ mg/L) reservoirs. Some problems existing in the synthesis and practical application were also reviewed.     

Viscoelastic Surfactants with High Salt Tolerance,Fast‐Dissolving Property,and Ultralow Interfacial Tension for Chemical Flooding in Offshore Oilfields

Injected chemical flooding systems with high salinity tolerance and fast‐dissolving performance are specially required for enhancing oil recovery in offshore oilfields. In this work, a new type of viscoelastic‐surfactant (VES) solution, which meets these criteria, was prepared by simply mixing the zwitterionic surfactant N‐hexadecyl‐N,N‐dimethyl‐3‐ammonio‐1‐propane sulfonate (HDPS) or N‐octyldecyl‐N,N‐dimethyl‐3‐ammonio‐1‐propane sulfonate (ODPS) with anionic surfactants such as sodium dodecyl sulfate (SDS). Various properties of the surfactant system, including viscoelasticity, dissolution properties, reduction of oil/water interfacial tension (IFT), and oil‐displacement efficiency of the mixed surfactant system, have been studied systematically. A rheology study proves that at high salinity, 0.73 wt.% HDPS/SDS‐ and 0.39 wt.% ODPS/SDS‐mixed surfactant systems formed worm‐like micelles with viscosity reaching 42.3 and 23.8 mPa s at a shear rate of 6 s^?1, respectively. Additionally, the HDPS/SDS and ODPS/SDS surfactant mixtures also exhibit a fast‐dissolving property (dissolution time <25 min) in brine. More importantly, those surfactant mixtures can significantly reduce the IFT of oil–water interfaces. As an example, the minimum of dynamic‐IFT (IFT_min) could reach 1.17 × 10^?2 mN m^?1 between the Bohai Oilfield crude oil and 0.39 wt.% ODPS/SDS solution. Another interesting finding is that polyelectrolytes such as sodium of polyepoxysuccinic acid can be used as a regulator for adjusting IFT_min to an ultralow level (<10^?2 mN m^?1). Taking advantage of the mobility control and reducing the oil/water IFT of those surfactant mixtures, the VES flooding demonstrates excellent oil‐displacement efficiency, which is close to that of polymer/surfactant flooding or polymer/surfactant/alkali flooding. Our work provides a new type of VES flooding system with excellent performances for chemical flooding in offshore oilfields.